Single output LD end-pumped passively mode-locked Nd:YVO_4 laser with semiconductor saturable absorber mirror

A quarter-wave plate and the thin film polarizer （TFP） are used for the LD end-pumped passively mode-locked Nd：YVO4 laser with semiconductor saturable absorber mirror （SESAM） to obtain a single beam output with a total power of 4.8 W. An optical-optical efficiency is achieved to be 24% for a stable CW mode-locking operation at 1064 nm, with a pulse repetition rate of 70 MHz and pulse width of 16 ps. The multipulse in the pulse sequence is eliminated for reaching a peak power as high as 4 kW.

Embedded Programmable Single Point Multiple Output Intelligent Data Acquisition and Transmission System

To effectively solve the problems of inconsistent communication protocols in automatic monitoring equipment,and limited data acquisition transmission and monitoring equipment,this paper developed programmable single point multiple output intelligent data acquisition and transmission system. It made an in-depth elaboration of the data acquisition and transmission system from hardware design,software architecture and principle,main functions and technical parameters. Finally,it came up with four innovation points:(i) intelligent(automatic)matching a variety of communication protocols for environmental monitoring equipment,(ii) realizing multi-protocol and multi-target parallel data transmission,(iii) realizing remote dynamic input of control instructions through wired or wireless network,and(iv) supporting configuration(process) simulation of field equipment DCS operating conditions.

Loss Rate Estimation of Yield and Output Value of Tobacco Leaf Infected by Tobacco Blown Spot (Alternaria alternata)

[Objective] The paper was to study the effect of tobacco blown spot on the yield and output value of tobacco leaf.[Method]The upper,middle and lower leaves in tobacco plant were selected during the harvest period of tobacco to carry out loss rate estimation of yield and output value of tobacco leaf caused by different disease levels of brown spot.Regression correlation analysis was also conducted.[Result]The disease levels of brown spot had extremely significant strong negative correlation with single leaf weight of tobacco leaf,and it had extremely significant strong positive correlation with the loss rate of single leaf weight.The increase speed of loss rate of single leaf weight of middle and upper leaves was obviously faster than that of lower leaves.The loss rates of single leaf weight of upper,middle and lower leaves were 3.18%-28.95%,3.43%-28.88% and 10.07%-26.90%,respectively.The higher the disease level of blown spot was,the lower the yield and output value of tobacco leaf was,and the corresponding loss rate was also higher.Correlation analysis showed that the disease level of blown spot had extremely significant strong negative correlation with the yield and output value of tobacco leaf,and it had extremely significant strong positive correlation with the loss rate of yield and output value.The negative impact of blown spot on the output value of tobacco leaf was far greater than that on the yield.The highest loss rate of the yield of tobacco leaf was 28.56%,while the highest loss rate of output value reached 89.67%.[Conclusion] The study provided theoretical basis for accurately holding the critical period for the control of blown spot,thus reducing the damage on tobacco leaf and improving the output value of tobacco leaf.

Efficient Graph-based Genetic Programming Representation with Multiple Outputs

In this work, we explore and study the implication of having more than one output on a genetic programming （GP） graph-representation. This approach, called multiple interactive outputs in a single tree （MIOST）, is based on two ideas. First, we defined an approach, called interactivity within an individual （IWI）, which is based on a graph-GP representation. Second, we add to the individuals created with the IWI approach multiple outputs in their structures and as a result of this, we have MIOST. As a first step, we analyze the effects of IWI by using only mutations and analyze its implications （i.e., presence of neutrality）. Then, we continue testing the effectiveness of IWI by allowing mutations and the standard GP crossover in the evolutionary process. Finally, we tested the effectiveness of MIOST by using mutations and crossover and conducted extensive empirical results on different evolvable problems of different complexity taken from the literature. The results reported in this paper indicate that the proposed approach has a better overall performance in terms of consistency reaching feasible solutions.

Non-fragile Dynamic Output Feedback H∞Control for a Class of Un­certain Switched Systems with Time-varying Delay

The problem of non-fragile dynamic output feedback H∞control for a class of uncertain switched systems with time-varying delay is discussed.Firstly,the form of non-fragile dynamic output feedback H∞controller is given.Under the condition that the upper bound of time delay and the upper bound of delay derivative are limited simultaneously,Lyapunov functional and its corresponding switching rules are constructed by using single Lyapunov function method and convex combination technique;Secondly,we use the inequality lemma to scale the derived Lyapunov functional in order to eliminate the time-varying delay term in the in­equality,and then introduce the J-function to obtain a nonlinear matrix in­equality that satisfies the H∞performance indexγ,we also employ Schur complement lemma to transform the nonlinear matrix inequality into set of linear matrix inequalities consisting of two linear matrix inequalities,a sufficient condition for the existence of a non-fragile dynamic output feedback H∞controller and satisfying the H∞performance indexγis concluded for a class of uncertain switching systems with variable time delay;Finally,a switched system composed of two subsystems is consid­ered and the effectiveness and practicability of the theorem are illustrated by numerical simulation with LMI toolbox.

Optimal Output Power Control of Switched Reluctance Generator at a Constant Speed

In order to control the output power of a switched reluctance generator(SRG)at a constant speed,the output power of SRG is theoretically analyzed by using freewheeling control.First,through a theoretical analysis,a finite element simulation and an experiment,it was verified that the output power of SRG cannot be improved by using freewheeling control with a single pulse control method(SPCM).Then,the maximum output power can be obtained by optimizing the turn off angles of SPCM at a constant speed,and at the same time,the formula of the optimal turn-off angle was presented,which meets the criterion for the output power maximization.Finally,numerical simulation and experimental results demonstrated the validity of the theoretical analysis.

An Improved Design of a Fully Automated Multiple Output Micropotentiometer

This paper describes in details a new design of a fully automated multiple output micropotentiometer (?pot). A prototype has been built at the National Institute for Standards (NIS), Egypt to establish this highly improved AC voltage source in the millivolt range. The new device offers three different outputs covering a wide frequency range from only one outlet. This valuably supports the precise sourcing ranges of low AC voltage at NIS. The design and the operation theory of this prototype have been discussed in details. An automatic calibration technique has been introduced through specially designed software using the LabVIEW program to enhance the calibration technique and to reduce the uncertainty contributions. Relative small AC-DC differences of our prototype in the three output ranges are fairly verified. The expanded uncertainties of the calibration results for the three output ranges have been faithfully estimated. However, further work is needed to achieve the optimum performance of this new device.

The Nexus between Nigerian Government Spending and Domestic Output in the Presence of Long-Term Crude Oil Price Shock: A Conditional Unrestricted Equilibrium Correction Model Approach

This paper is an empirical analysis of provisional unrestricted level relationship between Nigerian domestic output measured by Gross Domestic Product (GDP) and government spending proxied by capital and recurrent expenditures in the presence of static regressors such as crude oil prices and federal government retained revenues. We estimate an ARDL (1,0,1) using a single-equation approach. Results show that government expenditures have negative but statistically insignificant effects on domestic output in the long-run. Similarly, negative short run effects are established amongst the variables. However, recurrent expenditure is statistically significant in the short-run. Whilst federal government retained revenue has a positive and significant effect, crude oil price exhibited negative relationships with domestic output both at level and in the short-run dynamics. Also a high speed of adjustment implies that Nigerian Gross Domestic Product is extremely sensitive to shocks on the government spending in the long-run. An upward trend forecast between 2014 and 2020 is an indication of the continued positive impact and the government retained revenue will exert on the domestic output in the long-run.

基于DDPG的智能反射面辅助无线携能通信系统性能优化

针对智能反射面(IRS, intelligent reflecting surface)辅助的多输入单输出(MISO, multiple input singleoutput)无线携能通信(SWIPT, simultaneous wireless information and power transfer)系统,考虑基站最大发射功率、IRS反射相移矩阵的单位膜约束和能量接收器的最小能量约束,以最大化信息传输速率为目标,联合优化了基站处的波束成形向量和智能反射面的反射波束成形向量。为解决非凸优化问题,提出了一种基于深度强化学习的深度确定性策略梯度(DDPG, deep deterministic policy gradient)算法。仿真结果表明,DDPG算法的平均奖励与学习率有关,在选取合适的学习率的条件下,DDPG算法能获得与传统优化算法相近的平均互信息,但运行时间明显低于传统的非凸优化算法,即使增加天线数和反射单元数,DDPG算法依然可以在较短的时间内收敛。这说明DDPG算法能有效地提高计算效率,更适合实时性要求较高的通信业务。

密度峰值聚类在塔机损伤诊断中的应用研究

建立塔机有限元模型,获取塔机完好状态和各损伤工况的各采集点的动态位移。提出了两种模型建立方法,基于悬臂梁的双输入单输出模型和基于时域数据的动态双输入单输出模型,对基于时域数据的双输入单输出模型首先利用最小二乘法计算参数初值,进一步利用粒子群优化方法进行参数优化,提高了模型精度。以完好工况的塔机数据为基础,建立基于悬臂梁的双输入单输出模型和基于时域数据的双输入单输出模型,计算参数,建立损伤识别模型,用待检状态的位移数值拟合模型,用两种模型计算出的残差方差做损伤因子,利用密度峰值聚类方法对损伤因子进行分析,实现了对塔机的损伤判定和损伤位置的确定。这种基于密度峰值聚类的诊断方法可对塔机微小损伤进行智能诊断和位置确定,该方法只需要塔机完好状态的数据和待检状态的数据即可自动诊断,解决了塔机损伤识别中损伤数据难以获取,因而无法实现智能训练和诊断的问题。

独立充放时序SIDO开关变换器电流型变频控制技术

单电感双输出(single-inductor dual-output,SIDO)开关变换器工作在共享充放时序下存在电感电流纹波大、输出支路间交叉影响严重以及电路参数宽范围变化下控制电路不能正常工作等问题.为此,提出一种独立充放时序电流型变频控制(current-mode variable frequency control,C-VF)技术.首先,具体描述变换器在连续导电模式(continuous conduction mode,CCM)下的工作原理,并推导主电路开环传递函数;进一步构建闭环小信号模型,推导闭环交叉阻抗,详细分析不同输出电压及负载电流下变换器的交叉影响特性;最后,通过仿真和实验进行验证.研究表明:相较于共享充放时序,独立充放时序C-VF CCM SIDO buck变换器减小了交叉影响,改善了负载瞬态响应性能;当两支路负载电压不等时,减轻某一支路负载可以降低该支路的交叉影响;当两支路输出电压相同但负载不同时,重载支路对轻载支路的交叉影响更小.

非最小相位的单电感双输出Buck-Boost变换器的复合控制方法

单电感双输出Buck-Boost (SIDO Buck-Boost)变换器在电感电流连续模式(CCM)下工作存在交叉影响以及非最小相位特性的问题.为了解决上述问题,提出基于储能函数的扩张状态观测器(ESO)的改进非奇异快速终端滑模(NFTSM)和自抗扰控制(ADRC)相结合的控制策略.设计主路控制器,对系统的传递函数进行拟合得到ADRC范式,利用该范式对主路进行解耦控制.设计支路控制器,采用改进型ESO对储能函数进行观测,并将观测值反馈补偿到非奇异快速终端滑模控制律中,达到支路解耦的效果.为了抑制滑模控制的抖振问题,对趋近律进行改进.利用Lyapunov理论证明系统稳定性.基于硬件在环(HIL)实验平台进行实验验证.结果表明,所提控制策略与PI控制策略以及基于ESO的滑模控制策略相比,在超调量和响应时间上具有较好的效果.

一种具有连续输出电流的单开关改进二次型Buck-Boost变换器

针对太阳能光伏发电、燃料电池等需要高增益直流电源的特点,引出了具有连续输出电流的高增益改进二次型Buck-Boost变换器。介绍了该改进变换器的工作原理及稳态特性,另外在多个方面将改进变换器与其他变换器进行了比较,由比较参数显示了改进变换器的优良特性。最后利用PSIM仿真软件建立了改进变换器仿真模型,从降压和升压的角度对改进变换器进行了仿真实验分析,从实验分析的结果来看,改进变换器性能较好,验证了其理论分析的正确性。

基于谐波状态空间的高压直流输电系统SISO阻抗建模及稳定性分析

近年来,电网换相换流器型高压直流输电(line commutated converter based on high voltage direct current,LCC-HVDC)系统的稳定性问题得到广泛关注,多位专家学者建议采用谐波状态空间(harmonic state space,HSS)等线性周期时变建模方法对其分析。然而,HSS不可避免地提高了建模的复杂度与维数,在面对大规模交直流系统时具有局限性。同时,LCC-HVDC包含多类型谐波耦合,各部分耦合对稳定性的影响大小尚未得到充分论证。为此,文中以HSS为底层理论建立LCC-HVDC的耦合阻抗矩阵,揭示高压直流输电系统内部的谐波耦合机理。进一步,通过多频电路等效思想,提出三相系统多维阻抗的降维方法,将耦合阻抗矩阵无损降维成单入单出阻抗,以此分析不同次数的谐波耦合对阻抗特性与稳定性的影响。结果表明,考虑到13次谐波截断可以有效提升高压直流输电系统阻抗模型精度,但对稳定性分析结果的影响小于忽略工况变化、简化逆变侧带来的误差。

考虑工作点时变特性的并网变流器全工作区间稳定性分析

现有工程运行数据显示,并网变流器(grid-connected converter,GCC)的动态特性与工作点密切相关。受新能源出力波动、负载投切等外部因素的影响,变流器工作点呈现随机时变特性。因此,分析整个工作区间中所有工作点的系统稳定性具有重要意义。传统阻抗/导纳分析方法可以有效分析GCC运行于特定工作点时的稳定性,但考虑系统所有可能工作点时则需重复分析,工作量大且难度较高。为解决这一难题,提出一种考虑工作点变量的多元建模方法。将工作点变量引入导纳模型,通过控制环路重构,建立GCC的多变量单输入单输出(single input single output,SISO)模型。所提模型直接包含工作点变量,因此可以有效分析变流器全工作区间动态特性。此外,综合考虑变流器最大传输限制和动态特性,提出一种基于安全运行域的稳定性分析方法,以实现多维工作区间中系统稳定性的直观表征。仿真和实验验证了所提多变量SISO模型和基于安全运行域的分析方法的正确性。所提模型和方法在分析电力电子装置运行极限、指导变流器设计和辅助功率器件发挥极限性能等工程场景中具有广泛应用潜力。

基于分裂-叠加结构的部分功率主动调控型准单级直流变换方法

针对“直流变压器级联PWM变换器”两级式架构中各级变换器均需处理全部负载功率、多级变换效率低的问题,提出了基于分裂-叠加架构的部分功率主动调控型准单级直流变换方法。通过将直流变压器输出分裂为两个端口,使得其中一个端口的功率无需经后级PWM变换器处理而直接传输至负载,等效实现了准单级功率变换,且有效降低了PWM变换器的功率容量和损耗,提高了系统效率。详细分析了分裂-叠加式架构的原理和电路实现方法,深入研究了系统输出电压调节的原理和特性。以其中一个电路为例,详细分析了工作原理、电压调节特性和关键参数设计方法,并通过实验结果验证了所提方案的有效性和正确性。

弱电网下提高并网变流器稳定性的导纳重塑方法

并网变流器接入弱电网易发生振荡问题,基于无源性理论提出一种导纳重塑控制策略来提高系统稳定性能,使并网系统在中低频段不受电网等值阻抗的影响。首先,为了便于构造严格正实的变流器导纳矩阵,将变流器导纳模型分解为两个子系统进行分析,找出可重塑的控制环节;然后,基于正实方法设计了外环重塑矩阵M和内环重塑矩阵N,使并网系统在中低频段内渐进稳定。此外,导纳重塑后的系统是一个对称系统即单输入单输出系统,可方便求取系统的稳定裕度。仿真和实验均验证了所提导纳重塑方法在提高系统稳定性和简化系统稳定性分析的可行性和有效性。

基于瑞利衰落信道的SIMO-HPO-CDSK混沌通信方案及其性能分析

本文提出单输入多输出高速率相位正交CDSK (single-input-multiple-output high-data-rate phase-orthogonality correlation-delay-shift-keying,SIMO-HPO-CDSK),在接收端设置多天线获得分集增益。采用正交载波调制相同时隙的2个比特信息,获得高传输速率且无信号内干扰,瑞利衰落信道下分析性能和仿真。结果表明:SIMO-HPO-CDSK系统误码率随着接收端天线数量增加而下降;在接收方天线数量相同的条件下,由于没有无信号内干扰,与DCSK (differential chaos shift keying),CDSK和高效DCSK (high-efficiency-DCSK)相比,该方案具有出色的误码率性能;与PO-CDSK (phase-orthogonality CDSK)相比,由于同步传输2个比特,该方案频谱利用率提高一倍。

虚假数据注入式攻击下无人水面船舶自适应神经输出反馈轨迹跟踪控制

本文主要研究网络环境下无人水面船舶(Unmanned surface vessels,USVs)遭受虚假数据注入式(False-data-injection,FDI)攻击的跟踪控制问题.其中,内部和外部不确定以及输入饱和约束等实际因素均考虑在设计中.在控制设计过程中,为避免将船舶速度的攻击信号引入闭环系统,采用分类重构思想,构造一种新的神经网络(Neural network,NN)状态观测器,同时重构船舶速度和攻击信号.进一步,在backstepping设计框架下,利用重构的攻击信号补偿USVs运动学通道因虚假数据注入式攻击引起的非匹配不确定项.在动力学设计通道中,利用自适应神经技术和单参数学习法,重构由内部和外部不确定组成的复合不确定部分,进而提出自适应神经输出反馈控制方案.理论分析表明,即便在FDI攻击、内外不确定以及执行器饱和约束的情况下,所提控制方案仍能迫使USVs跟踪给定的参考轨迹.同时,仿真和比较结果证实了所提控制方案的有效性和优越性.

低纹波空间可调高压电源设计

为了满足空间探测载荷(如质谱仪和能量粒子探测器等)对高压电源输出纹波的要求,设计一款小功率、低纹波、最大输出电压为10 kV的可调高压直流电源。设计中使用罗耶架构的逆变器和倍压整流电路,利用反馈回路,使纹波电压峰峰值小于2 V;使用51系列单片机控制电源输出电压,监测电源的工作状态。除在原理设计方面降低输出电压纹波外,还提出其他降低输出电压纹波的措施。测试结果表明,所设计的高压电源具有输出电压稳定可调、纹波低的特点,可以满足空间探测载荷对高压电源的基本性能要求。