Rejection of Direct Blast Interference Based on Signal Phase-Matching Array Processing

In bistaic acoustic testing, there will be strong direct blast interference. An algorithm based on signal phase-matching array processing that rejects direct blast interference in bistatic acoustic testing has been studied, through which the object scattering signal is accurately extracted. Characteristics of bistatic acoustic testing and signal phase matching processing principle are fully integrated in this algorithm. Firstly, the direct blast interference is calculated from the receiving signal based on three subarrays signal phase matching processing. Secondly, the direct blast is rejected by subtraction from the receiving signal. In this way the limitations of the high signal to noise ratio that signal phase matching processing required for direct calculating the object scattering signal can be avoided. Simulation and sea trial results show that, when the ratio of signal to interference is greater than -20 dB, this algorithm of direct blast interference rejection based phase matching signal processing can accurately extract the object scattering signal.

A feedback control method for phase signal demodulation in fber-optic hydrophones

In the realm of acoustic signal detection,the identification of weak signals,particularly in the presence of negative signal-to-noise ratios,poses a significant challenge.This challenge is further heightened when signals are acquired through fiber-optic hydrophones,as these signals often lack physical significance and resist clear systematic modeling.Conventional processing methods,e.g.,low-pass filter(LPF),require a thorough understanding of the effective signal bandwidth for noise reduction,and may introduce undesirable time lags.This paper introduces an innovative feedback control method with dual Kalman filters for the demodulation of phase signals with noises in fiber-optic hydrophones.A mathematical model of the closed-loop system is established to guide the design of the feedback control,aiming to achieve a balance with the input phase signal.The dual Kalman filters are instrumental in mitigating the effects of signal noise,observation noise,and control execution noise,thereby enabling precise estimation for the input phase signals.The effectiveness of this feedback control method is demonstrated through examples,showcasing the restoration of low-noise signals,negative signal-to-noise ratio signals,and multi-frequency signals.This research contributes to the technical advancement of high-performance devices,including fiber-optic hydrophones and phase-locked amplifiers.

Four-Dimensional Signal Constellations Based on Binary Frequency-Shift Keying and <i>M</i>-ary Amplitude-Phase-Shift Keying

In this article, we give the construction of new four-dimensional signal constellations in the Euclidean space, which represent a certain combination of binary frequency-shift keying (BFSK) and M-ary amplitude-phase-shift keying (MAPSK). Description of such signals and the formulas for calculating the minimum squared Euclidean distance are presented. We have developed an analytic building method for even and odd values of M. Hence, no computer search and no heuristic methods are required. The new optimized BFSK-MAPSK (M = 5,6,···,16) signal constructions are built for the values of modulation indexes h =0.1,0.15,···,0.5 and their parameters are given. The results of computer simulations are also provided. Based on the obtained results we can conclude, that BFSK-MAPSK systems outperform similar four-dimensional systems both in terms of minimum squared Euclidean distance and simulated symbol error rate.

Improvement on polynomial Wigner-Ville distribution for detecting higher-order polynomial phase signal

To detect higher order polynomial phase signals （HOPPSs）, the smoothed-pseudo polynomial Wigner-Ville distribution （SP-PVCVD）, an improved version of the polynomial Wigner-Ville distribution （PVCVD）, is presented using a separable kernel. By adjusting the lengths of the functions in the kernel, the balance between resolution retaining and interference suppressing can be adjusted conveniently. The proposed method with merits of interference terms reduction and noise suppression can provide time frequency representation of better readability and more accurate instantaneous frequency （IF） estimation with higher order SP-PVfVD. The performance of the SP-PWVD is verified by computer simulations.

Single channel source separation of radar fuze mixed signal based on phase difference analysis

A new method based on phase difference analysis is proposed for the single-channel mixed signal separation of single-channel radar fuze.This method is used to estimate the mixing coefficients of de-noised signals through the cumulants of mixed signals,solve the candidate data set by the mixing coefficients and signal analytical form,and resolve the problem of vector ambiguity by analyzing the phase differences.The signal separation is realized by exchanging data of the solutions.The waveform similarity coefficients are calculated,and the time鈥攆requency distributions of separated signals are analyzed.The results show that the proposed method is effective.

Dual-Use Signal Design for Radar and Communication via Joint Orthogonal Signal and Phase Modulation

This paper proposes a new information modulation resorting to orthogonal signal and its phase for dual-function radar communication(DFRC)systems.Focusing on the standardized linear frequency modulation(LFM)signal by additional phase,a bank of signals enjoying satisfactory autocorrelation and cross-correlation characteristics,are generated.Then,these signals map the different information as well as their phases are also modulated to increase the communication bit rate,thus yielding a series of dual-use signals.Finally,the radar detection and communication performance of dual-use signals are also provided through numerical simulation and half-physical platform verification,confirming the effectiveness of the designed signals compared with the existing design strategy.

Polyphase coded signal design for MIMO radar using MO-MicPSO

A novel modified optimization technique known as the multi-objective micro particle swarm optimization（MO-MicPSO） is proposed for polyphase coded signal design.The proposed MO-MicPSO requires only a small population size compared with the standard particle swarm optimization that uses a larger population size.This new method is guided by an elite archive to finish the multi-objective optimization.The orthogonal polyphase coded signal（OPCS） can fundamentally improve the multiple input multiple output（MIMO） radar system performance,with which the radar system has high resolution and abundant signal channels.Simulation results on the polyphase coded signal design show that the MO-MicPSO can perform quite well for this high-dimensional multi-objective optimized problem.Compared with particle swarm optimization or genetic algorithm,the proposed MO-MicPSO has a better optimized efficiency and less time consumption.

Novel non-coherent integration method using binary phase-coded radar signal

The m series with 511 bits is taken as an example being applied in non-coherent integra- tion algorithm. A method to choose the bi-phase code is presented, which is 15 kinds of codes are picked out of 511 kinds of m series to do non-coherent integration. It is indicated that the power in- creasing times of larger target sidelobe is less than the power increasing times of smaller target main- lobe because of the larger target＇ s pseudo-randomness. Smaller target is integrated from larger tar- get sidelobe, which strengthens the detection capability of radar for smaller targets. According to the sidelobes distributing characteristic, a method is presented in this paper to remove the estimated sidelobes mean value for signal detection after non-coherent integration. Simulation results present that the SNR of small target can be improved approximately 6. 5 dB by the proposed method.

Signal-to-noise ratio comparison of angular signal radiography and phase stepping method

Grating-based x-ray phase contrast imaging has the potential to be applied in future medical applications as it is compatible with both laboratory and synchrotron source. However, information retrieval methods are important because acquisition speed, scanning mode, image quality, and radiation dose depend on them. Phase-stepping （PS） is a widely used method to retrieve information, while angular signal radiography （ASR） is a newly established method. In this manuscript, signal-to-noise ratios （SNRs） of ASR are compared with that of PS. Numerical experiments are performed to validate theoretical results. SNRs comparison shows that for refraction and scattering images ASR has higher SNR than PS method, while for absorption image both methods have same SNR. Therefore, our conclusions would have guideline in future preclinical and clinical applications.

SELECTION OF PROPER EMBEDDING DIMENSION IN PHASE SPACE RECONSTRUCTION OF SPEECH SIGNALS

In phase space reconstruction of time series, the selection of embedding dimension is important. Based on the idea of checking the behavior of near neighbors in the reconstruction dimension, a new method to determine proper minimum embedding dimension is constructed. This method has a sound theoretical basis and can lead to good result. It can indicate the noise level in the data to be reconstructed, and estimate the reconstruction quality. It is applied to speech signal reconstruction and the generic embedding dimension of speech signals is deduced.

The Implementation and Lateral Control Optimization of a UAV Based on Phase Lead Compensator and Signal Constraint Controller

Unmanned Aero Vehicles (UAV) has become a useful entity for quite a good number of industries and facilities. It is an agile, cost effective and reliable solution for communication, defense, security, delivery, surveillance and surveying etc. However, their reliability is dependent on the resilient and stabilizes performance based on control systems embedded behind the body. Therefore, the UAV is majorly dependent upon controller design and the requirement of particular performance parameters. Nevertheless, in modern technologies there is always a room for improvement. In the similar manner a UAV lateral control system was implemented and researched in this study, which has been optimized using Proportional, Integral and Derivative (PID) controller, phase lead compensator and signal constraint controller. The significance of this study is the optimization of the existing UAV controller plant for improving lateral performance and stability. With this UAV community will benefit from designing robust controls using the optimized method utilized in this paper and moreover this will provide sophisticated control to operate in unpredictable environments. It is observed that results obtained for optimized lateral control dynamics using phase lead compensator (PLC) are efficacious than the simple PID feedback gains. However, for optimizing unwanted signals of lateral velocity, yaw rate, and yaw angle modes, PLC were integrated with PID to achieve dynamical stability.

Direct Digital Frequency Control Based on the Phase Step Change Characteristic between Signals

We present a new digital phase lock technology to achieve the frequency control and transformation through high precision multi-cycle group synchronization between signals without the frequency transformation circuit. In the case of digital sampling, the passing zero point of the phase of the controlled signal has the phase step characteristic, the phase step of the passing zero point is monotonic continuous with high resolution in the phase lock process, and using the border effect of digital fuzzy area, the gate can synchronize with the two signals, the quantization error is reduced. This technique is quite different from the existing methods of frequency transformation and frequency synthesis, the phase change characteristic between the periodic signals with different nominal is used. The phase change has the periodic phenomenon, and it has the high resolution step value. With the application of the physical law, the noise is reduced because of simplifying frequency transformation circuits, and the phase is locked with high precision. The regular phase change between frequency signals is only used for frequency measurement, and the change has evident randomness, but this randomness is greatly reduced in frequency control, and the certainty of the process result is clear. The experiment shows that the short term frequency stability can reach 10-12/s orders of magnitude.

Safety Performance Functions for Traffic Signals:Phasing and Geometry

A significant proportion of urban crashes,especially serious and fatal crashes,occur at traffic signals.Many of the black-spots in both Australia and New Zealand cities occur at high volume and/or high-speed traffic signals.Given this,crash reduction studies often focus on the major signalised intersections.However,there is limited information that links the phasing configuration,degree of saturation and overall cycle time to crashes.While a number of analysis tools are available for assessing the efficiency of intersections,there are very few tools that can assist engineers in assessing the safety effects of intersection upgrades and new intersections.Safety performance functions have been developed to help quantify the safety impact of various traffic signal phasing configurations and level of intersection congestion at low and high-speed traffic signals in New Zealand and Australia.Data from 238 signalised intersection sites in Auckland,Wellington,Christchurch,Hamilton,Dunedin and Melbourne was used to develop crash prediction models for key crash-causing movements at traffic signals.Different variables(road features)effect each crash type.The models indicate that the safety of intersections can be improved by longer cycle times and longer lost inter-green times,especially all-red time,using fully protected right turns and by extending the length of right turn bays.The exception is at intersections with lots of pedestrians where shorter cycle times are preferred as pedestrian crashes increase with longer wait times.A number of factors have a negative impact on safety including,free left turns,more approach lanes,intersection arms operating near or over capacity in peak periods and higher speed limits.

PHASE RETRIEVAL OF TIME-LIMITED SIGNALS

The problem of reconstructing a signalφ（x） from its magnitude ｜φ（x）] isof considerable interest to engineers and physicists. This article concerns the problem of determining a time-limited signal f with period 2π when ｜f（eix）l is known for x∈[-π,π]. It is shown that the conditions ｜g（eix）｜ = ｜f（eix）｜ and ｜g（ci（x＋b）） -g（eix）｜ =f（ei（x＋b）） - f（eix）｜, b ≠ 27π, together imply that either g = wf or g = v f, where both w and v have period b. Furthermore, if b/2π is irrational then the functions w and v b is rational then w takes the form reduce to some constants c1 and c2, respectively; ifb/2π is rational then w takes the form w=elexB1（e1x）B2（elx）and v takes the form ei（x2πN/b＋a）B1（elx）B2（elx）,where B1 and B2 are Blaschke products.

DOA estimation for mixed signals with gain-phase error array

Most of the direction of arrival(DOA) estimation methods often need the exact array manifold, but in actual applications,the gain and phase of the channels are usually inconsistent, which will cause the estimation invalid. A novel direction finding approach for mixed far-field and near-field signals with gain-phase error array is provided. Based on simplifying the space spectrum function by matrix transformation, DOA of far-field signals is obtained. Consequently, errors of the array are acquired according to the orthogonality of far-field signal subspace and noise subspace.Finally, DOA of near-field signals can be estimated. The method merely needs one-dimensional spectrum searching, so as to improve the computational efficiency on the premise of ensuring a certain accuracy, simulation results manifest the effectiveness of the method.

对瞬时测频干扰机理的研究

瞬时测频(instantaneous frequency measurement,IFM)接收机是电子侦察中非常重要的测频资源,其结构简单、灵敏度高、侦察频带宽、分辨率高,可以快速测定被测信号的频率,在现代电子战中得到广泛应用。基于IFM微波鉴相器在某一瞬间只能响应一个信号的特性,结合IFM工作原理,研究了一种新的(超过2个信号)对IFM干扰策略,并分析了干扰机理,通过模拟仿真对IFM的干扰效果进行了评估。仿真结果表明:多信号交叠可以对IFM系统产生明显的干扰效果,可以使得其无法测得正确频率,并错误地输出同时到达信号指示。

DDFS spurious signals due to amplitude quantization in absence of phase-accumulator truncation

Spurious signals in direct digital frequency synthesizers （DDFSs） are partly caused by amplitude quantization and phase truncation, which affect their application to many wireless telecommunication systems. These signals are deterministic and periodic in the time domain, so they appear as line spectra in the frequency domain. Two types of spurious signals due to amplitude quantization are exactly formulated and compared in the time and frequency domains respectively. Then the frequency spectra and power levels of the spurious signals due to amplitude quantization in the absence of phase-accumulator truncation are emphatically analyzed, and the effects of the DDFS parameter variations on the spurious signals are thoroughly studied by computer simulation. And several important conclusions are derived which can provide theoretical support for parameter choice and spurious performance evaluation in the application of DDFSs.

基于Labview的分布式光纤光栅信号解调技术研究

分布式光纤光栅信号解调中受到通信信道的码间干扰导致信道均衡性不好,提出基于Labview的分布式光纤光栅信号解调技术。采用连续时间采样技术构建分布式光纤光栅信号采集模型,对信号输出的功率谱密度特征进行相位调制处理,在离散的维纳模型下提取分布式光纤光栅信号的偏移中心频率和单边带功率谱密度特征信息,通过Labview的调制解调技术实现对信号的调制解调处理,最后采用抗相位噪声干扰的星座图分析方法分析光纤光栅信号解调的抗干扰性和误码抑制能力。仿真结果得知,该方法进行分布式光纤光栅信号解调的抗干扰性较好,提高了信道的频谱带宽,降低了频率中心偏移,传输误码率低于0.05%,信号的传输延时维持在30μs左右,具有较强的应用性。

Gearbox Fault Diagnosis using Adaptive Zero Phase Time-varying Filter Based on Multi-scale Chirplet Sparse Signal Decomposition

When used for separating multi-component non-stationary signals, the adaptive time-varying filter(ATF) based on multi-scale chirplet sparse signal decomposition(MCSSD) generates phase shift and signal distortion. To overcome this drawback, the zero phase filter is introduced to the mentioned filter, and a fault diagnosis method for speed-changing gearbox is proposed. Firstly, the gear meshing frequency of each gearbox is estimated by chirplet path pursuit. Then, according to the estimated gear meshing frequencies, an adaptive zero phase time-varying filter(AZPTF) is designed to filter the original signal. Finally, the basis for fault diagnosis is acquired by the envelope order analysis to the filtered signal. The signal consisting of two time-varying amplitude modulation and frequency modulation(AM-FM) signals is respectively analyzed by ATF and AZPTF based on MCSSD. The simulation results show the variances between the original signals and the filtered signals yielded by AZPTF based on MCSSD are 13.67 and 41.14, which are far less than variances (323.45 and 482.86) between the original signals and the filtered signals obtained by ATF based on MCSSD. The experiment results on the vibration signals of gearboxes indicate that the vibration signals of the two speed-changing gearboxes installed on one foundation bed can be separated by AZPTF effectively. Based on the demodulation information of the vibration signal of each gearbox, the fault diagnosis can be implemented. Both simulation and experiment examples prove that the proposed filter can extract a mono-component time-varying AM-FM signal from the multi-component time-varying AM-FM signal without distortion.

基于Duffing振子的铁路轨道移频信号测量系统设计

铁路轨道作为移频信号的传输载体,其对于信号对象传输轨迹疏密度的辨别能力,决定了轨道体系对移频信号的测量准确性;为实现对信号对象传输频率的准确辨别,设计基于Duffing振子的铁路轨道移频信号测量系统;将电源模块输出的电量信号,按需分配至STM32F103微处理器、移频信号辨别模块与DSP测量单元之中,完善各级应用部件之间的连接关系,实现铁路轨道移频信号测量系统的硬件方案设计;确定移频信号的Duffing振子描述条件,针对其定义形式,构造移频信号的相空间,完成对铁路轨道移频信号的提取;求解铁路轨道的Lyapunov指数,并构建移频信号的Duffing方程,确定混沌测量参数的取值范围,实现对铁路轨道移频信号的测量,联合各级应用部件,完成基于Duffing振子的铁路轨道移频信号测量系统设计;实验结果表明,上述系统测量所得信号传输轨迹疏密度与真实轨迹疏密度相似度较高,并且测量结果准确率最高值达到了84%左右,说明其能够实现对铁路轨道移频信号的准确测量。