Revealing the role of pyramidal slip in the high ductility of Mg-Li alloy

The high ductility of Mg-Li alloy has been mainly ascribed to a high activity of pyramidal<c+a>slip to accommodate plastic strain.In the present study,however,a quantitative analysis reveals that Li-addition can only slightly stimulate the activation of pyramidal<c+a>slip under compression along the normal direction of a hot-rolled Mg-4.5 wt.%Li plate,with a relative activity of approximately 18%.Although the limited activity of pyramidal<c+a>slip alone cannot accommodate a large plastic strain,it effectively reduces the number of{10.11}−{10.12}double twins,which are believed to be favorable sites for crack initiation.The evidently reduced activity of double twins leads to a lower cracking tendency,and therefore improves ductility.

Origin of nucleation and growth of extension twins in grains unsuitably oriented for twinning during deformation of Mg-1%Al

A large number of anomalous extension twins,with low or even negative twinning Schmid factors,were found to nucleate and grow in a strongly textured Mg-1Al alloy during tensile deformation along the extruded direction.The deformation mechanisms responsible for this behaviour were investigated through in-situ electron back-scattered diffraction,grain reference orientation deviation,and slip trace-modified lattice rotation.It was found that anomalous extension twins nucleated mainly at the onset of plastic deformation at or near grain boundary triple junctions.They were associated with the severe strain incompatibility between neighbour grains as a result from the differentbasal slip-induced lattice rotations.Moreover,the anomalous twins were able to grow with the applied strain due to the continuous activation ofbasal slip in different neighbour grains,which enhanced the strain incompatibility.These results reveal the complexity of the deformation mechanisms in Mg alloys at the local level when deformed along hard orientations.

足式机器人SLIP模型向上跳跃台阶的运动控制

由于存在地势起伏,台阶对足式机器人运动稳定性会带来较大挑战.弹簧负载倒立摆模型(SLIP)作为研究足式机器人的优良模板,能否完成向上跳跃台阶的动作与其腿部摆角,起跳位置和跳跃高度都有密切的关系.由于调整模型腿部摆角规律容易引发运动失效,故本文在算法中引入虚拟弹簧腿,根据虚拟弹簧腿的运行规律确定合理起跳位置,根据起跳位置来控制系统跳跃高度进而完成跳跃台阶的动作.最后利用仿真软件进行多组仿真,结果表明本文算法对起跳区间划分合理,对起跳高度控制精准,能够实现SLIP模型跳跃台阶前后的稳定运动.

Coseismic deformation and fault slip distribution of the 2023 M_(W)7.8 and M_(W)7.6 earthquakes in Türkiye

On February 6,2023,a devastating earthquake with a moment magnitude of M_(W)7.8 struck the town of Pazarcik in south-central Türkiye,followed by another powerful earthquake with a moment magnitude of M_(W)7.6 that struck the nearby city of Elbistan 9 h later.To study the characteristics of surface deformation caused by this event and the influence of fault rupture,this study calculated the static coseismic deformation of 56 stations and dynamic displacement waveforms of 15 stations using data from the Turkish national fixed global navigation satellite system(GNSS)network.A maximum static coseismic displacement of 0.38 m for the M_(W)7.8 Kahramanmaras earthquake was observed at station ANTE,36 km from the epicenter,and a maximum dynamic coseismic displacement of 4.4 m for the M_(W)7.6 Elbistan earthquake was observed at station EKZ1,5 km from the epicenter.The rupture-slip distributions of the two earthquakes were inverted using GNSS coseismic deformation as a constraint.The results showed that the Kahramanmaras earthquake rupture segment was distinct and exposed on the ground,resulting in significant rupture slip along the Amanos and Pazarcik fault segments of the East Anatolian Fault.The maximum slip in the Pazarcik fault segment was 10.7 m,and rupture occurred at depths of 0–15 km.In the Cardak fault region,the Elbistan earthquake caused significant ruptures at depths of 0–12 km,with the largest amount of slip reaching 11.6 m.The Coulomb stress change caused by the Kahramanmaras earthquake rupture along the Cardak fault segment was approximately 2 bars,and the area of increased Coulomb stress corresponded to the subsequent rupture region of the M_(W)7.6 earthquake.Thus,it is likely that the M_(W)7.8 earthquake triggered or promoted the M_(W)7.6 earthquake.Based on the cumulative stress impact of the M_(W)7.8 and M_(W)7.6 events,the southwestern segment of the East Anatolian Fault,specifically the Amanos fault segment,experienced a Coulomb rupture stress change exceeding 2 bars,warranting further attention to assess its future seismic hazard risk.

液体润滑浸渍表面(SLIPS)船舶防污涂层最新研究进展

综述了近3年来关于液体润滑浸渍表面(SLIPS)船舶防污涂层的研究进展,特别是润滑液的选择与涂层的结构设计,以及这些因素如何影响涂层的整体性能,以期为未来的研究提供最新思路及研究方法。

The Channel Branches & Network Vessels on the Tianhui Lacquered Meridian Figurine——Taking the Heart-Regulated Channel as an Example

Along with the surge of unearthed medical literature and cultural relics in recent years,a network of channels in the system of medical conduit vessels(meridians) during the early Western Han dynasty has become much clearer gradually.In it,the increasing number of channel branches,network vessels and needle insertion holes(acupoints) is an important feature of the development of channel medicine during the Western Han dynasty.This is not only a reflection of the expanding requirements of the theoretical system of the main trunk channels and other vessels,but also an inevitable result of the continuous enrichment and accumulation of clinical experience.This article integrates the information about channel branches,network vessels,inscriptions,dots and further relics on the Tianhui(天回) Lacquered Meridian Figurine to compare the unearthed literature of the channel genre with the transmitted classical literature about acupuncture.The “Heart-Regulated Channel” in Medical Manuscripts on Bamboo Slips from Tianhui(《天回医简》) serves as an example to explain the occurrence,development and changes of the channel branches and network vessels in the early system of medical channels.

Co-seismic surface displacement of the June 21, 2022 M_(W)6 Khōst,Afghanistan earthquake from InSAR observations

A robust estimation of the earthquake location, seismic moment, and fault geometry is essential for objective seismic hazard assessment. Seismic events in a remote location, specifically in the absence of seismic and GNSS networks, can be investigated effectively using the In SAR-based technique. This study adopts the Differential Interferometric SAR(DIn SAR) technique to quantify the co-seismic surface displacement caused by the June 21, 2022, Khōst M_(W)6 earthquake that occurred along the western plate boundary between the Indian and Eurasian plate. The interferograms show that the maximum surface deformation occurred on the northwest and southwest of the fault line. From coherence, the Line of Sight(LOS) displacement, and the co-seismic surface displacement analysis, it has been observed that surface deformation was most pronounced in the southwest region of the fault line, and the surface has moved to the opposite direction along the fault line, which indicates a sinistral slightly oblique strike-slip movement. This In SAR-based observation appears consistent with the seismic waveforms derived from co-seismic surface displacements. Further, it has been argued that the slip deficit accumulated during the period of the last about 48 years along the frontal region of the northward extension of the Suleiman range and associated fault zone is qualitatively estimated at about 1.5 m, which is consistent with the seismic waveforms derived finite slip model.

Experimental investigation on fluid-induced slip behavior of fault filled with fault gouge

Fault zones are usually filled with fault gouge and accompanied by fault water.The coupled effect of fault gouge and water significantly impacts the slip behavior of the fault,which may weaken the fault structure and further induce rupture propagation and earthquakes.In this study,we carried out a laboratory experiment to investigate the fluid-induced slip behavior of fault filled with gouge.The friction evolution characteristic associated with fluid pressure and effective stress was investigated during the slip process.In addition,the role transformation process of the gouge on the slip behavior of fault was revealed.The experimental result indicates that the friction on the filled fault surface is significantly affected by fault gouge.The rupture of the gouge promotes fault slip and the fluid pressure plays a vital role in the initiation of fault slip.The fault gouge enhances the shearing strength of the fault and acts as a barrier before the initial slip under fluid injection.Nevertheless,the fault gouge would accelerate the fault slip and transform into lubricant after the initial slip.

Research on casing deformation prevention technology based on cementing slurry system optimization

The casing deformation prevention technology based on the optimization of cement slurry is proposed to reduce the casing deformation of shale oil and gas wells during hydraulic fracturing. In this paper, the fracture mechanism of hollow particles in cement sheath was firstly analyzed by discrete element method, and the effect of hollow particles in cement on casing deformation was investigated by laboratory experiment method. Finally, field test was carried out to verify the improvement effect of the casing deformation based on cement slurry modification. The results show that the formation displacement can be absorbed effectively by hollow particles inside the cement transferring the excessive deformation away from casing. The particles in the uncemented state provide deformation space during formation slipping. The casing with diameter of 139.7 mm could be passed through by bridge plug with the diameter of 99 mm when the mass ratio of particle/cement reaches 1:4. According to the field test feedback, the method based on optimization of cement slurry can effectively reduce the risk of casing deformation, and the recommended range of hollow microbeads content in the cement slurry is between 15% and 25%.

Unveiling the rolling texture variations ofα-Mg phases in a dual-phase Mg-Li alloy

LZ91 Mg-Li alloy plates with three types of initial texture were rolled by 70%reduction at both room temperature and 200℃to explore the rolling texture formation ofα-Mg phase.The results showed that the rolling texture is largely affected by the initial texture.All the samples exhibited two main texture components as RD-split double peaks texture and TD-split double peaks texture after large strain rolling.The intensity of the two texture components was strongly influenced by the initial orientation and rolling temperature.Extension twinning altered the large-split non-basal orientation to a near basal one at low rolling strain.The basal orientation induced by twinning is unstable,which finally transmitted to the RD-split texture.The strong TD-split texture formed due to slip-induced orientation transition from its initial orientation.The competition between prismatic and basal slip determined the intensity and tilt angle of the TD-split texture.By increasing the rolling temperature,the TD-split texture component was enhanced in all three samples.Limitation of extension twinning behavior and the promotion of prismatic slip at elevated temperature are the main reasons for the difference in hot and cold rolling texture.

Present-day movement characteristics of the Qinghai Nanshan fault and its surrounding area from GPS observation

The Qinghai Nanshan fault is a larger fault in the Northeastern Xizang Plateau.In previous studies,its movement characteristics are mainly investigated with geological and seismic observations,and the tectonic transformation role of the fault on its east is not yet clear.This study uses data fusion to obtain denser GPS observations near the Qinghai Nanshan fault.Based on tectonic characteristics,we establish a block model to investigate the fault slip rate,locking degree,and slip deficit.The results show that the Qinghai Nanshan fault slip rate is characterized by sinistral and convergent movement.Both the sinistral and convergent rates display a decreasing trend from west to east.The locking degree and slip deficit are higher in the western segment(with an average of about 0.74 and 1.1 mm/a)and lower in the eastern segment.Then,we construct a strain rate field using GPS observations to analyze the regional strain characteristics.The results indicate that along the fault,the western segment shows a larger shear strain rate and negative dilation rate.Regional earthquake records show that the frequency of earthquakes is lower near the fault.The joint results suggest that the western segment may have a higher earthquake risk.In addition,the insignificant fault slip rate in the eastern segment may indicate that it does not participate in the tectonic transformation among the Riyueshan,Lajishan,and West Qinling faults.

Effect of wire diameter compression ratio on drawing deformation of micro copper wire

A crystal plasticity finite element model was developed for the drawing deformation of pure copper micro wire,based on rate-dependent crystal plasticity theory.The impact of wire diameter compression ratio on the micro-mechanical deformation behavior during the wire drawing process was investigated.Results indicate that the internal deformation and slip of the drawn wire are unevenly distributed,forming distinct slip and non-slip zones.Additionally,horizontal strain concentration bands develop within the drawn wire.As the wire diameter compression ratio increases,the strength of the slip systems and the extent of slip zones inside the deformation zone also increase.However,the fluctuating stress state,induced by contact pressure and frictional stress,results in a rough and uneven wire surface and diminishes the stability of the drawing process.

Analysis of deformation mechanisms in magnesium single crystals using a dedicated four-point bending tester

In this study,we explored the deformation mechanisms of Mg single crystals using a combination of scanning electron microscopy and electron backscattered diffraction in conjunction with a dedicated four-point bending tester.We prepared two single-crystal samples,oriented along the<1120>and<1010>directions,to assess the mechanisms of deformation when the initial basal slip was suppressed.In the<1120>sample,the primary{1012}twin(T1)was confirmed along the<1120>direction of the sample on the compression side with an increase in bending stress.In the<1010>sample,T1 and the secondary twin(T2)were confirmed to be along the<1120>direction,with an orientation of±60°with respect to the bending stress direction,and their direction matched with(0001)in T1 and T2.This result implies that crystallographically,the basal slip occurs readily.In addition,the<1010>sample showed the double twin in T1 on the compression side and the tertiary twin along the<1010>direction on the tension side.These results demonstrated that the maximum bending stress and displacement changed significantly under the bend loading because the deformation mechanisms were different for these single crystals.Therefore,the correlation between bending behavior and twin orientation was determined,which would be helpful for optimizing the bending properties of Mg-based materials.

Influence of Brownian Motion, Thermophoresis and Magnetic Effects on a Fluid Containing Nanoparticles Flowing over a Stretchable Cylinder

The influence of Brownian motion and thermophoresis on a fluid containing nanoparticles flowing over a stretchable cylinder is examined.The classical Navier-Stokes equations are considered in a porous frame.In addition,the Lorentz force is taken into account.The controlling coupled nonlinear partial differential equations are transformed into a system of first order ordinary differential equations by means of a similarity transformation.The resulting system of equations is solved by employing a shooting approach properly implemented in MATLAB.The evolution of the boundary layer and the growing velocity is shown graphically together with the related profiles of concentration and temperature.The magnetic field has a different influence(in terms of trends)on velocity and concentration.

Computational Investigation of Brownian Motion and Thermophoresis Effect on Blood-Based Casson Nanofluid on a Non-linearly Stretching Sheet with Ohmic and Viscous Dissipation Effects

Motivated by the widespread applications of nanofluids,a nanofluid model is proposed which focuses on uniform magnetohydrodynamic(MHD)boundary layer flow over a non-linear stretching sheet,incorporating the Casson model for blood-based nanofluid while accounting for viscous and Ohmic dissipation effects under the cases of Constant Surface Temperature(CST)and Prescribed Surface Temperature(PST).The study employs a twophase model for the nanofluid,coupled with thermophoresis and Brownian motion,to analyze the effects of key fluid parameters such as thermophoresis,Brownian motion,slip velocity,Schmidt number,Eckert number,magnetic parameter,and non-linear stretching parameter on the velocity,concentration,and temperature profiles of the nanofluid.The proposed model is novel as it simultaneously considers the impact of thermophoresis and Brownian motion,along with Ohmic and viscous dissipation effects,in both CST and PST scenarios for blood-based Casson nanofluid.The numerical technique built into MATLAB’s bvp4c module is utilized to solve the governing system of coupled differential equations,revealing that the concentration of nanoparticles decreases with increasing thermophoresis and Brownian motion parameters while the temperature of the nanofluid increases.Additionally,a higher Eckert number is found to reduce the nanofluid temperature.A comparative analysis between CST and PST scenarios is also undertaken,which highlights the significant influence of these factors on the fluid’s characteristics.The findings have potential applications in biomedical processes to enhance fluid velocity and heat transfer rates,ultimately improving patient outcomes.

Effect of boundary slip on electroosmotic flow in a curved rectangular microchannel

The aim of this study is to numerically investigate the impact of boundary slip on electroosmotic flow(EOF) in curved rectangular microchannels. Navier slip boundary conditions were employed at the curved microchannel walls. The electric potential distribution was governed by the Poisson–Boltzmann equation, whereas the velocity distribution was determined by the Navier–Stokes equation. The finite-difference method was employed to solve these two equations. The detailed discussion focuses on the impact of the curvature ratio, electrokinetic width, aspect ratio and slip length on the velocity. The results indicate that the present problem is strongly dependent on these parameters. The results demonstrate that by varying the dimensionless slip length from 0.001 to 0.01 while maintaining a curvature ratio of 0.5 there is a twofold increase in the maximum velocity. Moreover, this increase becomes more pronounced at higher curvature ratios. In addition, the velocity difference between the inner and outer radial regions increases with increasing slip length. Therefore, the incorporation of the slip boundary condition results in an augmented velocity and a more non-uniform velocity distribution. The findings presented here offer valuable insights into the design and optimization of EOF performance in curved hydrophobic microchannels featuring rectangular cross-sections.

Source parameters and aftershock pattern of the October 7,2021,M5.9 Harnai earthquake,Pakistan

On October 7,2021,a magnitude 5.9 earthquake struck the Harnai(Baluchistan)region of Pakistan,causing several fatalities and injuries within the epicentral area.First-order tectonic deformation in this region is caused by the convergence of the Indian Plate with respect to the Eurasian Plate.The Katwaz Block hinders the motion of the Indian Plate,resulting in the formation of strike-slip faults.In this study,the P-wave first-motion polarity technique was used to determine the mainshock faulting style.Cyclic scanning of the polarity solutions was applied to determine the most suitable focal mechanism solution among the available solutions generated by the FOCMEC(focal mechanism)software.The nodal planes correspond to different faulting styles(i.e.,thrust and strike-slip faulting).A nodal plane oriented in the NW-SE direction corresponded to a strike-slip mechanism,which was considered to be the fault plane.Tectonically,this earthquake was associated with the Harnai-Karahi strike-slip fault zone owing to the fault strike and direction of slip.The apparent stress drop,fault length,and moment magnitude of the Harnai earthquake were 35.4 bar,6.1 km,and 5.9,respectively.A lower b-value for the Gutenberg-Richter law was observed prior to the earthquake.Higherα-than b-values(α>b)indicate that this earthquake was governed by large events as opposed to small-magnitude events.The Harnai sequence had a decay exponent close to unity,lasted for 145 days,and produced few aftershocks.The study will help the future hazard mitigation in the region.

Co and postseismic fault slip models of the 2022 M_(W)6.7 Menyuan earthquake reveal conjugated faulting tectonics at the central section of the Lenglongling fault

The 2022 M_(W)6.7 Menyuan earthquake ruptured the western end of the Tianzhu seismic gap,providing an opportunity to study the regional seismogenic characteristics and seismic hazards.Here we use interferometric synthetic aperture radar(InSAR)and seismic data to study the mainshock rupture,early afterslip and the second largest aftershock of the 2022 Menyuan earthquake sequences.Our modeling results show that the mainshock ruptured the Lenglongling fault and the Tuolaishan fault with a maximum slip of~3 m.Rapid postseismic transient deformation occurred at the center of the Lenglongling fault.Our afterslip modeling reveals that the majority of afterslip occurred in the deeper part of the Lenglongling fault.A high-angle conjugated faulting event is found at the middle section of the Lenglongling fault.We use the stress inversion to investigate the possible triggering mechanism of the conjugated rupture event.The results indicate the maximum principal stress direction is in~222°,forming a~22°angle between the conjugated fault of second largest aftershock and the mainshock.The calculated normal stress changes indicate the region is within a pull-apart stress field,which favors such a conjugated rupturing event.Our study will help understand the rupture behavior of such kind of conjugated fault in other regions.

Interseismic slip distribution and locking characteristics of the mid-southern segment of the Tanlu fault zone

We employ the block negative dislocation model to invert the distribution of fault coupling and slip rate deficit on the different segments of the Tanlu(Tancheng-Lujiang) fault zone, according to the GPS horizontal velocity field from 1991 to 2007(the first phase) and 2013 to 2018(the second phase). By comparing the deformation characteristics results, we discuss the relationship between the deformation characteristics with the M earthquake in Japan. The results showed that the fault coupling rate of the northern section of Tancheng in the second phase reduced compared with that in the first phase. However, the results of the two phases showed that the northern section of Juxian still has a high coupling rate, a deep blocking depth, and a dextral compressive deficit, which is the enrapture section of the 1668 Tancheng earthquake. At the same time, the area strain results show that the strain rate of the central and eastern regions of the second phase is obviously enhanced compared with that of the first phase. The occurrence of the great earthquake in Japan has played a specific role in alleviating the strain accumulation in the middle and south sections of the Tanlu fault zone. The results of the maximum shear strain show that the shear strain in the middle section of the Tanlu fault zone in the second phase is weaker than that in the first phase, and the maximum shear strain in the southern section is stronger than that in the first phase. The fault coupling coefficient of the south Sihong to Jiashan section is high, and it is also the unruptured section of historical earthquakes. At the same time, small earthquakes in this area are not active and accumulate stress easily, so the future earthquake risk deserves attention.

Risk factors and clinical significance of posterior slip of the proximal vertebral body after lower lumbar fusion

BACKGROUND Adjacent segment disease(ASD)after fusion surgery is frequently manifests as a cranial segment instability,disc herniation,spinal canal stenosis,spondylolisthesis or retrolisthesis.The risk factors and mechanisms of ASD have been widely discussed but never clearly defined.AIM To investigate the risk factors and clinical significance of retrograde movement of the proximal vertebral body after lower lumbar fusion.METHODS This was a retrospective analysis of the clinical data of patients who underwent transforaminal lumbar interbody fusion surgery between September 2015 and July 2021 and who were followed up for more than 2 years.Ninety-one patients with degenerative lumbar diseases were included(22 males and 69 females),with an average age of 52.3 years(40-73 years).According to whether there was retrograde movement of the adjacent vertebral body on postoperative X-rays,the patients were divided into retrograde and nonretrograde groups.The sagittal parameters of the spine and pelvis were evaluated before surgery,after surgery,and at the final follow-up.At the same time,the Oswestry Disability Index(ODI)and Visual Analogue Scale(VAS)were used to evaluate the patients’quality of life.RESULTS Nineteen patients(20.9%)who experienced retrograde movement of proximal adjacent segments were included in this study.The pelvic incidence(PI)of the patients in the retrograde group were significantly higher than those of the patients in the nonretrograde group before surgery,after surgery and at the final follow-up(P<0.05).There was no significant difference in lumbar lordosis(LL)between the two groups before the operation,but LL in the retrograde group was significantly greater than that in the nonretrograde group postoperatively and at the final follow-up.No significant differences were detected in terms of the|PI–LL|,and there was no significant difference in the preoperative lordosis distribution index(LDI)between the two groups.The LDIs of the retrograde group were 68.1%±11.5%and 67.2%±11.9%,respectively,which were significantly lower than those of the nonretrograde group(75.7%±10.4%and 74.3%±9.4%,respectively)(P<0.05).Moreover,the patients in the retrograde group had a greater incidence of a LDI<50%than those in the nonretrograde group(P<0.05).There were no significant differences in the ODI or VAS scores between the two groups before the operation,but the ODI and VAS scores in the retrograde group were significantly worse than those in the nonretrograde group after the operation and at the last follow-up,(P<0.05).CONCLUSION The incidence of posterior slippage after lower lumbar fusion was approximately 20.9%.The risk factors are related to a higher PI and distribution of lumbar lordosis.When a patient has a high PI and insufficient reconstruction of the lower lumbar spine,adjacent segment compensation via posterior vertebral body slippage is one of the factors that significantly affects surgical outcomes.