In order to improve the service performance and explore the damage mechanism of silicon carbide-mullite bricks for the transition zone of cement rotary kilns,the phase composition and the microstructure of a used bric...In order to improve the service performance and explore the damage mechanism of silicon carbide-mullite bricks for the transition zone of cement rotary kilns,the phase composition and the microstructure of a used brick in the transition zone of a cement rotary kiln were analyzed by XRD,SEM and EDS.The results show that the liquid and alkali vapor phases generated by the reaction between cement materials and the silicon carbide-mullite brick mostly enter the silicon carbide-mullite brick through the pores;meanwhile,Ca+and K+in the cement penetrate through the liquid maintaining a high chemical potential energy to dissolve Al2O3 and SiO2 at the top of the liquid phase thus enhancing the phase penetration;with the decreasing temperature,crystals such as gehlenite,potassium feldspar and potassium chloride are precipitated,which destroy the original structure and increase the difference of thermal expansion coefficient between the high temperature dense end and the metamorphic layer thus resulting in cracks,spalling,and rupture.展开更多
1 Scope This standard specifies the definition, classifica- tion, technical requirements, test methods, quality appraisal procedures, packing, marking, transportation, storage, and quality certificate of silicon nitri...1 Scope This standard specifies the definition, classifica- tion, technical requirements, test methods, quality appraisal procedures, packing, marking, transportation, storage, and quality certificate of silicon nitride bonded silicon carbide bricks.展开更多
SiC- mullite brick is widely used in the upper and lower transitional zones of cement rotary kilns, due to excellent thermal shock resistance, and abrasion resist- ance. The investigation of different bauxites was mad...SiC- mullite brick is widely used in the upper and lower transitional zones of cement rotary kilns, due to excellent thermal shock resistance, and abrasion resist- ance. The investigation of different bauxites was made on the performance and micro-structure of SiC - mullite brick, especially thermal shock resistance. In two batches of bricks （ G1 and G2 ） , and two grades of bauxites （ L1 and I_2 ）, samples＇ physical and chemical properties were tested, and microstructure and phase composition were studied by SEM and XRD. The results show that raw material I2, containing large numbers of micro- pores smaller than 4 μm, has well developed mullite phase. While using L2 as aggregates and flues, SiC- mullite brick G2 has excellent thermal shock resistance. Therefore, for manufacture of SiC - mullite brick, not only chemical composition, bulk density and open porosi- ty of bauxite are important, but also its microstructure has to be considered, such as phase composition, crystal size and pore size distribution.展开更多
Hot metal transfer ladles were historically lined with high alumina refractories because of compatibility of high alumina refractories with the highly acidic slag, which is transferred .from the iron making plant alon...Hot metal transfer ladles were historically lined with high alumina refractories because of compatibility of high alumina refractories with the highly acidic slag, which is transferred .from the iron making plant along with hot metal. With the introduction of higher capacity ladles, technological advancement in the process and increased productivity, calls for a higher campaign life of hot metal ladles, which could not be performed by ordinary high alumina refractories. Resin bonded Al2O3- SiC-C （hereinafter ASC ） bricks gradually developed which at present taking place replacing the conventional refractories. Considerable work has been carried out in developing the ASC refractory to reach the present state. However, for higher capacity ladles still there is a lot of scope for improvement. The present paper deals with the newly developed ASC bricks, which was used in 165 ton capacity hot metal ladles in one European plant and has given a substantial increase in performance. But, the customer was not fuUy satisfied since the brick was reported to produce smokes during preheating of the ladle. In the subsequent supply the smoke generation problem was taken care by adjusting the binders and additives and eco-friendly bricks were re-engineered and supplied to the same plant, which also performed splendidly and created all time record in their plant history.展开更多
Al2O3-SiC-C specimens were prepared using white fused corundum （3-1,≤1 and ≤0.044 mm）,Al2O3-SiC composite powders （d50 ≤ 5 μm）,α-Al2O3 micropowder （d50 =1.2 μm）,SiC powder （≤ 0.044 mm）,flake graphite （...Al2O3-SiC-C specimens were prepared using white fused corundum （3-1,≤1 and ≤0.044 mm）,Al2O3-SiC composite powders （d50 ≤ 5 μm）,α-Al2O3 micropowder （d50 =1.2 μm）,SiC powder （≤ 0.044 mm）,flake graphite （≤ 0.088 mm）,Si powder （d50 =42.8 μm） and B4C powder （d50 ≤10 μm） as main starting materials,and thermosetting phenolic resin as binder.4%,8%,12% and 16% （in mass,the same hereinafter） of Al2O3-SiC composite powders substituted the same quantity of α-Al2O3 micropowder ＋ SiC powder.Effects of composite powder additions on apparent porosity,bulk density,cold modulus of rupture,cold crushing strength,hot modulus of rupture （1 400 ℃）,thermal shock resistance （1 100 ℃,water quenching） and oxidation resistance （1 000 and 1 500 ℃） of Al2O3-SiC -C specimens after 180 ℃ curing,1 000 ℃ 3 h carbon-embedded firing and 1 500 ℃ 3 h carbon-embedded firing,respectively,were researched.The results indicate that：（1） with the increase of Al2O3-SiC composite powder,cold strengths of the cured specimens decline,those of the specimens fired at 1 000 ℃ change a little,and those of the specimens fired at 1 500 ℃ change a little except for an obvious improvement of cold crushing strength ; （2） with the increase of Al2O3-SiC composite powder,hot modulus of rupture at 1 400 ℃ decreases and thermal shock resistance enhances significantly; （3） when Al2O3-SiC composite powder addition is 4%,the oxidation resistance at 1 500 ℃ is the best,and the reason may be the composite powder is finer and more active,which is beneficial to form dense mullite protective layer to retard the O2 diffusion into the specimens.展开更多
Low-carbon MgO - C specimens with dimension of Ф6 mm × 36 mm were prepared using fused magnesia, flake graphite and carbon black as main starting materials, thermoplastic phenolic resin as binder, hexamethyl ene...Low-carbon MgO - C specimens with dimension of Ф6 mm × 36 mm were prepared using fused magnesia, flake graphite and carbon black as main starting materials, thermoplastic phenolic resin as binder, hexamethyl ene tetramine as curing agent, Si powder （ w （Si） 〉 80%, particle size 〈0. 074 mm） and B℃ （ d90 =36. 5 μm ） as antioxidant, pressing under 200 MPa and drying at 200 ℃ for 24 h. The oxidation resistance tests were conducted at 600 ℃ , 1 000 ℃ and 1 400 ℃ for 2 h, respectively. Effects of B4C and Si antioxidant on oxidation resistance of low-carbon MgO - C brick were studied by comparing the areas of the decarburized layers. The results shaw that： （1） When Si powder addition is 3%, at 600 ℃ and 1 000 ℃, the specimens with 0. 5% B4C perform good oxidation resistance; at 1 400 ℃, the oxidation resistance of the specimens is improved with the addition of B4C increasing, and that of the specimen with 0. 7% B4 C is the best. （2） When B4C addition is 0. 5%, at 600 ℃ and 1 000 ℃ ,the oxidation resistances of the specimens with 3% and 5% Si powder are similar, which are better than that of the specimen with 1% Si powder; and at 1 400 ℃ , the oxidation resistance of the specimens is improved obviously with the addition of Si powder increasing, and that of the specimen with 5% Si powder is the best. （3） Bused on the results, it is believed that the low-carbon MgO - C brick with 0. 5% B4C and 3% Si powder performs the best oxidation resistance.展开更多
文摘In order to improve the service performance and explore the damage mechanism of silicon carbide-mullite bricks for the transition zone of cement rotary kilns,the phase composition and the microstructure of a used brick in the transition zone of a cement rotary kiln were analyzed by XRD,SEM and EDS.The results show that the liquid and alkali vapor phases generated by the reaction between cement materials and the silicon carbide-mullite brick mostly enter the silicon carbide-mullite brick through the pores;meanwhile,Ca+and K+in the cement penetrate through the liquid maintaining a high chemical potential energy to dissolve Al2O3 and SiO2 at the top of the liquid phase thus enhancing the phase penetration;with the decreasing temperature,crystals such as gehlenite,potassium feldspar and potassium chloride are precipitated,which destroy the original structure and increase the difference of thermal expansion coefficient between the high temperature dense end and the metamorphic layer thus resulting in cracks,spalling,and rupture.
文摘1 Scope This standard specifies the definition, classifica- tion, technical requirements, test methods, quality appraisal procedures, packing, marking, transportation, storage, and quality certificate of silicon nitride bonded silicon carbide bricks.
文摘SiC- mullite brick is widely used in the upper and lower transitional zones of cement rotary kilns, due to excellent thermal shock resistance, and abrasion resist- ance. The investigation of different bauxites was made on the performance and micro-structure of SiC - mullite brick, especially thermal shock resistance. In two batches of bricks （ G1 and G2 ） , and two grades of bauxites （ L1 and I_2 ）, samples＇ physical and chemical properties were tested, and microstructure and phase composition were studied by SEM and XRD. The results show that raw material I2, containing large numbers of micro- pores smaller than 4 μm, has well developed mullite phase. While using L2 as aggregates and flues, SiC- mullite brick G2 has excellent thermal shock resistance. Therefore, for manufacture of SiC - mullite brick, not only chemical composition, bulk density and open porosi- ty of bauxite are important, but also its microstructure has to be considered, such as phase composition, crystal size and pore size distribution.
文摘Hot metal transfer ladles were historically lined with high alumina refractories because of compatibility of high alumina refractories with the highly acidic slag, which is transferred .from the iron making plant along with hot metal. With the introduction of higher capacity ladles, technological advancement in the process and increased productivity, calls for a higher campaign life of hot metal ladles, which could not be performed by ordinary high alumina refractories. Resin bonded Al2O3- SiC-C （hereinafter ASC ） bricks gradually developed which at present taking place replacing the conventional refractories. Considerable work has been carried out in developing the ASC refractory to reach the present state. However, for higher capacity ladles still there is a lot of scope for improvement. The present paper deals with the newly developed ASC bricks, which was used in 165 ton capacity hot metal ladles in one European plant and has given a substantial increase in performance. But, the customer was not fuUy satisfied since the brick was reported to produce smokes during preheating of the ladle. In the subsequent supply the smoke generation problem was taken care by adjusting the binders and additives and eco-friendly bricks were re-engineered and supplied to the same plant, which also performed splendidly and created all time record in their plant history.
文摘Al2O3-SiC-C specimens were prepared using white fused corundum （3-1,≤1 and ≤0.044 mm）,Al2O3-SiC composite powders （d50 ≤ 5 μm）,α-Al2O3 micropowder （d50 =1.2 μm）,SiC powder （≤ 0.044 mm）,flake graphite （≤ 0.088 mm）,Si powder （d50 =42.8 μm） and B4C powder （d50 ≤10 μm） as main starting materials,and thermosetting phenolic resin as binder.4%,8%,12% and 16% （in mass,the same hereinafter） of Al2O3-SiC composite powders substituted the same quantity of α-Al2O3 micropowder ＋ SiC powder.Effects of composite powder additions on apparent porosity,bulk density,cold modulus of rupture,cold crushing strength,hot modulus of rupture （1 400 ℃）,thermal shock resistance （1 100 ℃,water quenching） and oxidation resistance （1 000 and 1 500 ℃） of Al2O3-SiC -C specimens after 180 ℃ curing,1 000 ℃ 3 h carbon-embedded firing and 1 500 ℃ 3 h carbon-embedded firing,respectively,were researched.The results indicate that：（1） with the increase of Al2O3-SiC composite powder,cold strengths of the cured specimens decline,those of the specimens fired at 1 000 ℃ change a little,and those of the specimens fired at 1 500 ℃ change a little except for an obvious improvement of cold crushing strength ; （2） with the increase of Al2O3-SiC composite powder,hot modulus of rupture at 1 400 ℃ decreases and thermal shock resistance enhances significantly; （3） when Al2O3-SiC composite powder addition is 4%,the oxidation resistance at 1 500 ℃ is the best,and the reason may be the composite powder is finer and more active,which is beneficial to form dense mullite protective layer to retard the O2 diffusion into the specimens.
文摘Low-carbon MgO - C specimens with dimension of Ф6 mm × 36 mm were prepared using fused magnesia, flake graphite and carbon black as main starting materials, thermoplastic phenolic resin as binder, hexamethyl ene tetramine as curing agent, Si powder （ w （Si） 〉 80%, particle size 〈0. 074 mm） and B℃ （ d90 =36. 5 μm ） as antioxidant, pressing under 200 MPa and drying at 200 ℃ for 24 h. The oxidation resistance tests were conducted at 600 ℃ , 1 000 ℃ and 1 400 ℃ for 2 h, respectively. Effects of B4C and Si antioxidant on oxidation resistance of low-carbon MgO - C brick were studied by comparing the areas of the decarburized layers. The results shaw that： （1） When Si powder addition is 3%, at 600 ℃ and 1 000 ℃, the specimens with 0. 5% B4C perform good oxidation resistance; at 1 400 ℃, the oxidation resistance of the specimens is improved with the addition of B4C increasing, and that of the specimen with 0. 7% B4 C is the best. （2） When B4C addition is 0. 5%, at 600 ℃ and 1 000 ℃ ,the oxidation resistances of the specimens with 3% and 5% Si powder are similar, which are better than that of the specimen with 1% Si powder; and at 1 400 ℃ , the oxidation resistance of the specimens is improved obviously with the addition of Si powder increasing, and that of the specimen with 5% Si powder is the best. （3） Bused on the results, it is believed that the low-carbon MgO - C brick with 0. 5% B4C and 3% Si powder performs the best oxidation resistance.
