Geomorphic Evidence for and Rate of Sinistral Strike-slip Movement Along Northwest-trending Faults in Chaoshan Plain

Two sets of active faults,northwest-and northeast-trending faults,are developed in the Chao-shan Plain of East Guangdong.After detailed interpretation of aerophotos,we have found outthat there is the clear phenomenon of sinistral dislocation of drainage system on the Huang-gang-shui fault and part of Fengshun-Shantou fault.Field investigation confirmed that the geo-morphic bodies along the two faults have undergone displacement.Large-scale topographicmapping was made at three displaced sites and samples for age dating were collected from thegeomorphic booies.Calculation indicates that the average rate of sinistral strike-slip movementin the Holocene time amounts to 1.11±0.09～2.69±0.24mm/a along the Huanggangshuifault and 3.26±0.26mm/a along the Fengshun-Shantou fault.These two more active NW-trending faults extend into sea area,where they intersect the NE-trending strongly active Nius-han Island-Xiongdi Isle-Nanpeng Isles fault at a depth of 40～50m in water.The intersection isa location favorable

Sinistral strike slip of the Zhangjiakou-Penglai Fault and its control on hydrocarbon accumulation in the northeast of Shaleitian Bulge,Bohai Bay Basin,East China

The structural style, fault activity, strike-slip displacement, and the formation mechanism and hydrocarbon migration and accumulation in the center tectonic zone in the northeast Shaleitian Bulge of Zhangjiakou-Penglai Fault Zone were studied by seismic attribute analysis, structural geometric analysis, fault activity analysis, structure evolution history and simulation of hydrocarbon migration, based on 3-D seismic and drilling data. The main results are as follows:(1) The study area is a superimposed tectonic zone, which experienced early(Paleocene and Eocene) extension and late(Oligocene and Pliocene-Quaternary) strike-slip and pull-apart.(2) The sinistral strike slip of the northeast Shaleitian Bulge of Zhangjiakou-Penglai Fault Zone went through two periods, Oligocene and Pliocene-Quaternary, and the Bohai section was active earlier than the inland section.(3) The sinistral strike slip displacement of Zhangjiakou-Penglai Fault is 4 km since Cenozoic, including 1 km in the Oligocene, and 3 km in the Pliocene-Quaternary.(4) The strike-slip movements have resulted in the increase of fault activity and basin-mountain restructure in the fault zone, also contributed to the formation of the central tectonic belt and the conjugate evolution in north-east structural belt.(5) The conjugate strike slip of the Zhangjiakou-Penglai Fault Zone dominated the migration and accumulation of hydrocarbon in shallow formations by controlling the injection points and segments of hydrocarbon from the deep layers to shallow layers.

Sinistral Strike-slip Movement Along Western Terminal Segment of the Active Daqingshan Piedmont Fault, Inner Mongolia, China

There are 18 gullies displaying sinistral contortions to different degrees along the western terminal segment about 10 km long of the active Daqingshan piedmont fault near the Donghe District, Baotou City. The contortion amount of gullies ranges from 20 m to 300 m. The contortion and length of the gullies are in direct proportion. The relation between piedmont terraces and gullies indicates that the gullies with upper reaches of about 1 ～ 5 km long and those smaller than one kilometer were formed at the end of Late Pleistocene and Holocene.Meanwhile, sandy gravel layer of alluvial-proluvial sediment on the upthrown wall is directly in contact with yellow clayey sand of the downthrown wall. During the Holocene, the sinistral strike-slip rate along the western terminal segment of the active Daqingshan piedmont fault reached 5 mm/a from age data of dislocated sediments. The evolutional mechanism of the active Daqingshan piedmont fault is also discussed in the paper.

TWO PHASES OF CENOZOIC DEFORMATION IN NORTHEASTERN TIBET: THRUSTING FOLLOWED BY STRIKE-SLIP FAULTING

In order to establish deformation history for the Cenozoic development of the Tibetan Plateau, we conducted geologic mapping along a 120km traverse between Nangqian and Yushu in the northeastern Qiangtang terrane. This work reveals a complex interaction among Tertiary thrusting, strike\|slip faulting, sedimentation, and igneous activity. Two phases of deformation are recognized. The older northeast—southwest shortening, expressed by thrusting and folding, is followed by left\|slip faulting along northwest\|trending faults. Tertiary thrusts, predominantly southwest\|dipping, are distributed throughout the traverse, and typically juxtapose Mesozoic strata over Paleogene strata. The latter were deposited in several separated basins during folding and thrusting, as indicated by well\|developed growth strata. A preliminary construction of balanced cross\|sections suggests a minimum estimate of 45km of crustal shortening along the traverse. Numerous hypabyssal intrusions were mapped in the southern part of the traverse near Nangqian. They were emplaced into the Paleogene sediments and are dated between 36 and 33Ma by 40 Ar/ 39 Ar and U\|Pb methods. Paleogene sediments are also interbedded with volcanics in both the southern and northern parts of the study area. In the northernmost part of the traverse, a volcanic unit overlies a Tertiary thrust. This unit itself is broadly folded. This relationship suggests that Tertiary igneous activity was coeval with contractional deformation in the region, implying strongly the causal relationship between the two processes. The youngest event in the area is the development of northwest\|trending left\|slip faults. They cut Tertiary thrusts, folds, and about 35Ma igneous intrusions. In contrast to widely distributed Tertiary folds and thrusts, strike\|slip faulting is restricted only to the southern portion of our mapped area near Nangqian. The strike\|slip faults apparently control the distribution of modern drainage systems, suggesting that they may have been active recently. As the younger strike\|slip faults are subparallel to the older folds and thrusts, we have not been able to determine the magnitude of left\|slip on these faults. We interpret the termination of contractional deformation and the subsequent replacement by strike\|slip faulting as a result of both clockwise rotation of the region and westward propagation of strike\|slip deformation in eastern Tibet.

The Dihedral Angle and Intersection Processes of a Conjugate Strike-Slip Fault System in the Tarim Basin, NW China

Recent studies, focused on dihedral angles and intersection processes, have increased understandings of conjugate fault mechanisms. We present new 3-D seismic data and microstructural core analysis in a case study of a large conjugate strike-slip fault system from the intracratonic Tarim Basin, NW China. Within our study area, ＂X＂ type NE and NW trending faults occur within Cambrian- Ordovician carbonates. The dihedral angles of these conjugate faults have narrow ranges, 19~ to 62~ in the Cambrian and 26~ to 51~ in the Ordovician, and their modes are 42~ and 44~ respectively. These data are significantly different from the ~60~ predicted by the Coulomb fracture criterion. It is concluded that： （1） The dihedral angles of the conjugate faults were not controlled by confining pressure, which was low and associated with shallow burial; （2） As dihedral angles were not controlled by pressure they can be used to determine the shortening direction during faulting; （3） Sequential slip may have played an important role in forming conjugate fault intersections; （4） The conjugate fault system of the Tarim basin initiated as rhombic joints; these subsequently developed into sequentially active ＂X＂ type conjugate faults; followed by preferential development of the NW-trending faults; then reactivation of the NE trending faults. This intact rhombic conjugate fault system presents new insights into mechanisms of dihedral angle development, with particular relevance to intracratonic basins.

Uniform Strike-Slip Rate along the Xianshuihe-Xiaojiang Fault System and Its Implications for Active Tectonics in Southeastern Tibet

Recent studies on the Xianshuihe-Xiaojiang fault system suggest that the Late Quaternary strike-slip rate is approximately uniform along the entire length of the fault zone, about 15±2 mm/a. This approximately uniform strike slip rate strongly supports the clockwise rotation model of the southeastern Tibetan crust. By approximating the geometry of the arc-shaped Xianshuihe-Xiaojiang fault system as a portion of a small circle on a spherical Earth, the 15±2 mm/a strike slip rate corresponds to clockwise rotation of the Southeastern Tibetan Block at the （5.2±0.7）×10^-7 deg/a angular velocity around the pole （21°N, 88°E） relative to the Northeast Tibetan Block. The approximately uniform strike slip rate along the Xianshuihe-Xiaojiang fault system also implies that the Longmeushan thrust zone is not active, or at least its activity has been very weak since the Late Quaternary. Moreover, the total offset along the Xiaushuihe-Xiaojiang fault system suggests that the lateral extrusion of the Southeastern Tibetan Block relative to Northeastern Tibetan Block is about 160 km and 200-240 km relative to the Tarim-North China block. This amount of lateral extrusion of the Tibetan crust should have accommodated about 13-24% convergence between India and Eurasia based on mass balance calculations. Assuming that the slip rate of 15±2 mm/a is constant throughout the entire history of the Xianshuihe-Xiaojiang fault system, 11±1.5 Ma is needed for the Xianshuihe-Xiaojiang fault system to attain the 160 km of total offset. This implies that left-slip faulting on the Xianshuihe-Xiaojiang fault system might start at 11±1.5 Ma.

A Large-Scale Palaeozoic Dextral Ductile Strike-Slip Zone:the Aqqikkudug-Weiya Zone along the Northern Margin of the Central Tianshan Belt,Xinjiang,NW China

Abstract The nearly E-W-trending Aqqikkudug-Weiya zone, more than 1000 km long and about 30 km wide, is an important segment in the Central Asian tectonic framework. It is distributed along the northern margin of the Central Tianshan belt in Xinjiang, NW China and is composed of mylonitized Early Palaeozoic greywacke, volcanic rocks, ophiolitic blocks as a mélange complex, HP/LT-type bleuschist blocks and mylonitized Neoproterozoic schist, gneiss and orthogneiss. Nearly vertical mylonitic foliation and sub-horizontal stretching lineation define its strike-slip feature; various kinematic indicators, such as asymmetric folds, non-coaxial asymmetric macro- to micro-structures and C-axis fabrics of quartz grains of mylonites, suggest that it is a dextral strike-slip ductile shear zone oriented in a nearly E-W direction characterized by “flower” strusture with thrusting or extruding across the zone toward the two sides and upright folds with gently plunging hinges. The Aqqikkudug-Weiya zone experienced at least two stages of ductile shear tectonic evolution: Early Palaeozoic north vergent thrusting ductile shear and Late Carboniferous-Early Permian strike-slip deformation. The strike-slip ductile shear likely took place during Late Palaeozoic time, dated at 269±5 Ma by the40Ar/39Ar analysis on neo-muscovites. The strike-slip deformation was followed by the Hercynian violent S-type granitic magmatism. Geodynamical analysis suggests that the large-scale dextral strike-slip ductile shearing is likely the result of intracontinental adjustment deformation after the collision of the Siberian continental plate towards the northern margin of the Tarim continental plate during the Late Carboniferous. The Himalayan tectonism locally deformed the zone, marked by final uplift, brittle layer-slip and step-type thrust faults, transcurrent faults and E-W-elongated Mesozoic-Cenozoic basins.

The characteristics of tectonic stress field about strike slip earthquake－generating structure in the Chinese mainland

This paper is one of the series papers about the study on strike-slip earthquake-generating structure in the Chinese mainland. In the first part of this paper, based on the large amount of data from large earthquake investigation and the latest results of focal mechanism, the earthquake-generating structure in the Chinese mainland interior and its neighbouring region is discussed. It is concluded that the absolutely predominated earthquake, not only in number, but also in intensity, as well as in distributing area, is strike slip earthquake, and it is further stressed that the study on the strike slip earthquake-generating structure is significant for seismic risk analysis. In the second part, the characteristics of tectonic stress field about strike slip earthquake-generating structure and the compiled distribution outline of strike slip earthquake-generating fault, normal fault, and thrust fault in the Chinese mainland interior and its neighbouring region, in the light of stress characteristics of fault plane solutions, are also discussed.

Characteristics of strike-slip inversion structures of the Karatau fault and their petroleum geological significances in the South Turgay Basin,Kazakhstan

The Karatau fault is one of the important strike-slip faults in central Asia,and the South Turgay Basin is located towards its northern end.Detailed seismic interpretation indicated that the strikeslip tectonism of the Karatau fault weakened gradually from west to east in the South Turgay Basin.Typical flower structures developed on the section,and strike-slip faults showed an echelon pattern on planar view.The Karatau strike-slip fault affected the South Turgay Basin in two periods：（1） The South Turgay strike-slip pull-apart rift basin formed as a result of regional extensive stress in the Early-Middle Jurassic,characterized by the juxtaposition of horsts and grabens.The formation of horsts provided favorable reservoir spaces for later hydrocarbon accumulation,and different filling stages of grabens controlled different reservoir-forming factors in grabens.（2） Two stages of tectonic inversion occurred in the Late Jurassic and Late Cretaceous and played a crucial role in the final shape of the structure in the South Turgay Basin.The oil and gas migrated to form reservoirs and mainly concentrated in the horsts,graben slopes and in both sides of the strike-slip fault zone.In the case of the degree of accumulation of petroleum,the factor explaining why horsts are better than grabens is the strike-slip pull-apart of the South Turgay Basin,and the structure inversion of the South Turgay Basin explains why the west graben is better than the east one.Overall,the Karatau strike-slip fault played a very important role in the formation of the South Turgay Basin and its hydrocarbon accumulations.

Characteristics and evolution of strike-slip tectonics of the Liaohe Western Sag,Bohai Bay Basin

Because of its rich oil and gas resources and the special tectonic location of the Liaohe Western Sag （the Tanlu Fault traverses the sag）, Bohai Bay Basin, a detailed study of its strike-slip tectonics is significant in revealing the sag＇s tectonic evolution, its control on hydrocarbon accumulation, and the activity history of the northern section of the Tanlu Fault in the Cenozoic. Through systematic structure analysis of 3D seismic data of the Liaohe Western Sag, combined with balanced section analysis, a variety of structural features in relation to right-lateral strike-slip faults, such as echelon normal faults, ＂comb＂ structure, ＂flower＂ structure,＂interpretable＂ and ＂buried＂ strike-slip faults have been revealed exist in the Liaohe Western Sag. According to the research in this paper, the complex structural phenomena in the Liaohe Western Sag could be reasonably interpreted as right-lateral strike-slip activity and the strike-slip activities of the Liaohe Western Sag began in the early Oligocene. The activity was weak at the beginning （E3s1-2）, then strengthened gradually and reached its strongest level in the late Oligocene （E3d1）. In the Miocene, the strike-slip activity was low and then strengthened significantly once again from the Pliocene to the present. It is speculated that the entire northern section of the Tanlu Fault has had a similar evolution history since the Oligocene.

Characteristics of the Late Quaternary right-lateral strike-slip movement of Bolokenu-Aqikekuduk fault in northern Tianshan Mountains,NW China

The characteristics of the Bolokenu-Aqikekuduk（Bo-A） fault,a right-lateral strike-slip fault that runs for more than 700 km long and obliquely cuts North Tianshan Mountains,are evaluated here based on remote sensing data,and through an analysis of the results from field investigations as well as climate-geomorphic events. The fault is composed of a western segment with a NW strike and an eastern segment with a NWW strike.The western segment is nearly 250 km long,extending northwestward into Kazakhstan with a right-lateral strike-slip rate of 5 mm/a.This domain consists of 4-5 rupture sections,with 3-4 deformation belts,caused by ancient or historical earthquakes,and suggesting the potential for the occurrence of further strong earthquakes（with M≈7.5） in future. The eastern segment of the fault shows a right-lateral strike-slip rate of 1-1.4 mm/a,with the development of 3-4 deformation belts caused by ancient or historical earthquakes,and with a potential for future strong earthquake with M≈7.0. A typical strain partitioning style in the compression area has developed between the intermontane BoA fault and the piedmont thrust structures of Northern Tianshan Mountains,under the effect of oblique compression,as indicated by the piedmont thrust structure and the strike-slip fault in the mountains.

Neotectonics of the Eastern Margin of the Tibetan Plateau: New Geological Evidence for the Change from Early Pleistocene Transpression to Late Pleistocene-Holocene Strike-slip Faulting

We present in this paper some new evidence for the change during the Quaternary in kinematics of faults cutting the eastern margin of the Tibetan Plateau. It shows that significant shortening deformation occurred during the Early Pleistocene, evidenced by eastward thrusting of Mesozoic carbonates on the Pliocene lacustrine deposits along the Minjiang upstream fault zone and by development of the transpressional ridges of basement rocks along the Anninghe river valley. The Middle Pleistocene seems to be a relaxant stage with local development of the intra-mountain basins particularly prominent along the Minjiang Upstream and along the southern segment of the Anninghe River Valley. This relaxation may have been duo to a local collapse of the thickened crust attained during the late Neogene to early Pleistocene across this marginal zone. Fault kinematics has been changed since the late Pleistocene, and was predominated by reverse sinistral strike-slip along the Minshan Uplift, reverse dextral strike-slip on the Longmenshan fault zone and pure sinistral strike-slip on the Anninghe fault. This change in fault kinematics during the Quaternary allows a better understanding of the mechanism by which the marginal ranges of the plateau has been built through episodic activities.

On the faults of western Hexi Corridor and its nearby regions, northwestern China: Thrust faults and strike-slip faults of Late Cenozoic

The structural analysis based on the explanation of seismic profiles indicates that a lot of thrust faults and strike-slip faults of Late Cenozoic occur in western Hexi Corridor and its nearby regions. They can be divided into two types. One is thrust faults dipping southwards and extending NWwards, which was mainly correlated with the thrusting of northern Qilianshan and located at the NE margin of Qilianshan and the southwestern Hexi Corridor, the other is thrust faults and strike-slip faults that were related to the strike-slipping of Altun fault and located mainly at the regions of Hongliuxia, Kuantaishan, and Helishan that are close to the Altun fault. All these faults, which were related to the remote effects of collision between the two continents of India and Tibet during the Late Eocene and later, started to develop since the Late Tertiary and presented the features of violent thrust or strike-slip movement in Quaternary. Many of them are still active up to now and thus belong to the active faults that are the potential inducement of earthquakes in the Hexi Corridor. Moreover, a lot of intense structural deformation and many morphology phenomena such as tectonic terrace and river offset were formed under the control of these faults in Quaternary.

Strain analysis of buried steel pipelines across strike-slip faults

Existing analytical methods of buried steel pipelines subjected to active strike-slip faults depended on a number of simplifications.To study the failure mechanism more accurately,a refined strain analytical methodology was proposed,taking the nonlinear characteristics of soil-pipeline interaction and pipe steel into account.Based on the elastic-beam and beam-on-elastic-foundation theories,the position of pipe potential destruction and the strain and deformation distributions along the pipeline were derived.Compared with existing analytical methods and three-dimensional nonlinear finite element analysis,the maximum axial total strains of pipe from the analytical methodology presented are in good agreement with the finite element results at small and intermediate fault movements and become gradually more conservative at large fault displacements.The position of pipe potential failure and the deformation distribution along the pipeline are fairly consistent with the finite element results.

TECTONIC-GEOMORPHIC FEATURES OF THE STRIKE-SLIP FAULT ZONE IN EASTERN HUNAN AND WESTERN JIANGXI

Eastern Hunan-western Jiangxi, the main distribution domain of the Luoxiao MountainRange, is one of the key districts of the Circum-Pacific tectonically active belt in China, in whichNNE-trending en echelon strike-slip faulting since Cenozoic time has obviously controlled thefundamental framework of the modern land forms. Based on the study of tectonic evolution and ac-tive strike-slip faults, this paper discusses the forms, types and combinations of the modern tec-tonic land forms in this region.

CENOZOIC LARGE-SCALE STRIKE-SLIP FAULT IN WEST YUNNAN, CHINA

During the collision between India and Eurasia, the continental compression and shorten is thought to be absorbed by the way of thickening of the Tibetan plateau crust and strike\|slip extrusion outwardly of blocks surrounding the Tibetan plateau. A series of models have been proposed recently, of which the most typical one is continental blocks extrusion by Tapponnier et al.. Virtually previous studies show that the Red River—Ailaoshan fault is the eastern boundary of extrusion Indochina displaced southward relative to South China about 23 Ma ago, and more, the western boundary of extrusion blocks is inferred to be Sijie fault in the eastern Burma. But the movement age of Sijie fault is around 13 Ma inferred from the age of Andeman Sea formation and different from that of the Red River—Ailaoshan fault. It is an important scientific problem where the western boundary of extrusion blocks is.

INVERSION OF STRIKE-SLIP MOVEMENTS ALONG THE YARLUNG ZANGBO SUTURE ZONE, TIBET

Meso\| and microstructural characteristics of cataclastic fault rocks developed in the Xialu chert are described. The Xialu chert represents pelagic and deep marine sediments (Middle Jurassic—Lower Cretaceous), and occupies the southern marginal part of the E—W trending Yarlung Zangbo suture zone. The apparent total thickness of siliceous deposits exceeds 1km. The current study is concentrated along the two measured sections, Xialu\|E and Xialu\|W. The Xialu\|E section is composed mainly of red chert associated with reddish purple siliceous mudstone and greenish gray mudstone. The beds steeply dip north or south. The 45m section studied is divided into three units (chert unit, chert\|siliceous mudstone unit, and melange unit from north to south). They are in fault contact with each other. In the southern half of the chert unit and the northernmost of the chert\|siliceous mudstone unit, a 15m thick cohesive cataclasite zone can be defined. The cataclasites are composed of chert fragments in a fine grained matrix, and deformed with jigsaw puzzle structures. The chert\|siliceous mudstone unit is made up of four slabs of chert\|siliceous mudstone sequence. Mesoscopic duplex zones in thickness from 1 to 3m are recognized at slab boundaries. Flat and ramp structure and associated P foliations, R1 shears, Y surfaces are developed. Shear spacing range from 1 to 10cm. The slip senses are dextral strike\|slip movement along these duplex zones. The cataclasite zone is cut by the duplex zone along the southern boundary.

Decadal Seismicity before Great Earthquakes—Strike-Slip Faults and Plate Interiors: Major Asperities and Low-Coupling Zones

Decadal forerunning seismic activity is examined for very large, shallow earthquakes along strike-slip and intraplate faults of the world. It includes forerunning shocks of magnitude Mw ≥ 5.0 for 21 mainshocks of Mw 7.5 to 8.6 from 1989 to 2020. Much forerunning activity occurred at what are interpreted to be smaller asperities along the peripheries of the rupture zones of great mainshocks at transform faults and subduction zones. Several great asperities as ascertained from forerunning activity agree with the areas of high seismic slip as determined by others using geodetic, mapping of surface faulting, and finite-source seismic modeling. The zones of high slip in many great earthquakes were nearly quiescent beforehand and are identified as the sites of great asperities. Asperities are strong, well-coupled portions of plate interfaces. Different patterns of forerunning activity on time scales of up to 45 years are attributed to the sizes and spacing of asperities (or lack of). This permits at least some great asperities along transform faults to be mapped decades before they rupture in great shocks. Rupture zones of many great mainshocks along transform faults are bordered either along strike, at depth or regionally by zones of lower plate coupling including either fault creep forerunning activity, aftershocks and/or slow-slip events. Forerunning activity to transforms in continental areas is more widespread spatially than that adjacent to oceanic transforms. The parts of the San Andreas fault themselves that ruptured in great California earthquakes during 1812, 1857 and 1906 have been very quiet since 1920;moderate to large shocks have been concentrated on their peripheries. The intraplate shocks studied, however, exhibited few if any forerunning events, which is attributed to the short period of time studied compared to their repeat times. The detection of forerunning and precursory activities for various time scales should be sought on the peripheries of great asperities and not just along the major faults themselves. This paper compliments that on decadal forerunning activity to great and giant earthquakes along subduction zones.

PALEOCENE—MIDDLE EOCENE DEXTRAL STRIKE-SLIP DEFORMATION AND ITS TECTONIC IMPLICATION IN THE WESTERN YUNNAN, CHINA

The Western Yunnan located at the southeast margin of east Himalaya\|Burman syntaxis. A great number of small basins filled with lacustrine developed in the Indochina block during the Paleocene\|middle Eocene. Occurrence of basins as en chelon arrangement suggests that they were formed under tectonic setting of right\|lateral strike\|slip. The north termination of main faults controlling basins deposition and evolution, meet the Red River fault as an acute angle. The Lanping basin, one representative of all basins, is chosen to study its formation mechanism. Facts of rapid lateral phase change, sediment offset from their source and lateral migration of alluvial fan, indicate that the Lanping basin is a strike\|slip basin and its boundary main fault is syndepositional left\|lateral strike\|slip normal fault. Basin formation was controlled by mechanism of strike\|slip and pull\|apart, the Lanping basin belongs to extension strike\|slip basin. The nature of the Lanping basin and infill suggest that the boundary fault controlling basin deposit was formed during right\|lateral strike\|slip deformation of the Red River fault. Whether formation mechanism of single basin or occurrence of basins supported that the Red River fault was a right\|lateral strike\|slip fault during the Paleocene\|middle Eocene.

Recent geodynamics of major strike-slip zones

The subject of this study is strike-slip fault zones, where temporal variations of accumulation in strike-slip deformation complicate the standard process of deformation accu- mulation and release during strong earthquakes. These temporal variations are expressed in the E1 Ghab segment of the Dead Sea Transform zone （DST, Eastern Mediterranean） and in the Talas-Fergana fault zone （Central Asia）. According to Global Positioning System （GPS） data, the strike-slip deformations within these zones are not now accumulating or are accumulating at a rate that is significantly less than their average rate during the Holocene and Quaternary or the Pliocene-Quaternary. Simultaneously, weak transverse shortening has been measured in both zones by GPS. In both of these zones, strong earthquakes have not registered within the XX century, yet epochs of intensified seismicity （strong earthquakes） took place throughout history. In the southern and central parts of the E1 Ghab zone, there is evidence of 30 strong historical earthquakes of Ms ≥ 5.7; however, no instrumental earthquakes of Ms 〉 5 have been identified. The temporal distribution of seismic energy released by these earthquakes demonstrates a 350 ± 50-year cycle. Values for the seismic energies released during the peak phases of these cycles are approximated by a sinusoid that suggests the possibility of a 〉1800-year cycle （＂hyper-cycle＂）, which began around the 3rd century, reached its maximum in the 12th century, and has continued until now. A combination of geological, archaeoseismological, and geodetic data show that the rate of sinistral strike-slip deformation varied in the fault zone, probably in conformity with the variation of seismicity during the ＂hyper-cycle.＂ In the Talas-Fergana fault zone, trenching and 14C dating that was correlated with right lateral offsets, gave a possible preliminary estimate of the average rates of the Late Holocene strike slip of about 10 mm per year, with a decrease in the SE direction to 4 mm-4.5 mm per year. These studies also showed that the slip in the Talas-Fergana fault zone was realized mainly during strong earthquakes. New trenching and 14C dating of paleoearthquake records identified the epoch of seismicity intensification dating to the XIV-XVII centuries. These paleoearthquakes could produce a total dextral slip at several meters. Therefore, consid- eration of these epochs was necessary to determine a calculated average slip rate during the Late Holocene.