Microstructure and mechanical properties characterization of AA6061/TiC aluminum matrix composites synthesized by in situ reaction of silicon carbide and potassium fluotitanate

Aluminum alloys AA6061 reinforced with various amounts （0, 2.5% and 5%, mass fraction） of TiC particles were synthesized by the in situ reaction of inorganic salt K2TiF6 and ceramic particle SiC with molten aluminum. The casting was carried out at an elevated temperature and held for a longer duration to decompose SiC to release carbon atoms. X-ray diffraction patterns of the prepared AMCs clearly revealed the formation of TiC particles without the occurrence of any other intermetallic compounds. The microstructure of the prepared AA6061/TiC AMCs was studied using field emission scanning electron microscope （FESEM） and electron backscatter diffraction （EBSD）. The in situ formed TiC particles were characterized with homogeneous distribution, clear interface, good bonding and various shapes such as cubic, spherical and hexagonal. EBSD maps showed the grain refinement action of TiC particles on the produced composites. The formation of TiC particles boosted the microhardness and ultimate tensile strength （UTS） of the AMCs.

Study on Processing Conditions of Aluminum Matrix Composites Reinforced with Boron Carbide Particles

Different pre-heating of boron carbide particles for reinforcement and different processing conditions were studied in this work. Being one of the most cost-effective industrial methods, conventional melt stir-casting route was utilized.Result showed that the boron carbide particles distributed well for a suitable pre-heating temperature and processed in air.No reaction product was found at the A1-B4C interfaces at the resolution limit of SEM used in that way.

Microstructure,mechanical and wear properties of aluminum borate whisker reinforced aluminum matrix composites

The microstructural features and the consequent mechanical properties were characterized in aluminium borate whisker(ABOw)(5, 10 and 15 wt.%) reinforced commercially-pure aluminium composites fabricated by conventional powder metallurgy technique. The aluminium powder and the whisker were effectively blended by a semi-powder metallurgy method. The blended powder mixtures were cold compacted and sintered at 600 ℃. The sintered composites were characterized for microstructural features by optical microscopy(OM), scanning electron microscopy(SEM), energy dispersive spectroscopy(EDS), transmission electron microscopy(TEM) and X-ray diffraction(XRD) analysis. Porosity in the composites with variation in ABOw contents was determined. The effect of variation in content of ABOw on mechanical properties, viz. hardness, bending strength and compressive strength of the composites was evaluated. The dry sliding wear behaviour was evaluated at varying sliding distance at constant loads. Maximum flexural strength of 172 MPa and compressive strength of 324 MPa with improved hardness around HV 40.2 are obtained in composite with 10 wt.% ABOw. Further increase in ABOw content deteriorates the properties. A substantial increase in wear resistance is also observed with 10 wt.% ABOw. The excellent combination of mechanical properties of Al-10 wt.%ABOw composites is attributed to good interfacial bonds, less porosity and uniformity in the microstructure.

Diffusion Bonding of Silicon Carbide Particulate Reinforced 2024 Al Composites

A study has been made on diffusion bonding of SiCp/2024Ai composites by means of pure Al interlayer. In the condition of TB=843 K, PB=16 MPa, tB= 60 min, the diffusion bonded joint, with a shear strength of 235 MPa, was obtained when a 15 μm thick interlayer was used. The results of the shear testing and SEM indicate that fracture of the joint presented characteristics of ductile rupture.

Microstructure and Strength of Laser Welds of Sub-micron Particulate-reinforced Aluminum Matrix Composite Al_2O_(3p)/6061Al

The microstructure of laser welds of sub-micron particulate-reinforced aluminum matrix composite Al_2O_(3p)/6061Al and the weldability of the material were studied. Experimental results indicated that because of the huge specific surface area of the reinforcement, the interfacial reaction between the matrix and the reinforcement was re- strained intenslvely at elevated temperature and pulsed laser beam. The main factor affecting the weldability of the com- posite was the reinforcement segregation in the weld resulting from the push of the liquid/solid interface during the soli- dification of the molten pool. The laser pulse frequency directly affected the reinforcement segregation and the reinfor- cement distribution in the weld, so that the weldability of the composite could be improved by increasing the laser pulse frequency. On the basis of this, a satisfactory welded joint of sub-micron paniculate-reinforced aluminum matrix com- posite Al_2O_(3p)/6061Al was obtained by using appopriate welding parameters.

Machining studies of die cast aluminum alloy-silicon carbide composites

Metal matrix composites （MMCs） with high specific stiffness, high strength, improved wear resistance, and thermal properties are being increasingly used in advanced structural, aerospace, automotive, electronics, and wear applications. Aluminum alloy-silicon carbide composites were developed using a new combination of the vortex method and the pressure die-casting technique in the present work. Machining studies were conducted on the aluminum alloy-silicon carbide （SiC） composite work pieces using high speed steel （HSS） end-mill tools in a milling machine at different speeds and feeds. The quantitative studies on the machined work piece show that the surface finish is better for higher speeds and lower feeds. The surface roughness of the plain aluminum alloy is better than that of the aluminum alloy-silicon carbide composites. The studies on tool wear show that flank wear increases with speed and feed. The end-mill tool wear is higher on machining the aluminum alloy-silicon carbide composites than on machining the plain aluminum alloy.

Tailoring microstructure and mechanical properties of aluminum matrix composites reinforced with novel Al/CuFe multi-layered core-shell particles

Aluminum matrix composites(AMCs), reinforced with novel pre-synthesized Al/Cu Fe multi-layered coreshell particles, were fabricated by different consolidation techniques to investigate their effect on microstructure and mechanical properties. To synthesize multi-layered Al/Cu Fe core-shell particles, Cu and Fe layers were deposited on Al powder particles by galvanic replacement and electroless plating method, respectively. The core-shell powder and sintered compacts were characterized by using X-ray diffraction(XRD), scanning electron microscopy(SEM) equipped with energy dispersive spectroscopy(EDX), pycnometer, microhardness and compression tests. The results revealed that a higher extent of interfacial reactions, due to the transformation of the deposited layer into intermetallic phases in spark plasma sintered composite, resulted in high relative density(99.26%), microhardness(165 HV0.3) and strength(572 MPa). Further, the presence of un-transformed Cu in the shell structure of hot-pressed composite resulted in the highest fracture strain(20.4%). The obtained results provide stronger implications for tailoring the microstructure of AMCs through selecting appropriate sintering paths to control mechanical properties.

Fabrication and densification enhancement of SiC-particulate-reinforced copper matrix composites prepared via the sinter-forging process

The fabrication of copper （Cu） and copper matrix silicon carbide （Cu/SiCp） particulate composites via the sinter-forging process was investigated. Sintering and sinter-forging processes were performed under an inert Ar atmosphere. The influence of sinter-forging time, temperature, and compressive stress on the relative density and hardness of the prepared samples was systematically investigated and subsequently compared with that of the samples prepared by the conventional sintering process. The relative density and hardness of the composites were enhanced when they were prepared by the sinter-forging process. The relative density values of all Cu/SiCp composite samples were observed to decrease with the increase in SiC content.

Exploration of Al-based matrix composites reinforced by hierarchically spherical agents

Al-based composites reinforced with A1-Ti intermetallic compounds/Ti metal hierarchically spherical agents were successfully fabricated by powder metallurgy. This kind of structure produces strongly bonded interfaces as well as soft/hard/soft transition regions between the matrix and reinforced agents, which are beneficial to load transfer during deformation. As expected, the resultant composites exhibit promising mechanical properties at ambient temperature. The underlying mechanism was also discussed in this paper.

Pseudo-in-situ stir casting: a new method for production of aluminum matrix composites with bimodal-sized B_4C reinforcement

A new method was applied to produce an Al-0.5wt%Ti-0.3wt%Zr/5vol%B_4C composite via stir casting with the aim of characterizing the microstructure of the resulting composite. For the production of the composite, large B4 C particles（larger than 75 μm） with no pre-heating were added to the stirred melt. Reflected-light microscopy, X-ray diffraction, scanning electron microscopy, field-emission scanning electron microscopy, laser particle size analysis, and image analysis using the Clemex software were performed on the cast samples for microstructural analysis and phase detection. The results revealed that as a consequence of thermal shock, B_4 C particle breakage occurred in the melt. The mechanism proposed for this phenomenon is that the exerted thermal shock in combination with the low thermal shock resistance of B_4 C and large size of the added B_4 C particles were the three key parameters responsible for B_4 C particle breakage. This breakage introduced small particles with sizes less than 10 μm and with no contamination on their surfaces into the melt. The mean particle distance measured via image analysis was approximately 60 μm. The coefficient of variation index, which was used as a measure of particle distribution homogeneity, showed some variations, indicating a relatively homogeneous distribution.

Effect of Silicon Carbide and Titanium Hydride on the Foamability of Aluminum Alloy (6061)

Aluminum foam is a light weight material with good mechanical and energy absorption properties. In this study, aluminum foam composite was fabricated using aluminum powder 6061 and silicon carbide (SiC) powder. Titanium hydride (TiH2) was used as the foaming agent. Cold compact followed by hot pressing (sintering) was used to produce the composite precursor. Foaming was carried out, following the sintering process, by heating the aluminum composite precursor to a temperature above the melting point of aluminum (Al). The linear expansion of the foam and the percent porosity were found to increase as the SiC percentage decreased from 10 to 4%, whereas the density got lower. The percent porosity and linear expansion were both found to increase as the percentage of the foaming agent was increased from 0.5 to 1.5%. Compression stress was evaluated for two different porosity values (40% and 47%), and found to be higher for the samples with lower percent porosity at the same strain value. Effect of shape memory alloy fiber, made of nickel and titanium (NiTi), on the mechanical properties was also investigated. The compression stress was higher, in the densification region, for the samples in which NiTi was used.

Pulse-Impact on Microstructure of Liquid-Phase-Pulse-Impact Diffusion Welded Joints of Particle Reinforcement Aluminum Matrix Composites at Various Temperatures

Investigation was to study the influence of pulse-impact on microstructure of Liquid-Phase-Pulse-Impact Diffusion Welding (LPPIDW) welded joints of aluminum matrix composite SiCp/A356, SiCp/6061Al, Al2O3p/6061Al. Results showed that under the effect of pulse-impact: 1) the interface state between reinforcement particle (SiC, Al2O3) and matrix was prominently;2) the initial pernicious contact-state of reinforcement particles was changed from reinforcement (SiC, Al2O3)/reinforcement (SiC, Al2O3) to reinforcement (SiC, Al2O3)/matrix/ reinforcement (SiC, Al2O3);3) the density of dislocation in the matrix neighboring to and away from the interface in the matrix was higher than its parent composite;and 4) the intensively mutual entwisting of dislocation was occurred. Studies illustrated that: 1) deformation was mainly occurred in the matrix grain;and 2) under the effect of pulse-impact, the matrices around reinforcement (SiC, Al2O3) particles engendered intensive aberration offered a high density nucleus area for matrix crystal, which was in favor of forming nano-grains and improved the properties of the successfully welded composite joints.

Processing of nanostructured metallic matrix composites by a modified accumulative roll bonding method with structural and mechanical considerations

Particulate reinforced metallic matrix composites have attracted considerable attention due to their lightweight, high strength, high specific modulus, and good wear resistance. A1/B4C composite strips were produced in this work by a modified accumulative roll bonding process where the strips were rotated 90° around the normal direction between successive passes. Transmission electron microscopy and X-ray diffraction analyses reveal the development of nanostructures in the Al matrix after seven passes. It is found that the B4C reinforcement distribution in the matrix is improved by progression of the process. Additionally, the tensile yield strength and elongation of the processed materials are increased with the increase of passes.

INVESTIGATION ON THE FORMATION MECHANISM OF TITANIUM CARBIDE PREPARED BY IN SITU REACTION IN MOLTEN ALUMINUM

A novel technique in which TiC particulate are prepared by an in situ reaction in molten aluminum was introduced for producing TiC/Al composite. In order to reveal the characteristics of the technique, the formation mechanism of TiC particulate prepared by this method was studied. Both theoretical and experimental results show that the TiC particulate is formed by a diffusion mechanism when the molar fraction of aluminum in the preforms is higher than 20.02%. On the contrary, the TiC particulate is formed by a solution-precipitation mechanism when the fraction of aluminum in the preforms is lower than 20.02%.

Improvement of SiC_p Reinforced Cast AluminiumComposites by the ROC Method

The process of rapid omnidirectional compaction (ROC) of SiCp/cast Al composites was investigated. An apparatus for ROC process was established. Full compactibility of various SiCp/cast Al composites was accomplished. Defects in the materials were eliminated. It is found that after ROC, the tensile strength of the 30% SiCp/Z1109 composite increased by 35%. It is demonstrated that the ROC process is an effective method for improving the performance of SiCp/Al composites.

CRYOGENIC PROPERTIES OF AI-SiC COMPOSITES AND EFFECT OF MATRIX CHARACTERISTICS AND REINFORCEMENT TYPE

The tensile tests on the silicon carbide whisker and paniculate reinforced 2124A1 and 2024Al alloy composites fabricated by P/ M technique were carried out at the temperatures ranging from room temperature to - 196C . and the fracture surfaces were examined. The cryogenic strength of the composites increases with the decreasing test temperature. Clean interface is beneficial to the improvement in cryogenic strength of the composites. The effect of the interface characteristics on the paniculate composite is less than that on the whisker composite. With the decreasing temperature, the increase in strength of the whisker composite is more than that of the paniculate composite, which could be attributed to different strengthening mechanism.

Preparation and Characterization of Aluminium Wire Mat Reinforced Polyester Composite

Aluminum wire mat reinforced polyester composite has been studied as an al-ternative structural material. The physical and mechanical properties of the composite such as tensile strength, flexural strength, water absorption, hardness illustrated the competency of the developed composite. It was found that per-cent water absorption is very low for the resultant studied composite. However, water absorption increased very slowly when metal mat layers were increased. Furthermore, mechanical strength of the composite was increased as mechanical properties: tensile strength, flexural strength, hardness and stiffness of this composite increased with the increase in the number of metal mat layer in the composite. This study suggested the use of this composite as an unbeaten al-ternative structural material to conventional materials.

Fabrication and Characterization of Glass Fiber with SiC Reinforced Polymer Composites

Glass Fiber Reinforced Polymeric (GFRP) Composites are most commonly used as bumpers for vehicles, electrical equipment panels, and medical devices enclosures. These materials are also widely used for structural applications in aerospace, automotive, and in providing alternatives to traditional metallic materials. The paper fabricated epoxy and polyester resin composites by using silicon carbide in various proportions along with GFRP. The hand lay-up technique was used to fabricate the laminates. To determine the properties of fabricated composites, the tensile, impact, and flexural tests were conducted. This method of fabrication was very simple and cost-effective. Their mechanical properties like yield strength, yield strain, Young’s modulus, flexural modulus, and impact energy were investigated. The mechanical properties of the GFRP composites were also compared with the fiber volume fraction. The fiber volume fraction plays a major role in the mechanical properties of GFRP composites. Young’s modulus and tensile strength of fabricated composites were modelled and compared with measured values. The results show that composites with epoxy resin demonstrate higher strength and modulus compared to composites with polyester resin.

增强体表面改性在高导热金属基复合材料中的应用

随着电子技术的高速发展和电子器件的更新换代,电子封装材料的性能需求越来越高。金属基复合材料,尤其是铝基和铜基复合材料具有高导热、低膨胀、高稳定性等特点,是具有广阔应用前景的电子封装材料。然而,金刚石、石墨烯、硅等增强体与基体的润湿性差,或者在高温下与基体发生有害的界面反应,限制了此类高导热金属基复合材料的开发和应用。本文简述了金属基复合材料的界面研究进展,结合影响金属基复合材料界面结合的因素,提出了几种改善界面结合的方法。增强体表面改性是改善金属基复合材料界面的重要途径之一,常用工艺有磁控溅射法、化学气相沉积法、溶胶凝胶法、化学镀法等;最后,对增强体表面改性在高热导金属基复合材料中的应用进行分析和展望。

铝酸盐体系中氧化时间对碳化硅颗粒增强铝基复合材料微弧氧化膜层的影响

[目的]探究氧化时间对碳化硅颗粒增强铝基(SiC_(p)/Al)复合材料微弧氧化膜层的影响。[方法]选用铝酸盐体系作为电解液,对SiC_(p)/Al复合材料进行微弧氧化处理,分析氧化时间对膜层组织结构、物相、厚度、粗糙度、结合力、电绝缘性及耐蚀性的影响。[结果]随着氧化时间延长,膜层逐渐变得连续均匀,厚度增加。若氧化时间过长,膜层会出现层叠现象,形成大尺寸微孔及裂纹,且生长速率越来越低。膜层结合力随氧化时间延长先增大后减小,在60 min时最大,达到39.85 N。氧化时间为10 min时,膜层的电绝缘性及耐蚀性最优,100 V和500 V电压下的绝缘电阻分别达到3.11×10^(12)Ω和1.41×10^(12)Ω,腐蚀电位为-0.6298 V,腐蚀电流密度为1.332×10^(-7)A/cm^(2)。[结论]SiC_(p)/Al复合材料表面微弧氧化膜层的连续性、均匀性及生长速率均与氧化时间有关。需选择合适的氧化时间,才能制备出连续、均匀且综合性能优异的膜层。