Effect of high magnetic field on phase transformation temperature and microstructure of Fe-based Alloys

The effect of a high magnetic field up to 30T on phase transformation temperature and microstructure of Fe-based alloys has been reviewed. A high magnetic field accelerates ferrite transformation, changes the morphology of the transformed microstructures and increases the A3 and A1 temperature. In a magnetic field of 30T, the A1 temperature increases by about 37.1℃ for Fe-0.8C, the A3 temperature for pure Fe increases by about 33.1℃. The measured transformation temperature data are not consistent with calculation results using Weiss molecular field theory. Ferrite grains are elongated and aligned along the direction of magnetic field in Fe-0.4C and Fe-0.6C alloys by ferrite transformation, but elongated and aligned structure was not found in pure Fe, Fe-0.05C alloy and Fe-1.5Mn-0.11C-0.1V alloy.

Thin Film Chip Resistors with High Resistance and Low Temperature Coefficient of Resistance

High resistance thin film chip resistors(0603 type) were studied,and the specifications are as follows:1 k? with tolerance about ±0.1% after laser trimming and temperature coefficient of resistance(TCR) less than ±15×10-6/℃.Cr-Si-Ta-Al films were prepared with Ar flow rate and sputtering power fixed at 20 standard-state cubic centimeter per minute(sccm) and 100 W,respectively.The experiment shows that the electrical properties of Cr-SiTa-Al deposition films can meet the specification requirements of 0603 ty...

Low temperature impact toughness of laser hybrid welded joint of high strength low alloy steel

High strength low alloy steel with 16 mm thickness was welded by using high power laser hybrid welding. Microstrueture was characterized by using optical microscopy, scanning electron microscopy （ SEM ） , transmission electron microscopy （TEM） and selected area electron diffraction （SAED）. Low temperature impact toughness was estimated by using Charpy V-notch impact samples selected from the upper part and the lower part at the same heterogeneous joint. Results show that the low temperature impact absorbed energies of weld metal are （202,180,165 J） of upper samples and （178,145,160 J） of lower samples, respectively. All of them increase compared to base metal. The embrittlement of HAZ does not occur. Weld metal primarily consists of refined carbide free bainite and a little granular bainite since laser hybrid welding owns the character of low heat input. Retained austenite constituent film ＂locates among the lath structure of bainitie ferrite. Refined bainitic ferrite lath and retained austenite constituent film provide better low temperature impact toughness compared to base metal.

Influence of heat treatment on high frequency soft magnetic properties of Finemet amorphous alloy

In order to study high-frequency soft magnetic properties of Finemet amorphous alloy,the microstructural change and nanocrystallization under different heat treatment conditions were investigated by XRD and TEM. The crystallite size of α-Fe was calculated from the XRD pattern using the Scherrer formula,while the high frequency magnetic properties were measured at room temperature by TPS-200SA exchange tester. The results of XRD and TEM indicate that the nanocrystallization occurs at 500 ℃. When the annealing temperature increases to 560 ℃,the amorphous alloy becomes totally nanocrystallized and the crystallites distribute homogeneously,thus an excellent combination of soft magnetic properties is obtained.

Recent progress in high temperature permanent magnetic materials

Permanent magnetic materials capable of operating at high temperature up to 500℃ have wide potential applications in fields such as aeronautics, space, and electronic cars. SmCo alloys are candidates for high temperature applications, since they have large magnetocrystalline anisotropy field （6-30 T）, high Curie temperature （720-920℃）, and large energy product （〉200 kJ.m-3） at room temperature. However, the highest service temperature of commercial 2：17 type SmCo magnets is only 300℃, and many efforts have been devoted to develop novel high temperature permanent magnets. This review focuses on the development of three kinds of SmCo based magnets： 2：17 type SmCo magnets, nanocrystalline SmCo magnets, and nanocomposite SmCo magnets. The oxidation protection, including alloying and surface modification, of high temperature permanent magnets is discussed as well.

Elevated temperature endurance and creep properties of extruded 2D70 Al alloy rods

The elevated temperature performances of 2D70 Al alloy hot extrusion rods after two-stage homogenization and intensive deformation were studied by measuring the elevated temperature enduring strength and the creep ultimate strength. The fracture morphology of some selected samples after testing at different elevated temperatures was observed by scanning electron microscopy （SEM）. The results indicate that, as the test temperature increases, the elevated temperature enduring strength of 2D70 Al alloy decreases gradually. In a comparison between 150 C and 240 C, the notch enduring strength drops from 375 to 185 MPa and the smooth enduring strength drops from 337 to 130 MPa. Enduring strength is not sensitive to the notch. The notch sensitivity ratio （NSR） coefficient is in the range of 1.119 to 1.423 from 150 C to 240 C. The creep test results show that, as the test temperature increases from 150 C to 240 C, the creep ultimate strength of 2D70 Al alloy rods drops gradually from 312 to 117 MPa.

Behavior of Medium-frequency Core Loss in Fe-based Nanocrystalline Soft Magnetic Alloys

The dependences of the power loss per cycle on frequency have been investigated in the ranges of 100 Hz<= f<=25000 Hz and 0.1 T< =Bm <=1.0 T for three main original magnetic states in five sorts of Fe-based nanocrystalline soft magnetic alloys. The measured and calculated results showed that the total power loss per cycle clearly exhibited a nonlinear behavior in the range below 3 kHz～5 kHz depending on both the magnetic state and the value of Dm, whereas it showed a quasi-linear behavior above this range. The total loss was decomposed into hysteresis loss, classical eddy current loss and excess loss, the obvious nonlinear behavior has been confirmed to be completely determined by the dependence of the excess loss on frequency. It has been indicated that the change rate of the excess loss per cycle with respect to frequency sharp decreases with increasing frequency in the range below about 3 kHz～5 kHz, wherease the rate of change slowly varies above this range, thus leading to the quasilinear behavior of the total loss per cycle. In this paper, some linear expressions of the total loss per cycle has been given in a wider medium-frequency segment, which can be used for roughly estimating the total loss.

Co_(47.5)Fe_(28.·5)Ni_(19)Si_(3.3)Al_(1.7)High-entropy Skeletons Fabricated by Selective Laser Melting and Properties tuned by pressure infiltration of Al

High saturation magnetization and low coercivity are required for soft magnetic materials.This study investigated the Co_(47.5)Fe_(28.5)Ni_(19)Si_(3.3)Al_(1.7)high-entropy soft magnetic skeleton was prepared by selective laser melting.Then Al wpressure infiltrated into skeletons to obtain a dense composite material.The high-entropy composite materials possessed favorable compressive ductility and moderate soft magnetic properties.The high-entropy composite materials were obtained with Ms being 97.1 emu/g,79.8 emu/g,33 emu/g and possessing 19 Oe,15.8Oe and 17Oe of Hc,respectively.However,the magnetostriction coefficient remains low level,about 5ppm.These reported properties are attributed to the special structure of the material studied in present experiment.Nevertheless,a novel strategy of structural designing was proposed in this paper.

Novel CoFeAlMn high-entropy alloys with excellentsoft magnetic properties and high thermal stability

High-entropy alloys(HEAs),which are composed of 3d transition metals such as Fe,Co,and Ni,exhibit an exceptional combination of magnetic and other properties;however,the addition of non-ferromagnetic elements always negatively affects the saturation magnetization strength(M s).Co_(4)Fe_(2)Al_(x)Mn_(y) alloys were designed and investigated in this study to develop a novel HEA with excellent soft magnetic properties.The Co_(4)Fe_(2)Al_(1.5)Mn_(1.5) HEA possesses the highest M s of 161.3 emu g^(-1) thus far reported for magnetic HEAs,a low coercivity of 1.9 Oe,a high electrical resistivity of 173μΩ cm,a superior thermal stability up to 600℃,which originates from the novel microstructure of B2 nanoparticles distributed in a DO_(3) matrix phase,and the crucial transition of Mn from antiferromagnetism to ferromagnetism with the assistance of Al.The Co_(4)Fe_(2_)Al_(1.5)Mn_(1.5) HEA was selected to produce micron-sized powder and soft magnetic powder cores(SMPCs)for application in the exploration field.The SMPCs exhibit a high stable effective perme-ability of 35.9 up to 1 MHz,low core loss of 38.1 mW cm^(-3)(@100 kHz,20 mT),and an excellent direct current(DC)bias performance of 87.7%at 100 Oe.This study paves the way for the development of soft magnetic HEAs with promising applications as magnetic functional materials.

Ultra-thin Laminated Metal Composites with Ultra-high Strength and Excellent Soft Magnetic Properties

Structural metallic materials with excellent functional performance and lightweight features have always been the goal of material scientists’ pursuit.In this work,laminated metal composites of different thicknesses(less than 0.4 mm) composed of structural materials with great differences in deformation ability were successfully fabricated via a novel processing procedure.Ultra-high strength and excellent soft magnetic properties were combined perfectly in the ultra-thin and super-light laminated metal composite strips due to unique structural design and essential attributes of the initial materials.These results emphasize the significant potential application value of the ultra-thin laminated metal composites in the field of structural and functional integration.

Lattice distortion and magnetic property of high entropy alloys at low temperatures

Deformation mechanisms and magnetic properties of medium and high entropy alloys(MEA/HEAs)closely relate to lattice distortion and are strongly temperature-dependent,in particular,at low temperature ranges.However,little attention has been paid to the evolution of lattice distortion with temperature decreasing and its effects on deformation behavior and magnetic state transition.In this work,we carry out in situ synchrotron radiation based X-ray powder diffraction(SR-XRD)experiments from 293 to 123 K aiming for determining lattice distortion evolutions of Cr Co Ni MEA,Cr Fe Co Ni and Cr Mn Fe Co Ni HEAs.Magnetic measurements at corresponding low temperatures and cryogenic ranges are further conducted.The in situ SR-XRD results demonstrate a general reduction of lattice distortion magnitude with temperature decreasing,which shows a similar tendency with that of reported stacking fault energy(SFE)values.It is thus suggested that lattice distortion reduction possibly makes a critical contribution to deformation mechanism transition.The magnetic measurement results show a clear ferromagnetic transition of Cr Fe Co Ni HEA when temperature is below 173 K.While,no obvious magnetic state transition is observed for Cr Co Ni MEA and Cr Mn Fe Co Ni HEA.The present findings on lattice distortion evolutions will pave the way for designing targeted HEAs with particular properties.

Room-temperature and high-temperature magnetic permeability of Co-doped nanocrystalline alloys

Influence of composition and annealing temperature on structure and magnetic properties of amorphous and nanocrystalline Fe78.4-xCoxSi9B9Nb2.6Cu1 （x=27.4, 40.0, 51.0, 78.4） alloys was investigated by X-ray diffraction （XRD） and the temperature dependence of permeability. According to the initial crystallization temperature （Tx1） from differential scanning calorimetry （DSC） curves of as-quenched amorphous alloys, 490-700 ℃ isothermal annealing was carded out to obtain the characteristic nanocrystalline structure. Furthermore, the soft magnetic properties were measured by temperature evolution of magnetic permeability to obtain the correlation between Co content, annealing temperature and magnetic permeability. The results show that, on the one hand, the annealing temperature exerts a significant effect on phase structure and initial permeability （μi）. The higher-temperature （from 550 to 610 ℃） annealed Co content nanocrystalline samples can remain higher μi at elevated temperature. On the other hand, partial substitution Fe by Co can improve the high-temperature magnetic stability;however, the room-temperature permeability of higher Co content alloys decreases obviously at the same time. This phenomenon was analyzed from the viewpoint of the saturation magnetic induction （Bs）, magnetic anisotropy （〈K〉） and magnetostriction （λs）.

Hot-press sintering of MA Fe-based nanocrystalline/amorphous soft magnetic powder

Microstructures and magnetic properties of Fe84Nb7B9,Fe80Ti8B 12 and Fe32Ni36（Nb/V）7Si8B17 powders and their bulk alloys prepared by mechanical alloying（MA） method and hot-press sintering were studied. The results show that: 1) After MA for 20 h,nanocrystalline bcc singl e phase supersaturated solid solution forms in Fe84-Nb7B9 and Fe8 0Ti8B12 alloys,amorphous structure forms in Fe32Ni36Nb7 Si8B17 alloy,duplex microstructure composed of nanocrystalline γ- （FeNi） supersaturated solid solution and trace content of Fe2B phase forms in Fe32Ni36-V7Si8B17 alloy. 2) The decomposition process of supersaturated solid solution phases in Fe84Nb7B9 and Fe80Ti8B 12 alloys happens at 710780 ℃,crystallization reaction in Fe （32）Ni36Nb7Si8B17 alloy happens at 530 ℃（the temperature of peak value） and residual amorphous crystallized further happens at 760 ℃ （the temperature of peak value）,phase decomposition process of supersaturated solid solution at 780 ℃ （the temperature of peak value） and crystallization reaction at 431 ℃ （the temperature of peak value） happens in Fe32Ni36V7S i8B17 alloy. 3) under 900 ℃,30 MPa,（0.5 h） hot-press sintering conditions,bulk alloys with high relative density（94.7%95.8%） can be ob tained. Except that the grain size of Fe84Nb7B9 bulk alloy is large,s uperfine grains （grain size 50200 nm） are obtained in other alloys. Exc ept that single phase microstructure is obtained in Fe80Ti8B12 bul k alloy,multi-phase microstructures are obtained in other alloys. 4) The magne tic properties of Fe80Ti8B12bulk alloy（Bs=1.74 T,Hc= 4.35 kA/m） are significantly superior to those of other bulk alloys,which is r elated to the different phases of nanocrystalline or amorphous powder formed dur ing hot-press sintering process and grain size.

ADVANCED NICKEL-BASED AND NICKEL-IRON-BASED SUPERALLOYS FOR CIVIL ENGINEERING APPLICATIONS

The use of high-temperature materials is especially important in power station construction, heating systems engineering, furnace industry, chemical and petrochemical industry, waste incineration plants, coal gasification plants and for flying gas turbines in civil and military aircrafts and helicopters. Particularly in recent years, the development of new processes and the drive to improve the economics of existing processes have increased the requirements significantly so that it is necessary to change from well-proven materials to new alloys. Hitherto, heat resistant ferritic steels sufficed in conventional power station constructions for temperatures up to 550℃ newly developed ferritic/martensitic steels provide sufficient strength up to about 600 - 620℃. In new processes, e.g. fluidized-bed combustion of coal, process temperatures up to 900℃ occur. However, this is not the upper limit, since in combustion engines, e.g. gas turbines. Material temperatures up to 1100℃ are reached locally. Similar development trends can also be identified in the petrochemical industry and in the heat treatment and furnace engineering. The advance to ever higher material temperatures now not only has the consequence of having to use materials with enhanced high-strength properties, considerable attention now also has to be given to their chemical stability in corrosive media. Therefore not only examples of the use of high-temperature alloys for practical applications will be given but also be contributed to some general rules for material selection with regard to their high-temperature strength and corrosion resistance.

Composition and phase structure dependence of mechanical and magnetic properties for AlCoCuFeNi_x high entropy alloys

In this study, the effects of composition and phase constitution on the mechanical properties and magnetic performance of AlCoCuFeNix(x = 0.5, 0.8, 1.0, 1.5, 2.0, 3.0 in molar ratio) high entropy alloys(HEAs)were investigated. The results show that Ni element could lead to the evolution from face centered cubic(FCC), body centered cubic(BCC) and ordered BCC coexisting phase structure to a single FCC phase. The change of phase constitution enhances the plasticity but reduces the hardness and strength. One of the interesting points is the excellent soft magnetic properties of AlCoCuFeNixHEAs. Soft magnetic performance is dependent on composition and phase transition. AlCoCuFeNi1.5 alloy, achieving a better balance of mechanical and magnetic properties, could be applied as structure materials and soft magnetic materials(SMMs). High Curie temperature(>900 K) and strong phase stability below 1350 K of AlCoCuFeNi0.5 alloy confirm its practicability in a high-temperature environment. Atomic size difference(δ) is utilized as the critical parameter to explain the lattice strain and phase transformation induced by Ni addition.

Correlation of Microstructure Feature with Impact Fracture Behavior in a TMCP Processed High Strength Low Alloy Construction Steel

The present article aims at elucidating the effect of thermo-mechanical controlled processing(TMCP), especially the finish cooling temperature, on microstructure and mechanical properties of high strength low alloy steels for developing superior low temperature toughness construction steel. The microstructural features were characterized by scanning electron microscope equipped with electron backscatter diffraction, and the mechanical behaviors in terms of tensile properties and impact toughness were analyzed in correlation with microstructural evolution. The results showed that the lower finish cooling temperature could lead to a considerable increase in impact toughness for this steel. A mixed microstructure was obtained by TMCP at lower finish cooling temperature, which contained much fine lath-like bainite with dot-shaped M/A constituent and less granular bainite and bainite ferrite. In this case, this steel possesses yield and ultimate tensile strengths of ~ 885 MPa and 1089 MPa, respectively, and a total elongation of ~ 15.3%, while it has a lower yield ratio of ~ 0.81. The superior impact toughness of ~ 89 J at-20 °C was obtained, and this was resulted from the multi-phase microstructure including grain refinement, preferred grain boundaries misorientation, fine lath-like bainite with dot-shaped M/A constituent.

Effect of Solid Solution Treatment on Microstructure of Fe-Ni Based High Strength Low Thermal Expansion Alloy

The influence of solid solution treatments on the dissolution of carbides precipitates,the grain size,and the hardness of high strength low expansion alloy were investigated through XRD analysis,microstructure observations,and theoretical computation.It was seen that most primary Mo2C type carbide band dissolved in a temperature range of 1 100-1 150 ℃.When the temperature was over 1 200 ℃,the grain size increased remarkably,which led to the reduction of hardness.

The influence of Si substitution on soft magnetic properties and crystallization behavior in Fe_(83)B_(10)C_(6-x)Si_xCu_1 alloy system

In this study, the soft magnetic properties and crystallization behavior of Fes3B10C6-xSixCul （x=0-4） nanocrystalline alloys prepared by annealing the melt-spun amorphous ribbons have been investigated. It is found that in the Fe83B10C6-xSixCU1 alloy system, the coercivity （Hc） decreases slightly with increasing Si addition and exhibits a minimum value with composition of x = 2, while the effective permeability （Ue） shows an opposite variation trend. The saturation magnetic flux density （Bs） shows a slightly decreasing trend owing to the decreasing volume fraction of nanocrystalline phase. The Fe83B10CaSi2Cu1 nanocrystalline alloy exhibits excellent soft magnetic properties with a high Bs of 1.78 T, high ue of 13 600 and low Hc of 4 A/m.

Effect of High Magnetic Field on Solidified Structure and Properties of Cu-Cr In Situ Composite

The microstructure of ripening processed Cu-15%Cr alloys and deformed samples were examined under a 12T high magnetic field.The high magnetic field has accelerated the Ostwald Ripening process of Cr phase,the Cr-rich particles in 12T HMF case are coarser compared with 0T case.The 12T high magnetic field increased the peak strength of Cu(111)crystal plane and Cr(110)crystal plane,and appeared to has an orientation effect.Compared with the 0T case, the 12T high magnetic field case decreased the tensile strength and hardness.

Tensile ductility improvement of AlSi9Cu1 alloy by chemical composition optimization

Diesel engines, characterized by higher breakout pressure and compression ratio in comparison with gasoline engines, require particularly elevated tensile properties for their engine parts. In order to maintain both high strength and high ductility in the cylinder head, i.e., to obtain higher percent elongation without further reducing the tensile strength, Al Si9Cu1 alloy was used to prepare the cylinder head in an aluminum diesel engine. At the same time, the effect of different modification elements, Na or Sr, and Fe content on the reduction of secondary dendrite arm spacing(SDAS) was discussed, and the design of T7 heat treatment parameters were analyzed in order to improve the tensile ductility. The result shows:(1) The SDAS is as small as 18±3 μm for the Sr modified alloy.(2) The percent elongation of the alloy with Sr modification increases by 66.7% and 42.9%, respectively, compared with the unmodified alloy and the alloy with Na modification.(3) Lower Fe content alloy(0.10%) gives good results in percent elongation compared to the alloy with higher Fe content(0.27%); in particular, after Sr modification and T7 heat treatment, the elongation of over 5% is obtained.