Seismic stability of expansive soil slopes reinforced by anchor cables using a modified horizontal slice method

Earthquake-induced slope failures are common occurrences in engineering practice and pre-stressed anchor cables are an effective technique in maintaining slope stability,especially in areas that are prone to earthquakes.Furthermore,the soil at typical engineering sites also exhibit unsaturated features.Explicit considerations of these factors in slope stability estimations are crucial in producing accurate results.In this study,the seismic responses of expansive soil slopes stabilized by anchor cables is studied in the realm of kinematic limit analysis.A modified horizontal slice method is proposed to semi-analytically formulate the energy balance equation.An illustrative slope is studied to demonstrate the influences of suction,seismic excitations and anchor cables on the slope stability.The results indicate that the stabilizing effect of soil suction relates strongly to the seismic excitation and presents a sine shape as the seismic wave propagates.In higher and steeper slopes,the stabilizing effect of suction is more evident.The critical slip surface tends to be much more shallow as the seismic wave approaches the peak and vice versa.

Novel protection systems for the improvement in soil and water stability of expansive soil slopes

To improve the soil and water stability of expansive soil slopes and reduce the probability of slope failure,novel protection systems based on polymer waterproof coatings(PWC)were used in this study.Herein,three groups of expansive soil slope model tests were designed to investigate the effects of polyester nonwovens and PWC(P-PWC)composite protection system,three-dimensional vegetation network and PWC(T-PWC)composite protection system,and nonprotection on the soil and water behavior in the slopes under precipitation–evaporation cycles.The results showed that the moisture change of P-PWC and T-PWC composite protected slopes was significantly smaller than that of bare slope,which reduced the sensitivity of slope moisture to environmental changes and improved its stability.The soil temperature of the slope protected by the P-PWC and T-PWC systems at a depth of 70 cm increased by 5.6℃ and 2.7℃,respectively.Using PWC composite protection systems exhibited better thermal storage performance,which could increase the utilization of shallow geothermal resources.Moreover,the maximum average crack widths of the bare slopes were 7.89 and 3.17 times those of the P-PWC and TPWC protected slopes,respectively,and the maximum average crack depths were 6.87 and 3 times those of the P-PWC and T-PWC protected slopes,separately.The PPWC protection system weakened the influence of hydro–thermal coupling on the slopes,inhibited the development of cracks on the slopes,and reduced the soil erosion.The maximum soil erosion of slopes protected by P-PWC and T-PWC systems was 332 and 164 times lower than that of bare slope,respectively.The P-PWC and T-PWC protection systems achieved excellent"anti-seepage and moisture retention"and anti-erosion effects,thus improving the soil and water stability of slopes.These findings can provide important guiding reference for controlling rainwater infiltration and soil erosion in expansive soil slope projects.

Effectiveness of Fiber Bragg Grating monitoring in the centrifugal model test of soil slope under rainfall conditions

Centrifugal model testsare playing an increasingly importantrolein investigating slope characteristics under rainfall conditions. However, conventional electronic transducers usually fail during centrifugal model tests because of the impacts of limitedtest space, high centrifugal force, and presence of water, with the result that limited valid data is obtained. In this study, Fiber Bragg Grating(FBG) sensing technology is employed in the design and development of displacement gauge, an anchor force gauge and an anti-slide pile moment gauge for use on centrifugal model slopes with and without a retaining structure. The two model slopes were installed and monitored at a centrifugal acceleration of 100 g. The test results show that the sensors developed succeed in capturing the deformation and retaining structure mechanical response of the model slopes during and after rainfall. The deformation curvefor the slope without retaining structure shows a steepresponse that turns gradualfor the slope with retaining structure. Importantly, for the slope with the retaining structure, results suggest that more attention be paid to increase of anchor force and antislide pile moment during rainfall. This study verifies the effectiveness of FBG sensing technology in centrifuge research and presents a new and innovative method for slope model testing under rainfall conditions.

Simplified method for analyzing soil slope deformation under cyclic loading

Reasonable assessment of slope deformation under cyclic loading is of great significance for securing the safety of slopes. The observations of centrifuge model tests are analyzed on the slope deformation behavior under cyclic loading conditions. The potential slip surface is the key for slope failure and follows two rules:(i) the relative horizontal displacement along the potential slip surface is invariable at an elevation, and(ii) the soil along the slip surface exhibits the same degradation pattern. These rules are effective regardless of the location of the potential slip surface throughout the entire deformation process of a homogeneous slope, ranging from the initial deformation stage to the failure process and to the post-failure stage. A new, simplified method is proposed by deriving the displacement compatibility equation and unified degradation equation according to the fundamental rules. The method has few parameters that can be determined through traditional element tests. The predictions from the proposed method agree with the centrifuge test results with vertical loading and shaking table loading. This result confirms that the proposed method is effective in predicting the full deformation process of slopes under different cyclic loading conditions.

Influence of Soil Heterogeneity on the Behavior of Frozen Soil Slope under Freeze-Thaw Cycles

Soil slope stability in seasonally frozen regions is a challenging problem for geotechnical engineers.The freezethaw process of soil slope caused by the temperature fluctuation increases the difficulty in predicting the slope stability because the soil property is influenced by the freeze-thaw cycle.In addition,the frozen soil,which has ice crystal,ice lens and experienced freeze-thaw process,could present stronger heterogeneity.Previous research has not investigated the combined effect of soil heterogeneity and freeze-thaw cycle.This paper studies the influence of soil heterogeneity on the stability of frozen soil slope under freeze-thaw cycles.The local average subdivision(LAS)is utilized to model the soil heterogeneity.A typical slope geometry has been chosen and analysed as an illustrative example and the strength reduction method is used to calculate the factor of safety(FOS)of slope.It has been found that when the temperature is steady,the FOS of the frozen soil slope is influenced by the spatial variability of the thermal conductivity,but the influence is not significant.When the standard deviation and the SOF of the thermal conductivity increase,the mean of the FOS is equal to the FOS of the homogeneous case and the standard deviation of the FOS also increases.After the frozen soil goes through freeze-thaw process,the FOS of the frozen soil slope decreases due to the reduction in the cohesion and the internal friction angle caused by the freeze-thaw cycles.Furthermore,the decreasing ratio of the FOS becomes more scattered after the 5th freeze-thaw cycle compared to that of the FOS after the 1st freeze-thaw cycle.The larger variability of the FOS could induce inaccuracy in the prediction of the frozen soil slope stability.

Determination of a Mathematical Model of Erosion Taking into Account the Intensity of Rainfall and Soil Slopes from the Global MNT Model

Our study is being carried out in the Wouri Estuary more precisely in the Nylon area, Douala. This area is influenced by abundant rainfall which promotes the phenomenon of rain erosion. This erosion contributes to the degradation of structures and soils. To better understand and predict this phenomenon of rainfall erosion, we set out to establish a mathematical model that takes into account precipitation and topography. To this end, the data collected in the field and in the laboratory made it possible. First, we graphically modeled the variation of the potential as a function of the intensity of rainfall and the slope of the ground. Next, we identified a mathematical model from cubic spline surface interpolation. Finally, we obtained the mathematical model which makes it possible to evaluate and predict the erosion potential. The results obtained allowed to have an erosion potential of 153.67 t/ha/year with field data and 153.94 t/ha/year with laboratory data. We compared the results obtained with those existing in the literature on the same study site. This comparison made it possible to validate the established mathematical model. This mathematical model is a decision support tool and can predict problems related to water, erosion and the environment.

Influence of the ground flora on the variation characteristics of the runoff distribution on red soil slope

In this paper, we use the inter flow area as the research object in the logical science park for soil and water conservation in Jiangxi province; and the Paspalum natatum and its litter cover are used as the ground flora. We discusses and analyses the vertical distribution of runoff so as to provide theoretical support for the wide application of the Paspalum natatum for soil and water conservation in the region of red soil in south China.

Infiltration regulation and stability analysis of soil slope under sustained and small intensity rainfall

Rainfall infiltration depth and mode can severely influence slope stability.With the sustained rainfall,the influenced region of slope gradually expands.By using the Green-Ampt model to the soil slope,infiltration regulation was discussed under sustained and small intensity rainfall.And the infiltration rate of unsaturated soil was proposed according to the saturated infiltration theory.Because of the changing of initial moisture content in depth of slope,the saturated or unsaturated infiltration rate and depth could also be changeable with the sustained rainfall infiltration.Based on the principle of strength reduction,the calculation model of slope safety factor was established under different initial moisture contents and infiltration modes.Then,the slope stability was quantitatively analyzed through software FLAC3D.The calculation results of soil slope engineering show that there is a shorter period for slope stability under different initial moisture contents and unsaturated infiltration ways at the slope wetting front.The stability period of slope is 33.3%according to different initial moisture contents of wetting front less than that of the same initial moisture content of wetting front.And the slope is easier to fail under the unsaturated infiltration.The results agree well with the actual situation under sustained and small intensity rainfall.

Stability analysis of unsaturated soil slope during rainfall infiltration using coupled liquid-gas-solid three-phase model

Generally, most soil slope failures are induced by rainfall infiltration, a process that involves interactions between the liquid phase, gas phase,and solid skeleton in an unsaturated soil slope. In this study, a loosely coupled liquid-gas-solid three-phase model, linking two numerical codes,TOUGH2/EOS3, which is used for water-air two-phase flow analysis, and FLAC^(3D), which is used for mechanical analysis, was established. The model was validated through a documented water drainage experiment over a sandy column and a comparison of the results with measured data and simulated results from other researchers. The proposed model was used to investigate the features of water-air two-phase flow and stress fields in an unsaturated soil slope during rainfall infiltration. The slope stability analysis was then performed based on the simulated water-air two-phase seepage and stress fields on a given slip surface. The results show that the safety factor for the given slip surface decreases first, then increases, and later decreases until the rainfall stops. Subsequently, a sudden rise occurs. After that, the safety factor decreases continually and reaches its lowest value, and then increases slowly to a steady value. The lowest value does not occur when the rainfall stops, indicating a delayed effect of the safety factor. The variations of the safety factor for the given slip surface are therefore caused by a combination of pore-air pressure, matric suction, normal stress, and net normal stress.

A Method Combining Numerical Analysis and Limit Equilibrium Theory to Determine Potential Slip Surfaces in Soil Slopes

This paper describes a precise method combining numerical analysis and limit equilibrium theory to determine potential slip surfaces in soil slopes. In this method, the direction of the critical slip surface at any point in a slope is determined using the Coulomb’s strength principle and the extremum principle based on the ratio of the shear strength to the shear stress at that point. The ratio, which is considered as an analysis index, can be computed once the stress field of the soil slope is obtained. The critical slip direction at any point in the slope must be the tangential direction of a potential slip surface passing through the point. Therefore, starting from a point on the top of the slope surface or on the horizontal segment outside the slope toe, the increment with a small distance into the slope is used to choose another point and the corresponding slip direction at the point is computed. Connecting all the points used in the computation forms a potential slip surface exiting at the starting point. Then the factor of safety for any potential slip surface can be computed using limit equilibrium method like Spencer method. After factors of safety for all the potential slip surfaces are obtained, the minimum one is the factor of safety for the slope and the corresponding potential slip surface is the critical slip surface of the slope. The proposed method does not need to pre-assume the shape of potential slip surfaces. Thus it is suitable for any shape of slip surfaces. Moreover the method is very simple to be applied. Examples are presented in this paper to illustrate the feasibility of the proposed method programmed in ANSYS software by macro commands.

Reasonable selection of yield criteria for quantitative analysis of unsaturated soil slope stability

The yield criterion parameters of the soil material change with different values of the cohesion and the angle of friction because of sustained rainfall infiltration. Based on the Mohr-Coulomb(M-C) and Drucker-Prager(D-P) yield criteria, some reasonable yield criteria selections were discussed for quantitative analysis of unsaturated soil slope stability. Moreover, a critical point was found at the effective angle of friction equaling to 16.5° by transformation of parameters related to unsaturated soil under sustained rainfall. When the effective angle of friction more than 16.5° through parameter transformation of different yield criteria under natural condition, the calculation result of the safety factor was such that: f(DP1) > f(M-C) > f(equivalent M-C) > f(DP2) > f(DP3). While the effective angle of friction less than 16.5°, through parameter transformation, the safety factors were in the following order: f(DP1) > f(M-C) > f(DP2) > f(equivalent M-C) > f(DP3). The calculated results from a case study showed that the equivalent M-C yield criterion should be the best at evaluating soil slope stability before rainfall; the DP2 yield criterion should be selected to calculate the soil slope stability at the effective angle of friction less than 16.5° under sustained rainfall. The yield criterion should be selected or adjusted reasonably to calculate the safety factor of unsaturated soil slopes before and during sustained rainfall.

A pseudo-coupled numerical approach for stability analysis of frozen soil slopes based on finite element limit analysis method

To simplify the stability analysis of frozen soil slope, a pseudo-coupled numerical approach is developed. In this approach, the coupled heat transfer and water flow in frozen soils are simulated first, and based on the computed thermal-hydro field, the stability of frozen soil slope is evaluated. Although the shear strength for frozen soil is very complicated and is usually represented by a nonlinear MC failure criterion, a simple linear MC yield criterion is utilized. In this method, the internal friction angle is expressed as a function of volumetric ice content and the cohesion is fitted as a simple bilinear expression of T and volumetric water content. To assess slope stability, the limit analysis is employed in conjunction with the recently developed α-section search algorithm. A frozen soil slope example is used to examine the proposed pseudo-coupled numerical approach, and numerical studies validate its effectiveness. Based on numerical results, it is seen that slope stability may be remarkably influenced by warming air (or ground surface) temperature. With increasing ground surface temperature, slope stability indicated by FOS may reduce to 1.0, implying that warming air temperature could be a trigger of frozen soil slope failure.

Upper Bound Solution of Soil Slope Stability under Coupling Effect of Rainfall and Earthquake

Based on the limit analysis upper bound method,a new model of soil slope collapse has been proposed which consists of two rigid block zones and a plastic shear zone.Soil slope was induced failure by coupling effect of rainfall and earthquake,and these blocks were also incorporated horizontal earthquake force and vertical gravitate.The velocities and forces were analyzed in three blocks,and the expression of velocity discontinuities was obtained by the principle of incompressibility.The external force work for the blocks,the internal energy of the plastic shear zone and the velocity discontinuous were solved.The present stability ratios are compared to the prevenient research,which shows the superiority of the mechanism and rationality of the analysis.The critical height of the soil slope can provide theoretical basis for slope support and design.

Back analysis for soil slope based on measuring inclination data

Based on the analysis of several objective functions,a new method was proposed.Firstly,the feature of the inclination curve was analyzed.On this basis,the soil could be divided into several blocks with different displacements and deformations.Then,the method of the soil division was presented,and the characteristic of single soil block was studied.The displacement of the block had two components:sliding and deformation.Moreover,a new objective function was constructed according to the deformation of the soil block.Finally,the sensitivities of the objective functions by traditional method and the new method were calculated,respectively.The result shows that the new objective function is more sensitive to mechanical parameters and the inversion result is close to that obtained by the large direct shear apparatus.So,this method can be used in slope back analysis and its effectiveness is proved.

Effect of the frozen layer on the stability of cut soil slopes during seasonal freezing and thawing

Research on the stability of soil slopes in seasonally frozen regions has mainly focused on slope failures during the thawing window.There are few studies on slope stability during the freezing window and its subsequent influence on slope failure in the next thawing window.In this paper,soil strength was tested during freezing and thawing to obtain temperature-dependent strength parameters for the simulation of slope stability.Then,the slope's temperature field over an entire year was accurately simulated so that characteristics of the frozen layer could be determined at any time.Based on the above results,the progressive failure modes of frozen soil slopes are discussed.The results show that:1)during the freezing window,depth of the frozen soil layer increases,as does the slope's safety factor,while a yield zone propagates towards the slope shoulder.(2)During the thawing window,the frozen soil layer shrinks in depth while the yield zone continuously expands,which decreases the safety factor.Comprehensive analysis of these results indicate that the frozen layer provides a“toe-locking effect”that increases the safety factor during the freezing window,while it also provides a“dragging effect”that propagates the yield zone towards the slope shoulder.During the thawing window,the“toe-locking effect”gradually diminishes;a continuous sliding surface is formed,which lead to a landslide.The frozen soil layer of the freezing window accelerates the slope sliding in the thawing window.

Numerical Simulation of Moisture Movement in Unsaturated Expansive Soil Slope Suffering Permeation

This study develops a way of analyzing moisture movement in unsaturated expansive soil slope. The basic equations and the integrated finite difference method for moisture movement in unsaturated soils are briefly described, and the calculation code MFUS2 has been developed. The moisture movements in unsaturated expansive soil slopes suffering precipitation were simulated numerically. The simulation results show that expansion or contraction must be taken into account in an analysis model. A simplified equivalent model for calculating rainwater infiltration into expansive soil slopes has been developed. The simplified equivalent model divides the soil slope into two layers according to the extent of weathering of the soil mass at depth. Layer Ⅰ is intensively weathered and moisture can be fully evaporated or rapidly absorbed. The moisture movement parameters take into account the greater soil permeability caused by fissures. Layer Ⅱ is unweathered and the soil is basically undisturbed. The moisture movement parameters of homogeneous soils are applicable. The moisture movements in unsaturated expansive soil slopes suffering precipitation were simulated numerically using the simplified equivalent model. The simulation results show that the moisture movement in the expansive soil slope under rainfall permeation mainly takes place in the extensively weathered layer Ⅰ, which closely simulates the real situation.

Analytical expressions for determining the stability of cohesionless soil slope under generalized seismic conditions

In recent major earthquakes, the researchers have found the need for consideration of vertical seismic acceleration for the stability analysis of the man-made and natural slopes. However, in most past studies, the performance of slopes has been assessed by accounting only the horizontal seismic component of the ground motion, without giving due weightage to the effect of vertical component. In the present study, analytical expressions are derived to determine the factor of safety, yield seismic coefficient and consequently the seismic displacement of cohesionless soil slope under combined horizontal and vertical components of the ground motion. The derivation uses the Newmark's sliding block approach, in which the soil slope with a planar failure surface within the framework of conventional pseudo-static analysis is assumed to follow the Mohr-Coulomb failure criterion. The effects of vertical seismic coefficient on the stability of cohesionless slope have been studied through a set of graphical presentations for a specific range of soil parameters. It is observed that overlooking the effect of the vertical component of the ground motion on factor of safety and the displacement while designing the slope may be detrimental, resulting in the slope failure. The general expressions presented in this paper may be highly useful in the field of earthquake geotechnical engineering practice for designing the cohesionless soil slopes under combined horizontal and vertical seismic loads.

STRUCTURAL DAMAGE MODEL OF UNSATURATED EXPANSIVE SOIL AND ITS APPLICATION IN MULTI-FIELD COUPLE ANALYSIS ON EXPANSIVE SOIL SLOPE

Focused on the sensitivity to climate change and the special mechanical characteristics of undisturbed expansive soil, an elastc-plastic damage constitutive model was proposed based on the mechanics of unsaturated soil and the mechanics of damage. Undisturbed expansive soil was considered as a compound of non-damaged part and damaged part. The behavior of the non-damaged part was described using non-linear constitutive model of unsaturated soil. The property of the damaged part was described using a damage evolution equation and two yield surfaces, i.e., loading yield (LY) and shear yield (SY). Furthermore, a consolidation model for unsaturated undisturbed expansive soil was established and a FEM program named UESEPDC was designed. Numerical analysis on solid-liquid-gas tri-phases and multi-field couple problem was conducted for four stages and fields of stress, displacement, pore water pressure, pore air pressure, water content, suction, and the damage region as well as plastic region in an expansive soil slope were obtained.

Coupled Numerical Analysis of the Stability Behaviour of Unsaturated Soil Slopes Under Rainfall Conditions

The stability behaviour of unsaturated soil slopes under rainfall conditions is investigated via a parametric finite element analysis, which is a fully coupled flow and deformation approach linked to a dynamic programming technique for determining the minimum factor of safety as well as its corresponding critical slip surface based on the stress fields from the numerical computation. The effects of rainfall features, soil strength parameters and permeability properties on slope stability are studied. The analyses revealed that the soil matric suction decreased during rainfall, especially in slopes with high permeability and/or with high suction angles of unsaturated soils. The influence of rainfall conditions on such slopes is quite obvious, and soil suction drops rapidly, which leads to a consequent quick reduction in the factor of safety.

Large-Scale Test Model of the Progressive Deformation and Failure of Cracked Soil Slopes

A large-scale test bed(LWH=6 m×3 m×2.8 m)instrumented with various sensors is used to examine the effects of rainfall infiltration and evaporation on the deformation and failure of cracked soil slopes,taking the Anhui area along the Yangtze River as a field example.The results indicate that(1)during rainfall,the soil around the shallow shrinkage fissures attains transient saturation,and the attendant decrease of matric suction is the primary cause of the shallow slope failure;(2)slope deformation continues during post-rainfall evaporation;(3)if a period of evaporation is followed by heavy rainfall,soil creep is concentrated near the deepest cracks,and two zones of steep gradients in pore pressure form at the crest and toe of the slope.Finally,a saturated zone forms near each crack base and gradually enlarges,eventually forming a continuous saturated layer that induces the slope instability or failure.