Experimental Investigation of Multi-Mode Vortex-Induced Vibration of Flexible Risers with Different Mass Ratios

Experiments were conducted on risers with different mass ratios to study the effect of mode conversion and spanwise correlation. The slenderness ratio of the riser model was set as 169, and the Reynolds numbers are 1600-14400. The dynamic responses of riser models versus reduced velocity were analyzed, and the spanwise displacement, frequency,and trajectory of the mode conversion from the lower to the higher mode were explored. The results revealed that the riser model with a higher mass ratio excites a higher number of modes. The conversion region of multi-mode competition exists and narrows with the increasing mass ratio. Mode conversion is continuous and manifests as the transmission of peaks and troughs in mode shape: the peaks and troughs of mode shape move up in the mode stable development region and move down in the mode conversion region. The single-mode dominating vibration exhibits a standing wave feature, and the traveling wave feature is significant in the mode conversion region. Furthermore, the frequency jump is always transmitted from the trough to the peak of the mode shape, and finally, all the axial positions vibrate at the same frequency. The trajectory in the mode conversion region deviates from the 8-shape and recovers the standard8-shape at the middle and late stages of the mode stable development region.

Effect of CaO/SiO_(2) Slag Mass Ratio on Dissolution Rate of Alumina-based Refractory Ceramics

The dissolution of alumina-based refractory ceramics in CaO-Al2O3-SiO_(2)slag melts was performed based on the in-situ observation system of an ultra-high-temperature laser confocal microscope,and the effect of the CaO/SiO_(2)slag mass ratio(C/S ratio)on the dissolution rate of alumina-based refractory ceramics was investigated.The results indicate that the dissolution rate increases with an increase of the C/S ratio and is mainly controlled by diffusion.During the early stage of dissolution,for all C/S ratios,the dissolution process conforms to the classical invariant interface approximation model.During the later stage of dissolution,when the C/S ratio is≥6,the dissolution process is significantly different from the model above because of the formation of a thick interfacial layer,which can be explained by dissolution kinetics.

Determining the Charge-to-Mass Ratio of the Electron

The aim of this lab was to determine an experimental value for the charge-to-mass ratio e/me of the electron. In order to do this, an assembly consisting of Helmholtz coils and a helium-filled fine beam tube containing an electron gun was used. Electrons were accelerated from rest by the electron gun at a voltage of 201.3 V kept constant across trials. When the accelerated electrons collided with the helium atoms in the fine beam tube, the helium atoms entered an excited state and released energy as light. Since the Helmholtz coils put the electrons into centripetal motion, this resulted in a circular beam of light, the radius of which was measured by taking a picture and using photo analysis. This procedure was used to test currents through the Helmholtz coils ranging from 1.3 A to 1.7 A in increments of 0.1 A. Using a linearization of these data, the experimental value for the charge-to-mass ratio of the electron was found to be 1.850 × 1011 C/kg, bounded between 1.440 × 1011 C/kg and 2.465 × 1011 C/kg. This range of values includes the accepted value of 1.759 × 1011 C/kg, and yields a percent error of 5.17%. The rather low percent error is a testament to the accuracy of this procedure. During this experiment, the orientation of the ambient magnetic field due to the Earth at the center of the apparatus was not considered. In the future, it would be worthwhile to repeat this procedure, taking care to position the Helmholtz coils in such a way to negate the effects of the Earth’s magnetic field on the centripetal motion of electrons.

Unified Description of the Three Stable Particles in Self-Action Allows Determination of Their Relative Masses

The Dirac equation γμ(δμ-eAμ)Ψ=mc2Ψ describes the bound states of the electron under the action of external potentials, Aμ. We assumed that the fundamental form of the Dirac equation γμ(δμ-Sμ)Ψ=0 should describe the stable particles (the electron, the proton and the dark-matter-particle (dmp)) bound to themselves under the action of their own potentials Sμ. The new equation reveals that self energy is consequence of self action, it also reveals that the spin angular momentum is consequence of the dynamic structure of the stable particles. The quantitative results are the determination of their relative masses as well as the determination of the electromagnetic coupling constant.

Ratio of Gravitational Force to Electric Force from Empirical Equations in Terms of the Cosmic Microwave Background Temperature

Previously, we presented several empirical equations using the cosmic microwave background (CMB) temperature. Next, we propose an empirical equation for the fine-structure constant. Considering the compatibility among these empirical equations, the CMB temperature (Tc) and gravitational constant (G) were calculated to be 2.726312 K and 6.673778 × 10−11 m3∙kg−1∙s−2, respectively. Every equation could be explained in terms of the Compton length of an electron (λe), the Compton length of a proton (λp) and a. Furthermore, every equation could also be explained in terms of Avogadro’s number and the number of electrons in 1 C. However, the ratio of the gravitational force to the electric force cannot be uniquely determined when the unit of the Planck constant (Js) is changed. In this study, we showed that every equation can be described in terms of Planck constant. From the assumption of minimum mass, the ratio of gravitational force to electric force could be elucidated.

Mass Concentration and Mineralogical Characteristics of Aerosol Particles Collected at Dunhuang During ACE-Asia

Measurements were performed in spring 2001 and 2002 to determine the characteristics of soil dust in the Chinese desert region of Dunhuang, one of the ground sites of the Asia-Pacific Regional Aerosol Characterization Experiment （ACE-Asia）. The mean mass concentrations of total suspended particle matter during the spring of 2001 and 2002 were 317μg m^-3 and 307μg m^-3, respectively. Eleven dust storm events were observed with a mean aerosol concentration of 1095μg m^-3, while the non-dusty days with calm or weak wind speed had a background aerosol loading of 196μg m^-3 on average in the springtime. The main minerals detected in the aerosol samples by X-ray diffraction were illite, kaolinite, chlorite, quartz, feldspar, calcite and dolomite. Gypsum, halite and amphibole were also detected in a few samples. The mineralogical data also show that Asian dust is characterized by a kaolinite to chlorite （K/C） ratio lower than 1 whereas Saharan dust exhibits a K/C ratio larger than 2. Air mass back-trajectory analysis show that three families of pathways are associated with the aerosol particle transport to Dunhuang, but these have similar K/C ratios, which further demonstrates that the mineralogical characteristics of Asian dust are different from African dust.

An online method to determine chlorine stable isotope composition by continuous flow isotope ratio mass spectrometry (CF-IRMS) coupled with a Gasbench Ⅱ

An online method using continuous flow isotope ratio mass spectrometry （CF-IRMS） interfaced with a Gasbench Ⅱ was presented to determine chlorine stable isotope composition. Silver chloride （AgCl） was quantitatively derived from chloride by using silver nitrate （AgNO3）, and then was reacted with iodomethane （CH3Ⅰ） to produce methyl chloride （CH3Cl）. A GasBench Ⅱ equipped with a PoraPlot Q column was used to separate CH3Cl from any other gas species. Finally, chlorine stable isotope analysis was carried out on CH3Cl introduced to the IRMS in a helium stream via an active open split. The minimum amount of Cl used in this method is of the order of 1.4 μmol. Inter-laboratory and inter-technique comparisons show that the total uncertainty incorporating both the precision and accuracy of this method is better than 0.007%. Furthermore, ten seawaters sampled from different locations have a narrow δ37Cl value range from -0.008% to 0.010%, with a mean value of （0.000±0.006）%. This supports the assumption that any seawater can be representative of standard mean ocean chloride （SMOC） and used as an international reference material.

Mass ratio design based on compaction properties of backfill materials

The backfill-mining mass ratio is the ratio of the mass of the backfill materials in the goaf to the mass of the produced raw coal during solid backfill mining and it is regarded as a direct control index of the backfill effect in solid backfill mining. To design the backfill-mining mass ratio in a solid backfill mining panel, the backfill-mining mass ratio was defined on the basis of the basic principle of solid backfill mining. In addition, the density-stress relationship of backfill materials under compaction was obtained for five types of materials to derive a design formula for backfill-mining mass ratio. Moreover, the 6304-1 backfill panel under the large-scale dam of Ji′ning No. 3 coal mine was taken as an engineering case to design the backfill-mining mass ratio. In this way, it is found that the designed backfill-mining mass ratio is 1.22, while the mean value of the measured backfill-mining mass ratio is 1.245. Besides, the maximum roof subsidence is only 340 mm which effectively guarantees the backfill effect in the panel and control of strata movement and surface subsidence.

Female waist-to-hip ratio,body mass index and sexual attractiveness in China

Men and women at Northwest University （n=751）, Xi＇an, China were asked to judge the attractiveness of photographs of female patients who had undergone micrograft surgery to reduce their waist-to-hip ratios （WHR）. Micrograft surgery involves harvesting adipose tissue from the waist and reshaping the buttocks to produce a low WHR and an ‘hourglass＇ female figure. This gynoid distribution of female body fat has been shown to correlate with measures of fertility and health. Significantly larger numbers of subjects, of both sexes, chose post-operative photographs, with lower WHRs, as more attractive than pre-operative photographs of the same women. Some patients had gained, and some had lost weight, post-operatively, with resultant changes in body mass index （BMI）. However, these changes in BMI were not related to judgments of attractiveness. These results show that the hourglass female figure is rated as attractive in China, and that WHR, rather than BMI, plays a crucial role in such attractiveness judgments.

The Influence of Blocking Mass Parameters on the Vibration Isolation Performance of a Power Cabin

Rigid blocking masses are located in the typical base structure of a power cabin based on the impedance mismatch principle.By combining the acoustic-structural coupling method and statistical energy analysis,the full-band vibration and sound radiation reduction effect of vibration isolation masses located in a base structure was researched.The influence of the blocking mass’ cross-section size and shape parameters and the layout location of the base isolation performance was discussed.Furthermore,the effectiveness of rigid vibration isolation design of the base structure was validated.The results show that the medium and high frequency vibration and sound radiation of a power cabin are effectively reduced by a blocking mass.Concerning weight increment and section requirement,suitably increasing the blocking mass size and section height and reducing section width can result in an efficiency-cost ratio.

Numerical simulation of VIV for an elastic cylinder mounted on the spring supports with low mass-ratio

With the development of the offshore deep water oil industry many researchers are focusing on the vortex-induced vibrations （VIV） of deep risers. In the present work, Reynolds-averaged Navier-Stokes （RANS） equations were combined with the SST κ-ω turbulent model to simulate the stream-wise and transverse motion of an elastically mounted cylinder with a low mass-ratio, a natural frequency ratio of fx/fy = 1 and an Re number between 5 300 and 32 000, The four-order Runge-Kutta method was applied to solve the oscillating equation of the cylinder. The relationship between reduced velocity and parameters of the cylinder, including the lift coefficient, the drag coefficient, displacement and the vortex structure were then compared with recent experimental results and discussed in detail. The present numerical simulation reproduced effects have been observed in experiments, such as the lock-in phenomenon, the hysteretic phenomenon and beating behavior.

The Effect of Mass Ratio and Air Damper Characteristics on the Resonant Response of an Air Damped Dynamic Vibration Absorber

In this paper, it is shown that, a road vehicle 2DOF air damped quartercar suspension system can conveniently be transformed into a 2DOF air damped vibrating system representing an air damped dynamic vibration absorber (DVA) with an appropriate change in the ratio μ of the main mass and the absorber mass i.e. when mass ratio μ >> 1. Also the effect of variation of the mass ratio, air damping ratio and air spring rate ratio, on the motion transmissibility at the resonant frequency of the main mass of the DVA has been dis- cussed. It is shown that, as the air damping ratio in the absorber system increases, there is a substantial decrease in the motion transmissibility of the main mass system where the air damper has been modeled as a Maxwell type. Optimal value of the air damping ratio for the minimum motion transmissibility of the main mass of the system has been determined. An experimental setup has been designed and developed with a control system to vary air pressure in the damper in the absorber system. The motion transmissibility characteristics of the main mass system have been obtained, and the optimal value of the air damping ratio has been determined for minimum motion transmissibility of the main mass of the

Optimization of structural parameters for spatial flexible redundant manipulators with maximum ratio of load to mass

Optimization of structural parameters aimed at improving the load carrying capacity of spatial flexible redundant manipulators is presented in this paper. In order to increase the ratio of load to mass of robots, the cross-sectional parameters and constructional parameters are optimized respectively. The cross-sectional and configurational parameters are optimized simultaneously. The numerical simulation of a 4R spatial manipulator is performed. The results show that the load capacity of robots has been greatly improved through the optimization strategies proposed in this paper.

Influences of C/S Mass Ratio and Kieserite Impregnation on Performance of 95-Grade Magnesia Bricks

The irfluences of C/S mass ratio and kieserite im-pregnation on performance of 95-grade magnesia bricks prepared using sintered magnesia DBM95 as main start-ing material, silica fi, me and limestone as additives were researched. The cold and hot physical properties were tested according to Chinese standards on refractories. The hydration resistance was determined in a high pres-sure autoclave with 0. 55 MPa of water vapor pressure for different holding times of 0. 5 h, 3 h, and 5 h. The tri-al results show （ 1 ） adding silica fume to decrease C/S ratio from 0. 84 to 0. 33 improves sintering property; addin,g limestone to increase C/S ratio J？om 0. 84 to 1.95 causes more pores and negatively influences physi-cal properties： BD decreases, AP increases, MOR and CCS decrease generally, but HMOR increases obviously; （2） for non-impregnated specimens, adjusting C/S mass ratio can not improve hydration resistance; （3） the impregnation with kieserite solution can improve hydra-tion resistance of magnesia bricks significantly.

Effect of Mass Ratio on Hydrodynamic Response of a Flexible Cylinder

The effect of the mass ratio on the flow-induced vibration （FIV） of a flexible circular cylinder is experimentally investigated in a towing tank. A Tygon tube with outer and inner diameters of 7.9 mm and 4.8 mm, respectively, was employed for the study. The tube was connected to a carriage and towed from rest to a steady speed up to 1.6 m/s before slowing down to rest again over a distance of 1.6 m in still water. Reynolds number based on the cylinder＇s outer diameter was 800-13,000, and the reduced velocity （velocity normalized by the cylinder＇s natural frequency and outer diameter） spanned from 2 to 25. When connected, the cylinder was elongated from 420 mm to 460 mm under an axial pre-tension of 11 N. Based on the cylinder＇s elongated length, the aspect ratio （ratio of the cylinder＇s length to outer diameter） was calculated as 58. Three mass ratios （ratio of the cylinder＇s structural mass to displaced fluid mass, m＊） of 0.7, 1.0, and 3.4 were determined by filling the cylinder＇s interior with air, water, and alloy powder （nickel-chromium-boron matrix alloy）, respectively. An optical method was adopted for response measurements. Multi-frequency vibrations were observed in both in-line （IL） and cross-flow （CF） responses; at high Reynolds number, vibration modes up to the 3rd one were identified in the CF response. The mode transition was found to occur at a lower reduced velocity for the highest tested mass ratio. The vibration amplitude and frequency were quantified and expressed with respect to the reduced velocity. A significant reduced vibration amplitude was found in the IL response with increasing mass ratios, and only initial and upper branches existed in the IL and CF response amplitudes. The normalized response frequencies were revealed to linearly increase with respect to the reduced velocity, and slopes for linear relations were found to be identical for the three cases tested.

The Mystery behind the Fine Structure Constant Contracted Radius Ratio Divided by the Mass Ratio? A Possible Atomist Interpretation

This paper examines various alternatives for what the fine structure constant might represent. In particular, we look at an alternative where the fine structure constant represents the radius ratio divided by the mass ratio of the electron, versus the proton as newly suggested by Koshy [1], but derived and interpreted here based on Haug atomism (see [2]). This ratio is remarkably close to the fine structure constant, and it is a dimensionless number. We also examine alternatives including the proton mass divided by the Higgs mass, which appears to be another possible candidate for what the fine structure constant might represent.

An Evaluation of Genotoxicity and Cytotoxicity of Melamine in Combination with Cyanuric Acid at Three Mass Ratios

Melamine in combination with cyanuric acid has been considered to be more toxic than either melamine or cyanuric acid alone. The objective of this study was designed to evaluate the combined genotoxicity and cytotoxicity of melamine （M） and cyanuric acid （C） at three mass ratios （1：1, 1：2, 2：1）. MC （1：1）, MC （1：2）, and MC （2：1） were evaluated for their potential genotoxic risk, at gene level by Ames test, and at chromosomal level by micronucleus test. In order to evaluate cytotoxicity in HEK-293 cells, the MTT assay was included. Western blot was also employed to investigate the renal injury molecule-1 （Kim-1） expression in HEK-293 cells exposed to MC. Neither genotoxicity at gene level nor at chromosomal level was observed for MC （1：1）, MC （1：2）, and MC （2：1）. Based on MTT assay, three ratios of MC at 82.5 and 165 μg/mL slightly inhibited viability of HEK-293 cells （P〈0.05）. MC （1：1） at 41.25 and 82.50 IJg/mL could elevate the Kim-1 expression in HEK-293 cells.

Functional composition of tall-statured trees underpins aboveground biomass in tropical forests

The influences of trait diversity(i.e.,the niche complementarity effect)and functional composition(i.e.,the mass ratio effect)on aboveground biomass(AGB)is a highly debated topic in forest ecology.Therefore,further studies are needed to explore these mechanisms in unstudied forest ecosystems to enhance our understanding,and to provide guidelines for specific forest management.Here,we hypothesized that functional composition would drive AGB better than trait diversity and stem size inequality in the(sub-)tropical forests of Nepal.Using data from 101 forest plots,we tested 25 structural equation models(SEMs)to link elevation,stem DBH inequality,trait diversity(i.e.,trait richness,evenness,dispersion and divergence),functional composition[i.e.,community-weighted of maximum height mean(CWM of Hmax),specific leaf area(CWM of SLA),leaf dry matter content(CWM of LDMC),and wood density(CWM of WD)]and AGB.The best-fitted SEMs indicated that CWM of Hmax promoted AGB while overruling the impacts of trait diversity indices on AGB.However,low trait diversity indices were linked with higher AGB while overruling the effects of CWM of SLA,LDMC and WD on AGB.In addition,AGB decreased with increasing elevation,whereas stem size inequality did not influence AGB.Our results suggest that divergent species’functional strategies could shape AGB along an altitudinal gradient in tropical forests.We argue that forest management practices should include plant functional traits in the management plan for the co-benefits of biodiversity conservation and carbon sequestration that underpins human wellbeing.

Mg/Ca,Ba/Ca,and S/Ca ratios as environmental and growth proxies for bivalve shells from the Haima cold seep,South China Sea

Bivalve shell fossils,cemented by authigenic carbonates,are widely spread in the Haima cold seep,Qiongdongnan Basin of the South China Sea(SCS).In this study,we examined an element profile of Gigantidas platifrons in the Haima cold seeps at a water depth of 1381 m.Based on the scanning electron microscope(SEM)analyses,the prismatic layer and nacreous layer were identified,which are characterized by prismatic structure and stratified structure,respectively.In addition,the profile can be subdivided into two parts:altered and unaltered zones.Laser inductively coupled plasma mass spectrometry(LA-ICP-MS)mapping shows that the element concentrations of the altered zones were influenced by the authigenic carbonate rocks,whereas the element concentrations of unaltered zones remain stable.In-situ X-ray diffraction(XRD)analyses show that the mineral constituent of the prismatic layer is mainly composed of aragonite.Along with the growth profile,Mg/Ca ratios of unaltered zones have minor variations,ranging 0.72-0.97 mmol/mol(mean=0.87 mmol/mol),with estimated temperatures of 3.8-4.1℃,indicating that the temperature of the surrounding seawater remains constant and agree with the measured data of 3.9℃which was conducted by a conductivity-temperature-depth system(CTD).The minor variations of Ba/Ca ratios(0.01-0.06 mmol/mol;mean=0.04 mmol/mol)indicate a relatively stabilized salinity of the surrounding seawater.S/Ca ratios show large variations of 0.04-4.15 mmol/mol(mean=1.37 mmol/mol).S/Ca ratios have regular variations which generally correspond to the variations of the Mg/Ca ratios,highlighting that the S/Ca ratios of bivalve shells show the potential to reflect the growth rate of the Gigantides.However,further studies should be carried out on the understanding of the links between the S/Ca ratios and seepage intensity of cold-seep fluids.

一种高效星载功率调节与配电单元设计与实现

文章结合深空探测供配电分系统任务特点,提出功率调节、配电、火工控制等多功能模块轻小型一体化设计的必要性。介绍了国外功率调节与配电单元的研究现状、国产功率调节与配电单元研制的意义,功率调节与配电单元组成及功能设计,并通过多母线融合设计、多路放电均流设计、单元集成化设计等关键技术,解决了深空探测器高可靠轻小型化功率调节与配电单元设计难题。在轨飞行结果表明:功率调节与配电单元功能正常,工作可靠,性能优良。功率调节与配电单元的国产化设计实现,可为其它航天器的设计提供参考和借鉴。