Concentrations of polychlorinated biphenyls （PCBs） have been measured in sewage sludge samples from 8 urban wastewater treatment plants in Beijing, China. The PCB congeners were analyzed by isotope dilution high res...Concentrations of polychlorinated biphenyls （PCBs） have been measured in sewage sludge samples from 8 urban wastewater treatment plants in Beijing, China. The PCB congeners were analyzed by isotope dilution high resolution gas chromatography/high resolution mass spectrometry method. The concentration of PCBs ranged from 65.6 to 157 ng/g dry weight （dw）, with a mean value of 101 ng/g dw. The dioxin-like PCB WHO-TEQs （World Health Organization-Toxic Equivalents） of the sludge were lower than 1 pg /g dw. Consequently, all the concentrations of PCBs in sludge samples were below the upper limit for land application according to the Chinese legislation law for agriculture use. The PCB homologue profiles in sludge samples were dominated by tri-CBs and tetra- CBs. Similar distributions have been found in one of the Chinese PCB commercial products. The patterns of dioxin-like and indicator congeners observed in this study were quite similar in all samples. The predominant congener for dioxin-like and indicator PCBs were PCB-118 and PCB-28, respectively, while PCB-126 had the highest TEQ value.展开更多
UNITANK is a biological wastewater treatment process that combines the advantages of traditional activated sludge process and sequencing batch reactor, which is divided into Tank A, B and C. In this study, the sludge ...UNITANK is a biological wastewater treatment process that combines the advantages of traditional activated sludge process and sequencing batch reactor, which is divided into Tank A, B and C. In this study, the sludge distribution and its impact on performance of UNITANK were carried out in Liede Wastewater Plant （WWTP） of Guangzhou, China. Results showed that there was a strong affiliation between Tank A and B of the system in sludge concentration distribution. The initial sludge concentration in Tank A could present the sludge distribution of the whole system. The sludge distribution was mainly influenced by hydraulic condition. Unsteady sludge distribution had an impact on variations of substrates in reactors, especially in decisive reactor, and this could lead to failure of system. Settler could partially remove substrates such as COD and NO3-N, but there was adventure of sludge deterioration. The rational initial sludge concentration in Tank A should be 4000-6000 mg/L MLSS.展开更多
The modified three-step sequential extraction procedure proposed by the BCR was used to predict Pb and Cd fractional distribution in sewage sludge and tomato soil amended with sludge compost. There was no significant ...The modified three-step sequential extraction procedure proposed by the BCR was used to predict Pb and Cd fractional distribution in sewage sludge and tomato soil amended with sludge compost. There was no significant increasing of Pb and Cd contents in the soil with sludge application as compared with that in the reference soil. The Pb contents were much lower for the soil samples than for the National Soil Standards of Environmental Quality, but Cd contents in soil were much more than background mean Cd contents. Pb content in soil fractions was followed with residual Pb 〉 reducible Pb 〉 exchangeable and weak acid soluble Pb〉 oxidizable Pb. In all soil samples, the partitioning of Cd had the same extractability in the first two steps of the procedure and the residual fraction. Only a small fraction or almost zero extractability was observed at the oxidation step for Pb and Cd.展开更多
The laboratory scale experiments for determining the influence on the distribution of phosphorus by.adding Al-containing component in melting furnace were conducted. It is found that the addition of Al-containing comp...The laboratory scale experiments for determining the influence on the distribution of phosphorus by.adding Al-containing component in melting furnace were conducted. It is found that the addition of Al-containing component in melting furnace increased the amount of phosphorus in slag phase. Thermodynamic analysis of the industrial sludge melting process with the addition of different Al-containing components was also carried out. The compositions of slag and the gas in three different zones in melting furnace were obtained. The results also demonstrate that increasing the mole ratio Al/P of charged materials is an effective way to fix more phosphorus in slap, which can help reduce the amount of H3PO4 precipitate from guy in the waste heat boiler later.展开更多
The potential toxicity risks from heavy metals depend on their chemical speciation. The four stages of the Tessier sequential extraction method were employed to investigate changes in heavy metal speciation （Cu, Zn, ...The potential toxicity risks from heavy metals depend on their chemical speciation. The four stages of the Tessier sequential extraction method were employed to investigate changes in heavy metal speciation （Cu, Zn, and Cd） of sewage sludge during forced aeration composting, and then to identify whether the composting process would reduce or enhance their toxicities. Throughout the composting process, the exchangeable, carbonate-bound, Fe-Mn oxide-bound, and organic matter-bound fractions of Cu were converted to the residual Cu fraction. The organic matter-bound Cu fraction greatly contributed to this transformation. Residual Zn fraction was transformed to the Fe-Mn oxide-bound and organic matter-bound fractions after composting. The residual Zn fraction was a major contributor to the organic matter-bound Zn fraction. The availability of Cu and Zn was reduced by composting such that the risk of heavy metal toxicity decreased with prolonged treatment times. Additionally, attention should be paid to the increased availability of Cd in sewage sludge after composting treatment.展开更多
A pilot-scale modified carbon source division anaerobic anoxic oxic(AAO) process with pre-concentration of returned activated sludge(RAS) was proposed in this study for the enhanced biological nutrient removal(BNR) of...A pilot-scale modified carbon source division anaerobic anoxic oxic(AAO) process with pre-concentration of returned activated sludge(RAS) was proposed in this study for the enhanced biological nutrient removal(BNR) of municipal wastewater with limited carbon source. The influent carbon source was fed in step while a novel RAS pre-concentration tank was adopted to improve BNR efficiency, and the effects of an influent carbon source distribution ratio and a RAS pre-concentration ratio were investigated. The results show that the removal efficiency of TN is mainly influenced by the carbon source distribution ratio while the TP removal relies on the RAS pre-concentration ratio. The optimum carbon source distribution ratio and RAS pre-concentration ratio are 60% and 50%, respectively, with an inner recycling ratio of 100% under the optimum steady operation of pilot test, reaching an average effluent TN concentration of 9.8 mg·L-1with a removal efficiency of 63% and an average TP removal efficiency of 94%. The mechanism of nutrient removal is discussed and the kinetics is analyzed. The results reveal that the optimal carbon source distribution ratio provides sufficient denitrifying carbon source to each anoxic phase, reducing nitrate accumulation while the RAS pre-concentration ratio improves the condition of anaerobic zone to ensure the phosphorus release due to less nitrate in the returned sludge. Therefore, nitrifying bacteria, denitrifying bacteria and phosphorus accumulation organisms play an important role under the optimum condition, enhancing the performance of nutrient removal in this test.展开更多
Moisture distributions in municipal sewage sludge, printing and dyeing sludge and paper mill sludge were experimentally studied based on four different methods, i.e., drying test, thermogravimetric-differential therma...Moisture distributions in municipal sewage sludge, printing and dyeing sludge and paper mill sludge were experimentally studied based on four different methods, i.e., drying test, thermogravimetric-differential thermal analysis （TG-DTA） test, thermogravimetric- differential scanning calorimetry （TG-DSC） test and water activity test. The results indicated that the moistures in the mechanically dewatered sludges were interstitial water, surface water and bound water. The interstitial water accounted for more than 50% wet basis （wb） of the total moisture content. The bond strength of sludge moisture increased with decreasing moisture content, especially when the moisture content was lower than 50% wb. Furthermore, the comparison among the four different testing methods was presented. The drying test was advantaged by its ability to quantify free water, interstitial water, surface water and bound water; while TG-DSC test, TG-DTA test and water activity test were capable of determining the bond strength of moisture in sludge. It was found that the results from TG-DSC and TG-DTA test are more persuasive than water activity test.展开更多
A key step in sludge treatment is sludge dewatering. However, activated sludge is generally very difficult to be dewatered. Sludge dewatering performance is largely affected by the sludge moisture distribution. Sludge...A key step in sludge treatment is sludge dewatering. However, activated sludge is generally very difficult to be dewatered. Sludge dewatering performance is largely affected by the sludge moisture distribution. Sludge disintegration can destroy the sludge structure and cell wall, so as change the sludge floc structure and moisture distribution, thus affecting the dewatering performance of sludge. In this article, the disintegration methods were ultrasound treatment, K2 Fe O4oxidation and KMn O4 oxidation. The degree of disintegration（DDCOD）, sludge moisture distribution and the final water content of sludge cake after centrifuging were measured. Results showed that three disintegration methods were all effective, and K2 Fe O4oxidation was more efficient than KMn O4 oxidation. The content of free water increased obviously with K2 Fe O4and KMn O4 oxidations, while it decreased with ultrasound treatment. The changes of free water and interstitial water were in the opposite trend. The content of bounding water decreased with K2 Fe O4oxidation, and increased slightly with KMn O4 oxidation, while it increased obviously with ultrasound treatment. The water content of sludge cake after centrifuging decreased with K2 Fe O4oxidation, and did not changed with KMn O4 oxidation, but increased obviously with ultrasound treatment. In summary, ultrasound treatment deteriorated the sludge dewaterability, while K2 Fe O4and KMn O4 oxidation improved the sludge dewaterability.展开更多
基金supported by the Key Project of Chinese Academy of Sciences (No. KZCX2-YW-420)the National Basic Research Program (973) of China (No.2009CB421606)the National Natural Science Foundation of China (No. 20621703)
文摘Concentrations of polychlorinated biphenyls （PCBs） have been measured in sewage sludge samples from 8 urban wastewater treatment plants in Beijing, China. The PCB congeners were analyzed by isotope dilution high resolution gas chromatography/high resolution mass spectrometry method. The concentration of PCBs ranged from 65.6 to 157 ng/g dry weight （dw）, with a mean value of 101 ng/g dw. The dioxin-like PCB WHO-TEQs （World Health Organization-Toxic Equivalents） of the sludge were lower than 1 pg /g dw. Consequently, all the concentrations of PCBs in sludge samples were below the upper limit for land application according to the Chinese legislation law for agriculture use. The PCB homologue profiles in sludge samples were dominated by tri-CBs and tetra- CBs. Similar distributions have been found in one of the Chinese PCB commercial products. The patterns of dioxin-like and indicator congeners observed in this study were quite similar in all samples. The predominant congener for dioxin-like and indicator PCBs were PCB-118 and PCB-28, respectively, while PCB-126 had the highest TEQ value.
基金Project supported by the National Natural Science Foundation of China (No. 50238050).
文摘UNITANK is a biological wastewater treatment process that combines the advantages of traditional activated sludge process and sequencing batch reactor, which is divided into Tank A, B and C. In this study, the sludge distribution and its impact on performance of UNITANK were carried out in Liede Wastewater Plant （WWTP） of Guangzhou, China. Results showed that there was a strong affiliation between Tank A and B of the system in sludge concentration distribution. The initial sludge concentration in Tank A could present the sludge distribution of the whole system. The sludge distribution was mainly influenced by hydraulic condition. Unsteady sludge distribution had an impact on variations of substrates in reactors, especially in decisive reactor, and this could lead to failure of system. Settler could partially remove substrates such as COD and NO3-N, but there was adventure of sludge deterioration. The rational initial sludge concentration in Tank A should be 4000-6000 mg/L MLSS.
文摘The modified three-step sequential extraction procedure proposed by the BCR was used to predict Pb and Cd fractional distribution in sewage sludge and tomato soil amended with sludge compost. There was no significant increasing of Pb and Cd contents in the soil with sludge application as compared with that in the reference soil. The Pb contents were much lower for the soil samples than for the National Soil Standards of Environmental Quality, but Cd contents in soil were much more than background mean Cd contents. Pb content in soil fractions was followed with residual Pb 〉 reducible Pb 〉 exchangeable and weak acid soluble Pb〉 oxidizable Pb. In all soil samples, the partitioning of Cd had the same extractability in the first two steps of the procedure and the residual fraction. Only a small fraction or almost zero extractability was observed at the oxidation step for Pb and Cd.
文摘The laboratory scale experiments for determining the influence on the distribution of phosphorus by.adding Al-containing component in melting furnace were conducted. It is found that the addition of Al-containing component in melting furnace increased the amount of phosphorus in slag phase. Thermodynamic analysis of the industrial sludge melting process with the addition of different Al-containing components was also carried out. The compositions of slag and the gas in three different zones in melting furnace were obtained. The results also demonstrate that increasing the mole ratio Al/P of charged materials is an effective way to fix more phosphorus in slap, which can help reduce the amount of H3PO4 precipitate from guy in the waste heat boiler later.
文摘The potential toxicity risks from heavy metals depend on their chemical speciation. The four stages of the Tessier sequential extraction method were employed to investigate changes in heavy metal speciation （Cu, Zn, and Cd） of sewage sludge during forced aeration composting, and then to identify whether the composting process would reduce or enhance their toxicities. Throughout the composting process, the exchangeable, carbonate-bound, Fe-Mn oxide-bound, and organic matter-bound fractions of Cu were converted to the residual Cu fraction. The organic matter-bound Cu fraction greatly contributed to this transformation. Residual Zn fraction was transformed to the Fe-Mn oxide-bound and organic matter-bound fractions after composting. The residual Zn fraction was a major contributor to the organic matter-bound Zn fraction. The availability of Cu and Zn was reduced by composting such that the risk of heavy metal toxicity decreased with prolonged treatment times. Additionally, attention should be paid to the increased availability of Cd in sewage sludge after composting treatment.
基金Supported by the Major Science and Technology Program for Water Pollution Contro and Treatment-Crucial Technology Research and Engineering Sample Subject on Municipa Wastewater Treatment Process Updated to Higher Drainage Standard(2008ZX07317-02)Wuhan Water Pollution Control and the Water Environment Administer Technology and Synthetic Sample Project in Cities and Towns(2008ZX07317)
文摘A pilot-scale modified carbon source division anaerobic anoxic oxic(AAO) process with pre-concentration of returned activated sludge(RAS) was proposed in this study for the enhanced biological nutrient removal(BNR) of municipal wastewater with limited carbon source. The influent carbon source was fed in step while a novel RAS pre-concentration tank was adopted to improve BNR efficiency, and the effects of an influent carbon source distribution ratio and a RAS pre-concentration ratio were investigated. The results show that the removal efficiency of TN is mainly influenced by the carbon source distribution ratio while the TP removal relies on the RAS pre-concentration ratio. The optimum carbon source distribution ratio and RAS pre-concentration ratio are 60% and 50%, respectively, with an inner recycling ratio of 100% under the optimum steady operation of pilot test, reaching an average effluent TN concentration of 9.8 mg·L-1with a removal efficiency of 63% and an average TP removal efficiency of 94%. The mechanism of nutrient removal is discussed and the kinetics is analyzed. The results reveal that the optimal carbon source distribution ratio provides sufficient denitrifying carbon source to each anoxic phase, reducing nitrate accumulation while the RAS pre-concentration ratio improves the condition of anaerobic zone to ensure the phosphorus release due to less nitrate in the returned sludge. Therefore, nitrifying bacteria, denitrifying bacteria and phosphorus accumulation organisms play an important role under the optimum condition, enhancing the performance of nutrient removal in this test.
基金supported by the National Ministry of Education (China) and Technological Department of Zhejiang Province (No. 2007C03003)the Shanghai Natural Science Foundation (No. 11ZR1400700)
文摘Moisture distributions in municipal sewage sludge, printing and dyeing sludge and paper mill sludge were experimentally studied based on four different methods, i.e., drying test, thermogravimetric-differential thermal analysis （TG-DTA） test, thermogravimetric- differential scanning calorimetry （TG-DSC） test and water activity test. The results indicated that the moistures in the mechanically dewatered sludges were interstitial water, surface water and bound water. The interstitial water accounted for more than 50% wet basis （wb） of the total moisture content. The bond strength of sludge moisture increased with decreasing moisture content, especially when the moisture content was lower than 50% wb. Furthermore, the comparison among the four different testing methods was presented. The drying test was advantaged by its ability to quantify free water, interstitial water, surface water and bound water; while TG-DSC test, TG-DTA test and water activity test were capable of determining the bond strength of moisture in sludge. It was found that the results from TG-DSC and TG-DTA test are more persuasive than water activity test.
基金funded by the National Natural Science Foundation of China (No. 51278489)Key Lab for Solid Waste Management and Environmental Safety Open fund (No. 2011-8)
文摘A key step in sludge treatment is sludge dewatering. However, activated sludge is generally very difficult to be dewatered. Sludge dewatering performance is largely affected by the sludge moisture distribution. Sludge disintegration can destroy the sludge structure and cell wall, so as change the sludge floc structure and moisture distribution, thus affecting the dewatering performance of sludge. In this article, the disintegration methods were ultrasound treatment, K2 Fe O4oxidation and KMn O4 oxidation. The degree of disintegration（DDCOD）, sludge moisture distribution and the final water content of sludge cake after centrifuging were measured. Results showed that three disintegration methods were all effective, and K2 Fe O4oxidation was more efficient than KMn O4 oxidation. The content of free water increased obviously with K2 Fe O4and KMn O4 oxidations, while it decreased with ultrasound treatment. The changes of free water and interstitial water were in the opposite trend. The content of bounding water decreased with K2 Fe O4oxidation, and increased slightly with KMn O4 oxidation, while it increased obviously with ultrasound treatment. The water content of sludge cake after centrifuging decreased with K2 Fe O4oxidation, and did not changed with KMn O4 oxidation, but increased obviously with ultrasound treatment. In summary, ultrasound treatment deteriorated the sludge dewaterability, while K2 Fe O4and KMn O4 oxidation improved the sludge dewaterability.
