Adaptive Bistable Stochastic Resonance Based Weak Signal Reception in Additive Laplacian Noise

Weak signal reception is a very important and challenging problem for communication systems especially in the presence of non-Gaussian noise,and in which case the performance of optimal linear correlated receiver degrades dramatically.Aiming at this,a novel uncorrelated reception scheme based on adaptive bistable stochastic resonance(ABSR)for a weak signal in additive Laplacian noise is investigated.By analyzing the key issue that the quantitative cooperative resonance matching relationship between the characteristics of the noisy signal and the nonlinear bistable system,an analytical expression of the bistable system parameters is derived.On this basis,by means of bistable system parameters self-adaptive adjustment,the counterintuitive stochastic resonance(SR)phenomenon can be easily generated at which the random noise is changed into a benefit to assist signal transmission.Finally,it is demonstrated that approximately 8dB bit error ratio(BER)performance improvement for the ABSR-based uncorrelated receiver when compared with the traditional uncorrelated receiver at low signal to noise ratio(SNR)conditions varying from-30dB to-5dB.

Acquisition Practice of High Signal-to-Noise Ratio in YTB Block of Sichuan Basin

YTB block in Sichuan basin is a favorable area to exploit oil and gas in shallow tight rock. 3D seismic project of this zone has two characteristics. Firstly, it has high requirements for the tolerance rate of the construction process and the acquisition of high signal-to-noise ratio seismic data;Second, there are widely obstacles and noises that lead to difficult acquisition construction organization. In acquisition practice, high signal-to-noise ratio seismic data was obtained by reasonable design of construction scheme, optimization of excitation parameters, improvement of receiving conditions and optimization of obstacle crossing observation system. .

An algorithm to remove noise from locomotive bearing vibration signal based on self-adaptive EEMD filter

An improved ensemble empirical mode decomposition(EEMD) algorithm is described in this work, in which the sifting and ensemble number are self-adaptive. In particular, the new algorithm can effectively avoid the mode mixing problem. The algorithm has been validated with a simulation signal and locomotive bearing vibration signal. The results show that the proposed self-adaptive EEMD algorithm has a better filtering performance compared with the conventional EEMD. The filter results further show that the feature of the signal can be distinguished clearly with the proposed algorithm, which implies that the fault characteristics of the locomotive bearing can be detected successfully.

Noises and Signal-to-Noise Ratio of Nanosize EIS and ISFET Biosensors

The results of comparative theoretical analyzes of the behavior of internal low-frequency noises, signal-to-noise ratio and sensitivity to DNA molecules for EIS and ISFET based nanosize biosensors are presented. It is shown that EIS biosensor is more sensitive to the presence of DNA molecules in aqueous solution than ISFET sensor. Internal electrical noises level decreases with the increase of concentration of DNA molecules in aqueous solution. In the frequency range 10−3 - 103 Hz noises level for EIS sensor about in three orders is higher than for ISFET sensor. In the other hand, signal-to-noise ratio for capacitive EIS biosensor is much higher than for ISFET sensor.

An Analytical Theory of the Signal-to-Noise Ratio of Hall Plates with Four Contacts and a Single Mirror Symmetry

This work gives an analytical theory of the signal-to-thermal-noise ratio (SNR) of classical Hall plates with four contacts at small magnetic field. In contrast to previous works, the symmetry of the Hall plates is reduced to only a single mirror axis, whereby the average of potentials of the two output contacts off this mirror axis differs from the average of potentials at the two supply contacts on the mirror axis, i.e. the output common mode differs from 50%. Surprisingly, at fixed power dissipated in the Hall plate, the maximum achievable SNR is only 9% smaller for output common modes of 30% and 70% when compared to the overall optimum at output common modes of 50%. The theory is applied to Vertical Hall effect devices with three contacts on the top surface and one contact being the buried layer in a silicon BiCMOS process. Geometries are found with large contacts and only a moderate loss in SNR.

Signal-to-noise ratio of lensless ghost interference with thermal incoherent light

Factors influencing the signal-to-noise ratio (SNR) of lensless ghost interference with thermal incoherent light are investigated.Our result shows that the SNR of lensless ghost interference is related to the transverse length of the object,the position of the object in the imaging system and the transverse size of the light source.Furthermore,the effects of these factors on the SNR are discussed in detail by numerical simulations.

An innovative detection method of high frequency BPSK signal with low signal-to-noise ratio

Based on chaotic oscillator system, this paper proposes a novel method on high frequency low signal-to-noise ratio BPSK(Binary Phase Shift Keying) signal detection. Chaotic oscillator system is a typical non-linear system which is sensitive to periodic signals and immune to noise at the same time. Those properties make it possible to detect low signal-to-noise ratio signals. The BPSK signal is a common signal type which is widely used in modern communication. Starting from the analysis of advantages of chaotic oscillator system and signal features of the BPSK signal, we put forward a unique method that can detect low signal-to-noise ratio BPSK signals with high frequency. The simulation results show that the novel method can detect low signal-to-noise ratio BPSK signals with frequency in an order of magnitude of 108 Hz, and the input Signal-to-Noise Ratio threshold can be -20 dB.

Occurring Mechanism and Restraining Method Research of Numerical Noise Signal in Penetration Simulation

In hard target penetration simulation, the existing researches of the convergence of results are mainly concentrating in the corresponding relationship between penetration depth and mesh scales. However, the influence of the mesh difference on the penetration resistance and acceleration signals are seldom refer to. This paper presents the occurring mechanism and restraining method of numerical noise signal in penetration simulation. First, the concept of the noise signal izs proposed. By taking a 3D penetration simulation as example, the influence of the noise signal on the penetration resistance in different mesh scales and impact velocity is studied. To ensure the convergence of the computational results, the grid scale of the target is encrypted to 1:1:8. In addition, modern spectrum analysis method is introduced to further analyze the penetration resistance signal. The research results presented is useful to improve the computational accuracy of high speed projectile penetration simulation, and provide important reference for carrying out structural design and optimization of fuze system.

Signal-to-noise ratio of Raman signal measured by multichannel detectors

Raman spectroscopy has been widely used to characterize the physical properties of two-dimensional materials(2DMs).The signal-to-noise ratio(SNR or S/N ratio)of Raman signal usually serves as an important indicator to evaluate the instrumental performance rather than Raman intensity itself.Multichannel detectors with outstanding sensitivity,rapid acquisition speed and low noise level have been widely equipped in Raman instruments for the measurement of Raman signal.In this mini-review,we first introduce the recent advances of Raman spectroscopy of 2DMs.Then we take the most commonly used CCD detector and IGA array detector as examples to overview the various noise sources in Raman measurements and analyze their potential influences on SNR of Raman signal in experiments.This overview can contribute to a better understanding on the SNR of Raman signal and the performance of multichannel detector for numerous researchers and instrumental design for industry,as well as offer practical strategies for improving spectral quality in routine measurement.

Enhancement of signal-to-noise ratio of ultracold polar NaCs molecular spectra by phase locking detection

We report a method of high-sensitively detecting the weak signal in photoassociation(PA) spectra of ultracold NaCs molecules by phase sensitive-demodulated trap-loss spectra of Na atoms from a photomultiplier tube. We find that the signal-to-noise ratio(SNR) of the PA spectra is strongly dependent on the integration time and the sensitivity of the lockin amplifier, and our results show reasonable agreement with the theoretical analyses of the SNR with the demodulation parameters. Meanwhile, we investigate the effect of the interaction time of the PA laser with the colliding Na–Cs atom pairs on the SNR of the PA spectra. The atom loss rate is dependent on both the PA-induced atom loss and the loading of the MOT. The high-sensitive detection of the excited ultracold NaCs molecules lays a solid foundation for further study of the formation and application of ultracold NaCs molecules.

Signal-to-noise ratio comparison of angular signal radiography and phase stepping method

Grating-based x-ray phase contrast imaging has the potential to be applied in future medical applications as it is compatible with both laboratory and synchrotron source. However, information retrieval methods are important because acquisition speed, scanning mode, image quality, and radiation dose depend on them. Phase-stepping(PS) is a widely used method to retrieve information, while angular signal radiography(ASR) is a newly established method. In this manuscript,signal-to-noise ratios(SNRs) of ASR are compared with that of PS. Numerical experiments are performed to validate theoretical results. SNRs comparison shows that for refraction and scattering images ASR has higher SNR than PS method,while for absorption image both methods have same SNR. Therefore, our conclusions would have guideline in future preclinical and clinical applications.

A blind source separation algorithm based on negentropy and signal noise ratio

A novel blind source separation (BSS) algorithm based on the combination of negentropy and signal noise ratio (SNR) is presented to solve the deficiency of the traditional independent component analysis (ICA) algorithm after the introduction of the principle and algorithm of ICA. The main formulas in the novel algorithm are elaborated and the idiographic steps of the algorithm are given. Then the computer simulation is used to test the performance of this algorithm. Both the traditional FastICA algorithm and the novel ICA algorithm are applied to separate mixed signal data. Experiment results show the novel method has a better performance in separating signals than the traditional FastICA algorithm based on negentropy. The novel algorithm could estimate the source signals from the mixed signals more precisely.

Local Correlated Noise Improvement of Signal-to-Noise Ratio Gain in an Ensemble of Noisy Neuron

We theoretically investigate the collective response of an ensemble of leaky integrate-and-fire neuron units to a noisy periodic signal by including local spatially correlated noise. By using the linear response theory, we obtained the analytic expression of signal-to-noise ratio (SNR). Numerical simulation results show that the rms amplitude of internal noise can be increased up to?an optimal value where the output SNR reaches a maximum value. Due to the existence of the local spatially correlated noise in the units of the ensemble, the SNR gain of the collective ensemble response can exceed unity and can be optimized when the nearest-neighborhood correlation is negative. This nonlinear collective phenomenon of SNR gain amplification in an ensemble of leaky integrate-and-fire neuron units can be related to the array stochastic resonance (SR) phenomenon. Furthermore, we also show that the SNR gain can also be optimized by tuning the number of neuron units, frequency and?amplitude of the weak periodic signal. The present study illustrates the potential to utilize the local spatially correlation noise and the number of ensemble units for optimizing the collective response of the neuron to inputs, as well as a guidance in the design of information processing devices to weak signal detection.

Study of signal-to-noise ratio driven by colored noise

This paper investigates the signal-to-noise ratio(SNR)driven by colored noise and weak input signals.Based on the Cauchy-Schwarz and Rayleigh quotients inequalities,an analytical expression of SNR is developed,and its upper band is closely related to the Fisher information of noise.For mimicking the colored noise,we adopt the first-order moving-average model and propose the optimal input signal waveform.The stochastic resonance effect in threshold systems is demonstrated for the Gaussian mixture colored noise.The obtained results will be interesting in the case of improving the nonlinear filter performance by adding noise to the weak signal corrupted by the colored noise.

A novel noise reduction technique for underwater acoustic signals based on complete ensemble empirical mode decomposition with adaptive noise,minimum mean square variance criterion and least mean square adaptive filter

Underwater acoustic signal processing is one of the research hotspots in underwater acoustics.Noise reduction of underwater acoustic signals is the key to underwater acoustic signal processing.Owing to the complexity of marine environment and the particularity of underwater acoustic channel,noise reduction of underwater acoustic signals has always been a difficult challenge in the field of underwater acoustic signal processing.In order to solve the dilemma,we proposed a novel noise reduction technique for underwater acoustic signals based on complete ensemble empirical mode decomposition with adaptive noise(CEEMDAN),minimum mean square variance criterion(MMSVC) and least mean square adaptive filter(LMSAF).This noise reduction technique,named CEEMDAN-MMSVC-LMSAF,has three main advantages:(i) as an improved algorithm of empirical mode decomposition(EMD) and ensemble EMD(EEMD),CEEMDAN can better suppress mode mixing,and can avoid selecting the number of decomposition in variational mode decomposition(VMD);(ii) MMSVC can identify noisy intrinsic mode function(IMF),and can avoid selecting thresholds of different permutation entropies;(iii) for noise reduction of noisy IMFs,LMSAF overcomes the selection of deco mposition number and basis function for wavelet noise reduction.Firstly,CEEMDAN decomposes the original signal into IMFs,which can be divided into noisy IMFs and real IMFs.Then,MMSVC and LMSAF are used to detect identify noisy IMFs and remove noise components from noisy IMFs.Finally,both denoised noisy IMFs and real IMFs are reconstructed and the final denoised signal is obtained.Compared with other noise reduction techniques,the validity of CEEMDAN-MMSVC-LMSAF can be proved by the analysis of simulation signals and real underwater acoustic signals,which has the better noise reduction effect and has practical application value.CEEMDAN-MMSVC-LMSAF also provides a reliable basis for the detection,feature extraction,classification and recognition of underwater acoustic signals.

Analysis of EMD Algorithm for Identification and Extraction of An Acoustic Signal in Underwater Channel Against Wind Driven Ambient Noise

Sonar generated acoustic signals transmitted in underwater channel for distant communications are affected by numerous factors like ambient noise, making them nonlinear and non-stationary in nature. In recent years, the application of Empirical Mode Decomposition(EMD) technique to analyze nonlinear and non-stationary signals has gained much attention. It is an empirical approach to decompose a signal into a set of oscillatory modes known as intrinsic mode functions(IMFs). In general, Hilbert transform is used in EMD for the identification of oscillatory signals. In this paper a new EMD algorithm is proposed using FFT to identify and extract the acoustic signals available in the underwater channel that are corrupted due to various ambient noises over a range of 100 Hz to 10 kHz in a shallow water region. Data for analysis are collected at a depth of 5 m and 10 m offshore Chennai at the Bay of Bengal. The algorithm is validated for different sets of known and unknown reference signals. It is observed that the proposed EMD algorithm identifies and extracts the reference signals against various ambient noises. Significant SNR improvement is also achieved for underwater acoustic signals.

Noise cancellation of a multi-reference full-wave magnetic resonance sounding signal based on a modified sigmoid variable step size least mean square algorithm

Nano-volt magnetic resonance sounding(MRS) signals are sufficiently weak so that during the actual measurement, they are affected by environmental electromagnetic noise, leading to inaccuracy of the extracted characteristic parameters and hindering effective inverse interpretation. Considering the complexity and non-homogeneous spatial distribution of environmental noise and based on the theory of adaptive noise cancellation, a model system for noise cancellation using multi-reference coils was constructed to receive MRS signals. The feasibility of this system with theoretical calculation and experiments was analyzed and a modified sigmoid variable step size least mean square(SVSLMS) algorithm for noise cancellation was presented. The simulation results show that, the multi-reference coil method performs better than the single one on both signal-to-noise ratio(SNR) improvement and signal waveform optimization after filtering, under the condition of different noise correlations in the reference coils and primary detecting coils and different SNRs. In particular, when the noise correlation is poor and the SNR<0, the SNR can be improved by more than 8 dB after filtering with multi-reference coils. And the average fitting errors for initial amplitude and relaxation time are within 5%. Compared with the normalized least mean square(NLMS) algorithm and multichannel Wiener filter and processing field test data, the effectiveness of the proposed method is verified.

Extraction of Signals Buried in Noise: Non-Ergodic Processes

In this paper, we propose extraction of signals buried in non-ergodic processes. It is shown that the proposed method extracts signals defined in a non-ergodic framework without averaging or smoothing in the direct time or frequency domain. Extraction is achieved independently of the nature of noise, correlated or not with the signal, colored or white, Gaussian or not, and locations of its spectral extent. Performances of the pro-posed extraction method and comparative results with other methods are demonstrated via experimental Doppler velocimetry measurements.

Extraction of Buried Signals in Noise: Correlated Processes

In this paper, we propose extraction of signals correlated with noise in which they are buried. Proposed extraction method uses no a-priori information on the buried signal and works independently of the nature of noise, correlated or not with the signal, colored or white, Gaussian or not, and locations of its spectral extent. Extraction of buried correlated signals is achieved without averaging in the time or frequency domain.

Stochastic Resonance in a Single-Mode Laser Driven by Quadratic Colored Pump Noise:Effects of Biased Amplitude Modulation Signal

A single-mode laser noise model driven by quadratic colored pump noise and biased amplitude modulationsignal is proposed.The analytic expression of signal-to-noise ratio is calculated by using a new linearized procedure.Itis found that there are three different typies of stochastic resonance in the model:the conventional form of stochasticresonance,the stochastic resonance in the broad sense,and the bona fide SR.