STUDY ON MAXIMUM SPECIFIC SLUDGE ACTIVITY OF DIFFERENT ANAEROBIC GRANULAR SLUDGE BY BATCH TESTS

The maximum specific sludge activity of granular sludge from large scale UASB, IC and Biobed anaerobic reactors were investigated by batch tests. The limitation factors related to maximum specific sludge activity (diffusion, substrate sort, substrate concentration and granular size) were studied. The general principle and procedure for the precise measurement of maximum specific sludge activity were suggested. The potential capacity of loading rate of the IC and Biobed anaerobic reactors were analyzed and compared by use of the batch tests results.

Synergetic Bioproduction of Short-Chain Fatty Acids from Waste Activated Sludge Intensified by the Combined Use of Potassium Ferrate and Biosurfactants

The synergetic effect and underlying mechanism of potassium ferrate(PF)with tea saponin(TS,a biosurfactant)in producing short chain fatty acids(SCFAs)from anaerobic fermentation of waste activated sludge(WAS)were explored in this work.Experimental results showed that 0.2 g PF(g TSS)^(-1)(total suspended solid)combined with 0.02 g TS(g TSS)^(-1) could further improve SCFAs’production,and the maximum SCFAs content reached 2008.7 mg COD L^(-1),which is 1.2 and 4.5 times higher than those with PF and TS individually added,respectively,and 5.3 times higher than that of blank WAS on Day 12.In the model substrates experiments,the degradation rates of bovine serum albumin and dextran with combination of PF and TS were 41.3%±0.1% and 48.5%±0.06%,respectively,on Day 3,which are lower than those in blank WAS(with degradation rates of 72.3%±0.5%and 90.3%±0.3%).It was revealed that the oxidative effect of PF and the solubilization of TS caused more organic matters to be dissolved out from WAS,providing a large number of biodegradable substances for subsequent SCFAs production.While WAS pretreated with the combination of PF and TS,the relative abundances of Firmicutes increased from 6.4%(blank)to 38.6%,and that of Proteobacteria decreased from 41.8%(blank)to 21.8%.The combination of PF and TS promoted the hydrolysis process of WAS by enriching Firmicutes,and then increased acetic acid production by inhibiting Proteobacteria that consumed SCFAs.Meanwhile,at the genus level,acidogenesis bacteria(e.g.,Proteiniclasticum and Petrimonas)were enriched whereas SCFAs consuming bacteria(e.g.,Dokdonella)were inhibited.

Effect of high-strength ammonia nitrogen acclimation on sludge activity in sequencing batch reactor

The effect of high-strength ammonia nitrogen acclimation on sludge activity in sequencing batch reactor （SBR） was investigated. Two batch experiments, RUN1 and RUN2, were conducted with the influent ammonia nitrogen concentrations 60 and 500 mg/L, respectively. The sludges inoculated from RUN1 and RUN2 were used to treat a series of influent with ammonia nitrogen concentrations of 59, 232, 368, 604 and 1152 mg/L. It is found that the activated sludge acclimated to higher ammonia nitrogen concentrations revealed higher COD and NH 4 ＋ -N removal efficiencies, and slower DHA decrease. The results confirmed that the activities of the bacteria in activated sludge in SBR were inhibited by high-strength ammonia nitrogen, whereas the activated sludge acclimated to high-strength ammonia nitrogen showed substantial resistance to inhibition by influents containing high levels of ammonia nitrogen.

Optimization of detecting hydrogenase activity for acidogenic fermentation of activated sludge

In order to evaluate the hydrogen-producing efficiency of anaerobic activated sludge in Anaerobic Baffled Reactor(ABR)fermentation processes,the optimal conditions for hydrogen producing hydrogenase method on methyl viologen(MV)assay was used to detect the hydrogen production activity of the activated sludge.The most favorable parameters such as 0.6 mL sodium acetate buffer(pH 5.0),100 μL lysozyme,0.2 mL sodium dibromoethane(9.0 mmol/L)and 0.7 mmol/L iron added into 1 mL activated sludge(2.66～26.64 gMLVSS/L)were found.Furthermore,reaction temperature and culture time were detected as 40 ℃ and 30 min respectively.Sodium thiosulfate and sodium sulfides were taken as the reducing agent while trichloroacetic acid as terminator.Under the MV optimal conditions,micro-toxic Dimethyl sulfoxide(DMSO)get higher security and better accuracy.The sensitivity of the detection methods(DMSO as electron carrier)was increased by more than 30%.The results show that the optimal conditions can be applied to measure hydrogenase activity correlating with its specific hydrogen production rate in a hydrogen-producing anaerobic activated sludge system.

Use of Tetrazolium Salt INT for Estimation of Biological Activity of Activated Sludge Cultivated in SBR Process

The tetrazolium salt 2-( 4-Iodophenyl)-3-( 4-nitrophenyl)-5-phenyltetrazolium chloride( INT) was used as a tool for estimating the activity of the electron transport system( ETS) in activated sludge in a 40 L sequencing batch reactor( SBR) and domestic sewage as the organic substrate. The activity of INT-ETS during one SBR cycle,and the effect of the ammonia concentration and the concentration of organic matter influent on the INT-ETS activity were investigated. The results show that: the use of INT is reliable in estimating of biological activity of activated sludge of SBR system; Biological activity of organic matter biodegradation, nitrification and denitrification process in SBR system reduce orderly. Obviously,INT-ETS activity reduces from 232. 59 mg /( g·h) to 190. 65 mg /( g·h) at first and then decreases to 113. 88 mg /( g·h) when influent concentration of COD and NH4 +-N is 300 mg / L and 40 mg / L respectively. In addition,various influent Nitrogen( NH4 +-N are 14. 5 mg / L and 42. 0 mg / L) and organic shock loading( COD are 293 mg / L and 685 mg / L) experimentations cure prove that operational conditions have no obvious effect on INT-ETS variation rule. However,the time of the appearance of feature points marking different reaction phase is influenced.

Effects of Tourmaline on Dehydrogenase Activity of Activated Sludge

The black tourmaline produced in Lingshou of Hebei Province was characterized by X-ray diffraction and scanning electron microscope,and the effect of tourmaline on dehydrogenase activity of activated sludge was studied.The results showed that tourmaline increased the dehydrogenase activity of activated sludge and enhanced the stability of dehydrogenase to pH change.It made the pH value of activated sludge with different initial pH value tend to about 7.4,and improved the dehydrogenase activity of activated sludge.In addition to affecting water molecular groups,it was also related to maintaining the constant weak alkaline pH of the system.

Effects of Potassium Ferrate and Low-Temperature Thermal Hydrolysis Co-Pretreatment on the Hydrolysis and Anaerobic Digestion Process of Waste Activated Sludge

This study evaluated the effect of potassium ferrate(PF)and low-temperature thermal hydrolysis co-pretreatment on the promotion of sludge hydrolysis process and the impact on acid production in the subsequent anaerobic digestion process.The analytical investigations showed that co-pretreatment significantly facilitated the hydrolysis process of the sludge and contributed to the accumulation of short-chain fatty acids(SCFAs).The pretreatment conditions under the optimal leaching of organic matter from sludge were hydrothermal temperature of 75℃,hydrothermal treatment time of 12 h,and PF dosage of 0.25 g g^(−1)TSS(total suspended solids),according to the results of orthogonal experiments.By pretreatment under proper conditions,the removal rate of soluble chemical oxygen demand(SCOD)achieved 71.8%at the end of fermentation and the removal rate of total phosphorus(TP)was 69.1%.The maximum yield of SCFAs was 750.3 mg L^(−1),7.45 times greater than that of the blank group.Based on the analysis of the anaerobic digestion mechanism,it was indicated that the co-pretreatment could destroy the floc structure on the sludge surface and improve organic matter dissolving,resulting in more soluble organic substances for the acidification process.Furthermore,microbial community research revealed that the main cause of enhanced SCFAs generation was an increase in acidogenic bacteria and a reduction of methanogenic bacteria.

Preliminary Study on the Treatment Efficiency of Pasteurized Lime Thermal Alkaline Hydrolysis for Excess Activated Sludge and Reduction of Tetracycline Resistance Genes

Thermal alkaline hydrolysis is a common pretreatment method for the utilization of excess activated sludge(EAS).Owing to strict environment laws and need for better energy utilization,new methods were developed in this study to improve the efficiency of pretreatment method.Direct thermal hydrolysis(TH),pasteurized thermal hydrolysis(PTH),and alkaline pasteurized thermal hydrolysis(PTH+CaO and PTH+NaOH)methods were used to treat EAS.Each method was compared and analyzed in terms of dissolution in ammonium nitrogen(NH_(4)^(+)-N)and soluble COD(SCOD)in EAS.Furthermore,the removal of tetracycline resistance genes(TRGs)and class 1 transposon gene intI1 from EAS was investigated.The NH_(4)^(+)-N and SCOD concentrations in EAS treated by PTH were 1.24 and 2.58 times higher than those of TH.However,the removal efficiency of total TRGs and intI1 between the groups was comparable.The SCOD concentration of the PTH+NaOH group was 4.37 times higher than that of the PTH group,and the removal efficiency of total TRGs was increased by 9.52%compared with that by PTH.The NH_(4)^(+)-N and SCOD concentrations of the PTH+CaO group could reach 85.04%and 92.14%of the PTH+NaOH group,but the removal efficiency of total TRGs by PTH+CaO was 19.78%lower than that by PTH+NaOH.Thus,to reduce the financial cost in actual operation,lime(CaO)can be used instead of a strong alkali(NaOH),and pasteurized steam at 70℃ instead of conventional high-temperature heating to treat EAS.This study provides a reference for the development of alkaline hydrolysis under moderate temperatures along with the removal of TRGs in EAS.

Analysis of bacterial community structures in two sewage treatment plants with different sludge properties and treatment performance by nested PCR-DGGE method

The bacterial community structures in two sewage treatment plants with different processes and performance were investigated by denaturing gradient gel electrophoresis （DGGE） of nested polymerase chain reaction （nested PCR） amplified 16S rRNA gene fragments with group-specific primers. Samples of raw sewage and treated effluents were amplified using the whole-cell PCR method, and the activated sludge samples were amplified using the extracted genomic DNA before the PCR products were loaded on the same DGGE gel for bacterial community analysis. Ammonia-oxidizing bacterial and actinomycetic community analysis were also carried out to investigate the relationship between specific population structures and system or sludge performance. The two plants demonstrated a similarity in bacterial community structures of raw sewage and activated sludge, but they had different effluent populations. Many dominant bacterial populations of raw sewage did not appear in the activated sludge samples, suggesting that the dominant bacterial populations in raw sewage might not play an important role during wastewater treatment. Although the two plants had different sludge properties in terms of settleability and foam forming ability, they demonstrated similar actinomycetic community structures. For activated sludge with bad settling performance, the treated water presented a similar DGGE pattern with that of activated sludge, indicating the nonselective washout of bacteria from the system. The plant with better ammonium removal efficiency showed higher ammonia-oxidizing bacteria species richness. Analysis of sequencing results showed that the major populations in raw sewage were uncultured bacterium, while in activated sludge the predominant populations were beta proteobacteria.

Combined alkaline and ultrasonic pretreatment of sludge before aerobic digestion

Alkaline and ultrasonic sludge disintegration can be used as the pretreatment of waste activated sludge （WAS） to promote the subsequent anaerobic or aerobic digestion. In this study, different combinations of these two methods were investigated. The evaluation was based on the quantity of soluble chemical oxygen demand （SCOD） in the pretreated sludge as well as the degradation of organic matter in the subsequent aerobic digestion. For WAS samples with combined pretreatment, the released COD levels were higher than those with ultrasonic or alkaline pretreatment alone. When combined with the ultrasonic treatment, NaOH treatment was more efficient than Ca（OH）2 for WAS solubilization. The COD levels released in various sequential options of combined NaOH and ultrasonic treatments were in the the following descending order： simultaneous treatment 〉 NaOH treatment followed by ultrasonic treatment 〉 ultrasonic treatment followed by NaOH treatment. For simultaneous treatment, low NaOH dosage （100 g/kg dry solid）, short duration （30 min） of NaOH treatment, and low ultrasonic specific energy （7500 kJ/kg dry solid） were suitable for sludge disintegration. Using combined NaOH and ultrasonic pretreatment with optimal parameters, the degradation efficiency of organic matter was increased from 38.0% to 50.7%, which is much higher than that with ultrasonic （42.5%） or with NaOH pretreatment （43.5%） in the subsequent aerobic digestion at the same retention time.

Functions and behaviors of activated sludge extracellular polymeric substances (EPS): a promising environmental interest

Extracellular polymeric substances （EPS） are the predominant constituents of activated sludge and represent up to 80% of the mass of activated sludge. They play a crucial role in the flocculation, settling and dewatering of activated sludge. Furthermore, EPS also show great efficiency in binding heavy metals. So EPS are key factors influencing reduction in sludge volume and mass, as well as activity and utilization of sludge. EPS are of considerable environmental interest and hundreds of articles on EPS have been published abroad, while information on EPS in China is limited. In this paper, results of over 60 publications related to constituents and characteristics of EPS and their influences on flocculation, settling and dewatering of sludge are compiled and analyzed. Metal-binding ability of EPS is also discussed, together with a brief consideration of possible research interests in the future.

Biosorption of cadmium(II) and lead(II) ions from aqueous solutions onto dried activated sludge

The removal of heavy-metal ions from aqueous solutions by using dried activated sludge has been investigated in batch systems. Effect of solution pH, initial metal ion concentration, and temperature were determined. The results of the kinetic studies showed that the uptake processes of the two metal ions（Cd（Ⅱ） and Pb（Ⅱ）） followed the pseudo-second-order rate expression. The equilibrium data fitted very well to both the Langmuir and Freundlich adsorption models. The FT-IR analysis showed that the main mechanism of Cd（Ⅱ） and Pb（Ⅱ） biosorption onto dried activated sludge was their binding with amide I group.

Start-up of anaerobic ammonia oxidation bioreactor with nitrifying activated sludge

The anaerobic ammonia oxidation(Anammox) bioreactor was successfully started up with the nitrifying activated sludge. After anaerobically operated for 105 d, the bioreactor reached a good performance with removal percentage of both ammonia and nitrite higher than 95% and volumetric total nitrogen removal as high as 149.55 mmol/(L·d). The soft padding made an important contribution to the high efficiency and stability because it held a large amount of biomass in the bioreactor.

Immobilization study of biosorption of heavy metal ions onto activated sludge

Activated sludge was immobilized into Ca-alginate beads via entrapment, and biosorption of three heavy metal ions, copper(Ⅱ), zinc(Ⅱ), and chromimum(Ⅱ), from aqueous solution in the concentration range of 10\_100 mg/L was studied by using both entrapped activated sludge and inactivated free biomass at pH≤5. A biphasic metal adsorption pattern was observed in all immobilized biomass experiments. The biosorption of metal ions by the biosorbents increased with the initial concentration increased in the medium. The adsorption rate of immobilized pre-treated activated sludge(PAS) was much lower than that of free PAS due to the increase in mass transfer resistance resulting from the polymeric matrix. Biosorption equilibrium of beads was established in about 20 h and the adsorbed heavy metal ions did not change further with time. No significant effect of temperature was observed in the test for free biomass while immobilized PAS appeared to be strong temperature dependent in the test range of 10 and 40℃. Besides, the content of activated sludge in the calcium alginate bead has an influence on the uptake of heavy metals. The sorption equilibrium was well modeled by Langmuir isotherm, implying monomolecular adsorption mechanism. Carboxyl group in cell wall played an important role in surface adsorption of heavy metal ions on PAS.

Community analysis of ammonia-oxidizing bacteria in activated sludge of eight wastewater treatment systems

We investigated the communities of ammonia-oxidizing bacteria （AOB） in activated sludge collected from eight wastewater treatment systems using polymerase chain reaction （PCR） followed by terminal restriction fragment length polymorphism （T-RFLP）, cloning, and sequencing of the α-subunit of the ammonia monooxygenase gene （amoA）. The T-RFLP fingerprint analyses showed that different wastewater treatment systems harbored distinct AOB communities. However, there was no remarkable difference among the AOB T- RFLP profiles from different parts of the same system. The T-RFLP fingerprints showed that a full-scale wastewater treatment plant （WWTP） contained a larger number of dominant AOB species than a pilot-scale reactor. The source of influent affected the AOB community, and the WWTPs treating domestic wastewater contained a higher AOB diversity than those receiving mixed domestic and industrial wastewater. However, the AOB community structure was little affected by the treatment process in this study. Phylogenetic analysis of the cloned amoA genes clearly indicated that all the dominant AOB in the systems was closely related to Nitrosomonas spp. not to Nitrosospira spp. Members of the Nitrosomonas oligotropha and Nitrosomonas communis clusters were found in all samples, while members of Nitrosomonas europaea cluster occurred in some systems.

Kinetic analysis of waste activated sludge hydrolysis and short-chain fatty acids production at pH 10

The accumulation of short-chain fatty acids （SCFAs）, a preferred carbon source for enhanced biological phosphorus removal microbes, was significantly improved when waste activated sludge （WAS） was fermented at pH 10. The kinetics of WAS hydrolysis and SCFAs production at pH 10 was investigated. It was observed that during WAS anaerobic fermentation the accumulation of SCFAs was limited by the hydrolysis process, and both the hydrolysis of WAS particulate COD and the accumulation of SCFAs followed first-order kinetics. The hydrolysis and SCFAs accumulation rate constants increased with increasing temperature from 10 to 35℃, which could be described by the Arrhenius equation. The kinetic data further indicated that SCFAs production at pH 10 was a biological process. Compared with the experiment of pH uncontrolled （blank test）, both the rate constants of WAS hydrolysis and SCFAs accumulation at 20℃ were improved significantly when WAS was fermented at pH 10.

Purification of total DNA extracted from activated sludge

Purification of the total DNA extracted from activated sludge samples was studied. The effects of extraction buffers and lysis treatments （lysozyme, sodium dodecyl sulfate （SDS）, sonication, mechanical mill and thermal shock） on yield and purity of the total DNA extracted from activated sludge were investigated. It was found that SDS and mechanical mill were the most effective ways for cell lysis, and both gave the highest DNA yields, while by SDS and thermal shock, the purest DNA extract could be obtained. The combination of SDS with other lysis treatment, such as sonication and thermal shock, could apparently increase the DNA yields but also result in severe shearing. For the purification of the crude DNA extract, polyvinyl polypyrrolidone was used for the removal of humic contaminants. Cetyltrimethyl ammonium bromide, potassium acetate and phenol/chloroform were used to remove proteins and polysaccharides from crude DNA. Crude DNA was further purified by isopropanol precipitation. Thus, a suitable protocol was proposed for DNA extraction, yielding about 49.9 mg （total DNA）/g volatile suspended solids, and the DNA extracts were successfully used in PCR amplifications for 16S rDNA and 16S rDNA V3 region. The PCR products of 16S rDNA V3 region allowed the DGGE analysis （denatured gradient gel electrophoresis） to be possible.

Optimization of process parameters for the bioconversion of activated sludge by Penicillium corylophilum, using response surface methodology

The optimization of process parameters for the bioconversion of activated sludge by Penicillium corylophilum was investigated using response surface methodology （RSM）. The three parameters namely temperature of 33℃, agitation of 150 r/min, and pH of 5 were chosen as center point from the previous study of fungal treatment. The experimental data on chemical oxygen demand （COD） removal （%） were fitted into a quadratic polynomial model using multiple regression analysis. The optimum process conditions were determined by analyzing response surface three-dimensional surface plot and contour plot and by solving the regression model equation with Design Expert software. Box-Behnken design technique under RSM was used to optimize their interactions, which showed that an incubation temperature of 32.5℃, agitation of 105 r/min, and pH of 5.5 were the best conditions. Under these conditions, the maximum predicted yield of COD removal was 98.43%. These optimum conditions were used to evaluate the trail experiment, and the maximum yield of COD removal was recorded as 98.5%.

Biosorption of zinc(Ⅱ) from aqueous solution by dried activated sludge

The biosorption potential of dried activated sludge as a biosorbent for zinc（Ⅱ） removal from aqueous solution was investigated.The effects of initial pH,contact time,initial zinc ion concentration,and adsorbent dosage on the biosorption processes were determined,and the equilibrium data were modeled by the Langmuir and Freundlich isotherms.The Langmuir isotherm model （R 2=0.999） was proved to fit the equilibrium data much better than the Freundlich isotherm model （R 2=0.918）.The monolayer adsorption capacity of dried activated sludge for zinc（Ⅱ） was found to be 17.86 mg/g at pH of 5 and 25°C.The kinetic data were tested using pseudo firstand second-order models.The results suggested that the pseudo second-order model （R 2 〉 0.999） was better for the description of the adsorption behavior of zinc（Ⅱ） onto the dried activated sludge.Fourier transform infrared spectral analysis showed that the dominant mechanism of zinc（Ⅱ） biosorption onto the dried activated sludge was the binding between amide groups and zinc ions.

Effect of Salinity Variations on the Performance of Activated Sludge System

To investigate the influence of salinity variations on the performance of activated sludge systems, treating domestic wastewater. Methods The completely mixed reactor was used and operated in a batch-wise mode. The activated sludge taken from the Gaobeidian Wastewater Treatment Plant was used as a seeding sludge. Total organic carbon (TOC), oxygen uptake rate (OUR) and suspended solids (SS) were used as parameters to characterize the performance of the treatment systems. TOC was measured using a TOC-analyzer (TOC-5000, Japan). The OUR value was measured with a dissolved oxygen meter (YSI model-58). SS was measured gravimetrically. Results The TOC removal efficiency and the OUR value of activated sludge were not deteriorated when the NaCl shock concentration was less than 0.5 g/L. However, when the NaCl shock concentrations were up to 10g/L and 20 g/L, the OUR of activated sludge was reduced by 35% and TOC removal efficiency was dropped by 30%, compared with the control experiment without NaCl shock loading. Conclusion The effect of NaCl shock loading on the activated sludge wastewater treatment system is dependant upon the NaCl concentrations and the degree of influence can be inferred through the change of substrate utilization rate at different shock NaCl loadings.