Edge detection and mathematic fitting for corneal surface with Matlab software

AIM：To select the optimal edge detection methods to identify the corneal surface,and compare three fitting curve equations with Matlab software. METHODS：Fifteen subjects were recruited. The corneal images from optical coherence tomography（OCT）were imported into Matlab software. Five edge detection methods（Canny,Log,Prewitt,Roberts,Sobel）were used to identify the corneal surface. Then two manual identifying methods（ginput and getpts）were applied to identify the edge coordinates respectively. The differences among these methods were compared. Binomial curve（y=Ax2＋Bx＋C）,Polynomial curve [p（x）=p1xn＋p2x（n-1）＋....＋pnx＋pn＋1] and Conic section（Ax2＋Bxy＋Cy2＋Dx＋Ey＋F=0）were used for curve fitting the corneal surface respectively. The relative merits among three fitting curves were analyzed. Finally,the eccentricity（e）obtained by corneal topography and conic section were compared with paired t-test. RESULTS：Five edge detection algorithms all had continuous coordinates which indicated the edge of the corneal surface. The ordinates of manual identifying were close to the inside of the actual edges. Binomial curve was greatly affected by tilt angle. Polynomial curve was lack of geometrical properties and unstable. Conic section could calculate the tilted symmetry axis,eccentricity,circle center,etc. There were no significant differences between ＇e＇ values by corneal topography and conic section（t=0.9143,P=0.3760 〉0.05）.CONCLUSION：It is feasible to simulate the corneal surface with mathematical curve with Matlab software. Edge detection has better repeatability and higher efficiency. The manual identifying approach is an indispensable complement for detection. Polynomial and conic section are both the alternative methods for corneal curve fitting. Conic curve was the optimal choice based on the specific geometrical properties.

Calculating the proportion of Nd-rich phase in NdFeB alloy via Matlab software

Nd-rich phase plays an important role in the magnetic properties of sintered NdFeB alloy. The proportion of Nd-rich phase to all the other phases was calculated by using MATLAB 6.5 software. Especially, post-sintered alloy, post-high-temperature tempered alloy and post-high and low-temperature tempered alloy were analyzed. It was found that the proportion of Nd-rich phase in the three alloys based on SEM (scanning electron microscope) images was about 8.22%, 8.03% and 8.00%, respectively.

Comparative Studies between Picard’s and Taylor’s Methods of Numerical Solutions of First Ordinary Order Differential Equations Arising from Real-Life Problems

To solve the first-order differential equation derived from the problem of a free-falling object and the problem arising from Newton’s law of cooling, the study compares the numerical solutions obtained from Picard’s and Taylor’s series methods. We have carried out a descriptive analysis using the MATLAB software. Picard’s and Taylor’s techniques for deriving numerical solutions are both strong mathematical instruments that behave similarly. All first-order differential equations in standard form that have a constant function on the right-hand side share this similarity. As a result, we can conclude that Taylor’s approach is simpler to use, more effective, and more accurate. We will contrast Rung Kutta and Taylor’s methods in more detail in the following section.

Attribute Reduction in Decision Systems Based on Relation Matrix

This paper proposes,from the viewpoint of relation matrix,a new algorithm of attribute reduction for decision systems.Two new and relative reasonable indices are first defined to measure significance of the attributes in decision systems and then a heuristic algorithm of attribute reduction is formulated.Moreover,the time complexity of the algorithm is analyzed and it is proved to be complete.Some numerical experiments are also conducted to access the performance of the presented algorithm and the results demonstrate that it is not only effective but also efficient.

Trajectory Optimization and Motion Simulation of a Flexible Polishing Industrial Robot for Watchcases

To optimize the working time of the flexible polishing industrial robot for watchcases,the polishing efficiency should be improved.Based on the quintic B-spline fitting curve trajectory planning method associated with the optimal time interval and the trajectory point angle,the trajectory route of the flexible polishing industrial robot for case parts was optimized by the Matlab software.The operation time of the flexible polishing industrial robot could reach the optimal level.The joints of the robot can be cooperated with each other to ensure that the motion track of the end-effector of the robot arm is closer to the expected motion track.Based on the Adams software,the obtained trajectory curve of multi-objective optimization was simulated,which verified the trajectory fitted after multi-objective optimization.The angular acceleration and angular plus acceleration curves were improved.Theoretical guidance was carried out for the subsequent experiment by Matlab and Adams simulation analysis.

Research on Site Planning of Mobile Communication Network

With the development of 5G technology, network communication has become the most commonly used tool in People’s Daily life and production. Due to the huge user base, the problem of site selection of communication network has become more and more complex. This paper mainly studies the problem of mobile communication network site planning, using 0 - 1 planning knapsack model, heuristic algorithm, simulated annealing algorithm and other methods, combined with MATLAB software to effectively solve the location of site coordinates and the type of base station selection, give the optimal results of site selection. It has certain guiding significance to mobile communication network site planning.

Process Simulation and Microstructure Analysis of Low Carbon Si-Mn Quenched and Partitioned Steel

The quenching and partitioning （Q＆P） process was experimentally investigated on the thermomechanical simulator （Gleeble3800）. The microstructure and fracture mechanism of the sheets were investigated by means of TEM. It was found that the microstructure of quenched and partitioned steel consists of fine lath martensite and thin inter-lath austenite films. The optimum quenching temperature of producing the maximum amount of retained austenite after final quenching at room temperature was predicted by Matlab software package. It was found that the calculations by Matlab software can provide guidance for experimental processing design reliably. The volume fraction of retained austenite at room temperature was approximately 8%, which was measured easily by the software VC6.0＋＋ programming. The results verified that quenched and partitioned steel possesses a good combination of strength and plasticity due to its fine microstructure. This steel exhibited high ultimate tensile strength （exceeding 1 000 MPa） and good elongation of 25%. The results showed that the fracture mechanism of the sheets is typical tough fracture under the condition of tensile failure.