Experimental study on failure characteristics of single-sided unloading rock under different intermediate principal stress conditions

Investigation of unloading rock failure under differentσ_(2)facilitates the control mechanism of excavation surrounding rock.This study focused on single-sided unloading tests of granite specimens under true triaxial conditions.The strength and failure characteristics were studied with micro-camera and acoustic emission(AE)monitoring.Furthermore,the choice of test path and the effect ofσ_(2)on fracture of unloading rock were discussed.Results show that the increasedσ_(2)can strengthen the stability of single-sided unloading rock.After unloading,the rock’s free surface underwent five phases,namely,inoculation,particle ejection,buckling rupture,stable failure,and unstable rockburst phases.Moreover,atσ_(2)≤30 MPa,the b value shows the following variation tendency:rising,dropping,significant fluctuation,and dropping,with dispersed damages signal.Atσ_(2)≥40 MPa,the tendency shows:a rise,a decrease,a slight fluctuation,and final drop,with concentrated damages signal.After unloading,AE energy is mainly concentrated in the micro-energy range.With the increasedσ_(2),the micro-energy ratio rises.In contrast,low,medium and large energy ratios drop gradually.The increased tensile fractures and decreased shear fractures indicate that the failure mode of the unloading rock gradually changes from tensile-shear mode to tensile-split one.The fractional dimension of the rock fragments first increases and then decreases with an inflection point at 20 MPa.The distribution of SIF on the planes changes asσ_(2)increases,resulting in strengthening and then weakening of the rock bearing capacity.

Characteristics Investigation of Single-Sided Ironless PMLSM Based on Halbach Array for Medium-Speed Maglev Train

This paper investigates characteristics of ironless permanent magnet linear synchronous motor(PMLSM)based on Halbach array used for medium-speed(200km/h)maglev train.Long primary ironless coil is laid in the middle of track and the Halbach permanent magnet array is attached to the bottom of each bogie as a source of traction,U-shape electromagnets at the both sides of the train for levitation.Two dimensional analytical model of single-sided ironless PMLSM based on Halbach array is established,using linear overlay method,the no-load air gap magnetic field is calculated firstly,winding current density distribution is obtained for calculating the characteristics of thrust and normal force against power angle,including force characteristics with equal and unequal pole pitch,the influence of steel sleeper,etc.Besides,the mathematical model for this type motor is built by 3D finite element method,the traction characteristics of medium-speed maglev under maximum speed 200km/h are calculated.The characteristics of this type motor are satisfactory owing to there is no detent force in the motor and thrust force reach maximum meanwhile normal force can be eliminated.Calculation method is verified by comparing finite element results,experimental result on a 200kW type motor further validates the accuracy of calculation and some important conclusions are obtained.

Adaptive current compensation with nonlinear disturbance observer for single-sided linear induction motor considering dynamic eddy-effect

An adaptive current compensation control for a single-sided linear induction motor(SLIM) with nonlinear disturbance observer was developed. First, to maintain t-axis secondary component flux constant with consideration of the specially dynamic eddy-effect(DEE) of the SLIM, a instantaneously tracing compensation of m-axis current component was analyzed. Second,adaptive current compensation based on Taylor-discretization algorithm was proposed. Third, an effective kind of nonlinear disturbance observer(NDOB) was employed to estimate and compensate the undesired load vibrations, then the robustness of the control system could be guaranteed. Experimental verification of the feasibility of the proposed method for an SLIM control system was performed, and it showed that the proposed adaptive compensation scheme with NDOB could significantly promote speed dynamical response and minimize speed ripple under the conditions of external load coupled vibrations and unavoidable feedback control variables measured errors, i.e., current and speed.

Measurement of thermal conductivity of materials using single-side TPS technique

Based on the traditional measurement theory of transient plane source (TPS) technique, single-side TPS method is proposed for measuring the thermal conductivity of single specimen. The problem of transient heat conduction in a semi-infinite boundary condition is studied and the theoretical formula of single-side TPS method is deduced. During the measurement, the influence of the probe heat capacity on the results is analyzed and the corresponding mathematical compensation model is established, and a series of experiments on different materials are conducted by hot disk probe at normal temperature and pressure. The results show that the relative error with the single-side TPS method is less than 5% and the relative standard deviation is no greater than 3%. This method has high accuracy and good reproducibility, which provides a feasible measuring method for single material that does not meet the requirements of the standard TPS theory.

Experimental Investigation of Defects Inspection for FRP Pipeline based on Single-side NMR

The fiberglass reinforced plastic （FRP） pipelines have been used widely in oil-gas gathering and transportation. The defects of FRP pipelines would increase with the extension of service time. However, it is very difficult to detect the defects of FRP pipelines on-spot quickly. In this paper, a new method detecting defects for FRP pipes has been provided based on the NMR. The proton density distributions have been obtained at different depth of FRP components using single-side NMR. The experimental results show that there is a significant change of proton density distribution at the location of defects. And, these results would be useful for defects inspection of composite material component.

Cost Comparison of Different Types of Formworks

Formwork is the temporary moulds in the construction which is fabricated based on the drawing and design of the structure and into which the concrete is poured to form the required structure.Formwork is an essential part of the construction as it has been used by the Romans.The formworks must be strong enough to withstand all types of loads.The joint must be in proper condition to avoid any kind of leakages.The materials used for the formworks should be economical,easily available and durable.The formworks can be made up of different materials such as plywood,steel,aluminum,composite material,etc.In steel formwork the plates used for the slab support are made up of galvanized steel and these are fabricated as per the requirements.Aluminum plates are used in the aluminum framework along with the other components made up of aluminum.The selection of a suitable framework is important in any project because it bears about 25%to 30%cost of the total cost of construction.In the present study,different types of formworks such as steel,plywood and aluminum were studied in a project and a comparison was made on the reusability and easiness in handling and maintenance.Also,a comparison of the formwork used in the construction of the 5th and 11th-floor tower based on the specific plan and drawing was done.The results showed that the aluminum formwork was found to be efficient and suitable among all formworks,although the cost was higher compared to other formwork materials.

大跨度混凝土钢筋框架梁挠度超限研究

根据大量的工程实践,大跨度钢筋混凝土框架梁由于设计不合理引起大跨度梁超限的工程案例很少,大多数是施工原因导致挠度超限。以某工程挠度超限的大跨度钢筋混凝土梁为例,根据设计资料和现场检测资料,从设计和施工两方面,利用数值计算和有限元模拟,验证分析大跨度钢筋混凝土框架梁挠度超限的原因。验证分析表明,梁板混凝土实际浇筑厚度超限与梁模板起拱高度不足可能引起梁挠度增加。当梁下立杆稳定承载力不足时,梁也易随立杆屈曲变形产生较大挠度。

拼接成型UHPC免拆模板钢筋混凝土柱的抗震性能

为研究超高性能混凝土(UHPC)免拆模板钢筋混凝土(URC)柱的抗震性能,选取UHPC免拆模板拼接方式和表面处理方式为试验设计参数,制作并完成了9个URC柱和1个钢筋混凝土(RC)柱的拟静力加载试验。模板拼接方式为螺栓加角钢连接、螺栓连接和环氧树脂砂浆连接;表面处理方式为光面处理、气泡膜印花处理和设肋处理,通过拟静力试验研究了模板拼接方式及表面处理方式对该类柱抗震性能的影响。此外,基于平截面假定,提出了URC柱的正截面偏压承载力计算式。结果表明:峰值荷载前,UHPC模板与核心混凝土黏结面无明显破坏,URC柱表现出良好的整体性,尤其是采用螺栓加角钢连接的URC柱,即使加载至极限位移时,也没有发生界面黏结失效破坏;与普通RC柱相比,URC柱的承载力提高了6.4%~43.3%,延性提高了11.4%~48.7%,耗能能力提高了27.7%~85.3%;三种连接方式中,采用螺栓加角钢连接的URC柱承载力最高,连接最可靠。最后,基于平截面假定提出的公式计算值与试验值吻合较好,可为工程应用提供参考。

3D打印混凝土永久模板叠合柱的抗压性能数值模拟研究

为深入研究3D打印混凝土永久模板叠合柱的抗压性能,基于3D打印混凝土永久模板叠合柱及同尺寸整体现浇对照柱试验建立构件数值模型,模拟分析其轴压荷载-位移响应及失效形态。针对界面粘结性能、现浇混凝土抗压强度、打印模板厚度、荷载偏心距等参数开展3D打印混凝土永久模板叠合柱的抗压性能计算分析,研究表明:叠合柱轴压极限承载力随着薄弱界面剪切强度、刚度及现浇混凝土抗压强度的增大而增大。由于打印材料的抗压强度高于现浇混凝土,叠合柱抗压极限承载力提升率与打印模板厚度呈近似线性关系,叠合圆柱的抗压极限承载力随着荷载偏心距的增大而降低,呈近似线性负相关。此外,偏心距对叠合圆柱极限承载力下降幅度的影响大于现浇圆柱。

织物增强混凝土永久模板叠合试件抗氯离子渗透性能研究

织物增强混凝土(TRC)由高性能细骨料混凝土基体与纤维网组成,TRC永久模板与核心混凝土组成叠合试件。为揭示叠合试件氯离子渗透作用规律,确定永久模板最佳厚度范围,以TRC永久厚度、耐碱纤维网层数以及界面处理方式为变量,进行叠合试件抗氯离子渗透性能试验研究和计算分析。结果表明:与未设置永久模板相比,当TRC永久模板厚度为10~50 mm时,叠合试件氯离子扩散系数分别降低73.2%~95.6%。耐碱纤维编网对永久模板抗氯离子渗透性能没有增强作用。水泥净浆涂刷、表面凿毛、短切纤维插入三种界面处理方式对叠合试件氯离子渗透系数和渗透深度的影响不显著。结合Duracrete模型定量分析,给出了海洋环境不同工况下TRC永久模板厚度建议范围。

基于铝模板BIM自动配模需求的结构模型研究

针对现有铝模板自动配模效率低和准确性差的问题,主要由BIM结构模型信息量大、建模规范性差及配模规则约束不清晰等因素造成。本文以铝模板配模设计阶段中的结构模型为研究重点,首先分析了模型中有效的空间信息与构件信息,然后在模型建模、分类编码以及避让策略方面制定了相应规则。通过选取工程案例并开发测试插件以实现信息提取与自动配模,验证了模型信息的有效性和规则的可行性。研究结果表明,所提方法不仅能显著提高铝模板BIM自动配模的效率,还能为其他BIM结构模型的相关研究提供借鉴和支持。

基于拉丁超立方抽样的高大模板支撑体系承载力有限元分析

目的研究不同缺陷构配件下高大模板支撑体系承载性能的变化,为高大模板支撑体系的布置、构配件的搭配及使用提供指导,以预防和减少其在实际工程中的坍塌事故。方法基于拉丁超立方抽样,考虑构配件缺陷对三种搭设参数模板支撑体系承载性能的影响,随机取线性屈曲分析中一阶屈曲承载力的0.1%~0.2%作为假想水平力,对构配件性能缺陷进行有限元分析,探究不同搭设参数下支撑体系承载力及失稳模式。结果SPR对承载力的影响大于D和t,并且双因素耦合对承载力的影响大于单因素。立杆步距的变化对支撑体系承载力的影响大于立杆间距。随着影响因素耦合数量的增加,步距对支撑体系承载性能的影响也会随之增大。结论支撑体系搭设过程中将存在缺陷的构配件使用时分散排布,可以防止高大模板支撑体系整体失稳倒塌。

岩棉复合保温外模板承载力及温度效应分析

为了提高建筑外围护结构施工效率及解决传统外保温系统长期存在的易脱落和易着火问题,提出了一种集保温和建筑模板于一体的岩棉复合保温外模板(RW-CIEF)体系。RW-CIEF由内到外依次为内侧加强层、岩棉保温芯材、黏结层、保温过渡层以及外侧加强层。以哈尔滨市为例,基于全寿命周期成本(life cycle cost,C lc)确定了岩棉保温芯材的最佳厚度。采用有限元分析与理论计算相结合的方法探求了RW-CIEF在工程中的可行性,分析了RW-CIEF的抗弯性能、施工承载力及温度效应下的应力和变形,讨论了开槽形式、开槽宽度、开槽深度以及开槽间距对RW-CIEF抗弯性能的影响。结果表明:RW-CIEF的抗弯性能理论计算结果与有限元分析结果有较高的一致性;开槽处理可有效提高RW-CIEF的抗弯性能,综合抗弯性能、热工特性及加工角度,建议开槽形式选用对应开井字槽或对应开纵槽,开槽深度和宽度均为10 mm,开槽间距为150 mm;设计的RW-CIEF满足施工承载力,可保证外围护结构保温工程施工质量;由温度效应产生的最大拉应力和压应力均未超过RW-CIEF的外侧加强层承载力,反映出RW-CIEF出现夏季空鼓或冬季开裂现象的可能性极小。提出的RW-CIEF体系可为外围护结构保温工程及建筑模板工程未来研究方向提供一种新的思路和方法。

一种新型预制装配式免拆模板设计与开发

为克服传统建筑模板施工质量不高、工序多、周转率低和现场环境乱等质量缺陷,在总结现有免拆模板的基础上设计、开发了一种可实现装饰装修一体化的新型预制装配式免拆模板。本文介绍了新型装配式免拆模板的基本构造及施工要点,为新型装配式免拆模板的推广应用提供一定的借鉴和参考。

镁合金建筑模板的表面化学镀与耐蚀性能

采用化学镀的方法在镁合金建筑模板表面分别制备了单一Sn膜、单一Zn膜和复合Sn-Zn膜,对比分析了pH、温度和膜层数对镁合金表面膜层显微形貌和电化学性能的影响。结果表明:对于单一膜,在pH值为6.0、温度为75℃时制备的单一Sn膜和在pH值为9.5、温度为75℃时制备的单一Zn膜都具有较好成膜质量;当膜层数为9时,复合Sn-Zn膜完全覆盖镁合金基体且膜层成膜质量较好。相较于镁合金基体,单一Sn膜、单一Zn膜、复合Sn-Zn膜的腐蚀电位都发生正向移动,腐蚀电流密度发生不同程度减小,复合Sn-Zn膜的腐蚀电位最正、腐蚀电流密度最小。在镁合金基体表面化学镀单一Sn膜、单一Zn膜、复合Sn-Zn膜都有助于提升镁合金的耐蚀性能,且复合Sn-Zn膜对基体的保护作用要优于单一Sn膜、单一Zn膜。

基于EMI-CNN的建筑施工模板支撑体系节点健康监测

为预防模板坍塌引发建筑施工安全事故风险,提出一种基于压电阻抗法(EMI)和卷积神经网络(CNN)的模板支撑体系节点智能监测方法。首先,利用压电陶瓷传感器(PZT)的机电耦合特性及其集驱动-传感于一体的特点,建立PZT-节点耦合系统的机电阻抗传感机制模型;其次,基于EMI法,以与待测结构耦合的PZT片电导信号为监测指标,确定模板支撑体系节点松动的发生;然后,以敏感频段内PZT片的801个原始电导信号为模型输入,9个节点松动程度为模型输出,构建162组学习样本和27组测试样本,建立EMI-CNN模型,确定节点松动程度;最后,以一个实际工程中的建筑施工模板体系节点为例,验证EMI-CNN模型的有效性,并对比分析EMI-BP模型。研究结果表明:EMI-CNN模型经过85次迭代达到收敛,预测准确率达到100%,相较于EMI-BP模型提高29.63%。该监测方法可实现对建筑施工模板支撑体系节点健康状态实时、准确、无损监测。

环境因素影响下钢筋混凝土索塔爬模施工仿真分析方法

为探究爬模施工进程中索塔空间温度场和应力场分布,掌握塔柱线形特性,提出一种索塔爬模施工仿真分析方法.利用Fortran编程语言开发相应子程序,对结构施加复杂温度边界,实现不同节段混凝土水化放热、收缩徐变.利用Abaqus软件对索塔爬模施工过程进行分析.结果表明:施工过程中索塔空间温度分布不均匀,塔柱表里最大温差达25.9℃,向阳面与背阴面温差最大为9℃;考虑温度效应后,塔柱所受拉应力更大,且空间应力分布具有很强的时变性,索塔线形特征与变化规律也发生改变;施工塔顶累积竖向位移先增大后减小,在爬模第16节段达到最大值20.5 mm;施工过程塔顶累计顺桥向和横桥向位移更大,最大值分别为6.5和22.3 mm.

厚煤层柔模混凝土墙沿空巷道支护技术研究

柔模混凝土墙沿空留巷技术作为无煤柱开采的一种,现已被应用于我国神东矿区多个煤矿。为解决在留巷复用过程中沿空巷道围岩结构稳定性差、变形剧烈、支护难度大的难题,以大柳塔煤矿52605柔模混凝土墙沿空留巷工作面为工程背景,采用理论分析、数值模拟和现场实测相结合的研究方法,研究了柔模混凝土墙沿空巷道的围岩变形特征,建立柔模混凝土墙沿空巷道围岩结构力学模型,得到从巷道掘进阶段至巷道复用阶段沿空巷道全生命使用周期的应力演化规律,并根据巷道不同的使用阶段提出了对应的支护方案。研究结果表明:上覆岩层作用力直接作用在直接顶与混凝土墙岩层接触位置,有利于侧向支承压力传递,巷道围岩变形较大;二次采动超前支承压力导致留巷段前方顶板发生塑性破坏,塑性破坏与底板塑性区联通,将加剧煤壁侧的破坏;现场工程实践表明对沿空巷道进行合理分时分区支护,可改善应力环境,有效控制围岩变形。

扣件钢管单面支撑体系设计与施工

随着我国城市建设土地减少,新建筑大多数都紧贴用地红线而建,而且很多新建筑地下室外墙厚度越来越厚,常规双面支模无法施工,因此越来越多的地下室外墙采用内侧单面支模的方法施工。虽然扣件钢管排架斜撑在单面支模施工中有一定的应用,但相关设计计算与施工经验不足。细致剖析单侧支模支撑形式多种类型及其特点,针对某具体工程的地下室外墙单侧支模工程,创新性地引入了一种优化后的扣件排架斜撑搭设策略。通过对该单侧支撑体系的研究,构建了精细的有限元模型,并进行了深入的应力、变形及稳定性评估,可为类似单侧支模支撑体系的设计与施工提供参考。

预制模壳填芯混凝土悬臂盖梁承载力分析

盖梁的轻量化发展是实现全预制桥梁的必然要求。基于已有的预制模壳填芯混凝土悬臂盖梁静力试验,采用有限元软件ABAQUS对试件PRC1进行数值分析,有限元计算结果和试验结果吻合较好,验证了有限元模型的可靠性。通过修改已验证的有限元模型参数,进一步分析外壳混凝土强度、纵筋配筋率和交界面接触设置对预制模壳填芯混凝土悬臂盖梁力学性能的影响。基于钢筋混凝土一般构件的承载力计算方法建立试件的理论计算公式,并对提出的计算公式进行验证。研究结果表明:当外壳材料为普通混凝土时,混凝土强度等级从C35增加到C60,峰值承载力仅提高1%,而当外壳材料为超高性能混凝土(UHPC)时,峰值承载力相较C35提高了22%。纵筋配筋率与峰值承载力呈线性增长趋势,当顶部第1排纵筋直径从14 mm增加到22 mm时,峰值承载力提高了34%。交界面接触设置为绑定约束比面面接触的峰值承载力更接近试验值,且后者是相对保守的。基于钢筋混凝土一般构件建立的承载力计算方法所计算结果与试验结果和有限元分析结果吻合较好。