The effect of grain size of primary α phase on the bonding interface characteristic and shear strength of bond was investigated in the press bonding of Ti-6Al-4V alloy. The quantitative results show that the average ...The effect of grain size of primary α phase on the bonding interface characteristic and shear strength of bond was investigated in the press bonding of Ti-6Al-4V alloy. The quantitative results show that the average size of voids increases from 0.8 to 2.6 μm and the bonding ratio decreases from 90.9% to 77.8% with an increase in grain size of primary α phase from 8.2 to 16.4 μm. The shape of voids changes from the tiny round to the irregular strip. The highest shear strength of bond can be obtained in the Ti-6Al-4V alloy with a grain size of 8.2 μm. This is contributed to the higher ability of plastic flow and more short-paths for diffusion in the alloy with smaller grain size of primary α phase, which promote the void closure process and the formation of α/β grains across bonding interface.展开更多
β-Si3N4 powders prepared by self-propagating high-temperature synthesis （SHS） with additions of Y2O3 and Al2O3 were sintered by spark plasma sintering （SPS）. The densification, microstructure, and mechanical prop...β-Si3N4 powders prepared by self-propagating high-temperature synthesis （SHS） with additions of Y2O3 and Al2O3 were sintered by spark plasma sintering （SPS）. The densification, microstructure, and mechanical properties of Si3N4 ceramics prepared using this method were compared with those obtained by hot pressing process. Well densified Si3N4 ceramics with finer and homogeneous microstructure and better mechanical properties were obtained in the case of the SPS technique at 200°C lower than that of hot pressing. The microhardness is 15.72 GPa, the bending strength is 716.46 MPa, and the fracture toughness is 7.03 MPa·m1/2.展开更多
Characteristics of magnetic hardening in cast-hot pressed magnet Pr_(19)Fe_(74.5)B_5Cu_(1.5)were stu- died.The microstructure features and virgin magnetization curve reveal a nucleation control- led coercivity mechani...Characteristics of magnetic hardening in cast-hot pressed magnet Pr_(19)Fe_(74.5)B_5Cu_(1.5)were stu- died.The microstructure features and virgin magnetization curve reveal a nucleation control- led coercivity mechanism.Regression analysis shows that the intrinsic coercivity varies inversely as the logarithm of the average grain size: _iH_c(MA/m)=1.7312-0.48161nd(μm) which confirms the randomness of nucleation of reversed domains and the statistical nature of coercivity,indicating that the decrease of grain size would reduce the average number of de- fects on its surface and lower the probability of magnetization reversal of a grain and the cu- mulative fraction of the grains that have reversed their magnetization.Coercivity is thus en- hanced.展开更多
A modem design method, in which traditional design formulas are conjoined with numerical simulation and optimization, is successfully used to design the out-size extrusion flame precisely so that the press cost can be...A modem design method, in which traditional design formulas are conjoined with numerical simulation and optimization, is successfully used to design the out-size extrusion flame precisely so that the press cost can be saved. A new technology used for decompressing by a multi-steps dynamical mode is put forward, which makes it possible to decompress the large flow-volume high-pressure oil in the main cylinders. In addition, a method for realizing the fixed mandrel process by hydraulic support is proposed and its control equation is established. Pre-tightening frame tests are carried out by over-operating pressure on 100 MN aluminium extrusion press with oil-driven double action, which is developed based on the above key techniques and is the largest press so far in the world, and the results show that the frame structure designed is reasonable and reliable, and the modem design method used is an useful tool for designing large and out-size heavy plastic forming machinery. The results of decompressing curve in main cylinder and noise inspection indicate that multi-steps dynamical mode for decompressing the large flow-volume high pressure oil is valid and reliable. Meanwhile, the fixed mandrel process is well realized based on the control equation. These key techniques have been used in the development of 125 MN aluminium extrusion press with oil-driven double action.展开更多
Studies of pressure-volume curves have shown that the filter pressing behaviours depend on pH values of the alumina dispersion. Densimetry and porosimetry of the filter cakes have revealed that higher density, smalle...Studies of pressure-volume curves have shown that the filter pressing behaviours depend on pH values of the alumina dispersion. Densimetry and porosimetry of the filter cakes have revealed that higher density, smaller mode pore size and lower specific volume of total pores can be achieved by controlling electrostabilization. (Author abstract) 9 Refs.展开更多
Microstructure evolution and texture development and their effects on mechanical properties of a Mg-Gd-Y-Zr alloy during equal channel angular pressing（ECAP） were investigated.It is found that the microstructure is ...Microstructure evolution and texture development and their effects on mechanical properties of a Mg-Gd-Y-Zr alloy during equal channel angular pressing（ECAP） were investigated.It is found that the microstructure is still inhomogeneous after four passes,and two zones,namely the fine grain zone（FGZ） and the coarse grain zone（CGZ） are formed.The grain refinement occurs mainly by particle-stimulated nucleation（PSN） mechanism,which led to a more random texture after four passes of ECAP.In the ECAP-processed alloy,the strength did not increase while the ductility was enhanced dramatically compared with the as-received condition.The change of ductility of this alloy was discussed in terms of texture and second phase particles.展开更多
基金Project(2014M562447) supported by the China Postdoctoral Science FoundationProject(51275416) supported by the National Natural Science Foundation of China+1 种基金Project(BP201503) supported by the Research Fund of the State Key Laboratory of Solidification Processing(NWPU)China
文摘The effect of grain size of primary α phase on the bonding interface characteristic and shear strength of bond was investigated in the press bonding of Ti-6Al-4V alloy. The quantitative results show that the average size of voids increases from 0.8 to 2.6 μm and the bonding ratio decreases from 90.9% to 77.8% with an increase in grain size of primary α phase from 8.2 to 16.4 μm. The shape of voids changes from the tiny round to the irregular strip. The highest shear strength of bond can be obtained in the Ti-6Al-4V alloy with a grain size of 8.2 μm. This is contributed to the higher ability of plastic flow and more short-paths for diffusion in the alloy with smaller grain size of primary α phase, which promote the void closure process and the formation of α/β grains across bonding interface.
基金the National Natural Science Foundation of China (No.2001AA333080).
文摘β-Si3N4 powders prepared by self-propagating high-temperature synthesis （SHS） with additions of Y2O3 and Al2O3 were sintered by spark plasma sintering （SPS）. The densification, microstructure, and mechanical properties of Si3N4 ceramics prepared using this method were compared with those obtained by hot pressing process. Well densified Si3N4 ceramics with finer and homogeneous microstructure and better mechanical properties were obtained in the case of the SPS technique at 200°C lower than that of hot pressing. The microhardness is 15.72 GPa, the bending strength is 716.46 MPa, and the fracture toughness is 7.03 MPa·m1/2.
文摘Characteristics of magnetic hardening in cast-hot pressed magnet Pr_(19)Fe_(74.5)B_5Cu_(1.5)were stu- died.The microstructure features and virgin magnetization curve reveal a nucleation control- led coercivity mechanism.Regression analysis shows that the intrinsic coercivity varies inversely as the logarithm of the average grain size: _iH_c(MA/m)=1.7312-0.48161nd(μm) which confirms the randomness of nucleation of reversed domains and the statistical nature of coercivity,indicating that the decrease of grain size would reduce the average number of de- fects on its surface and lower the probability of magnetization reversal of a grain and the cu- mulative fraction of the grains that have reversed their magnetization.Coercivity is thus en- hanced.
基金This project is supported by National Science Foundation of China for Distinguished Young Scholars (No. 50225518)Foundation of China for Key New Product (No. 2004ED850025)Post-Doctoral Foundation of China Heavy Machinery Research Institute (No. K055412).
文摘A modem design method, in which traditional design formulas are conjoined with numerical simulation and optimization, is successfully used to design the out-size extrusion flame precisely so that the press cost can be saved. A new technology used for decompressing by a multi-steps dynamical mode is put forward, which makes it possible to decompress the large flow-volume high-pressure oil in the main cylinders. In addition, a method for realizing the fixed mandrel process by hydraulic support is proposed and its control equation is established. Pre-tightening frame tests are carried out by over-operating pressure on 100 MN aluminium extrusion press with oil-driven double action, which is developed based on the above key techniques and is the largest press so far in the world, and the results show that the frame structure designed is reasonable and reliable, and the modem design method used is an useful tool for designing large and out-size heavy plastic forming machinery. The results of decompressing curve in main cylinder and noise inspection indicate that multi-steps dynamical mode for decompressing the large flow-volume high pressure oil is valid and reliable. Meanwhile, the fixed mandrel process is well realized based on the control equation. These key techniques have been used in the development of 125 MN aluminium extrusion press with oil-driven double action.
文摘Studies of pressure-volume curves have shown that the filter pressing behaviours depend on pH values of the alumina dispersion. Densimetry and porosimetry of the filter cakes have revealed that higher density, smaller mode pore size and lower specific volume of total pores can be achieved by controlling electrostabilization. (Author abstract) 9 Refs.
文摘Microstructure evolution and texture development and their effects on mechanical properties of a Mg-Gd-Y-Zr alloy during equal channel angular pressing（ECAP） were investigated.It is found that the microstructure is still inhomogeneous after four passes,and two zones,namely the fine grain zone（FGZ） and the coarse grain zone（CGZ） are formed.The grain refinement occurs mainly by particle-stimulated nucleation（PSN） mechanism,which led to a more random texture after four passes of ECAP.In the ECAP-processed alloy,the strength did not increase while the ductility was enhanced dramatically compared with the as-received condition.The change of ductility of this alloy was discussed in terms of texture and second phase particles.
