The development of a possible slip line field (slf) for theoretical calculations of the deforming pressure (load) in a second pass of a lubricated cold rolling sheet mill and validation using values from an aluminium ...The development of a possible slip line field (slf) for theoretical calculations of the deforming pressure (load) in a second pass of a lubricated cold rolling sheet mill and validation using values from an aluminium sheet rolling mill was done in this work. This will be relevant in the manufacturing industries providing an easy method for determining necessary applied rolling load. Experimental rolling was carried out to observe the shear lines in the deformation field. Construction of possible slip line field model was developed adhering strictly to assumptions of rigid plastic model. Calculation of the deforming force/load was achieved using Hencky’s equation. Results showed that the load calculations for constructed slip line field using aluminium sheet rolling as an example tallied with values obtained from Tower Aluminium rolling mill. Slip line fields constructed for the second pass described adequately the rolling pressure in the cold rolling process, giving a valid solution of the exact load estimates on comparison with the industrial load values. Roll pressure along the arc of contact rose fairly linearly from the entrance to a maximum at the exit point. This work showed that slf for the first pass in a cold rolling mill cannot be used for subsequent passes;it requires construction of slfs for each pass in the cold rolling process.展开更多
The solid-liquid interface, which is ubiquitous in nature and our daily life, plays fundamental roles in a variety of physical-chemical-biological- mechanical phenomena, for example in lubrication, crystal growth, and...The solid-liquid interface, which is ubiquitous in nature and our daily life, plays fundamental roles in a variety of physical-chemical-biological- mechanical phenomena, for example in lubrication, crystal growth, and many biological reactions that govern the building of human body and the functioning of brain. A surge of interests in the moving contact line （MCL） problem, which is still going on today, can be traced back to 1970s primarily because of the exis- tence of the ＂Huh-Scriven paradox＂. This paper, mainly from a solid mechanics perspective, describes very briefly the multidisciplinary nature of the MCL problem, then summarizes some major advances in this exciting research area, and some future directions are presented.展开更多
以79g/mm的中阶梯衍射光栅为目标,研究衍射光栅机械刻划过程中铝膜的槽形隆起机制。首先,经过4次坐标变换,建立了光栅槽形的塑流剖面。然后,基于Lee and Shaffer提出的滑移线场模型,在塑流剖面内建立起包含滞留区域的滑移现场模型,并根...以79g/mm的中阶梯衍射光栅为目标,研究衍射光栅机械刻划过程中铝膜的槽形隆起机制。首先,经过4次坐标变换,建立了光栅槽形的塑流剖面。然后,基于Lee and Shaffer提出的滑移线场模型,在塑流剖面内建立起包含滞留区域的滑移现场模型,并根据Dewhurst and Collins提出的矩阵算法对滑移线场进行求解,最终得到槽形隆起尺寸模型。最后,通过DEFORM软件对槽形隆起尺寸的演变规律进行模拟分析。展开更多
The model test result of earth force in the side of anti-slide pile of anchor bars was introduced.There are three groups of the tests.The loads were on the back side of the slope in two groups.The other one was loaded...The model test result of earth force in the side of anti-slide pile of anchor bars was introduced.There are three groups of the tests.The loads were on the back side of the slope in two groups.The other one was loaded just behind the pile by the jack.In order to get the force of the soil,some earth-pressure boxes were used to get the earth pressure on the side of the piles.The part of the max pressure and the earth pressure was mainly focused under the slip line展开更多
文摘The development of a possible slip line field (slf) for theoretical calculations of the deforming pressure (load) in a second pass of a lubricated cold rolling sheet mill and validation using values from an aluminium sheet rolling mill was done in this work. This will be relevant in the manufacturing industries providing an easy method for determining necessary applied rolling load. Experimental rolling was carried out to observe the shear lines in the deformation field. Construction of possible slip line field model was developed adhering strictly to assumptions of rigid plastic model. Calculation of the deforming force/load was achieved using Hencky’s equation. Results showed that the load calculations for constructed slip line field using aluminium sheet rolling as an example tallied with values obtained from Tower Aluminium rolling mill. Slip line fields constructed for the second pass described adequately the rolling pressure in the cold rolling process, giving a valid solution of the exact load estimates on comparison with the industrial load values. Roll pressure along the arc of contact rose fairly linearly from the entrance to a maximum at the exit point. This work showed that slf for the first pass in a cold rolling mill cannot be used for subsequent passes;it requires construction of slfs for each pass in the cold rolling process.
基金supported by the National Natural Science Foundation of China(11372313)the Key Research Program of the Chinese Academy of Sciences(KJZD-EW-M01)+1 种基金the Instrument Developing Project ofthe CAS(Y2010031)the CAS/SAFEA International Partnership Program for Creative Research Teams
文摘The solid-liquid interface, which is ubiquitous in nature and our daily life, plays fundamental roles in a variety of physical-chemical-biological- mechanical phenomena, for example in lubrication, crystal growth, and many biological reactions that govern the building of human body and the functioning of brain. A surge of interests in the moving contact line （MCL） problem, which is still going on today, can be traced back to 1970s primarily because of the exis- tence of the ＂Huh-Scriven paradox＂. This paper, mainly from a solid mechanics perspective, describes very briefly the multidisciplinary nature of the MCL problem, then summarizes some major advances in this exciting research area, and some future directions are presented.
文摘以79g/mm的中阶梯衍射光栅为目标,研究衍射光栅机械刻划过程中铝膜的槽形隆起机制。首先,经过4次坐标变换,建立了光栅槽形的塑流剖面。然后,基于Lee and Shaffer提出的滑移线场模型,在塑流剖面内建立起包含滞留区域的滑移现场模型,并根据Dewhurst and Collins提出的矩阵算法对滑移线场进行求解,最终得到槽形隆起尺寸模型。最后,通过DEFORM软件对槽形隆起尺寸的演变规律进行模拟分析。
文摘The model test result of earth force in the side of anti-slide pile of anchor bars was introduced.There are three groups of the tests.The loads were on the back side of the slope in two groups.The other one was loaded just behind the pile by the jack.In order to get the force of the soil,some earth-pressure boxes were used to get the earth pressure on the side of the piles.The part of the max pressure and the earth pressure was mainly focused under the slip line
