以硝酸镍为镍源、酸/碱性硅溶胶为硅源,采用共沉淀法制备了2种Ni/SiO_(2)催化剂。采用固定床反应器,评价Ni/SiO_(2)催化剂对于2-甲基呋喃(2-MF)气相加氢合成2-甲基四氢呋喃(2-MTHF)的反应性能。通过XRD、N_(2)等温吸附-脱附、H_(2)-TPR...以硝酸镍为镍源、酸/碱性硅溶胶为硅源,采用共沉淀法制备了2种Ni/SiO_(2)催化剂。采用固定床反应器,评价Ni/SiO_(2)催化剂对于2-甲基呋喃(2-MF)气相加氢合成2-甲基四氢呋喃(2-MTHF)的反应性能。通过XRD、N_(2)等温吸附-脱附、H_(2)-TPR、NH3-TPD、XPS、FTIR和TEM对催化剂进行了表征。考察了硅溶胶的酸碱性对Ni/SiO_(2)催化剂结构及性能的影响。结果表明,以酸性硅溶胶为硅源制备的Ni/SiO_(2)催化剂以弱酸中心酸量为主且存在中强酸中心,比表面积、平均孔径大,因而该催化剂加氢活性和2-MTHF的选择性较高。Ni/SiO_(2)催化剂稳定性良好,在最优反应条件〔温度90℃、H_(2)压力2 MPa、质量空速4.4 g 2-MF/(g催化剂·h)、H_(2)与2-MF物质的量之比为4∶1〕下进行催化剂稳定性测试(200 h),2-MF的转化率达到99.8%,2-MTHF的选择性均保持在97.5%左右。展开更多
The effects of SiO_(2) content on the preparation process and metallurgical properties of acid oxidized pellets, including compressive strength, reduction, and softening–melting behaviors, were systematically investi...The effects of SiO_(2) content on the preparation process and metallurgical properties of acid oxidized pellets, including compressive strength, reduction, and softening–melting behaviors, were systematically investigated.Mineralogical structures, elemental distribution, and pore size distribution were varied to analyze the mechanism of the effects.The results show that with an increase in SiO_(2) content from 3.51 wt%to 7.18 wt%, compressive strength decreases from 3150 N/pellet to 2100 N/pellet and reducibility decreases from 76.5% to 71.4%.The microstructure showed that pellets with high SiO_(2) content contained more magnetite in the mineralogical structures.Additionally, some liquid phases appeared, which hindered the continuous crystallization of hematite.Also, the softening–melting properties of the pellets clearly deteriorated as the SiO_(2) content increased.With increasing SiO_(2) content, the temperature range of the softening–melting zone decreased, and the maximum differential pressure and the comprehensive permeability index increased significantly.When acid oxidized pellets are used as the raw materials for blast furnace smelting, it should be combined with high basicity sinters to improve the softening–melting behaviors of the comprehensive charge.展开更多
Synthesis of acetic acid by direct oxidation of ethylene on Pd-H4SiW12O40-based catalysts was studied in a fixed-bed integral reactor and a pulse differential reactor. From the performance of the catalysts with differ...Synthesis of acetic acid by direct oxidation of ethylene on Pd-H4SiW12O40-based catalysts was studied in a fixed-bed integral reactor and a pulse differential reactor. From the performance of the catalysts with different compositions and configurations, it is proposed that acetic acid is predominantly produced via an intermediate of acetaldehyde. This can be easily confirmed by comparing the product distributions in the integral and the differential reactors. The active sites for acetic acid formation are considered to exist mainly at the boundaries between the H4SiW12O40 and the Pd particles. The Pd-based catalysts reduced by H2/N2 have higher activities than those reduced by hydrazine, as explained by the degree of Pd dispersion obtained from the characteristics of hydrogen chemical adsorption. It was found that the Pd-Se-SiW12/SiO2 catalyst with selenium tetrachloride as a precursor was more active than that with potassium selenite, and that the acetic acid yield can be greatly increased by adding a suitable amount of dichloroethane (C2H4C12/C2H4 mole ratio=0.03) to the reactants.展开更多
To improve the cracking behavior of hydrocarbon,Ni-Mo/SiO_(2) bimetallic catalysts were synthesized by different preparation methods(sol-gel,co-impregnation and single-impregnation) and added the additives(citric acid...To improve the cracking behavior of hydrocarbon,Ni-Mo/SiO_(2) bimetallic catalysts were synthesized by different preparation methods(sol-gel,co-impregnation and single-impregnation) and added the additives(citric acid,polyethylene glycol and cetyltrimethylammonium bromide) based on the most suitable method above.The cracking reaction of methylcyclohexane under supercritical conditions was performed as the probe reaction to estimate the catalytic performance,and the properties of Ni-Mo/SiO_(2) catalyst were characterized by N_(2) absorption-desorption,XRD,XPS,H_(2)-TPR,NH_(3)-TPD,in-situ IR of NH_(3) desorption,HRTEM and STEM-mapping so as to study the structure-activity relationship.The catalyst synthesized via sol-gel method showed the best conversion and heat sink,being 81.8% and 3.81 MJ/kg,which was closely related to strong mutual effect between active components and SiO_(2) as well as strong acid sites.Besides,the introduction of additives by sol-gel method has an affirmative influence on properties of Ni-Mo/SiO_(2) catalysts,being that the acidity(more L and B acid sites) was modulated and organic groups interact with metal to suppress the aggregation of metal species(Ni and Mo),thereby enhancing the catalytic activity.At 750℃,the conversion(89.3%) as well as heat sink(3.99 MJ/kg) of MCH cracking obtained an optimum over Ni-Mo/SiO_(2) catalyst with addition of citric acid.展开更多
In this paper,a low-cost and environmental-friendly leaching agent citric acid(C_(6)H_(8)O_(7))was used to treat the sediment of Dianchi Lake(SDL)to synthesize lithium silicate(Li_(4)SiO_(4))based CO_(2)sorbent.The re...In this paper,a low-cost and environmental-friendly leaching agent citric acid(C_(6)H_(8)O_(7))was used to treat the sediment of Dianchi Lake(SDL)to synthesize lithium silicate(Li_(4)SiO_(4))based CO_(2)sorbent.The results were compared with that treated with strong acid.Moreover,the effects of preparation conditions,sorption conditions and desorption conditions on the CO_(2)sorption performance of prepared Li_(4)SiO_(4)were systematically studied.Under optimal conditions,the Li_(4)SiO_(4)sorbent was successfully synthesized and its CO_(2)sorption capacity reached 31.37%(mass),which is much higher than that synthesized from SDL treated with strong acid.It is speculated that the presence of some elements after C_(6)H_(8)O_(7)treatment may promote the sorption of synthetic Li_(4)SiO_(4)to CO_(2).In addition,after doping with K_(2)CO_(3),the CO_(2)uptake increases from the original 12.02%and 22.12%to 23.96%and 32.41%(mass)under the 20%and 50%CO_(2)partial pressure,respectively.More importantly,after doping K_(2)CO_(3),the synthesized Li_(4)SiO_(4)has a high cyclic stability under the low CO_(2)partial pressure.展开更多
文摘以硝酸镍为镍源、酸/碱性硅溶胶为硅源,采用共沉淀法制备了2种Ni/SiO_(2)催化剂。采用固定床反应器,评价Ni/SiO_(2)催化剂对于2-甲基呋喃(2-MF)气相加氢合成2-甲基四氢呋喃(2-MTHF)的反应性能。通过XRD、N_(2)等温吸附-脱附、H_(2)-TPR、NH3-TPD、XPS、FTIR和TEM对催化剂进行了表征。考察了硅溶胶的酸碱性对Ni/SiO_(2)催化剂结构及性能的影响。结果表明,以酸性硅溶胶为硅源制备的Ni/SiO_(2)催化剂以弱酸中心酸量为主且存在中强酸中心,比表面积、平均孔径大,因而该催化剂加氢活性和2-MTHF的选择性较高。Ni/SiO_(2)催化剂稳定性良好,在最优反应条件〔温度90℃、H_(2)压力2 MPa、质量空速4.4 g 2-MF/(g催化剂·h)、H_(2)与2-MF物质的量之比为4∶1〕下进行催化剂稳定性测试(200 h),2-MF的转化率达到99.8%,2-MTHF的选择性均保持在97.5%左右。
基金financially supported by the Key Program of the National Natural Science Foundation of China (No.U1360205)the Natural Science Foundation of Hebei Province of China (No.E2019209424)。
文摘The effects of SiO_(2) content on the preparation process and metallurgical properties of acid oxidized pellets, including compressive strength, reduction, and softening–melting behaviors, were systematically investigated.Mineralogical structures, elemental distribution, and pore size distribution were varied to analyze the mechanism of the effects.The results show that with an increase in SiO_(2) content from 3.51 wt%to 7.18 wt%, compressive strength decreases from 3150 N/pellet to 2100 N/pellet and reducibility decreases from 76.5% to 71.4%.The microstructure showed that pellets with high SiO_(2) content contained more magnetite in the mineralogical structures.Additionally, some liquid phases appeared, which hindered the continuous crystallization of hematite.Also, the softening–melting properties of the pellets clearly deteriorated as the SiO_(2) content increased.With increasing SiO_(2) content, the temperature range of the softening–melting zone decreased, and the maximum differential pressure and the comprehensive permeability index increased significantly.When acid oxidized pellets are used as the raw materials for blast furnace smelting, it should be combined with high basicity sinters to improve the softening–melting behaviors of the comprehensive charge.
文摘Synthesis of acetic acid by direct oxidation of ethylene on Pd-H4SiW12O40-based catalysts was studied in a fixed-bed integral reactor and a pulse differential reactor. From the performance of the catalysts with different compositions and configurations, it is proposed that acetic acid is predominantly produced via an intermediate of acetaldehyde. This can be easily confirmed by comparing the product distributions in the integral and the differential reactors. The active sites for acetic acid formation are considered to exist mainly at the boundaries between the H4SiW12O40 and the Pd particles. The Pd-based catalysts reduced by H2/N2 have higher activities than those reduced by hydrazine, as explained by the degree of Pd dispersion obtained from the characteristics of hydrogen chemical adsorption. It was found that the Pd-Se-SiW12/SiO2 catalyst with selenium tetrachloride as a precursor was more active than that with potassium selenite, and that the acetic acid yield can be greatly increased by adding a suitable amount of dichloroethane (C2H4C12/C2H4 mole ratio=0.03) to the reactants.
基金supported by National Natural Science Foundation of China [grant number 91841301]Fundamental Research Funds for the Central Universities [grant number YJ201791]。
文摘To improve the cracking behavior of hydrocarbon,Ni-Mo/SiO_(2) bimetallic catalysts were synthesized by different preparation methods(sol-gel,co-impregnation and single-impregnation) and added the additives(citric acid,polyethylene glycol and cetyltrimethylammonium bromide) based on the most suitable method above.The cracking reaction of methylcyclohexane under supercritical conditions was performed as the probe reaction to estimate the catalytic performance,and the properties of Ni-Mo/SiO_(2) catalyst were characterized by N_(2) absorption-desorption,XRD,XPS,H_(2)-TPR,NH_(3)-TPD,in-situ IR of NH_(3) desorption,HRTEM and STEM-mapping so as to study the structure-activity relationship.The catalyst synthesized via sol-gel method showed the best conversion and heat sink,being 81.8% and 3.81 MJ/kg,which was closely related to strong mutual effect between active components and SiO_(2) as well as strong acid sites.Besides,the introduction of additives by sol-gel method has an affirmative influence on properties of Ni-Mo/SiO_(2) catalysts,being that the acidity(more L and B acid sites) was modulated and organic groups interact with metal to suppress the aggregation of metal species(Ni and Mo),thereby enhancing the catalytic activity.At 750℃,the conversion(89.3%) as well as heat sink(3.99 MJ/kg) of MCH cracking obtained an optimum over Ni-Mo/SiO_(2) catalyst with addition of citric acid.
基金the financial support from National Natural Science Foundation of China(21868015,51802135)the Applied Basic Research Programs of Yunnan Province(140520210057)+1 种基金Taif University Researchers Supporting Project number(TURSP-2020/163)Taif University,Taif,Saudi Arabia。
文摘In this paper,a low-cost and environmental-friendly leaching agent citric acid(C_(6)H_(8)O_(7))was used to treat the sediment of Dianchi Lake(SDL)to synthesize lithium silicate(Li_(4)SiO_(4))based CO_(2)sorbent.The results were compared with that treated with strong acid.Moreover,the effects of preparation conditions,sorption conditions and desorption conditions on the CO_(2)sorption performance of prepared Li_(4)SiO_(4)were systematically studied.Under optimal conditions,the Li_(4)SiO_(4)sorbent was successfully synthesized and its CO_(2)sorption capacity reached 31.37%(mass),which is much higher than that synthesized from SDL treated with strong acid.It is speculated that the presence of some elements after C_(6)H_(8)O_(7)treatment may promote the sorption of synthetic Li_(4)SiO_(4)to CO_(2).In addition,after doping with K_(2)CO_(3),the CO_(2)uptake increases from the original 12.02%and 22.12%to 23.96%and 32.41%(mass)under the 20%and 50%CO_(2)partial pressure,respectively.More importantly,after doping K_(2)CO_(3),the synthesized Li_(4)SiO_(4)has a high cyclic stability under the low CO_(2)partial pressure.
