The measurement and assessment of dust emissions from different landforms are important to understand the atmospheric loading of PM10 (particulate matter ≤10 μm aerodynamic diameter) and to assess natural sources ...The measurement and assessment of dust emissions from different landforms are important to understand the atmospheric loading of PM10 (particulate matter ≤10 μm aerodynamic diameter) and to assess natural sources of dust; however, the methodology and technique for determining the dust still present significant research challenges. In the past, specialized field observation and field wind tunnel studies have been used to understand the dust emission. A series of wind tunnel tests were carried out to identify natural sources of dust and measure the magnitudes of dust emissions from different landforms. The method used in this study allowed the measurement of the PM10 emission rate using a laboratory based environmental boundary layer wind tunnel. Results indicated that PM10 emissions demonstrated strong temporal variation and were primarily driven by aerodynamic entrainment. Sand dunes, playa, and alluvial fans had the largest dust emission rates (0.8-5.4 mg/(me.s)) while sandy gravel, Gobi desert and abandoned lands had the lowest emission rates (0.003-0.126 mg/(m2.s)). Dust emissions were heavily dependent on the surface conditions, especially the availability of loose surface dust. High dust emissions were a result of the availability of dust- particle materials for entrainment while low dust emissions were a result of surface crusts and gravel cover. Soil surface property (surface crusts and gravel cover) plays an important role in controlling the availability of dust-sized particles for entrainment. The dust emission rate depended not only on the surface conditions but also on the friction velocity. The emission rate of PM10 varies as a power function of the friction velocity. Although dynamic abrasion processes have a strong influence on the amount of dust entrainment, aerodynamic entrainment may provide an important mechanism for dust emissions. Large volumes of dust entrained by aerodynamic entrainment cannot only occur at low shear velocity without saltation, but may dominate the entrainment process in many arid and semi-arid environments. So it may also be responsible for large magnitude dust storms. Playa and alluvial fan landforms, prior to developing a surface crust, may be the main sources of dust storms in Qinghai Province.展开更多
Tightening of air quality standards for populated urban areas has led to increasing attention to assessment of air quality management areas, where violation of air quality standards occurs, and development of control ...Tightening of air quality standards for populated urban areas has led to increasing attention to assessment of air quality management areas, where violation of air quality standards occurs, and development of control strategies to eliminate such vio-lation of air quality standards. The Quetta urban area is very densely built and has heavy motorized traffic. The increase of emis-sions mainly from traffic and industry are responsible for the increase in atmospheric pollution levels during the last years. The dust examined in the current study was collected by both deposit gauge and Petri dish methods at various sites of Quetta Valley. Smoke particles were obtained by bladder method from the exhausts of various types of motor vehicles. The concentration of lead found in the smoke ranged from 1.5×10?6 to 4.5×10?6.展开更多
This study evaluates the vertical profiles of aerosol and cloud optical properties in 40 dominated dust and smoke regions in Western-Northern Africa (WNA) and Central-Southern Africa (CSA), respectively, from the surf...This study evaluates the vertical profiles of aerosol and cloud optical properties in 40 dominated dust and smoke regions in Western-Northern Africa (WNA) and Central-Southern Africa (CSA), respectively, from the surface to 10km and from 2008 to 2011 based on LIVAS (LIdar climatology of Vertical Aerosol Structure for space-based lidar simulation studies). Aerosol extinction (AE), aerosol backscatter (AB), and aerosol depolarization (AD) generally increase from the surface to 1.2 km and decrease from 1.2 km to the upper layers in both WNA and CSA. AE and AB in CSA (maximum of 0.13 km<sup>-1</sup>, 0.14 km<sup>-1</sup>, 0.0021 km<sup>-1</sup>‧sr<sup>-1</sup>, 0.0033 km<sup>-1</sup>‧sr<sup>-1</sup>) are higher than in WNA (maximum of 0.07 km<sup>-1</sup>, 0.08 km<sup>-1</sup>, 0.0017 km<sup>-1</sup>‧sr<sup>-1</sup>, 0.0015 km<sup>-1</sup>‧sr<sup>-1</sup>) at 532 and 1064 nm respectively. AD in WNA (maximum of 0.25) is significantly higher than in CSA (maximum of 0.05). There is a smooth change with the height of cloud extinction and backscatter in WNA and CSA, while there is a remarkable increase of cloud depolarization with height, whereby it is high in CSA and low in WNA due to high and low fraction of cirrus respectively. Altocumulus has the highest extinction in NA (0.0139 km<sup>-1</sup>), CA (0.058 km<sup>-1</sup>), WA (0.013 km<sup>-1</sup>), while low overcast transparent (0.76 km<sup>-1</sup>) below 1 km in SA. The major findings of this study may contribute to the improvement of our understanding of aerosol-cloud interaction studies in dominated dust and smoke aerosol regions.展开更多
With the rapid industrialization and urbanization,the demand for air quality management is more and more urgent.High temperature dust filtration is one important environmental management technology.Porous ceramics are...With the rapid industrialization and urbanization,the demand for air quality management is more and more urgent.High temperature dust filtration is one important environmental management technology.Porous ceramics are used as filter materials in the field of high-temperature dust filtration because of their unique advantages such as high filtration efficiency,as well as high temperature stability,particle loss resistance,corrosion resistance and durability.This paper mainly introduced several common preparation techniques of porous ceramics,including the traditional organic foam impregnation method,foaming method,in-situ combustion method,pore-forming method and other new methods such as the template method,gel injection molding method,freeze-drying method,multi-component co-precipitation method and hydrogel method.The principle,advantages and disadvantages of these preparation technologies and their research status were described.The application of these technologies in the field of high temperature dust filtration was briefly reviewed.Finally,the application prospect of the porous ceramics in the field of high temperature dust filtration was prospected.展开更多
基金supported by the National Basic Research Program of China (2016YFA0601901, 2013CB956001)
文摘The measurement and assessment of dust emissions from different landforms are important to understand the atmospheric loading of PM10 (particulate matter ≤10 μm aerodynamic diameter) and to assess natural sources of dust; however, the methodology and technique for determining the dust still present significant research challenges. In the past, specialized field observation and field wind tunnel studies have been used to understand the dust emission. A series of wind tunnel tests were carried out to identify natural sources of dust and measure the magnitudes of dust emissions from different landforms. The method used in this study allowed the measurement of the PM10 emission rate using a laboratory based environmental boundary layer wind tunnel. Results indicated that PM10 emissions demonstrated strong temporal variation and were primarily driven by aerodynamic entrainment. Sand dunes, playa, and alluvial fans had the largest dust emission rates (0.8-5.4 mg/(me.s)) while sandy gravel, Gobi desert and abandoned lands had the lowest emission rates (0.003-0.126 mg/(m2.s)). Dust emissions were heavily dependent on the surface conditions, especially the availability of loose surface dust. High dust emissions were a result of the availability of dust- particle materials for entrainment while low dust emissions were a result of surface crusts and gravel cover. Soil surface property (surface crusts and gravel cover) plays an important role in controlling the availability of dust-sized particles for entrainment. The dust emission rate depended not only on the surface conditions but also on the friction velocity. The emission rate of PM10 varies as a power function of the friction velocity. Although dynamic abrasion processes have a strong influence on the amount of dust entrainment, aerodynamic entrainment may provide an important mechanism for dust emissions. Large volumes of dust entrained by aerodynamic entrainment cannot only occur at low shear velocity without saltation, but may dominate the entrainment process in many arid and semi-arid environments. So it may also be responsible for large magnitude dust storms. Playa and alluvial fan landforms, prior to developing a surface crust, may be the main sources of dust storms in Qinghai Province.
基金Project partly supported by University of Balochistan, Pakistan
文摘Tightening of air quality standards for populated urban areas has led to increasing attention to assessment of air quality management areas, where violation of air quality standards occurs, and development of control strategies to eliminate such vio-lation of air quality standards. The Quetta urban area is very densely built and has heavy motorized traffic. The increase of emis-sions mainly from traffic and industry are responsible for the increase in atmospheric pollution levels during the last years. The dust examined in the current study was collected by both deposit gauge and Petri dish methods at various sites of Quetta Valley. Smoke particles were obtained by bladder method from the exhausts of various types of motor vehicles. The concentration of lead found in the smoke ranged from 1.5×10?6 to 4.5×10?6.
文摘This study evaluates the vertical profiles of aerosol and cloud optical properties in 40 dominated dust and smoke regions in Western-Northern Africa (WNA) and Central-Southern Africa (CSA), respectively, from the surface to 10km and from 2008 to 2011 based on LIVAS (LIdar climatology of Vertical Aerosol Structure for space-based lidar simulation studies). Aerosol extinction (AE), aerosol backscatter (AB), and aerosol depolarization (AD) generally increase from the surface to 1.2 km and decrease from 1.2 km to the upper layers in both WNA and CSA. AE and AB in CSA (maximum of 0.13 km<sup>-1</sup>, 0.14 km<sup>-1</sup>, 0.0021 km<sup>-1</sup>‧sr<sup>-1</sup>, 0.0033 km<sup>-1</sup>‧sr<sup>-1</sup>) are higher than in WNA (maximum of 0.07 km<sup>-1</sup>, 0.08 km<sup>-1</sup>, 0.0017 km<sup>-1</sup>‧sr<sup>-1</sup>, 0.0015 km<sup>-1</sup>‧sr<sup>-1</sup>) at 532 and 1064 nm respectively. AD in WNA (maximum of 0.25) is significantly higher than in CSA (maximum of 0.05). There is a smooth change with the height of cloud extinction and backscatter in WNA and CSA, while there is a remarkable increase of cloud depolarization with height, whereby it is high in CSA and low in WNA due to high and low fraction of cirrus respectively. Altocumulus has the highest extinction in NA (0.0139 km<sup>-1</sup>), CA (0.058 km<sup>-1</sup>), WA (0.013 km<sup>-1</sup>), while low overcast transparent (0.76 km<sup>-1</sup>) below 1 km in SA. The major findings of this study may contribute to the improvement of our understanding of aerosol-cloud interaction studies in dominated dust and smoke aerosol regions.
文摘With the rapid industrialization and urbanization,the demand for air quality management is more and more urgent.High temperature dust filtration is one important environmental management technology.Porous ceramics are used as filter materials in the field of high-temperature dust filtration because of their unique advantages such as high filtration efficiency,as well as high temperature stability,particle loss resistance,corrosion resistance and durability.This paper mainly introduced several common preparation techniques of porous ceramics,including the traditional organic foam impregnation method,foaming method,in-situ combustion method,pore-forming method and other new methods such as the template method,gel injection molding method,freeze-drying method,multi-component co-precipitation method and hydrogel method.The principle,advantages and disadvantages of these preparation technologies and their research status were described.The application of these technologies in the field of high temperature dust filtration was briefly reviewed.Finally,the application prospect of the porous ceramics in the field of high temperature dust filtration was prospected.