Analysis for the Deployment of Single-Point Mooring Buoy System Based on Multi-Body Dynamics Method

Deployment of buoy systems is one of the most important procedures for the operation of buoy system. In the present study, a single-point mooring buoy system which contains surface buoy, cable segments with components, anchor and so on is modeled by applying multi-body dynamics method. The motion equations are developed in discrete node description and fully Cartesian coordinates. Then numerical method is used to solve the ordinary differential equations and dynamics simulations are achieved while anchor is casting from board. The trajectories and velocities of different nodes without current and with current in buoy system are obtained. The transient tension force of each part of the cable is analyzed in the process of deployment. Numerical results indicate that the transient payload increases to a peak value when the anchor is touching the seabed and the maximum tension force will vary with different floating configuration. This work is helpful for design and deployment planning of buoy system.

Lateral Vibration Behavior Analysis and TLD Vibration Absorption Design of the Soft Yoke Single-Point Mooring System

Mooring system is the key equipment of FPSO safe operation. The soft yoke mooring system is regarded as one of the best shallow water mooring strategies and widely applied to the oil exploitation in the Bohai Bay in China and the Gulf of Mexico. Based on the analysis of numerous monitoring data obtained by the prototype monitoring system of one FPSO in the Bohai Bay, the on-site lateral vibration behaviors found on the site of the soft yoke subject to wave load were analyzed. ADAMS simulation and model experiment were utilized to analyze the soft yoke lateral vibration and it was determined that lateral vibration was resonance behaviors caused by wave excitation. On the basis of the soft yoke longitudinal restoring force being guaranteed, a TLD-based vibration damper system was constructed and the vibration reduction experiments with multi-tank space and multi-load conditions were developed. The experimental results demonstrated that the proposed TLD vibration reduction system can effectively reduce lateral vibration of soft yoke structures.

Current observation and analysis based on mooring systems in the Andaman Sea

The basic structure and intraseasonal evolution of currents in the southeastern Andaman Sea was analyzed based on data collected in 2017 from two subsurface moorings(C1 and C5).Periodic variation in the upper ocean currents of the Andaman Sea was investigated by combining observational and satellite data.Mooring observations show that rapid changes of current speed and direction occurred in May and June,with a significant increase in current velocity at the C1 mooring.In the second half of the year,southward flow dominated at the C1 mooring,and alternating northward and southward flows were evident at the C5 mooring during the same period but the northward flow prevailed in boreal winter.In addition,analysis of the power spectra of the upper currents revealed that the tidal period at both moorings is primarily semidiurnal with weaker energy than that of the low-frequency currents.The upper ocean currents at the C1 and C5 moorings exhibited intraseasonal variation of 30-60 d and 120 d,while the zonal current at the C1 mooring exhibited a notable period of approximately 180 d.Further analysis indicated that the variability of currents in the Andaman Sea is influenced primarily by equatorial Kelvin waves and Rossby wave packets.Moreover,our results suggest that equatorial Kelvin waves from the eastern Indian Ocean entered the Andaman Sea in the form of Wyrtki Jets and propagated primarily along two distinct pathways during the observation period.In addition to coastal boundary Kelvin waves,it was found that a branch of the Wyrtki Jet that directly enters the Andaman Sea and flows northward along the slope of the continental shelf,and reflected Rossby wave packets by topography.

Intraseasonal variability of the Kuroshio observed via mooring at 18°N

Insufficient observations near the origin of the Kuroshio have led to incomplete understanding of the intraseasonal variability(ISV)of the Kuroshio.Direct measurements of the Kuroshio velocity were performed with an array of three profiler moorings(122.7°E,123°E,and 123.3°E)along 18°N from January 2018 to February 2020.The ISV of the Kuroshio at 18°N was investigated based on a combination of mooring observations and global high-resolution HYbrid Coordinate Ocean Model reanalysis data.The estimated time-averaged transport in the upper 350 m across the observation transect was 6.5±2.6 Sv(1.0 Sv=10^(6)m^(3)/s).Two significant ISV peaks at 50-60 and~100 d were recognized in the power spectra of the meridional velocity and transport.Further analysis indicated that the ISV at 50-60 d was caused by westward-propagating eddies at average propagation speed of~13 cm/s and wavelength of~635 km.Another ISV peak at~100 d was mainly caused by northward-propagating eddies generated in the North Equatorial Current region.Further investigation indicated that the ISV of the Kuroshio at 18°N is dominated by meridional transport,rather than by the zonal migration of the Kuroshio main axis.Our findings provide a better understanding of the ISV of the Kuroshio east of Luzon Island.

Orthogonal Frequency Division Multiplexing Adaptive Technology for Multinode Users of Seawater Channel Based on Inductively Coupled Mooring Chain

As an important part of buoy-type ocean monitoring systems,the inductively coupled mooring chain solves the problem of data cotransmission through the multinode sensors that it carries,which is significant for the rapid acquisition of fish,hydrology,and other information.This paper is based on a seawater channel transmission model with a depth of 300 m and a bandwidth of 2 MHz.An orthogonal frequency division multiplexing(OFDM)technology is used to overcome the multipath effect of signal transmission on a seawater medium.The adaptive technology is integrated into the OFDM,and an improved joint subcarrier and bit power allocation algorithm is proposed.This algorithm solves the problem of dynamic subcarrier allocation during the cotransmission of underwater multinode user data in seawater channels.The results show that the algorithm complexity can be reduced by 0.18126×10^(-2)s during one complete OFDM system data transmission by the improved greedy algorithm,and a total of 216 bits are transmitted by the OFDM.The normalized channel capacity can be improved by 0.012 bit s^(-1)Hz^(-1).At the bit error ratio(BER)of 10^(-3),the BER performance can be improved by approximately 6 d B.When the numbers of users are 4 and 8,the improved algorithm increases the channel capacity,and the higher the number of users,the more evident the channel capacity improvement effect is.The results of this paper have an important reference value for enhancing the transmission performance of inductively coupled mooring chain underwater multinode data.

Study on the Characteristics of A New Hybrid Mooring System for DualPlatform Joint Operations

As the sustainable exploitation of marine resources develops,dual-platform joint operation has caught increasing attention.Dual-platform joint operation requires smaller relative motion between the two sub-platforms,which is normally difficult to be satisfied by the traditional mooring system.Therefore,a new hybrid mooring system is developed and studied in this article.To ensure safety during platform movements,both the number of anchor chains and the relative motion between the two sub-platforms are reduced in the new hybrid mooring system.By performing numerical simulations based on three-dimensional potential flow theory in AQWA and physical experiments,the performances of both the new hybrid and traditional mooring systems under two different wave conditions(i.e.,working wave and freak wave conditions) are systematically investigated.Regarding the new hybrid mooring system,the relative stability between the two sub-platforms of the new system is better,and the platforms can restore stability faster when affected by freak waves.

Motion simulation of moorings using optimized LSTM neural network

Mooring arrays have been widely deployed in sustained ocean observation in high resolution to measure finer dynamic features of marine phenomena.However,the irregular posture changes and nonlinear response of moorings under the effect of ocean currents face huge challenges for the deployment of mooring arrays,which may cause the deviations of measurements and yield a vacuum of observation in the upper ocean.We developed a data-driven mooring simulation model based on LSTM(long short-term memory)neural network,coupling the ocean current with position data from moorings to predict the motion of moorings,including single-step output prediction and multi-step prediction.Based on the predictive information,the formation of the mooring array can be adjusted to improve the accuracy and integrity of measurements.Moreover,we proposed the cuckoo search(CS)optimization algorithm to tune the parameters of LSTM,which improves the robustness and generalization of the model.We utilize the datasets observed from moorings anchored in the Kuroshio Extension region to train and validate the simulation model.The experimental results demonstrate that the model can remarkably improve prediction accuracy and yield stable performance.Moreover,compared with other optimization algorithms,CS is more efficient and performs better in simulating the motion of moorings.

Fully Coupled Effects of Hull,Mooring and Risers Model in Time Domain Based on An Innovative Deep Draft Multi-Spar

The coupled hull, mooring and riser analysis techniques in time domain are widely recognized as the unique approach to predict the accurate global motions. However, these complex issues have not been perfectly solved due to a large number of nonlinear factors, e.g. forces nonlinearity, mooring nonlinearity, motion nonlinearity and so on. This paper investigates the coupled effects through the numerical uncoupled model, mooring coupled model and fully coupled model accounting mooring and risers based on a novel deep draft multi-spar which is especially designed for deepwater in 2009. The numerical static-offset, free-decay, wind-action tests are executed, and finally three hours simulations are conducted under 100-year return period of GOM conditions involving wave, wind and current actions. The damping contributions, response characteristics and mooring line tensions are emphatically studied.

Static and Dynamic Analysis of Mooring Lines by Nonlinear Finite Element Method

This study has focused on developing numerical procedures for the static and dynamic nonlinear analysis of mooring lines. A geometrically nonlinear finite element method using isoparametric cable element with two nodes is briefly presented on the basis of the total Lagrangian formulation. The static and dynamic equilibrium equations of mooring lines are established. An incremental-iterative method is used to determine the initial static equilibrium state of cable systems under the action of self weights, buoyancy and current. Also the Newmark method is used for dynamic nonlinear analysis of ocean cables. Numerical examples are presented to validate the present numerical method, and examine the effect of various parameters.

Study on A New Mooring System Integrating Catenary with Taut Mooring

Analyzed are the merits and demerits of catenary mooring system and taut mooring system, which are commonly used nowadays. As falling somewhere between these two systems, a new mooring system integrating catenary with taut mooring is proposed. In order to expound and prove the advantages of this new system, the motion performance of a semi-submersible platform is simulated by employing full time domain coupled analysis method. A comparison of the result of new mooting system with that of taut mooring system shows that the movement of the platform using the new type mooting system is smaller than that using the taut mooring system, which ensures a better working condition. Furthermore, the new mooring system is also compatible with the characteristics of catenary mooting system, which eliminates the requirement of anti-uplift capacity of the anchors.

Fatigue Analysis of the Taut-Wire Mooring System Applied for Deep Waters

Precisely predicting the fatigue life of taut-wire mooring systems has become an interesting and important problem for scientists and engineers since there are still difficulties in the inspection and maintenance of mooring lines in a rough sea environment especially in deep waters. In this paper, a comprehensive fatigue analysis is performed for a polyester taut-wire mooring system of an FPSO based on the time domain dynamic theory, rainflow cycle counting method and linear damage accumulation rule of Palmgren-Miner. Three influential factors in the fatigue analysis including the pre-tension, dynamic stiffness and T-N curve are investigated in detail. Two polyester T-N curves, one is from the DNV- 0S-E301 and the other is from the API-RP-2SM, are adopted in the calculation. The fatigue analysis of the mooting system after one-line failure is also carried out. The calculation results indicate that the fatigue life is significantly affected by the T-N curve. The fatigue life decreases with increasing pre-tension, and is largely reduced if taking into account the dynamic stiffness caused by cyclic loading. The analysis also proves that one-line failure has remarkable effects on the fatigue lives of other mooting lines. The present parametric and comparative study is believed to be meaningful to further understanding of the taut-wire mooting system for deepwater applications.

Sensitivity Analysis of Air Gap Motion with Respect to Wind Load and Mooring System for Semi-Submersible Platform Design

A design of semi-submersible platform is mainly based on the extreme response analysis due to the forces experienced by the components during lifetime. The external loads can induce the extreme air gap response and potential deck impact to the semi-submersible platform. It is important to predict air gap response of platforms accurately in order to check the strength of local structures which withstand the wave slamming due to negative air gap. The wind load cannot be simulated easily by model test in towing tank whereas it can be simulated accurately in wind tunnel test. Furthermore, full scale simulation of the mooring system in model test is still a tuffwork especially the stiffness of the mooring system. Owing to the above mentioned problem, the model test results are not accurate enough for air gap evaluation. The aim of this paper is to present sensitivity analysis results of air gap motion with respect to the mooring system and wind load for the design of semi-submersible platform. Though the model test results are not suitable for the direct evaluation of air gap, they can be used as a good basis for tuning the radiation damping and viscous drag in numerical simulation. In the presented design example, a numerical model is tuned and validated by ANSYS AQWA based on the model test results with a simple 4 line symmetrical horizontal soft mooring system. According to the tuned numerical model, sensitivity analysis studies of air gap motion with respect to the mooring system and wind load are performed in time domain. Three mooring systems and five simulation cases about the presented platform are simulated based on the results of wind tunnel tests and sea-keeping tests. The sensitivity analysis results are valuable for the floating platform design.

Risk Assessment on A Pipeline Passing Through A Ship Mooring Area

It is very common that a submarine pipeline has to pass through a ship mooring area near a harbor zone in the Bohai Bay, China. The risk assessment of accidental events induced by the potential anchoring ships is carried out, which will lead to external interference with the pipeline. A procedure to calculate the probability for the anchoring activity in the ship mooring area to damage the underlying pipeline is proposed. The adopted methodology is based on the recommendations suggested by the DNV Codes. The same philosophy is also applied to estimate the damage probability that is concerned with sinking ships.

Mooring System Optimisation and Effect of Different Line Design Variables on Motions of Truss Spar Platforms in Intact and Damaged Conditions

This paper presents the effect of mooring diameters, fairlead slopes and pretensions on the dynamic responses of a truss spar platform in intact and damaged line conditions. The platform is modelled as a rigid body with three degrees-of-freedom and its motions are analysed in time-domain using the implicit Newmark Beta technique. The mooring restoring force-excursion relationship is evaluated using quasi-static approach. MATLAB codes DATSpar and QSAML, are developed to compute the dynamic responses of truss spar platform and to determine the mooring system stiffness. To eliminate the conventional trial and error approach in the mooring system design, a numerical tool is also developed and described in this paper for optimising the mooring configuration. It has a graphical user interface and includes regrouping particle swarm optimisation technique combined with DATSpar and QSAML. A case study of truss spar platform with ten mooring lines is analysed using this numerical tool. The results show that optimum mooring system design benefits the oil and gas industry to economise the project cost in terms of material, weight, structural load onto the platform as well as manpower requirements. This tool is useful especially for the preliminary design of truss spar platforms and its mooring system.

Impact Analysis of Air Gap Motion with Respect to Parameters of Mooring System for Floating Platform

In this paper, the impact analysis of air gap concerning the parameters of mooring system for the semi-submersible platform is conducted. It is challenging to simulate the wave, current and wind loads of a platform based on a model test simultaneously. Furthermore, the dynamic equivalence between the truncated and full-depth mooring system is still a tuff work. However, the wind and current loads can be tested accurately in wind tunnel model. Furthermore, the wave can be simulated accurately in wave tank test. The full-scale mooring system and the all environment loads can be simulated accurately by using the numerical model based on the model tests simultaneously. In this paper, the air gap response of a floating platform is calculated based on the results of tunnel test and wave tank. Meanwhile, full-scale mooring system, the wind, wave and current load can be considered simultaneously. In addition, a numerical model of the platform is tuned and validated by ANSYS AQWA according to the model test results. With the support of the tuned numerical model, seventeen simulation cases about the presented platform are considered to study the wave, wind, and current loads simultaneously. Then, the impact analysis studies of air gap motion regarding the length, elasticity, and type of the mooring line are performed in the time domain under the beam wave, head wave, and oblique wave conditions.

Dynamics of Large-Truncated Mooring Systems Coupled with A Catenary Moored Semi-Submersible

With the floating structures pushing their activities to the ultra-deep water, model tests have presented a challenge due to the limitation of the existing wave basins. Therefore, the concept of truncated mooring system is implemented to replace the full depth mooring system in the model tests, which aims to have the same dynamic responses as the full depth system. The truncated mooring system plays such a significant role that extra attention should be paid to the mooring systems with large truncation factor. Three different types of large truncation factor mooring system are being employed in the simulations, including the homogenously truncated mooring system, non-homogenously truncated mooring system and simplified truncated mooring system. A catenary moored semi-submersible operating at 1000 m water depth is presented. In addition, truncated mooring systems are proposed at the truncated water depth of 200 m. In order to explore the applicability of these truncated mooring systems, numerical simulations of the platform’s surge free decay interacting with three different styles of truncated mooring systems are studied in calm water. Furthermore, the mooring-induced damping of the truncated mooring systems is simulated in the regular wave. Finally, the platform motion responses and mooring line dynamics are simulated in irregular wave. All these simulations are implemented by employing full time domain coupled dynamic analysis, and the results are compared with those of the full depth simulations in the same cases. The results show that the mooring-induced damping plays a significant role in platform motion responses, and all truncated mooring systems are suitable for model tests with appropriate truncated mooring line diameters. However, a large diameter is needed for simplified truncated mooring lines. The suggestions are given to the selection of truncated mooring system for different situations as well as to the truncated mooring design criteria.

Mooring System of Ocean Turbulence Observation Based on Submerged Buoy

A comparison experiment has been taken in the Kiaochow Bay between a newly designed mooring turbulence observation instrument （MTOI） and microstructure profiler MSS60 made by Sea ＆ Sun. The whole observing system is based on a submerged buoy, in which the turbulence observation instrument is embedded, with a streamline-shape floating body, which is made of buoyancy material of glass microsphere. For the movement of seawater and the cable shaking strongly anytime influence the behaviors of the floating body, the accelerate sensors are used for the vibration measurement in the instrument together with the shear probe sensor. Both the vibration data and the shear data are acquired by the instrument at the same time. During data processing, the vibration signals can be removed and leave the shear data which we really need. In order to prove the reliability of the new turbulence instrument MTOI, a comparison experiment was designed. The measuring conditions are the same both in time and space. By this way, the two groups of data are comparable. In this paper, the conclusion gives a good similarity of 0.93 for the two groups of shear data in dissipation rate. The processing of the data acquired by MTOI is based on the cross-spectrum analysis, and the dissipation rate of it matches the Nasmyth spectrum well.

Theoretical Model and Dynamic Analysis of Soft Yoke Mooring System

As a popular solution for mooring an FPSO （Floating Production, Storage and Offloading） permanently in shallow water, the soft yoke mooring system has been widely used in ocean oil production activities in the Bohai Bay of China. In order to simulate the interaction mechanism and conduct dynamic analysis of the soft yoke mooring system, a theoretical model with basic dynamic equations is established. A numerical iteration algorithm based on error estimation is developed to solve the equations and calculate the dynanfic response of the mooring system due to FPSO motions. Validation is conducted by wave basin experimentation. It is shown that the numerical simulation takes only a few iteration times and the final errors are small. Furthermore, the calculated results of both the static and dynamic responses agree well with those ones obtained by the model test. It indicates that the efficiency, the precision, the reliability and the validity of the developed numerical algorithm and program are rather good. It is proposed to develop a real-time monitoring system to further monitor the dynamic performance of the FPSO with a soft yoke mooring system under various real sea environments.

Investigation of Motion of Two Hinged Bodies Moored by Mooring Lines in Waves

In this paper, the motions are studied of a multi-body which is composed of two plates hinged together and moored by eight mooring lines in regular waves. The experimental results are compared with computational results. The linear potential theory and the perturbation method are combined to study this complicated system. The former is used to calculate the wave forces acting on the plates and the motion responses of them, while the latter is used to describe the dynamic character of the eight mooring lines coupled with the two hinged plates. Some response results of each plate are presented and comparisons between calculated results and experimental data are given. All the calculations are confined to regular beam waves.

Dynamic Analysis of Semi-Submersible Production Platform Under the Failure of Mooring Lines

This paper quantitatively studies the transient dynamic response of a semi-submersible production platform with the loss of one or several positioning mooring lines.A semi-submersible platform,production risers,and positioning mooring lines are all included in the numerical simulation.Increased motion of the semi-submersible platform,tension variation of the remaining mooring lines/risers and the risk of mooring line or riser clashing are all investigated through fully coupled time-domain analysis.Combined environmental loads are selected from irregular waves and the steady current varying from very rough to extreme sea conditions.Three dimension radiation/diffraction theories and Morison’s equation are applied to calculate first-order wave force and second-order mean drift force of floating semi-submersible platform.Nonlinear time-domain finite element methods are employed to analyze the behavior of mooring lines and risers.Results show that the failure of mooring lines seriously reduce the platform’s stability performance.The tension of the rest lines is also increased accordingly.Remaining lines which are closer to the failed lines will have larger tension increase to compensate.Line-Line distance provides practical information for the risk of clashing investigation.