Revealing the role of pyramidal slip in the high ductility of Mg-Li alloy

The high ductility of Mg-Li alloy has been mainly ascribed to a high activity of pyramidal<c+a>slip to accommodate plastic strain.In the present study,however,a quantitative analysis reveals that Li-addition can only slightly stimulate the activation of pyramidal<c+a>slip under compression along the normal direction of a hot-rolled Mg-4.5 wt.%Li plate,with a relative activity of approximately 18%.Although the limited activity of pyramidal<c+a>slip alone cannot accommodate a large plastic strain,it effectively reduces the number of{10.11}−{10.12}double twins,which are believed to be favorable sites for crack initiation.The evidently reduced activity of double twins leads to a lower cracking tendency,and therefore improves ductility.

Coseismic deformation and fault slip distribution of the 2023 M_(W)7.8 and M_(W)7.6 earthquakes in Türkiye

On February 6,2023,a devastating earthquake with a moment magnitude of M_(W)7.8 struck the town of Pazarcik in south-central Türkiye,followed by another powerful earthquake with a moment magnitude of M_(W)7.6 that struck the nearby city of Elbistan 9 h later.To study the characteristics of surface deformation caused by this event and the influence of fault rupture,this study calculated the static coseismic deformation of 56 stations and dynamic displacement waveforms of 15 stations using data from the Turkish national fixed global navigation satellite system(GNSS)network.A maximum static coseismic displacement of 0.38 m for the M_(W)7.8 Kahramanmaras earthquake was observed at station ANTE,36 km from the epicenter,and a maximum dynamic coseismic displacement of 4.4 m for the M_(W)7.6 Elbistan earthquake was observed at station EKZ1,5 km from the epicenter.The rupture-slip distributions of the two earthquakes were inverted using GNSS coseismic deformation as a constraint.The results showed that the Kahramanmaras earthquake rupture segment was distinct and exposed on the ground,resulting in significant rupture slip along the Amanos and Pazarcik fault segments of the East Anatolian Fault.The maximum slip in the Pazarcik fault segment was 10.7 m,and rupture occurred at depths of 0–15 km.In the Cardak fault region,the Elbistan earthquake caused significant ruptures at depths of 0–12 km,with the largest amount of slip reaching 11.6 m.The Coulomb stress change caused by the Kahramanmaras earthquake rupture along the Cardak fault segment was approximately 2 bars,and the area of increased Coulomb stress corresponded to the subsequent rupture region of the M_(W)7.6 earthquake.Thus,it is likely that the M_(W)7.8 earthquake triggered or promoted the M_(W)7.6 earthquake.Based on the cumulative stress impact of the M_(W)7.8 and M_(W)7.6 events,the southwestern segment of the East Anatolian Fault,specifically the Amanos fault segment,experienced a Coulomb rupture stress change exceeding 2 bars,warranting further attention to assess its future seismic hazard risk.

Effect of pre-deformation on precipitation behavior of AZ80 alloy:Comparison of slip-and twinning-dominant deformation

This study investigates the effect of the deformation mode on the precipitation behavior of an extruded Mg-8.0Al-0.5Zn-0.2Mn(AZ80)alloy.The alloy samples are compared after the application of 3.5%tension and 3.5%compression along the extrusion direction to induce slip-dominant and twinning-dominant deformation modes,respectively.The pre-compressed(PC)sample,which contained numerous{10-12}tension twins,has a reduced grain size and a higher internal strain than the pre-tensioned(PT)sample,which is attributed to the inherent internal strain that occurs during the formation and growth of the twins.As a result,the precipitation behavior of the PC sample is accelerated,leading to its short peak aging time of 32 h,which is lower than those of the PT and as-extruded samples(48 and 100 h,respectively).Furthermore,fine continuous precipitates(CPs)rapidly form within the{10-12}twins,contributing to the enhanced hardness.Discontinuous precipitates(DPs),which have a hardness comparable to the CP-containing twinned regions,in the PC sample experience less coarsening during aging than those in the PT sample due to growth inhibition by the{10-12}twins.Ultimately,the{10-12}twins generated under the twinning-dominant deformation condition lead to enhanced precipitation behaviors,including the preferential formation and refinement of CPs and the suppressed coarsening of DPs.Consequently,pre-deformation that occurs{10-12}twinning exhibits more pronounced effects on precipitation acceleration and microstructural modification than slip-inducing pre-deformation.

Experimental investigation on fluid-induced slip behavior of fault filled with fault gouge

Fault zones are usually filled with fault gouge and accompanied by fault water.The coupled effect of fault gouge and water significantly impacts the slip behavior of the fault,which may weaken the fault structure and further induce rupture propagation and earthquakes.In this study,we carried out a laboratory experiment to investigate the fluid-induced slip behavior of fault filled with gouge.The friction evolution characteristic associated with fluid pressure and effective stress was investigated during the slip process.In addition,the role transformation process of the gouge on the slip behavior of fault was revealed.The experimental result indicates that the friction on the filled fault surface is significantly affected by fault gouge.The rupture of the gouge promotes fault slip and the fluid pressure plays a vital role in the initiation of fault slip.The fault gouge enhances the shearing strength of the fault and acts as a barrier before the initial slip under fluid injection.Nevertheless,the fault gouge would accelerate the fault slip and transform into lubricant after the initial slip.

Effect of boundary slip on electroosmotic flow in a curved rectangular microchannel

The aim of this study is to numerically investigate the impact of boundary slip on electroosmotic flow(EOF) in curved rectangular microchannels. Navier slip boundary conditions were employed at the curved microchannel walls. The electric potential distribution was governed by the Poisson–Boltzmann equation, whereas the velocity distribution was determined by the Navier–Stokes equation. The finite-difference method was employed to solve these two equations. The detailed discussion focuses on the impact of the curvature ratio, electrokinetic width, aspect ratio and slip length on the velocity. The results indicate that the present problem is strongly dependent on these parameters. The results demonstrate that by varying the dimensionless slip length from 0.001 to 0.01 while maintaining a curvature ratio of 0.5 there is a twofold increase in the maximum velocity. Moreover, this increase becomes more pronounced at higher curvature ratios. In addition, the velocity difference between the inner and outer radial regions increases with increasing slip length. Therefore, the incorporation of the slip boundary condition results in an augmented velocity and a more non-uniform velocity distribution. The findings presented here offer valuable insights into the design and optimization of EOF performance in curved hydrophobic microchannels featuring rectangular cross-sections.

Co and postseismic fault slip models of the 2022 M_(W)6.7 Menyuan earthquake reveal conjugated faulting tectonics at the central section of the Lenglongling fault

The 2022 M_(W)6.7 Menyuan earthquake ruptured the western end of the Tianzhu seismic gap,providing an opportunity to study the regional seismogenic characteristics and seismic hazards.Here we use interferometric synthetic aperture radar(InSAR)and seismic data to study the mainshock rupture,early afterslip and the second largest aftershock of the 2022 Menyuan earthquake sequences.Our modeling results show that the mainshock ruptured the Lenglongling fault and the Tuolaishan fault with a maximum slip of~3 m.Rapid postseismic transient deformation occurred at the center of the Lenglongling fault.Our afterslip modeling reveals that the majority of afterslip occurred in the deeper part of the Lenglongling fault.A high-angle conjugated faulting event is found at the middle section of the Lenglongling fault.We use the stress inversion to investigate the possible triggering mechanism of the conjugated rupture event.The results indicate the maximum principal stress direction is in~222°,forming a~22°angle between the conjugated fault of second largest aftershock and the mainshock.The calculated normal stress changes indicate the region is within a pull-apart stress field,which favors such a conjugated rupturing event.Our study will help understand the rupture behavior of such kind of conjugated fault in other regions.

Interseismic slip distribution and locking characteristics of the mid-southern segment of the Tanlu fault zone

We employ the block negative dislocation model to invert the distribution of fault coupling and slip rate deficit on the different segments of the Tanlu(Tancheng-Lujiang) fault zone, according to the GPS horizontal velocity field from 1991 to 2007(the first phase) and 2013 to 2018(the second phase). By comparing the deformation characteristics results, we discuss the relationship between the deformation characteristics with the M earthquake in Japan. The results showed that the fault coupling rate of the northern section of Tancheng in the second phase reduced compared with that in the first phase. However, the results of the two phases showed that the northern section of Juxian still has a high coupling rate, a deep blocking depth, and a dextral compressive deficit, which is the enrapture section of the 1668 Tancheng earthquake. At the same time, the area strain results show that the strain rate of the central and eastern regions of the second phase is obviously enhanced compared with that of the first phase. The occurrence of the great earthquake in Japan has played a specific role in alleviating the strain accumulation in the middle and south sections of the Tanlu fault zone. The results of the maximum shear strain show that the shear strain in the middle section of the Tanlu fault zone in the second phase is weaker than that in the first phase, and the maximum shear strain in the southern section is stronger than that in the first phase. The fault coupling coefficient of the south Sihong to Jiashan section is high, and it is also the unruptured section of historical earthquakes. At the same time, small earthquakes in this area are not active and accumulate stress easily, so the future earthquake risk deserves attention.

Risk factors and clinical significance of posterior slip of the proximal vertebral body after lower lumbar fusion

BACKGROUND Adjacent segment disease(ASD)after fusion surgery is frequently manifests as a cranial segment instability,disc herniation,spinal canal stenosis,spondylolisthesis or retrolisthesis.The risk factors and mechanisms of ASD have been widely discussed but never clearly defined.AIM To investigate the risk factors and clinical significance of retrograde movement of the proximal vertebral body after lower lumbar fusion.METHODS This was a retrospective analysis of the clinical data of patients who underwent transforaminal lumbar interbody fusion surgery between September 2015 and July 2021 and who were followed up for more than 2 years.Ninety-one patients with degenerative lumbar diseases were included(22 males and 69 females),with an average age of 52.3 years(40-73 years).According to whether there was retrograde movement of the adjacent vertebral body on postoperative X-rays,the patients were divided into retrograde and nonretrograde groups.The sagittal parameters of the spine and pelvis were evaluated before surgery,after surgery,and at the final follow-up.At the same time,the Oswestry Disability Index(ODI)and Visual Analogue Scale(VAS)were used to evaluate the patients’quality of life.RESULTS Nineteen patients(20.9%)who experienced retrograde movement of proximal adjacent segments were included in this study.The pelvic incidence(PI)of the patients in the retrograde group were significantly higher than those of the patients in the nonretrograde group before surgery,after surgery and at the final follow-up(P<0.05).There was no significant difference in lumbar lordosis(LL)between the two groups before the operation,but LL in the retrograde group was significantly greater than that in the nonretrograde group postoperatively and at the final follow-up.No significant differences were detected in terms of the|PI–LL|,and there was no significant difference in the preoperative lordosis distribution index(LDI)between the two groups.The LDIs of the retrograde group were 68.1%±11.5%and 67.2%±11.9%,respectively,which were significantly lower than those of the nonretrograde group(75.7%±10.4%and 74.3%±9.4%,respectively)(P<0.05).Moreover,the patients in the retrograde group had a greater incidence of a LDI<50%than those in the nonretrograde group(P<0.05).There were no significant differences in the ODI or VAS scores between the two groups before the operation,but the ODI and VAS scores in the retrograde group were significantly worse than those in the nonretrograde group after the operation and at the last follow-up,(P<0.05).CONCLUSION The incidence of posterior slippage after lower lumbar fusion was approximately 20.9%.The risk factors are related to a higher PI and distribution of lumbar lordosis.When a patient has a high PI and insufficient reconstruction of the lower lumbar spine,adjacent segment compensation via posterior vertebral body slippage is one of the factors that significantly affects surgical outcomes.

Wall slip behavior of cemented paste backfill slurry during pipeline based on noncontact experimental detection

Wall slip is a microscopic phenomenon of cemented paste backfill(CPB)slurry near the pipe wall,which has an important influence on the form of slurry pipe transport flow and velocity distribution.Directly probing the wall slip characteristics using conventional experimental methods is difficult.Therefore,this paper established a noncontact experimental platform for monitoring the microscopic slip layer of CPB pipeline transport independently based on particle image velocimetry(PIV)and analyzed the effects of slurry temperature,pipe diameter,solid concentration,and slurry flow on the wall slip velocity of the CPB slurry,which refined the theory of the effect of wall slip characteristics on pipeline transport.The results showed that the CPB slurry had an extensive slip layer at the pipe wall with significant wall slip.High slurry temperature improved the degree of particle Brownian motion within the slurry and enhanced the wall slip effect.Increasing the pipe diameter was not conducive to the formation of the slurry slip layer and led to a transition in the CPB slurry flow pattern.The increase in the solid concentration raised the interlayer shear effect of CPB slurry flow and the slip velocity.The slip velocity value increased from 0.025 to 0.056 m·s^(-1)when the solid content improved from 55wt%to 65wt%.When slurry flow increased,the CPB slurry flocculation structure changed,which affected the slip velocity,and the best effect of slip layer resistance reduction was achieved when the transported flow rate was 1.01 m^(3)·h^(-1).The results had important theoretical significance for improving the stability and economy of the CPB slurry in the pipeline.

Loading direction dependence of asymmetric response of pyramidal slip in rolled AZ31 magnesium alloy

Textured magnesium alloys usually exhibit anisotropic mechanical behavior due to the asymmetric activation of different twinning and slipping modes.This work focuses on the pyramidal slip responses of rolled AZ31 magnesium alloy under two loading conditions,compressive and tensile loading along the normal direction.Under the condition where the compressive loading direction is closely parallel to the c-axis of the unit cell,tensile twinning and basal slips are prohibited, dislocations then active and tend to accumulate at grain boundaries and form dislocation walls.Meanwhile,these dislocations exhibit zigzag morphologies,which result from the cross-slip from {10■1} first-order pyramidal plane to {11■2} second-order pyramidal plane,then back to {10■1} first-order pyramidal plane.Under the condition where tensile twins are prevalent,{10■1} first-order and {11■2} second-order pyramidal dislocations are favorable to be activated.Both types of dislocations behave climb-like dissociations onto the basal plane,forming zigzag dislocations.

Underlying slip/twinning activities of Mg-xGd alloys investigated by modified lattice rotation analysis

The inconsistencies regarding the fundamental correlation between Gd content and slip(twinning)activities of Mg alloys appeal further investigations.However,the traditional slip dislocations analysis by TEM is time-consuming,and that by SEM/EBSD cannot recognize the partial slip modes.These urge a more efficient and comprehensive approach to easily distinguish all potential slip modes occurred concurrently in alloy matrix.Here we report a modified lattice rotation analysis that can distinguish all slip systems and provide statistical results for slip activities in Mg alloy matrix.Using this method,the high ductility of Mg-Gd alloy ascribed to the enhanced non-basal slips,cross-slip,and postponed twinning activities by Gd addition is quantitatively clarified.

On the strengthening and slip activity of Mg-3Al-1Zn alloy with pre-induced{1012¯}twins

{1012¯}twins were introduced into the magnesium(Mg)plate AZ31 via pre-rolling along its transverse direction.The plates,both with and without the pre-induced{1012¯}twins,were subjected to uniaxial tension along different directions.Using crystal plasticity modeling,we found that the strengthening effect of the pre-induced{1012¯}twins on the macroscopic flow stress primarily arised from the increased slip resistance caused by the boundaries,rather than the orientation hardening due to the twinning reorientation(although the latter did make its contribution in some specific loading directions).Besides,the pre-existing{1012¯}twins were found,by both experiments and simulation,to promote the activity of prismatic and pyramidal<c+a>in the parent matrix of the material.Further analysis showed that the enhanced non-basal slip activity is related to the{1012¯}twin boundaries’low micro Hall-Petch slope ratios of non-basal slips to basal slip.With the critical resolved shear stress(CRSS)obtained from crystal plasticity modeling and the orientation data from EBSD,a probability-based slip transfer model was proposed.The model predicts higher slip transfer probabilities and thus lower strain concentration tendencies at{1012¯}twin boundaries than that at grain boundaries,which agrees with the experimental observation that the strain localization was primarily associated with the latter.The present findings are helpful scientifically,in deepening our understanding of how the pre-induced{1012¯}twins affect the strength and slip activity of Mg alloys,and technologically,in guiding the design of the pre-strain protocol of Mg alloys.

Experimental study on the slip evolution of planar fractures subjected to cyclic normal stress

The frictional rupture mechanisms of rock discontinuities considering the dynamic load disturbance still remain unclear.This paper investigates the transitional behaviors of slip events happened on a planar granite fracture under cyclic normal stress with diferent oscillation amplitudes.The experimental results show that the activations of fast slips always correlate with unloading of normal stress.Besides,the intensive normal stress oscillation can weaken the shear strength which is recoverable when the normal stress return to constant.The rupture patterns are quantifed by stress drop,slip length and slip velocity.With the efect of small oscillation amplitudes,the slip events show chaotic shapes,compared to the regular and predictable style under constant normal stress.When the amplitude is large enough,the big and small slip events emerge alternately,showing a compound slip style.Large amplitude of the cyclic normal stress also widens the interval diferences of the slip events.This work provides experimental supports for a convincible link between the dynamic stress disturbance and the slip behavior of rock fractures.

Transient postseismic slip and aftershock triggering:A case study of the 2008 M_W7.9 Wenchuan Earthquake,China

In this study,we investigate how a stress variation generated by a fault that experiences transient postseismic slip(TPS)affects the rate of aftershocks.First,we show that the postseismic slip from Rubin-Ampuero model is a TPS that can occur on the main fault with a velocity-weakening frictional motion,that the resultant slip function is similar to the generalized Jeffreys-Lomnitz creep law,and that the TPS can be explained by a continuous creep process undergoing reloading.Second,we obtain an approximate solution based on the Helmstetter-Shaw seismicity model relating the rate of aftershocks to such TPS.For the Wenchuan sequence,we perform a numerical fitting of the cumulative number of aftershocks using the Modified Omori Law(MOL),the Dieterich model,and the specific TPS model.The fitting curves indicate that the data can be better explained by the TPS model with a B/A ratio of approximately 1.12,where A and B are the parameters in the rate-and state-dependent friction law respectively.Moreover,the p and c that appear in the MOL can be interpreted by the B/A and the critical slip distance,respectively.Because the B/A ratio in the current model is always larger than 1,the model could become a possible candidate to explain aftershock rate commonly decay as a power law with a p-value larger than 1.Finally,the influence of the background seismicity rate r on parameters is studied;the results show that except for the apparent aftershock duration,other parameters are insensitive to r.

Origin of nucleation and growth of extension twins in grains unsuitably oriented for twinning during deformation of Mg-1%Al

A large number of anomalous extension twins,with low or even negative twinning Schmid factors,were found to nucleate and grow in a strongly textured Mg-1Al alloy during tensile deformation along the extruded direction.The deformation mechanisms responsible for this behaviour were investigated through in-situ electron back-scattered diffraction,grain reference orientation deviation,and slip trace-modified lattice rotation.It was found that anomalous extension twins nucleated mainly at the onset of plastic deformation at or near grain boundary triple junctions.They were associated with the severe strain incompatibility between neighbour grains as a result from the differentbasal slip-induced lattice rotations.Moreover,the anomalous twins were able to grow with the applied strain due to the continuous activation ofbasal slip in different neighbour grains,which enhanced the strain incompatibility.These results reveal the complexity of the deformation mechanisms in Mg alloys at the local level when deformed along hard orientations.

足式机器人SLIP模型向上跳跃台阶的运动控制

由于存在地势起伏,台阶对足式机器人运动稳定性会带来较大挑战.弹簧负载倒立摆模型(SLIP)作为研究足式机器人的优良模板,能否完成向上跳跃台阶的动作与其腿部摆角,起跳位置和跳跃高度都有密切的关系.由于调整模型腿部摆角规律容易引发运动失效,故本文在算法中引入虚拟弹簧腿,根据虚拟弹簧腿的运行规律确定合理起跳位置,根据起跳位置来控制系统跳跃高度进而完成跳跃台阶的动作.最后利用仿真软件进行多组仿真,结果表明本文算法对起跳区间划分合理,对起跳高度控制精准,能够实现SLIP模型跳跃台阶前后的稳定运动.

Effects of temperature on critical resolved shear stresses of slip and twining in Mg single crystal via experimental and crystal plasticity modeling

Magnesium(Mg)single crystal specimens with three different orientations were prepared and tested from room temperature to 733 K in order to systematically evaluate effects of temperature on the critical resolved shear stress(CRSS)of slips and twinning in Mg single crystals.The duplex non-basal slip took place in the temperature range from 613 to 733 K when the single crystal samples were stretched along the<0110>direction.In contrast,the single basal slip and prismatic slip were mainly activated in the temperature range from RT to 733 K when the tensile directions were inclined at an angle of 45°with the basal and the prismatic plane,respectively.Viscoplastic self-consistent(VPSC)crystal modeling simulations with genetic algorithm code(GA-code)were carried out to obtain the best fitted CRSSs of major deformation modes,such as basal slip,prismatic slip,pyramidalⅡ,{1012}tensile twinning and{1011}compressive twinning when duplex slips accommodated deformation.Additionally,CRSSs of the basal and the prismatic slip were derived using the Schmid factor(SF)criterion when the single slip mainly accommodated deformation.From the CRSSs of major deformation modes obtained by the VPSC simulations and the SF calculations,the CRSSs for basal slip and{1012}tensile twinning were found to show a weak temperature dependence,whereas those for prismatic,slip and{1011}compressive twinning exhibited a strong temperature dependence.From the comparison of previous results,VPSC-GA modeling was proved to be an effective method to obtain the CRSSs of various deformation modes of Mg and its alloys.

Stability Scrutinization of Agrawal Axisymmetric Flow of Nanofluid through a Permeable Moving Disk Due to Renewable Solar Radiation with Smoluchowski Temperature and Maxwell Velocity Slip Boundary Conditions

The utilization of solar energy is essential to all living things since the beginning of time.In addition to being a constant source of energy,solar energy(SE)can also be used to generate heat and electricity.Recent technology enables to convert the solar energy into electricity by using thermal solar heat.Solar energy is perhaps the most easily accessible and plentiful source of sustainable energy.Copper-based nanofluid has been considered as a method to improve solar collector performance by absorbing incoming solar energy directly.The goal of this research is to explore theoretically the Agrawal axisymmetric flow induced by Cu-water nanofluid over a moving permeable disk caused by solar energy.Moreover,the impacts of Maxwell velocity and Smoluchowski temperature slip are incorporated to discuss the fine points of nanofluid flow and characteristics of heat transfer.The primary partial differential equations are transformed to similarity equations by employing similarity variables and then utilizing bvp4c to resolve the set of equations numerically.The current numerical approach can produce double solutions by providing suitable initial guesses.In addition,the results revealed that the impact of solar collector efficiency enhances significantly due to nanoparticle volume fraction.The suction parameter delays the boundary layer separation.Moreover,stability analysis is performed and is found that the upper solution is stable and physically trustworthy while the lower one is unstable.

液体润滑浸渍表面(SLIPS)船舶防污涂层最新研究进展

综述了近3年来关于液体润滑浸渍表面(SLIPS)船舶防污涂层的研究进展,特别是润滑液的选择与涂层的结构设计,以及这些因素如何影响涂层的整体性能,以期为未来的研究提供最新思路及研究方法。

Slip boundary effect on the critical Reynolds number of subcritical transition in channel flow

In this letter,the effect of slip boundary on the origin of subcritical transition in two-dimensional chan-nel flows is studied numerically and theoretically.It is shown that both the positive and the negative slip lengths will increase the critical Reynolds number of localized wave packet and hence postpone the transition.By applying a variable transformation and expanding the variables about a small slip length,it is illustrated that the slip boundary effect only exists in the second and higher order modulations of the no-slip solution,and hence explains the power law found in simulations,i.e.the relative increment of the critical Reynolds number due to the slip boundary is proportional to the square of the slip length.