A Comparative Study of Epi-up and Epi-Down Bonding of High Power 980 nm Single-Mode Semiconductor Lasers

Epi-up and epi-down bonding of high power 980nm lasers have been studied in terms of bonding process, thermal behavior, optical performances, thermal stress effects and long-term laser reliability. We demonstrated that epi-down bonding can offer lower thermal resistance and improved optical performances without significantly degrading the long-term laser reliability.

High power semiconductor laser array with single-mode emission

The semiconductor laser array with single-mode emission is presented in this paper.The 6-μm-wide ridge waveguides(RWGs)are fabricated to select the lateral mode.Thus the fundamental mode of laser array can be obtained by the RWGs.And the maximum output power of single-mode emission can reach 36 W at an injection current of 43 A,after that,a kink will appear.The slow axis(SA)far-field divergence angle of the unit is 13.65.The beam quality factor M;of the units determined by the second-order moment(SOM)method,is 1.2.This single-mode emission laser array can be used for laser processing.

Fluctuations of Single-Mode Laser Driven by Two Different Kinds of Colored Noise

A single-mode laser with coupling between additive and multiplicative noise terms is investigated when the multiplicative noise and the coupling between two noise terms are colored fluctuations with finite correlation times T1 and T2. Combining the unified colored noise approximation （UCNA） and the functional analysis, the stationary probability distribution （SPD） and the variance of the laser intensity is derived. It is found that the colored nature of multiplicative noise and the coupling strength between two noise terms can affect both the structure and the height of the SPD, while the colored nature of the coupling between two noise terms can only affect the height of the SPD. The multiplicative noise can enhance the intensity fluctuations while the additive noise can reduce the fluctuations in a laser system. Numerical simulations are presented and consistent to the analytical results.

Laser patterning of large-scale perovskite single-crystal-based arrays for single-mode laser displays

Lead halide perovskites have attracted considerable attention as potential candidates for high-performance nano/microlasers,owing to their outstanding optical properties.However,the further development of perovskite microlaser arrays(especially based on polycrystalline thin films)produced by the conventional processing techniques is hindered by the chemical instability and surface roughness of the perovskite structures.Herein,we demonstrate a laser patterning of large-scale,highly crystalline perovskite single-crystal films to fabricate reproducible perovskite single-crystal-based microlaser arrays.Perovskite thin films were directly ablated by femtosecond-laser in multiple low-power cycles at a minimum machining line width of approximately 300 nm to realize high-precision,chemically clean,and repeatable fabrication of microdisk arrays.The surface impurities generated during the process can be washed away to avoid external optical loss due to the robustness of the single-crystal film.Moreover,the high-quality,large-sized perovskite single-crystal films can significantly improve the quality of microcavities,thereby realizing a perovskite microdisk laser with narrow linewidth(0.09 nm)and low threshold(5.1µJ/cm2).Benefiting from the novel laser patterning method and the large-sized perovskite single-crystal films,a high power and high color purity laser display with single-mode microlasers as pixels was successfully fabricated.Thus,this study may offer a potential platform for mass-scale and reproducible fabrication of microlaser arrays,and further facilitate the development of highly integrated applications based on perovskite materials.

Stochastic Resonance in Linear Region of a Single-Mode Laser: Effects of Amplitude Modulation of Signal

A single-mode laser noise model driven by quadratic colored pump noise and amplitude modulation signal is proposed. The real and imaginary parts of the pump noise are assumed to be cross-correlation. The effect of cross- correlation of noise and amplitude modulation of signal on laser statistical properties is studied by using the linearized approximation. The analytic expression of signal-to-noise ratio （SNR） is calculated. It is found that the phenomena of stochastic resonance （SR） respectively exist in the curves of the SNR versus the noise cross-correlation coefficient λ and the SNR versus the pump parameter a, as well as the SNR versus the signal frequency ω in our model. It is shown that there are three different typies of SR in the model： the conventional form of SR, the SR in the broad sense, and the bona fide SR.

Stochastic resonance in a single-mode laser driven by frequency modulated signal and coloured noises

By adding frequency modulated signals to the intensity equation of gain noise model of the single-mode laser driven by two coloured noises which are correlated, this paper uses the linear approximation method to calculate the power spectrum and signal-to-noise ratio （SNR） of the laser intensity. The results show that the SNR appears typical stochastic resonance with the variation of intensity of the pump noise and quantum noise. As the amplitude of a modulated signal has effects on the SNR, it shows suppression, monotone increasing, stochastic resonance, and multiple stochastic resonance with the variation of the frequency of a carrier signal and modulated signal.

Time-Delayed Feedback Control in a Single-Mode Laser System

The effects of time-delayed feedback control in a single-mode laser system is investigated.Using the smalltime delay approximation,the analytic expression of the stationary probability distribution function of the laser field isobtained.The mean,normalized variance and skewness of the steady-state laser intensity are calculated.It is found thatthe time-delayed feedback control can suppress the intensity fluctuation of the laser system.The numerical simulationsare in good agreement with the approximate analytic results.

Stationary properties of a single-mode laser system with non-Gaussian and Gaussian noise

A single-mode laser system with non-Gaussian and Gaussian noise is investigated. The stationary mean value and the normalized variance of the laser intensity are numerically calculated under the condition that the stationary probability distribution function （SPDF） is derived. The SPDF as a function of the laser intensity exhibits a maximum, The maximum becomes smaller with the increase of the correlation intensity or the non-Gaussian parameter, where the later is a measure of the deviation from the Gaussian characteristic. The maximum becomes larger as the correlation time increases. The laser intensity stationary mean value decreases with the increase of the correlation intensity or the non-Gaussian parameter while increases with the correlation time increasing. The laser intensity normalized variance increases with the increase of the correlation intensity or the non-Gaussian parameter while decreases as the correlation time increases.

The statistical fluctuation of a single-mode laser system driven by coloured pump noise with signal modulation and the quantum noise with cross-correlation between its real and imaginary parts

Using the linear approximation method, this paper studies the statistical property of a single-mode laser driven by both coloured pump noise with signal modulation and the quantum noise with cross-correlation between its real and imaginary parts, and calculates the steady-state mean normalized intensity fluctuation and intensity correlation time. It analyses the influences of the modulation signal, the net gain coefficient, the noise and its correlation form on the statistical fluctuation of the laser system respectively. It is found that the coloured pump noise modulated by the signal has a great suppressing action on the statistical fluctuation of the laser system; the pump noise self-correlation time and the specific frequency of modulation signal have the result that the statistical fluctuation tends to zero. Furthermore, the ＇colour＇ correlation of pump noise has much influences on the statistical fluctuation of the laser system. Increasing the intensity of pump noise will augment the statistical fluctuation of the laser system, but the intensity of quantum noise and the coefficient of cross-correlation between its real and imaginary parts have less influence on the statistical fluctuation of the laser system. Therefore, from the conclusions of this paper the statistical property can be known and a theoretical basis for steady operation and output of the laser system can be provided.

Single-mode GaSb-based laterally coupled distributed-feedback laser for CO_(2)gas detection

We report on a GaSb-based laterally coupled distributed feedback(LC-DFB)laser with Cr gratings operating at 2004 nm for CO_(2)detection application.Butterfly packaged with single-mode fiber pigtailed,the laser diode operates in the continuous-wave mode in a temperature range from-10℃to 60℃,with a maximum output power of 2 mW and a maximum side-mode suppression ratio over 30 dB.Wavelength-modulated absorption spectroscopy of CO_(2)demonstrates the applicability of the LC-DFB laser to tunable diode laser absorption spectroscopy.Furthermore,the diode junction temperature,which is measured by using the wavelength shift method,exhibits a maximum value of 17℃in the single-mode operation range.

Influence of Signal and Noise on Statistical Fluctuation of Single-Mode Laser System

On the basis of calculating the steady-state mean normalized intensity fluctuation of a signal-mode laser system driven by both colored pump noise with signal modulation and the quantum noise with cross-correlation between its real and imaginary parts, we analyze the influence of modulation signal, noise, and its correlation form on the statistical fluctuation of the laser system. We have found that when the amplitude of modulation signal weakens and its frequency quickens, the statistical fluctuation will reduce rapidly. The by reducing the intensity of pump noise and quantum noise. statistical fluctuation of the laser system can be restrained Moreover, with prolonging of colored cross-correlation time, the statistical fluctuation of laser system experiences a repeated changing process, that is, from decreasing to augmenting, then to decreasing, and finally to augmenting again. With the decreasing of the value of cross-correlation coe~cient, the statistical fluctuation will decrease too. When the cross-correlation form between the real part and imaginary part of quantum noise is zero correlation, the statistical fluctuation of laser system has a minimum. Compared with the influence of intensity of pump noise, the influence of intensity of quantum noise on the statistical fluctuation is smaller.

Effecfs of Cross-Correlation Between Real Noise in Transient Process of Single-Mode and Imaginary Parts of Colored Pump Laser

A two-dimensional single-mode laser model with cross-correlation between the real and imaginary parts of the colored quadric pump noise is investigated. A novel laser amplitude Langevin equation is obtained, in which the cross-correlation λp between the real and imaginary parts of the pump noise appears. The mean, variance, and skewness of first-passage-time are calculated. It is shown that the mean, variance, and skewness of first-passage-time are strongly affected by λp.

Modeling analysis and optimization design of the thermostatical control system of laser instrument of the semiconductor

Influence produced by the heat effect at work of the laser instrument crystal of the semiconductor, the text designs a kind of temperature control system to the crystal of the laser instrument, using the thought and method of the classical control theory to analyze this temperature control system, and establishes mathematics model. According to mathematics model the text demonstrated the system at S field and time- area, and proposed optimizing basis to the total mark of proportion and differential parameter to con- troller PID, thus proposed a kind of temperature control scheme. And the thermostatically system is simulated by MATLAB.

Measurement of Cavity Loss and Quasi-Fermi-Level Separation for Fabry-Pérot Semiconductor Lasers

A fitting process is used to measure the cavity loss and the quasi Fermi level separation for Fabry Pérot semiconductor lasers.From the amplified spontaneous emission (ASE) spectrum,the gain spectrum and single pass ASE obtained by the Cassidy method are applied in the fitting process.For a 1550nm quantum well InGaAsP ridge waveguide laser,the cavity loss of about ～24cm -1 is obtained.

Gain Switch of an AlGaInP Red Light Semiconductor Laser Diode

We solve the single mode coupled rate equations by computer,simulate the behavior of a gain switch of an AlGaInP red light semiconductor laser diode,and find the characteristic of FWHM of pulses changing with the amplitude of modulation signal, the bias current, and the modulated frequency. On this basis, we conduct experiments. The experiment results accord with the simulations well.

Tunable and broadband microwave frequency combs based on a semiconductor laser with incoherent optical feedback

Based on a semiconductor laser （SL） with incoherent optical feedback, a novel all-optical scheme for generating tunable and broadband microwave frequency combs （MFCs） is proposed and investigated numerically. The results show that, under suitable operation parameters, the SL with incoherent optical feedback can be driven to operate at a regular pulsing state, and the generated MFCs have bandwidths broader than 40 GHz within a 10 dB amplitude variation. For a fixed bias current, the line spacing （or repetition frequency） of the MFCs can be easily tuned by varying the feedback delay time and the feedback strength, and the tuning range of the line spacing increases with the increase in the bias current. The linewidth of the MFCs is sensitive to the variation of the feedback delay time and the feedback strength, and a linewidth of tens of KHz can be achieved through finely adjusting the feedback delay time and the feedback strength. In addition, mappings of amplitude variation, repetition frequency, and linewidth of MFCs in the parameter space of the feedback delay time and the feedback strength are presented.

Chaos synchronization in injection-locked semiconductor lasers with optical feedback

Based on the rate equations, we have investigated three types of chaos synchronizations in injection-locked semiconductor lasers with optical feedback. Numerical simulation shows that the synchronization can be realized by the symmetric or asymmetric laser systems. Also, the influence of parameter mismatches on chaos synchronization is investigated, and the results imply that these two lasers can achieve good synchronization, with smaller tolerance of parameter mismatch existing.

Graded doping low internal loss 1060-nm InGaAs/AlGaAs quantum well semiconductor lasers

Internal loss is a key internal parameter for high power 1060-nm InGaAs/A1GaAs semiconductor laser. In this paper, we discuss the origin of internal loss of 1060-nm InGaAs/GaAs quantum welt （QW） AIGaAs separate confinement het- erostructure semiconductor laser, and the method to reduce internal loss. By light doping the n-cladding layer, and stepwise doping the p-cladding layer combined with the expanded waveguide layer, a broad area laser with internal loss of 1/cm is designed and fabricated. Ridge waveguide laser with an output power of 350 mW is obtained. The threshold current and slope efficiency near the threshold current are 20 mA and 0.8 W/A, respectively.

Flexible control of semiconductor laser with frequency tunable modulation transfer spectroscopy

We introduce a new method of simultaneously implementing frequency stabilization and frequency shift for semiconductor lasers. We name this method the frequency tunable modulation transfer spectroscopy （FTMTS）. To realize a stable output of 780 nm semiconductor laser, an FTMTS optical heterodyne frequency stabilization system is constructed. Before entering into the frequency stabilization system, the probe laser passes through an acousto-optical modulator （AOM） twice in advance to achieve tunable frequency while keeping the light path stable. According to the experimental results, the frequency changes from 120 MHz to 190 MHz after the double-pass AOM, and the intensity of laser entering into the system is greatly changed, but there is almost no change in the error signal of the FTMTS spectrum. Using this signal to lock the laser frequency, we can ensure that the frequency of the laser changes with the amount of AOM shift. Therefore, the magneto-optical trap （MOT）-molasses process can be implemented smoothly.

Stable single-mode operation of 894.6 nm VCSEL at high temperatures for Cs atomic sensing

In this paper, stable single-mode operation at high temperatures is produced by the surface-relief-integrated vertical cavity surface emitting laser（VCSEL）. The gain-cavity mode detuning technique is employed to realize high operating temperatures for the VCSEL. The surface relief is etched in the centre of the top side as a mode discriminator for the fundamental mode output, and the threshold current minimum is 1.94 mA at high temperatures by the gain-cavity mode detuning technique. Maximum single-fundamental-mode output power of 0.45 mW at 80℃ is obtained, and the side mode suppression ratios（SMSRs） are more than 30 dB with increasing temperature and current, respectively.