Dynamic Response Impact of Vehicle Braking on Simply Supported Beam Bridges with Corrugated Steel Webs Based on Vehicle-Bridge Coupled Vibration Analysis

A novel approach for analyzing coupled vibrations between vehicles and bridges is presented,taking into account spatiotemporal effects and mechanical phenomena resulting fromvehicle braking.Efficient modeling and solution of bridge vibrations induced by vehicle deceleration are realized using this method.The method’s validity and reliability are substantiated through numerical examples.A simply supported beam bridge with a corrugated steel web is taken as an example and the effects of parameters such as the initial vehicle speed,braking acceleration,braking location,and road surface roughness on the mid-span displacement and impact factor of the bridge are analyzed.The results show that vehicle braking significantly amplifies mid-span displacement and impact factor responses in comparison to uniform vehicular motion across the bridge.Notably,the influence of wheelto-bridge friction forces is of particular significance and cannot be overlooked.When the vehicle initiates braking near the middle of the span,both the mid-span displacement and impact factor of the bridge exhibit substantial increases,further escalating with higher braking acceleration.Under favorable road surface conditions,the midspan displacement and the impact factor during vehicle braking may exceed the design values stipulated by codes.It is important to note that road surface roughness exerts a more pronounced effect on the impact factor of the bridge in comparison to the effects of vehicle braking.

Discussion on Detection and Evaluation of Simply Supported Prestressed Concrete Small Box Girder Bridge After a Fire

The article takes a simply supported prestressed concrete small box girder bridge project as an example for inspection and evaluation after a fire incident.This includes appearance detection,concrete color hardness detection,concrete strength detection,concrete surface damage layer detection,reinforcement protective layer detection,and concrete carbonation detection.It is hoped that this analysis can be used as a reference for the detection and evaluation of future bridge projects with fire incidents to smoothen its subsequent repair and maintenance.

Effect of temperature difference load of 32 m simply supported box beam bridge on track vertical irregularity

In order to study the effect of temperature difference load （TDL） along the vertical direction of a simply supported beam bridge section on the vertical irregularity, a rail-bridge-piers calculation model was established. Taking 32 m simply supported box beam bridge which is widely used in the construction of pas- senger dedicated line in China as an example, influences of the temperature variation between the bottom and top of the bridge, temperature curve index, type of temperature gradient, and beam height on track vertical irregularity were analyzed with the model. The results show that TDL has more effects on long wave track irregularity than on short one, and the wavelength mainly affected is approxi- mately equal to the beam span. The amplitude of irregu- larity caused by TDL is largely affected by the temperature variation, temperature curve index, and type of temperature gradient, so it is necessary to monitor the temperaturedistribution of bridges in different regions to provide accurate calculation parameters. In order to avoid the irregularity exceeding the limit values, the height of 32, 48, and 64 m simply supported box beam bridges must not be less than 2.15, 3.2, and 4.05 m, respectively.

Damage Identification in Simply Supported Bridge Based on Rotational-Angle Influence Lines Method

To locate and quantify local damage in a simply supported bridge, in this study, we derived a rotational-angle influence line equation of a simply supported beam model with local damage. Using the diagram multiplication method, we introduce an analytical formula for a novel damage-identification indicator, namely the diff erence of rotational-angle influence linescurvature(DRAIL-C). If the initial stiff ness of the simply supported beam is known, the analytical formula can be effectively used to determine the extent of damage under certain circumstances. We determined the effectiveness and anti-noise performance of this new damage-identification method using numerical examples of a simply supported beam, a simply supported hollow-slab bridge, and a simply supported truss bridge. The results show that the DRAIL-C is directly proportional to the moving concentrated load and inversely proportional to the distance between the bridge support and the concentrated load and the distance between the damaged truss girder and the angle measuring points. The DRAIL-C indicator is more sensitive to the damage in a steel-truss-bridge bottom chord than it is to the other elements.

Pure bending of simply supported circular plate of transversely isotropic functionally graded material

This paper considers the pure bending problem of simply supported transversely isotropic circular plates with elastic compliance coefficients being arbitrary functions of the thickness coordinate. First, the partial differential equation, which is satisfied by the stress functions for the axisymmetric deformation problem is derived. Then, stress functions are obtained by proper manipulation. The analytical expressions of axial force, bending moment and displacements are then deduced through integration. And then, stress functions are employed to solve problems of transversely isotropic functionally graded circular plate, with the integral constants completely determined from boundary conditions. An elasticity solution for pure bending problem, which coincides with the available solution when degenerated into the elasticity solutions for homogenous circular plate, is thus obtained. A numerical example is finally presented to show the effect of material inhomogeneity on the elastic field in a simply supported circular plate of transversely isotropic functionally graded material (FGM).

Analytical solutions of simply supported magnetoelectroelastic circular plate under uniform loads

In this paper, the axisymmetric general solutions of transversely isotropic magnetoelectroelastic media are expressed with four harmonic displacement functions at first. Then, based on the solutions, the analytical three-dimensional solutions are provided for a simply supported magnetoelectroelastic circular plate subjected to uniform loads. Finally, the example of circular plate is presented.

Influence of key factors on deflection of bonded prestressed concrete simply supported slabs subjected to fire

In order to validate the accuracy of nonlinear fire simulation programs,comparison analysis is carried out between simulation and experiment induced from small-scale specimens,and then fire resistance of large-scale prestressed concrete slabs is further investigated through parameter expansion.The influences on fire resistance ratings controlled by deflection are explored and discussed,including effective span,concrete cover thickness,load level,prestress degree,effective prestress,composite reinforcement index and other factors.The calculated results indicate that fire resistance ratings of large-scale bonded prestressed concrete simply supported slabs are bigger than those of small-scale ones.Finally,the calculation formulas of fire resistance ratings controlled by deflection are established,which rationally consider the influence of effective span,concrete cover thickness,load level,composite reinforcement index and so on key factors.

Wind tunnel measurement of aerodynamic characteristics of trains passing each other on a simply supported box girder bridge

The aerodynamic performance of high-speed trains passing each other was investigated on a simply supported box girder bridge,with a span of 32 m,under crosswinds.The bridge and train models,modeled at a geometric scale ratio of 1:30,were used to test the aerodynamic forces of the train,with the help of a designed moving test rig in the XNJD-3 wind tunnel.The effects of wind speed,train speed,and yaw angle on the aerodynamic coefficients of the train were analyzed.The static and moving model tests were compared to demonstrate how the movement of the train influences its aerodynamic characteristics.The results show that the sheltering effect introduced by trains passing each other can cause a sudden change in force on the leeward train,which is further influenced by the wind and running speeds.Detailed analyses related to the effect of wind and train speeds on the aerodynamic coefficients were conducted.The relationship between the change in aerodynamic coefficients and yaw angle was finally described by a series of proposed fitting formulas.

ANALYTICAL SOLUTION OF A SIMPLY SUPPORTED PIEZOELECTRIC BEAM SUBJECTED TO A UNIFORMLY DISTRIBUTED LOADING

Using the inverse method, the analytical solution of a simply supported piezoelectric beam subjected to a uniformly distributed loading has been studied.First,the polynomials of stress function and induction function are given.Then, considering the gradient properties of the elastic parameter and the potential funciton as well as the piezoelectric parameter,the analytical solution of a simply supported beam subjected to a uniformly distributed loading is obtained and discussed.

Analytical Solutions to Strain Rates of Reinforced Concrete Simply Supported Slabs under Blast Loads

Based on the Duhamel integral, a couple of analytical solutions are derived to predict the strain rates of concrete and steel reinforcement in reinforced concrete slabs under blast loads and to estimate their variation over depth of a cross-section along the entire length of the member. The analytical approach utilizes the single-degree-of-freedom mode for the analysis of reinforced concrete simply supported one-way panels subjected to blast loads. These analytical solutions can give the strain rate profile for any cross-section at any time and permit variations of strain rate in each time step of numerical iteration method, thus making it possible to directly incorporate strain rate effects into non-linear dynamic response analysis of structural members subjected to blast loads.

Temporary Bearing Method in Construction of Continuous Beam Bridge Erected as Simply-Supported Beam

The present practice in Bangladesh for erection of girders is placing the girder directly on the bearing pad and joining the adjacent two spans in deck slab level by adopting expansion joints, as the bridges are presently designed as simply-supported beam bridge. The main disadvantage of this type of bridges is that, the seismic resistance is weak, and under the external force beyond the design range, the bridges are more likely to fall in danger because of failure in girders. Also they have expansion joints for each span, which affects the comfort of driving and the overall integrity of the bridge deck is poor [1]. Therefore, design and construction of the bridges have been revised to establish continuity between girders of two adjacent spans and transform the bridge as simply supported continuous beam bridge [2]. Temporary bearing (sandbox) method is proposed in this paper to solve the system transformation of continuous beam bridges. Design of the temporary bearing is very simple and can be manufactured at site. This method has been proved in construction of Arial Kha Bridge and can be applied for other similar bridges in Bangladesh.

STABILITY AND LOCAL BIFURCATION IN A SIMPLY-SUPPORTED BEAM CARRYING A MOVING MASS

The stability and local bifurcation of a simply-supported flexible beam （Bernoulli- Euler type） carrying a moving mass and subjected to harmonic axial excitation are investigated. In the theoretical analysis, the partial differential equation of motion with the fifth-order nonlinear term is solved using the method of multiple scales （a perturbation technique）. The stability and local bifurcation of the beam are analyzed for 1/2 sub harmonic resonance. The results show that some of the parameters, especially the velocity of moving mass and external excitation, affect the local bifurcation significantly. Therefore, these parameters play important roles in the system stability.

THE DYNAMIC PLASTIC BEHAVIOR OF A SIMPLY SUPPORTED CIRCULAR PLATE IN A DAMPING MEDIUM WITH FINITE-DEFLECTIONS

A theoretical analysis is presented for the dynamic plastic behavior of a simply supported rigid, perfectly plastic circular plate in damping medium with finite-deflections subjected to a rectangular pressure pulse. Analytical solutions of every moving stage under both medium and high loads are developed.

BENDING OF UNIFORMLY LOADED RECTANGULAR PLATES WITH TWO ADJACENT EDGES CLAMPED, ONE EDGE SIMPLY SUPPORTED AND THE OTHER EDGE FREE

In this paper, an exact solution for an uniformly loaded rectangular plate with two adjacent edges clamped, one edge simply supported and the other edge free, was given by using the concept of generalized simply supported edges and superposition method. The numerical results were given for the deflections along the free edge and bending moments along the clamped edges of a square plate.

Vibration Analysis of a Simply Supported Beam Traversed by Uniform Distributed Moving Load

Considering the engineering background of some transportation system like maglev, vertical vibration of the simply supported beam is investigated. The length of the vehicle is assumed to be longer than the beam span. The model of moving distributed load with constant speed is established .The beam can be taken as Euler-Bernoulli beam model and the right side of the control equation is simplified by using a moving status function. Duhamel integral and mode superposition method is used to solve the dynamic behavior of the beam. In this aspect deflection and acceleration are included. The results of different parameters such as the span of beam, velocity of load and ratio vehicle-Beam masses are compared. All results show that the dynamic response of the beam is tied up with these factors: the frequency of the beam, the moving frequency of the load and the ratio of vehicle-beam mass.

EXACT SOLUTION FOR RECTANGULAR SLAB WITH THREE EDGES SIMPLY-SUPPORTED AND OTHER FREE

In this paper,we give all-sided pastic analysis of the rectangular slab with three edges simply-supported and other free.Here we discuss the following four cases:(1)The uniformly distributedload over the area a slab.(2).A concentrated load act at midpoint of free edges slab.(3)A concen-trated load act at the center a slab.(4)The line load act along free edge of slab.

Effect of Web Opening on Buckling Instability of Simply Supported Steel I-Beam

The lateral torsional buckling phenomenon often governs design of steel I-beams. Although web opening is often used to accommodate the required mechanical and piping works in buildings, its effect on the buckling instability is not considered in the design codes. In this paper, the effect of web opening on both lateral torsional buckling and local buckling behaviors has been investigated. A simply supported steel I-beam has been studied under uniform bending moment around the major axis. Buckling analysis has been performed using the finite element method. Linear regression analysis has been conducted for output data to formulate an equation for the critical moment including web opening effect. The results have shown a limited reduction in the lateral torsional buckling capacity and a significant reduction in the local buckling capacity.

THE APPLICATION OF WEINSTEIN-CHIEN′S METHOD——THE UPPER AND LOWER LIMITS OF FUNDAMENTAL FREQUENCY OF RECTANGULAR PLATES WITH EDGES ARE THE MIXTURE OF SIMPLY SUPPORTED PORTIONS AND CLAMPED PORTIONS

In this paper, the method of relaxed boundary conditions is applied to rectangular plates with edges which are a sort of the mixture of simply supported portions and clamped portions, so that the lower limit of fundamental frequency of such plates is evaluated. A kind of polynomial satisfying the displacement boundary conditions is designed, os that it is enabled to evaluate the upper limit of fundamental frequency by Ritz' method. The practical calculation examples solved by these methods have given satisfactory results. At the end of this paper, it is pointed out that the socalled exact solution of such plates usually evaluated by the force superposition method is essentially a kind of lower limit of solution, if the truncated error of series which occurs in actual calculation is considered.

端钩型钢纤维混凝土简支梁受弯承载力试验

为改善普通钢筋混凝土梁自重大、易开裂、承载力低等缺点,在混凝土中常加入钢纤维,端钩型钢纤维,作为常见的一种高性能钢纤维得到广泛关注,中外学者针对端钩型钢纤维混凝土的基本力学性能开展了较多研究,而对端钩型钢纤维混凝土受弯构件的正截面受力性能有待深入研究。为研究端钩型钢纤维混凝土简支梁受弯性能,制作4根端钩型钢纤维混凝土梁及1根普通混凝土梁,对其进行受弯性能试验,根据试验得到的破坏形态、承载力、荷载-挠度曲线、荷载-应变曲线,分析端钩型钢纤维体积掺量对试件受弯承载力及破坏形态的影响。结果表明:端钩型钢纤维混凝土简支梁与一般混凝土简支梁受弯过程类似,均经历了弹性、开裂、带裂缝工作、破坏4个阶段;端钩型钢纤维混凝土简支梁与一般混凝土简支梁受弯过程均基本符合“平截面假定”;端钩型钢纤维限制了裂缝的产生和发展,使得纤维混凝土梁变形能力增强;与一般混凝土梁相比,端钩型钢纤维混凝土梁抗裂性及极限承载力得到提高,且构件承载力与钢纤维体积掺量基本呈现正相关;基于试验数据,对现行规范中开裂弯矩及极限承载力计算公式进行优化,开裂弯矩方面考虑对截面抵抗矩塑性影响系数进行修正,极限承载力方面引入纤维混凝土正截面承载力影响系数ζ,经修正计算值可较好吻合试验值。

基于主线不停运的城轨支线独立运营改造方案

研究目的:针对大型铁路枢纽接入已运营轨道交通线路引起的既有线改造问题,为满足铁路枢纽与轨道交通连接线(支线)施工期间主线正常运营不受影响,对改造涉及的运营组织与接轨方案进行系统研究,并对土建、轨道、接触网、环网与动照、信号、综合监控与通信系统等的改造及影响进行深入研究,在统筹考虑实施难度、投资与工期的基础上,提出实施风险最小、技术最合理的改造方案。研究结论:(1)既有高架车站与区间改造影响范围较小且相对可控,可以实现主线正常运营情况下新建独立运营支线工程;(2)为最大程度保障主线运营不受影响,在现有技术水平条件下,应尽量避免在运营天窗期进行各类信号光电缆的割接;(3)支线独立运营方案,应尽量采取措施将新建支线与主线相连、轨道相通,以利于车辆检修与维保,并增加运营的灵活性;(4)桥梁浇筑与平移施工临近既有线,实施阶段应进一步完善工艺衔接与交叉施工统筹,增加既有线安全保障;(5)本研究结论可为类似工程提供参考。