Si3N4-Si2N2O composites were fabricated with amorphous nano-sized silicon nitride powders by the liquid phase sintering （ LPS ）. The Si2 N2O phase was generated by an in-situ reaction 2 Si3 N4 （ s ） ＋ 1.5 02 （ g...Si3N4-Si2N2O composites were fabricated with amorphous nano-sized silicon nitride powders by the liquid phase sintering （ LPS ）. The Si2 N2O phase was generated by an in-situ reaction 2 Si3 N4 （ s ） ＋ 1.5 02 （ g ） = 3 Si2 N2O （ s ） ＋ N2 （ g ） . The content of Si2 N2 O phase up to 60% in the volume was obtained at a sintering temperature of 1 650℃ and reduced when the sintering temperature increased or decreased, indicating the reaction is reversible. The mass loss, relative density and average grain size increased with increasing the sintering temperature. The average grain size was less than 500 nm when the sintering temperature was below 1 700 ℃. The sintering procedure contains a complex crystallization and a phase transition ： amorphous silicon nitride→equiaxial α- Si3 N4→ equiaxial β- Si3 N4→ rod- like Si2 N2O→ needle- like β- Si3N4 . Small round-shaped β→ Si3 N4 particles were entrapped in the Si2 N2O grains and a high density of staking faults was situated in the middle of Si2 N2O grains at a sintering temperature of 1 650 ℃. The toughness inereased from 3.5 MPa·m^1/2 at 1 600 ℃ to 7.2 MPa· m^1/2 at 1 800 ℃ . The hardness was as high as 21.5 GPa （Vickers） at 1 600 ℃ .展开更多
Silicon (Si) is a promising anode material for next-generation high-energy lithium-ion batteries (LIBs) due to its high capacity.However,the large volumetric expansion,poor ion conductivity and unstable solid electrol...Silicon (Si) is a promising anode material for next-generation high-energy lithium-ion batteries (LIBs) due to its high capacity.However,the large volumetric expansion,poor ion conductivity and unstable solid electrolyte interface (SEI) lead to rapid capacity fading and low rate performance.Herein,we report Si nitride (SiN) comprising stoichiometric Si_(3)N_(4) and Li-active anazotic SiN_(x) coated porous Si (p-Si@SiN)for high-performance anodes in LIBs.The ant-nest-like porous Si consisting of 3D interconnected Si nanoligaments and bicontinuous nanopores prevents pulverization and accommodates volume expansion during cycling.The Si_(3)N_(4) offers mechanically protective coating to endow highly structural integrity and inhibit superfluous formation of SEI.The fast ion conducting Li_(3)N generated in situ from lithiation of active SiN_(x) facilitates Li ion transport.Consequently,the p-Si@SiN anode has appealing electrochemical properties such as a high capacity of 2180 mAh g^(-1)at 0.5 A g^(-1) with 84%capacity retention after 200cycles and excellent rate capacity with discharge capacity of 721 mAh g^(-1) after 500 cycles at 5.0 A g^(-1).This work provides insights into the rational design of active/inactive nanocoating on Si-based anode materials for fast-charging and highly stable LIBs.展开更多
Polyimide(PI)composite films were synthesized incorporating amino modified silicon nitride(Si_(3)N_(4))nanoparticles into PI matrix via in situ polymerization technique.The mechanical and thermal performances as well ...Polyimide(PI)composite films were synthesized incorporating amino modified silicon nitride(Si_(3)N_(4))nanoparticles into PI matrix via in situ polymerization technique.The mechanical and thermal performances as well as the hydrophobic properties of the as prepared composite films were investigated with respect to the dosage of the filler in the PI matrix.According to Thermogravimetric(TGA)analysis,meaningful improvements were achieved in T5(5%weight loss temperature)and T10(10%weight loss temperature)up to 54.1℃ and 52.4℃,respectively when amino functionalized nano Si_(3)N_(4) particles were introduced into the PI matrix.The differential scanning calorimetry(DSC)results revealed that the glass transition temperature(Tg)of the composites was considerably enhanced up to 49.7℃ when amino functionalized Si_(3)N_(4) nanoparticles were incorporated in the PI matrix.Compared to the neat PI,the PI/Si_(3)N_(4) nanocomposites exhibited very high improvement in the tensile strength as well as Young’s modulus up to 105.4%and 138.3%,respectively.Compared to the neat PI,the composites demonstrated highly decreased water absorption behavior which showed about 68.1%enhancement as the content of the nanoparticles was increased to 10 wt%.The SEM(Scanning electron microscope)images confirmed that the enhanced thermal,mechanical and water proof properties are essentially attributed to the improved compatibility of the filler with the matrix and hence,enhanced distribution inside the matrix because of the amino groups on the surface of Si_(3)N_(4) nanoparticles obtained from surface functionalization.展开更多
Self-reinforced Si_3N_4 ceramics containing high oxynitride glass have beenfabricated by the control of microstructure evolution and p-Si_3N_4 grain growth. The effects of thesize distribution of the elongated p-Si_3N...Self-reinforced Si_3N_4 ceramics containing high oxynitride glass have beenfabricated by the control of microstructure evolution and p-Si_3N_4 grain growth. The effects of thesize distribution of the elongated p-Si_3N_44 grains, and the p-Si_3N_4 grain growth as well as theoxynitride glass chemical characteristic on the microstructure and mechanical properties wereinvestigated. The experimental results show that the p-Si_3N_4 grains in high oxynitride glass growto elongated rod-like crystals and form the stereo-network structure. Under the sintering conditionsof 1800 deg C and 60 min, a quite uniform microstructure with an average aspect ratio of 6.5 and anaverage of 1 mu m can be obtained. A large amount of oxynitride glass phase with high nitrogencontent enhances the elevated temperature fracture toughness because of its high softeningtemperature and high viscosity. In the present material, the crack deflection and pullout of theelongated rod-like P-Si_3N_44 grains are the primary toughening mechanisms.展开更多
氮化硅是一种良好的载体,具有较高的水热稳定性和机械稳定性,其表面的氨基基团能够较好地锚定金属,显著提高金属分散度。但是,商品氮化硅比表面积较低,对金属分散作用仍然有限。因此,以自制的高比表面积氮化硅(Si_(3)N_(4))为载体,通过...氮化硅是一种良好的载体,具有较高的水热稳定性和机械稳定性,其表面的氨基基团能够较好地锚定金属,显著提高金属分散度。但是,商品氮化硅比表面积较低,对金属分散作用仍然有限。因此,以自制的高比表面积氮化硅(Si_(3)N_(4))为载体,通过浸渍法制备了不同Ru负载量(质量分数分别为0.5%、1.0%和2.0%)的催化剂(分别为0.5%Ru/Si_(3)N_(4)、1.0%Ru/Si_(3)N_(4)和2.0%Ru/Si_(3)N_(4)),并以商品氮化硅(Si_(3)N_(4)-C)为载体制备了2.0%Ru/Si_(3)N_(4)-C催化剂作为对照组。表征了催化剂的理化性质,测试了其在300℃、0.1 MPa下的CO_(2)加氢反应活性。结果显示,与Si_(3)N_(4)-C相比,Si_(3)N_(4)的比表面积较高(502 m^(2)/g),Si_(3)N_(4)作为载体显著提高了金属分散度,降低了金属粒径,催化剂暴露出更多的活性位点。0.5%Ru/Si_(3)N_(4)的金属粒径较小,展现出强的H_(2)吸附能力,H难以解吸,抑制了中间物种CO加氢生成CH_(4)。随着Ru负载量增加,金属粒径增大,催化剂的CH_(4)选择性更好。Ru/Si_(3)N_(4)系列催化剂中,2.0%Ru/Si_(3)N_(4)的CH_(4)选择性较高(98.8%)。空速为10000 m L/(g·h)时,0.5%Ru/Si_(3)N_(4)的CO选择性为88.2%。与2.0%Ru/Si_(3)N_(4)相比,2.0%Ru/Si_(3)N_(4)-C的金属粒径更大,活性位点较少,活性更低。2.0%Ru/Si_(3)N_(4)和2.0%Ru/Si_(3)N_(4)-C的CO_(2)转化率分别为53.1%和9.2%。Si_(3)N_(4)有效提高了金属分散度,提高了催化剂的CO_(2)加氢反应活性;通过调控Ru负载量控制催化剂金属粒径,可实现对产物CO或CH_(4)选择性的调控。展开更多
基金Funded by the National Science Foundation of China ( No.50375037)
文摘Si3N4-Si2N2O composites were fabricated with amorphous nano-sized silicon nitride powders by the liquid phase sintering （ LPS ）. The Si2 N2O phase was generated by an in-situ reaction 2 Si3 N4 （ s ） ＋ 1.5 02 （ g ） = 3 Si2 N2O （ s ） ＋ N2 （ g ） . The content of Si2 N2 O phase up to 60% in the volume was obtained at a sintering temperature of 1 650℃ and reduced when the sintering temperature increased or decreased, indicating the reaction is reversible. The mass loss, relative density and average grain size increased with increasing the sintering temperature. The average grain size was less than 500 nm when the sintering temperature was below 1 700 ℃. The sintering procedure contains a complex crystallization and a phase transition ： amorphous silicon nitride→equiaxial α- Si3 N4→ equiaxial β- Si3 N4→ rod- like Si2 N2O→ needle- like β- Si3N4 . Small round-shaped β→ Si3 N4 particles were entrapped in the Si2 N2O grains and a high density of staking faults was situated in the middle of Si2 N2O grains at a sintering temperature of 1 650 ℃. The toughness inereased from 3.5 MPa·m^1/2 at 1 600 ℃ to 7.2 MPa· m^1/2 at 1 800 ℃ . The hardness was as high as 21.5 GPa （Vickers） at 1 600 ℃ .
基金financially supported by the National Natural Science Foundation of China (U2004210, 51974208, U2003130, 21875080, 52002297)the Outstanding Youth Foundation of Natural Science Foundation of Hubei Province (2020CFA099)+2 种基金the Special Project of Central Government for Local Science and Technology Development of Hubei Province (2019ZYYD024)the Innovation group of Natural Science Foundation of Hubei Province (2019CFA020)the City University of Hong Kong Strategic Research Grants (7005505)。
文摘Silicon (Si) is a promising anode material for next-generation high-energy lithium-ion batteries (LIBs) due to its high capacity.However,the large volumetric expansion,poor ion conductivity and unstable solid electrolyte interface (SEI) lead to rapid capacity fading and low rate performance.Herein,we report Si nitride (SiN) comprising stoichiometric Si_(3)N_(4) and Li-active anazotic SiN_(x) coated porous Si (p-Si@SiN)for high-performance anodes in LIBs.The ant-nest-like porous Si consisting of 3D interconnected Si nanoligaments and bicontinuous nanopores prevents pulverization and accommodates volume expansion during cycling.The Si_(3)N_(4) offers mechanically protective coating to endow highly structural integrity and inhibit superfluous formation of SEI.The fast ion conducting Li_(3)N generated in situ from lithiation of active SiN_(x) facilitates Li ion transport.Consequently,the p-Si@SiN anode has appealing electrochemical properties such as a high capacity of 2180 mAh g^(-1)at 0.5 A g^(-1) with 84%capacity retention after 200cycles and excellent rate capacity with discharge capacity of 721 mAh g^(-1) after 500 cycles at 5.0 A g^(-1).This work provides insights into the rational design of active/inactive nanocoating on Si-based anode materials for fast-charging and highly stable LIBs.
基金the National Natural Science Foundation of China(51373044)Natural Science Foundation of Heilongjiang Province of China(E2017018).
文摘Polyimide(PI)composite films were synthesized incorporating amino modified silicon nitride(Si_(3)N_(4))nanoparticles into PI matrix via in situ polymerization technique.The mechanical and thermal performances as well as the hydrophobic properties of the as prepared composite films were investigated with respect to the dosage of the filler in the PI matrix.According to Thermogravimetric(TGA)analysis,meaningful improvements were achieved in T5(5%weight loss temperature)and T10(10%weight loss temperature)up to 54.1℃ and 52.4℃,respectively when amino functionalized nano Si_(3)N_(4) particles were introduced into the PI matrix.The differential scanning calorimetry(DSC)results revealed that the glass transition temperature(Tg)of the composites was considerably enhanced up to 49.7℃ when amino functionalized Si_(3)N_(4) nanoparticles were incorporated in the PI matrix.Compared to the neat PI,the PI/Si_(3)N_(4) nanocomposites exhibited very high improvement in the tensile strength as well as Young’s modulus up to 105.4%and 138.3%,respectively.Compared to the neat PI,the composites demonstrated highly decreased water absorption behavior which showed about 68.1%enhancement as the content of the nanoparticles was increased to 10 wt%.The SEM(Scanning electron microscope)images confirmed that the enhanced thermal,mechanical and water proof properties are essentially attributed to the improved compatibility of the filler with the matrix and hence,enhanced distribution inside the matrix because of the amino groups on the surface of Si_(3)N_(4) nanoparticles obtained from surface functionalization.
文摘Self-reinforced Si_3N_4 ceramics containing high oxynitride glass have beenfabricated by the control of microstructure evolution and p-Si_3N_4 grain growth. The effects of thesize distribution of the elongated p-Si_3N_44 grains, and the p-Si_3N_4 grain growth as well as theoxynitride glass chemical characteristic on the microstructure and mechanical properties wereinvestigated. The experimental results show that the p-Si_3N_4 grains in high oxynitride glass growto elongated rod-like crystals and form the stereo-network structure. Under the sintering conditionsof 1800 deg C and 60 min, a quite uniform microstructure with an average aspect ratio of 6.5 and anaverage of 1 mu m can be obtained. A large amount of oxynitride glass phase with high nitrogencontent enhances the elevated temperature fracture toughness because of its high softeningtemperature and high viscosity. In the present material, the crack deflection and pullout of theelongated rod-like P-Si_3N_44 grains are the primary toughening mechanisms.
文摘氮化硅是一种良好的载体,具有较高的水热稳定性和机械稳定性,其表面的氨基基团能够较好地锚定金属,显著提高金属分散度。但是,商品氮化硅比表面积较低,对金属分散作用仍然有限。因此,以自制的高比表面积氮化硅(Si_(3)N_(4))为载体,通过浸渍法制备了不同Ru负载量(质量分数分别为0.5%、1.0%和2.0%)的催化剂(分别为0.5%Ru/Si_(3)N_(4)、1.0%Ru/Si_(3)N_(4)和2.0%Ru/Si_(3)N_(4)),并以商品氮化硅(Si_(3)N_(4)-C)为载体制备了2.0%Ru/Si_(3)N_(4)-C催化剂作为对照组。表征了催化剂的理化性质,测试了其在300℃、0.1 MPa下的CO_(2)加氢反应活性。结果显示,与Si_(3)N_(4)-C相比,Si_(3)N_(4)的比表面积较高(502 m^(2)/g),Si_(3)N_(4)作为载体显著提高了金属分散度,降低了金属粒径,催化剂暴露出更多的活性位点。0.5%Ru/Si_(3)N_(4)的金属粒径较小,展现出强的H_(2)吸附能力,H难以解吸,抑制了中间物种CO加氢生成CH_(4)。随着Ru负载量增加,金属粒径增大,催化剂的CH_(4)选择性更好。Ru/Si_(3)N_(4)系列催化剂中,2.0%Ru/Si_(3)N_(4)的CH_(4)选择性较高(98.8%)。空速为10000 m L/(g·h)时,0.5%Ru/Si_(3)N_(4)的CO选择性为88.2%。与2.0%Ru/Si_(3)N_(4)相比,2.0%Ru/Si_(3)N_(4)-C的金属粒径更大,活性位点较少,活性更低。2.0%Ru/Si_(3)N_(4)和2.0%Ru/Si_(3)N_(4)-C的CO_(2)转化率分别为53.1%和9.2%。Si_(3)N_(4)有效提高了金属分散度,提高了催化剂的CO_(2)加氢反应活性;通过调控Ru负载量控制催化剂金属粒径,可实现对产物CO或CH_(4)选择性的调控。
