An 18-bit sigma–delta switched-capacitor modulator using 4-order single-loop CIFB architecture

Oversampling sigma–delta(Σ–Δ)analog-to-digital converters(ADCs)are currently one of the most widely used architectures for high-resolution ADCs.The rapid development of integrated circuit manufacturing processes has allowed the realization of a high resolution in exchange for speed.Structurally,theΣ–ΔADC is divided into two parts:a front-end analog modulator and a back-end digital filter.The performance of the front-end analog modulator has a marked influence on the entireΣ–ΔADC system.In this paper,a 4-order single-loop switched-capacitor modulator with a CIFB(cascade-of-integrators feed-back)structure is proposed.Based on the chosen modulator architecture,the ASIC circuit is implemented using a chartered 0.35μm CMOS process with a chip area of 1.72×0.75 mm^2.The chip operates with a 3.3-V power supply and a power dissipation of 22 mW.According to the results,the performance of the designed modulator has been improved compared with a mature industrial chip and the effective number of bits(ENOB)was almost 18-bit.

A 16-bit sigma–delta modulator applied in micro-machined inertial sensors

A fourth-order low-distortion low-pass sigma-delta （∑△） modulator is presented for micro-machined inertial sensors. The proposed single-loop single-bit feedback modulator is optimized with a feed-forward path to decrease the nonlinearities and power consumption. The IC is implemented in a standard 0.6 μm CMOS technology and operates at a sampling frequency of 3.846 MHz. The chip area is 2.12 mm^2 with 23 pads. The experimental results indicate a signal-to-noise ratio （SNR） of 100 dB and dynamic range （DR） of 103 dB at an oversampling rate （OSR） of 128 with the input signal amplitude of-3.88 dBFS at 9.8 kHz; the power consumption is 15 raW at a 5 V supply.

A 0.6-V,69-dB subthreshold sigma–delta modulator

In this paper a 0.6 V, 14 bit/500 Hz subthreshold inverter-based sigma-delta modulator is proposed. In the first integrator of the modulator, a bootstrap switch is used to accomplish accurate signal sampling. Without a transconductor operational amplifier(OTA), the sigma-delta modulator adopts a cascode inverter in the subthreshold region to save power consumption. The modulator is fabricated with a 0.13μm CMOS mixed-signal process. The experiment results show that with the 0.6 V power supply it achieves a maximum SNDR of 69.7 dB and an ENOB of 11.3 bit, respectively, but only consumes 5.07 μw power dissipation.

A single die 1.2 V 55 to 95 dB DR delta sigma ADC with configurable modulator and OSR

A single die 1.2 V multi-stage noise shaping（Mash） 2-2 delta sigma analog to digital converter（ADC）for wide applications is implemented. The configurable Mash 2-2 modulator with a new decimation filter design is presented to achieve wide and high dynamic range（DR） for multiple practical applications. The novel modulator can be configured as a Mash 2-2 modulator for high precision or a 2-order modulator for low DR. The decimation filter is designed to select the OSR flexibly among cascaded integrator comb（CIC） filter and two half-band filters（HBF）. The serial peripheral interface（SPI） can be used to adjust the sampling frequency and the oversampling ratio（OSR）. The design was fabricated in a 0.13 m CMOS process with an area of 0.91 mm2and a total power of 5.2 mW. The measurement results show that the dynamic range（DR） of the proposed ADC can change from 55to 95 dB with the configurable OSR from 16 to 256. The spurious free dynamic range（SFDR） and signal-to-noise distortion ratio（SNDR） can get 99 dB and 86.5 dB, respectively.

A continuous-time/discrete-time mixed audio-band sigma delta ADC

This paper introduces a mixed continuous-time/discrete-time, single-loop, fourth-order, 4-bit audioband sigma delta ADC that combines the benefits of continuous-time and discrete-time circuits, while mitigating the challenges associated with continuous-time design. Measurement results show that the peak SNR of this ADC reaches 100 dB and the total power consumption is less than 30 mW.

Continuous time sigma delta ADC design and non-idealities analysis

A wide bandwidth continuous time sigma delta ADC is implemented in 130 nm CMOS. A detailed nonidealities analysis （excess loop delay, clock jitter, finite gain and GBW, comparator offset and DAC mismatch） is performed developed in Matlab/Simulink. This design is targeted for wide bandwidth applications such as video or wireless base-stations. A third-order continuous time sigma delta modulator comprises a third-order RC operational- amplifier-based loop filter and 3-bit internal quantizer operated at 512 MHz clock frequency. The sigma delta ADC achieves 60 dB SNR and 59.3 dB SNDR over a 16-MHz signal band at an OSR of 16. The power consumption of the CT sigma delta modulator is 22 mW from the 1.2-V supply.

A 18-mW,20-MHz bandwidth,12-bit continuous-time∑△modulator using a power-efficient multi-stage amplifier

A fourth-order continuous-time sigma delta modulator with 20-MHz bandwidth, implemented in 130- nm CMOS technology is presented. The modulator is comprised of an active-RC operational-amplifier based loop filter, a 4-bit internal quantizer and three current steering feedback DACs. A three-stage amplifier with low power is designed to satisfy the requirement of high dc gain and high gain-bandwidth product of the loop filter. Non-return- to-zero DAC pulse shaping is utilized to reduce clock jitter sensitivity. A special layout technique guarantees that the main feedback DAC reaches 12-bit match accuracy, avoiding the use of a dynamic element matching algorithm to induce excess loop delay. The experimental results demonstrate a 64.6-dB peak signal-to-noise ratio, and 66-dB dynamic range over a 20-MHz signal bandwidth when clocked at 480 MHz with 18-mW power consumption from a 1.2-V supply.

A 1.2-V,84-dB∑△ADM in 0.18-μm digital CMOS technology

A low power and low voltage∑△analog-to-digital modulator is realized with digital CMOS technology, which is due to full compensated depletion mode capacitors.Compared with mixed signal technology,this type of modulator is more compatible for pure digital applications.A pseudo-two-stage class-AB OTA is used in switchedcapacitor integrators for low voltage and low power.The modulator is realized in standard SMIC 0.18μm 1P6M digital CMOS technology.Measured results show that with 1.2 V supply voltage and a 6 MHz sample clock,the dynamic range of the modulator is 84 dB and the total power dissipation is 2460μW.