Influences affecting the soil-water characteristic curve

The soil-water characteristic curve (SWCC) is the primary partially saturated soil information as its behavior and properties can be derived from it. Although there have been many studies of unsaturated soils and the SWCC, there is still no combined constitutive model that can simulate soil characteristics accurately. In cases when hydraulic hysteresis is dominant (e.g. under cyclic loading) it is particularly important to use the SWCC. In the past decades, several mathematical expressions have been proposed to model the curve. There are various influences on the SWCC as a source of information, so the curves obtained from conventional tests often cannot be directly applied; and the mathematical expressions from one scenario cannot be used to simulate another situation. The effects of void ratio, initial water content, stress state and high suction were studied in this work revealing that water content and stress state are more important than the other effects; but that the influences tend to decrease when suction increases. The van Genuchten model was modified to simulate better the changes in the degree of saturation at low values of suction. Predictions were compared with experimental results to determine the simulation capability of the model.

Effects of sample dimensions and shapes on measuring soil-water characteristic curves using pressure plate

It is well known that soilewater characteristic curve （SWCC） plays an important role in unsaturated soil mechanics, but the measurement of SWCC is inconvenient. In laboratory it requires days of testing time. For fine-grained clays, it may last for a couple of months using pressure plate tests. In this study, the effects of sample dimensions and shapes on the balance time of measuring SWCCs using pressure plate tests and the shape of SWCCs are investigated. It can be found that the sample dimensions and shapes have apparent influence on the balance time. The testing durations for circular samples with smaller diameters and annular samples with larger contact area are significantly shortened. However, there is little effect of sample dimensions and shapes on the shape of SWCCs. Its mechanism is explored and discussed in details through analysing the principle of pressure plate tests and microstructure of the sample. Based on the above findings, it is found that the circular samples with smaller dimensions can accelerate the testing duration of SWCC using the pressure plate.

Predicting the entire soil-water characteristic curve using measurements within low suction range

The soil-water characteristic curve(SWCC) is widely used in the design and evaluation in the practice of geotechnical and geoenvironmental engineering such as the slope stability under the influence of environmental factors. The SWCC has distinct features in the capillary and adsorption zones due to different physical mechanisms. Measurements of the SWCC are typically limited within the capillary zone(i.e., low suction range). It is cumbersome and time-consuming to measure the SWCC in the adsorption zone(i.e., high suction range). This study presents a simple method to predict the entire SWCC within both the capillary and adsorption zones, using measured data only from low suction range(e.g., from 0 to 500 kPa). Experimental studies were performed on a completely weathered granite residual soil to determine its entire SWCC from saturated to dry conditions. The resultant SWCC, along with the SWCC measurements of 14 soils reported in the literature, were used to validate the proposed method. The results indicate that the proposed method has good consistency with a wide array of measured data used in this study. The proposed method is easy to use as it only requires a simple parameter calibration for a commonly used SWCC model. It can be used to improve the reliability in the prediction of the SWCC over the entire suction range when measurements are limited within the low suction range.

Prediction of loess soil-water characteristic curve by mercury intrusion porosimetry

Mercury intrusion porosimetry(MIP)is a simple and fast way to obtain the pore distribution of soil and can be used to estimate the soil-water characteristic curve(SWCC).In previous studies,soil was assumed to be a perfect wettability material,and the contact angle(CA)of the soil-water interface was taken as zero in the SWCC prediction method.However,the CA has proved to be much greater than zero even for hydrophilic soils according to some soil wettability experiments,and it has a significant effect on predicting the SWCC.In this research,a method for predicting the SWCC by MIP,which takes the CA as a fitting coefficient,is proposed.The pore size distribution curves are measured by MIP,and the SWCCs of two loess soils are measured by pressure plate and filter paper tests.When the CA is taken as70°and 50°for the wetting and drying process,respectively,the SWCCs predicted by the pore size distribution curves agree well with the measured SWCCs.The predicted suction range of the proposed method is 0-105 k Pa.The consistency of the results suggests that utilizing the MIP test to predict the SWCC with a proper CA is effective for loess.

Rapid testing and prediction of soil–water characteristic curve of subgrade soils considering stress state and degree of compaction

The subgrade soil is generally in saturated or unsaturated condition. To analyze complex thermo-hydro-mechanical-chemical (THMC) behaviors of subgrade, it is essential to determine the soil–water characteristic curve (SWCC) that represents the relationship between matric suction and moisture content. In this study, a full-automatic rapid stress-dependent SWCC pressure-plate extractor was developed. Then, the influences of overburden stress and degree of compaction on the SWCC of subgrade soil such as high liquid limit silt (MH) and low liquid limit clay (CL) were analyzed. Accordingly, a new model taking into account the influences of overburden stress and degree of compaction based on the well-known Van Genuchten (VG) SWCC fitting model was presented and validated. The results show that with the increase of the degree of compaction and overburden stress, the saturated moisture content of subgrade soil decreases, while the air-entry value increases and the transition section curve becomes flat. The influences of the degree of compaction and overburden stress on the SWCC of MH is greater than that of CL. Meanwhile, there was a satisfactory agreement between the prediction and measurement, indicating a good performance of the new model for predicting the SWCC.

Water infiltration and soil-water characteristics of compacted loess under applied vertical stress

Additional stress formed by postconstruction buildings in loess-filling areas affects water infiltration in soil and causes soil deformation.To investigate this effect,under constant water head,vertical infiltration tests on compacted loess with two initial dry densities for different applied vertical stresses were developed using vertical stresscontrollable one-dimensional soil columns.The timehistory curves of vertical deformation,wetting front depth,cumulative infiltration depth,volumetric water content(VWC)and suction were measured,and the soil-water characteristic curves(SWCCs)were determined.The results showed that:(1)the infiltration ability of the soil column weakens with increasing applied vertical stress and initial dry density;(2)vertical deformation increases rapidly at first and then tends to be stable slowly at the consolidation and wetting-induced deformation stage,and is positively correlated with applied vertical stress and is negatively correlated with initial dry density.The stability time of wetting-induced deformation and the corresponding wetting front depth increase with the increase of applied vertical stress,while they decrease obviously when initial dry density increases;(3)the influence of applied vertical stress on soilwater characteristics in soil columns with various initial dry densities is related to the deformation depth of soil column.The VG(Van Genuchten)model is suitable for fitting the SWCCs at different monitoring positions.A normalized SWCC model introducing the applied vertical stress was proposed for each initial dry density using the mathematical relationship between the fitting parameters and the applied vertical stress.

Soil freezing process and different expressions for the soil-freezing characteristic curve

The soil-freezing characteristic curve(SFCC),which represents the relationship between unfrozen water content and subfreezing temperature(or suction at ice-water interface)in a freezing soil,can be used for understanding the transportation of heat,water,and solute in frozen soils.In this paper,the soil freezing process and the similarity between the SFCC of saturated frozen soil and soil-water characteristic curve(SWCC)of unfrozen unsaturated soil are reviewed.Based on similar characteristics between SWCC and SFCC,a conceptual SFCC is drawn for illustrating the main features of soil freezing and thawing processes.Various SFCC expressions from the literature are summarized.Four widely used expressions(i.e.,power relationship,exponential relationship,van Genuchten 1980 equation and Fredlund and Xing 1994 equation)are evaluated using published experimental data on four different soils(i.e.,sandy loam,silt,clay,and saline silt).Results show that the exponential relationship and van Genuchten(1980)equation are more suitable for sandy soils.The simple power relationship can be used to reasonably best-fit the SFCC for soils with different particle sizes;however,it exhibits limitations when fitting the saline silt data.The Fredlund and Xing(1994)equation is suitable for fitting the SFCCs for all soils studied in this paper.

Soil-water characteristics and shear strength in constant water content triaxial tests on Yunnan red clay

The shear strength parameters for geotechnical designs are obtained mainly from consolidated drained （CD） or consolidated undrained （CU） triaxial tests. However, during construction, the excess pore-air pressure generally dissipates instantaneously while the excess pore-water pressure dissipates with time. This condition needs to be simulated in a constant water content （CW） triaxial test. The study on Yunnan red clay is carried out to investigate the soil-water characteristics and the shear strength characteristics under the constant water content condition. Osmotic technique is used to obtain the soil-water characteristic curve. A series of CW triaxial tests are conducted on statically compacted specimens. The experimental results show that the soil-water characteristic curve has a low air entry value of 7 kPa due to large pores in non-uniform pore size distribution, and a high residual value exceeding 10 MPa. In addition, the initial degree of saturation and net confining stress play an important role in affecting the shear characteristics under the constant water content condition. Finally, a new semi-empirical shear strength model in terms of degree of saturation is proposed and then applied to Yuunan red clay. Simulation result shows that the model is capable of capturing some key features of soils. The model can be used in whole engineering practice range, covering both unsaturmed and saturated soils.

Factors Influencing the Soil-Water Characteristics of Unsaturated Tropical Silty Sand

Fine grain soils have a complex engineering behaviour which depends but not limited to moisture content, changes in external pressure and characteristics of the pore medium. Sand often contains a considerable percent of silt which is expected to alter its natural behaviour. This composite matrix is referred to as silty-sand. To understand the behaviour of this matrix under varying moisture conditions, some of the factors influencing the soil-water characteristics of unsaturated silty sands were investigated. Representative samples were collected from a river bank after its index properties were predetermined in the laboratory. The samples were compacted at different moisture conditions and compactive efforts. With the pressure plate extractor device, the Soil-Water Characteristic (SWC) was obtained and SWC Curves plotted. Compaction at greater compactive effort (modified proctor) and optimum moisture content produced the largest air entry value and reduced air voids. The air entry values of the soils obtained ranged from 21 kPa to 57 kPa. Also changes in the shape of the SWCC were consistent with changes in pore size which occur by varying compaction conditions. Result shows that soil structure, compaction water content, compactive effort and percentage of fine particles are factors affecting the Soil-Water Characteristics.

Soil−water characteristics of weathered crust elution-deposited rare earth ores

The permeability of the weathered crust elution-deposited rare earth ores directly affects the efficiency of in-situ leaching.The soil−water characteristic curve(SWCC)is an important constitutive relation for calculating the permeability of ore body,which is related to many factors.Soil−water characteristic tests of rare earth ore samples considering different factors were carried out by using the pressure plate instrument.Effects of dry density,particle size and solution leaching on water holding behavior and the mechanism were investigated.The experimental observations indicate that with the decrease of dry density,the pore ratio increases gradually,and the saturated water content increases.Under the same matric suction,the water content decreases gradually with the increase of particle size,thus decreasing water holding capacity of ore accordingly.In the same water content,matric suction is inversely proportional to particle size.Under the same matric suction,the water content of ore samples after leaching is less than that of the ore samples before leaching,indicating that solution leaching can decrease water holding capacity of ore.

Effect of the uncertainty in soil-water characteristic curve on the estimated shear strength of unsaturated soil

Most failures or instabilities of geotechnical structures commonly result from shear failure in soil. In addition, many infrastructures are constructed within the unsaturated zone. Therefore, the determination of shear strength of unsaturated soil is crucial in geotechnical design. The soil-water characteristic curve(SWCC) is commonly used to estimate the shear strength of unsaturated soil because the direct measurement is time-consuming and costly. However, the uncertainty associated with the determined SWCC is rarely considered in the estimation of the shear strength. In this paper, the uncertainties of SWCC resulted from different factors are reviewed and discussed. The variability of the estimated shear strength for the unsaturated soil due to the uncertainty of SWCC associated with the best fit process is quantified by using the upper and lower bounds of the determined SWCC. On the other hand, the uncertainties of the estimated shear strength due to different initial void ratios or different confining pressures are quantified by adopting different SWCCs. As a result, it is recommended that the measured SWCC from the conventional Tempe cell or pressure plate needs to be corrected by considering different stress levels in the estimation of the shear strength of unsaturated soil.

Effect of initial gravimetric water content and cyclic wetting-drying on soil-water characteristic curves of disintegrated carbonaceous mudstone

The soil-water characteristic curve(SWCC)is often used to estimate unsaturated soil properties(e.g.strength,permeability,volume change,solute and thermal diffusivity).The SWCC of soil samples is significantly affected by cyclic wetting-drying.To examine how water content and cyclic wetting-drying affect the SWCC of disintegrated carbonaceous mudstone(DCM),SWCC tests were implemented using a pressure-plate apparatus.In addition,SWCC models for DCM considering the initial gravimetric water content and cyclic wetting-drying were developed.The test results showed that the volumetric water content(θ)of the DCM first decreased rapidly and then became stable as matric suction(s)increased.The initial water content affected the SWCC by altering the pore structure of the DCM.For a given number of wetting-drying cycles,the higher the initial water content,the higher the stabilizedθ.At a given s value,θdecreased as the number of wetting-drying cycles increased,which suggests that cyclic wetting-drying reduces the water-holding capacity of DCM.The Gardner model for DCM was constructed considering initial water content and cyclic wetting-drying,and was effective at describing and predicting the SWCC model for DCM.

Soil-Water Charateristics of Tropical Clay Soil under High and Low Suction Conditions

Tropical clay soil was compacted at different moisture conditions (dry, wet and optimum) and compactive efforts (Reduced proctor, Standard proctor, West African standard and Modified proctor). Experimental Soil-Water Characteristics (SWC) of the soil was derived using the pressure plate extractor equipment and SWC Curves (SWCC) plotted as gravimetric water content versus logarithm of matric suction. The Air Entry Values (A.E.V) obtained from experimental work ranged from 21 kPa to 59 kPa and compared favourably well with those estimated from predictive models with values of 23 kPa to 52 kPa. Specimens compacted with greater compactive effort (Modified proctor) and at optimum moisture content produced the largest air entry value of 59 kPa and reduced air voids. Changes observed in the shape of the SWCC were consistent with changes in pore size which occurred by varying compaction conditions. The shape of the soil-water characteristics curve was found to depend on the soil structure, compactive water content and compactive effort and not solely on the percentage of fine particles.

基于核磁共振及分形理论预测非饱和土石混合体SWCC

【目的】土石混合体的物理力学特性与土—水特征曲线(SWCC)关系紧密,直接或间接测量SWCC费时耗力,且所得结果具有离散性,因此建立预测非饱和土石混合体SWCC的理论模型具有现实意义。【方法】采用NMR技术反演得到横向弛豫时间T_(2)图谱,将之转化为累计孔隙体积曲线,从而结合Young-Laplace′s理论及分形理论,以T_(2)为纽带建立起体积含水率与基质吸力的理论模型,并对模型进行验证。【结果】结果显示:土石混合体具有多重分形特征,对其进行分区研究,可由体积含水率与基质吸力在双对数坐标中的斜率换算得出不同孔隙半径范围内的分形维数;体积含水率与基质吸力的对数值存在强烈的线性关系,其相关系数均≥0.995;初始含水率与模型中的拟合参数具有线性关系,且相关系数均≥0.990,模型中的参数均可通过初始含水率进行求解。【结论】结果表明:模型预测结果与实测SWCC吻合程度较高,可以很好地应用于非饱和土石混合体的SWCC预测中。

长春地区非饱和粉质黏土的土-水特征试验研究

土-水特征曲线(SWCC)是反映非饱和土工程特性的重要表现形式。为研究长春地区非饱和土的土-水特征曲线变化,以长春地区广泛分布的粉质黏土作为研究对象,采用GEO-Experts压力板仪和GDS非饱和土三轴仪对不同初始含水率的土体进行土-水特征曲线的测量分析。结果表明:不同设备所测得的结果基本一致,土体的进气值均在基质吸力25 kPa左右时达到。土体的体积含水率均随基质吸力的增加而减小,土-水特征曲线均在基质吸力为125 kPa时出现明显拐点。同一含水率土样,GEO-Experts压力板仪的排水体积比GDS非饱和土三轴仪多,压力板仪所对应的体积含水率相对较低。

土水特征曲线(SWCC)的滞回特性模拟研究

为了模拟非饱和土的水力、力学特性在多次降雨、蒸发过程中的变化特性,本文以传统域模型的基本原理为基础,推到得到了一个能够模拟SWCC滞后性的计算模型,该模型计算方法简单,易于通过程序实现,且通过与试验数据和其他模型的计算结果对比,验证了该模型的合理性,同时,这个模型可为研究在复杂吸力变化状态下非饱和土的渗流特性、强度特性以及本构模型的研究打下一定的基础。

非饱和土土水特征曲线(SWCC)测试与预测

非饱和土土水特征曲线(SWCC)表示了土中含水量与吸力之间的关系。文章介绍了6种常用方法,各有其适用范围。体积压力板仪可量测最大基质吸力值为1500kPa的干燥曲线和浸湿曲线;超过1500kPa时,可用盐溶液法进行量测;Tem-ple仪可量测基质吸力达100kPa的干燥曲线;滤纸法可用于测量土体的基质吸力与总吸力;Dew-point电位计可用于量测土样总吸力变化,尤其适合渗透吸力的量测;TDR探头适合于量测小于300kPa的基质吸力。用GDS非饱和土三轴仪可以进行SWCC测试,测试范围主要取决于陶土板的进气值。用准确的数学模型对测得的含水量、吸力数据进行拟合,对于预测非饱和土力学性质、渗透系数、抗剪强度及分析边坡稳定性有重要意义。由于准确测试SWCC难度较大,并且测试影响因素较多,所以根据土体孔隙大小分布和颗粒大小分布情况预测SWCC,也是一种较好的方法。

考虑尿素浓度对SWCC影响的VG模型

利用Tempe压力膜仪,进行了不同浓度尿素溶液的土-水特征曲线(SWCC)试验,得出了不同SWCC的Van Genuchten(VG)拟合模型。结合各VG模型,采用线性回归分析,确定了模型中各参数与尿素浓度的关系,进而建立了能够考虑尿素浓度影响的VG模型。所得模型中各参数拟合相关度均较高。由所建模型可知,尿素浓度对参数α影响较小,而对参数n影响较大;浓度越大,参数α越小,而参数n越大。所得结果弥补了其他方法不能考虑尿素浓度对SWCC的影响,对补充和发展SWCC试验和理论具有一定的意义。所建SWCC模型未考虑尿素浓度对溶质吸力的影响,也未开展尿素溶液对土体SWCC影响机理研究;这两方面有待以后的工作进一步研究。

Unraveling the hydraulic properties of loess for landslide prediction:A study on variations in loess landslides in Lanzhou,Dingxi,and Tianshui,China

Loess has distinctive characteristics,leading to frequent landslide disasters and posing serious threats to the lives and properties of local re sidents.The involvement of water repre sents a critical factor in inducing loess landslides.This study focuses on three neighboring cities sequentially situated on the Loess Plateau along the direction of aeolian deposition of loess,namely Lanzhou,Dingxi,and Tianshui,which are densely populated and prone to landslide disasters.The variations in hydraulic properties,including water retention capacity and permeability,are investigated through Soil Water Characteristic Curve(SWCC)test and hydraulic conductivity test.The experimental findings revealed that Tianshui loess exhibited the highest water retention capacity,followed by Dingxi loess,while Lanzhou loess demonstrated the lowest water retention capacity.Contrastingly,the results for the saturated permeability coefficient were found to be the opposite:Tianshui loess showed the lowest permeability,whereas Lanzhou loess displayed the highest permeability.These results are supported and analyzed by scanning electron microscopy(SEM)observation.In addition,the water retention capacity is mathematically expressed using the van Genuchten model and extended to predict unsaturated hydraulic properties of loess.The experimental results exhibit a strong accordance with one another and align with the regional distribution patterns of disasters.

非饱和重塑黄土SWCC试验与拟合研究

利用GCTS土-水特征曲线仪研究了颗粒级配对非饱和重塑黄土土-水特性的影响;通过Brooks&Corey、Van Genuchten、Gardner、Fredlund&Xing(3参数模型)、Fredlund&Xing(4参数模型)五种常用模型对试验数据进行了拟合分析,得到适合非饱和重塑黄土的SWCC(soil-water characteristic curve)数学模型;通过提出“滞回比”这一参数,初步研究了颗粒级配对土-水特征曲线滞回特性的影响;利用Gardner经验模型、Van Genuchten统计传导模型对非饱和重塑黄土试样的渗透系数进行了拟合分析。结果表明:Gardner和Van Genuchten模型对非饱和重塑黄土土-水特征曲线拟合效果最好,a值随颗粒粒径的增大而减小,n值随颗粒粒径的增大而增大,滞回比随着颗粒粒径的增大逐渐减小;非饱和重塑黄土试样渗透系数随基质吸力的变化而变化,同一种模型对渗透系数的预测在增减湿过程中渗透系数数值存在差别。