Anatase TiO2 films were successfully prepared on foam nickel substrates by sol-gel technique using tetrabutyl titanate as precursor. The characteristics of the TiO2 films were investigated by XPS, XRD, FE-SEM, TEM and...Anatase TiO2 films were successfully prepared on foam nickel substrates by sol-gel technique using tetrabutyl titanate as precursor. The characteristics of the TiO2 films were investigated by XPS, XRD, FE-SEM, TEM and UV-Vis absorption spectra. The photocatalytic activities of TiO2 films were investigated by photocatalytic degradation reactions of gaseous acetaldehyde, an indoor pollutant, under ultraviolet light irradiation. It was found that Ni^2＋ doping into TiO2 films due to the foam nickel substrates resulted in the extension of absorption edges of TiO2 films from UV region to visible light region. The pre-heating for foam nickel substrates resulted in the formation of NiO layer, which prevented effectively the injection of photogenerated electrons from TiO2 films to metal nickel. The TiO2 films displayed high photocatalytic activity for the degradation of acetaldehyde, and were enhanced by calcining the substrates and coating TiO2 films repeatedly. The high activity was mainly attributed to the improvement of the characteristics of substrate surface and the increase of active sites on photocatalyst.展开更多
Pb-doped TiO2 photocatalytic thin films were prepared on a soda-lime glass substrate via sol-gel method using TiO2 sol solution containing lead and characterized by X-ray photoelectron spectroscopy (XPS). The results ...Pb-doped TiO2 photocatalytic thin films were prepared on a soda-lime glass substrate via sol-gel method using TiO2 sol solution containing lead and characterized by X-ray photoelectron spectroscopy (XPS). The results showed that besides oxides of Ti(IV) there is a certain amount of oxides of To(?) and Ti(?) and Pb exists in the forms of PbTiO3 and PbO. The photocatalytic activity of the Pb-doped TiO2 films was evaluated by the photocatalytic decolorization of aqueous methyl orange and photocatalytic mechanism mas also analyzed.展开更多
TiO2-SiO2 thin films have been prepared on slide glass substrates by sol-gel method, and the effect of SiO2 additive on photo-generated hydrophilicity of TiO2 thin film was investigated by measuring the contact angle ...TiO2-SiO2 thin films have been prepared on slide glass substrates by sol-gel method, and the effect of SiO2 additive on photo-generated hydrophilicity of TiO2 thin film was investigated by measuring the contact angle of water, the microstructure, the transmittance, the photocatalytic activity and the specific surface area . The results showed that 10mol% of SiO2 additive was the most effective for decreasing contact angle of water. The SiO2 additive of less than 30mol% has a suppressive effect on the crystal growth of anatase in calcinations, resulting in a large surface area. Consequently, the super-hydrophilicity was improved.展开更多
Porous TiO2 thin films were prepared from alkoxide solutions with and without polyethylene glycol (PEG) by sol-get route on soda lime glass, and were characterized by atomic force microscopy (AFM), transmission electr...Porous TiO2 thin films were prepared from alkoxide solutions with and without polyethylene glycol (PEG) by sol-get route on soda lime glass, and were characterized by atomic force microscopy (AFM), transmission electron microscopy (TEM) and X-ray diffraction (XRD). The results show that TiO2 film prepared from precursor solution without PEG is composed of spherical particles of about 100 nm and several nanometer mesoporous pores. With the increase of the amount of PEG added to the precursor solution, the diameter and the depth of the pores in the resultant films increas on the decomposition of PEG during heat-treatment, which lead to them increase of the surface roughness of the films. XRD and TEM results show that the single anatase phase is precipitated and there are some orientation effects in (101) direction.展开更多
Titanium dioxide (TiO_2) thin films were prepared on microscopes slides by sol-gel and dip-coating processes from specially formulated sols.The results show that there exists anatase and rutile structure of TiO_2 when...Titanium dioxide (TiO_2) thin films were prepared on microscopes slides by sol-gel and dip-coating processes from specially formulated sols.The results show that there exists anatase and rutile structure of TiO_2 when heat treatment temperature is 450℃,and at 800℃,TiO_2 particle size is of below 100 nm and rutile structure is presented.In the range of 360 nm～400 nm the transmittance of TiO_2 sol increases with the increasing of the concentration of Ti(OC_4H_9)_4 in ethanol solution. The transmittance of TiO_2 films with various number of the layer is measured to be 0% below 320 nm,and the three-layer TiO_2 film is of the best UV resistance in the range of 320 nm～400 nm.展开更多
The transparent anatase TiO 2 nanometer thin films were prepared by the sol-gel method on soda-lime glass.X-ray diffraction,thermal analysis and UV-visible spectrophotometer were used to analyze the formation of the ...The transparent anatase TiO 2 nanometer thin films were prepared by the sol-gel method on soda-lime glass.X-ray diffraction,thermal analysis and UV-visible spectrophotometer were used to analyze the formation of the phases.Only increasing the heat-treatment time,the average grain size has no obvious change.The mechanism of grain growth in TiO 2 thin film is probably as follows:the grain of coating will become grain core later;TiO 2 sol constantly deposited on the surface of TiO 2 grain and formed membrane with increasing of coating cycle times;TiO 2 grain in the film grow steadily.展开更多
Gold nanoparticles dispersed Y2O3 films were prepared through a sol-gel method by using yttrium acetate and Au nanoparticles colloid as precursors. The films were characterized by X-ray diffraction （XRD）, transmissi...Gold nanoparticles dispersed Y2O3 films were prepared through a sol-gel method by using yttrium acetate and Au nanoparticles colloid as precursors. The films were characterized by X-ray diffraction （XRD）, transmission electron microscopy （TEM） and UV-VIS absorption spectra. XRD patterns and TEM images of Y2O3 ＋ Au films give the same resuits on structure and particle size as that of pure Y2O3 films. The surface plasma resonance （SPR） of Au nanoparticles in Y2O3 ＋ Au film was observed around 550 nm in the absorption spectrum and its position shifts to red with increasing annealing temperature is caused by the increase of dielectric constant of Y2O3 matrix and the size of Au nanoparticles. The second and third order nonlinear optical effects of Y2O3 ＋ Au films were also observed. The photoluminescent properties of Y2O3 ： Eu ＋ Au films were investigated and results indicate that there exist an energy transfer from Eu^3 ＋ to Au nanoparticles and this energy transfer decreases the emission of Eu^3 ＋ in Y2O3 ： Eu ＋ Au film.展开更多
In this study, vanadium doped TiO2 thin films were deposited on glass substrates using a sol-gel dip-coating process. X-Ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR) and UV-Vis spectrophotomete...In this study, vanadium doped TiO2 thin films were deposited on glass substrates using a sol-gel dip-coating process. X-Ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR) and UV-Vis spectrophotometer were used to characterize the structural, chemical and the optical properties of the thin films. The photo-catalytic activities of films were investigated by methylene blue degradation. Water contact angle on the film surfaces was measured by a water contact angle analyzer. The results indicated that vanadium doping had a significant effect on the self-cleaning properties of TiO2 thin films.展开更多
The Ag-TiO2 thin film has been prepared on glass substrate by sol-gel process . The structure and properties of the materials were studied by DTA , XRD, and EPR. The photocatalytic activity was examined by the photoca...The Ag-TiO2 thin film has been prepared on glass substrate by sol-gel process . The structure and properties of the materials were studied by DTA , XRD, and EPR. The photocatalytic activity was examined by the photocatalytic degradation of dichlorophos. The analysis results indicate that the photocatalytic activity of the Ag-TiO2 thin film is higher than that of pure TiO2 thin film. It is also influenced by the content of anatase and heating temperature . The ESR result shows that the Ag-TiO2 thin film has more hydroxide radicals than pure TiO2 thin film after illuminated by UV light.展开更多
Pure TiO2 thin films and iron doped TiO2 thin films on glass substrate were prepared by sol-gel method, and characterized by X-ray diffractometer （XRD）, thermo-gravimetric analysis （TG-DSC）, high resolution transm...Pure TiO2 thin films and iron doped TiO2 thin films on glass substrate were prepared by sol-gel method, and characterized by X-ray diffractometer （XRD）, thermo-gravimetric analysis （TG-DSC）, high resolution transmission electron microscope （HRTEM）, scanning electron microscope （SEM） and UV-Vis spectroscopy, respectively. The experimental results show that the pure TiO2 thin films and iron doped TiO2 thin films can destroy most of the escherichia coli and bacillus subtillis under the irradiation of 365 nm UV-light. However, the iron doped TiO2 thin film is a better photocatalyst than pure TiO2 thin film. The ultrastructural studies provide direct evidences for understanding the bactericidal mechanism of the TiO2 photocatalyst.展开更多
We prepare CuGaO2 thin films on SiO2 substrates by using the sol-gel spin-coating method with two combinations of Cu and a Ga source, Cu and Ga nitrate, or acetylacetonate. X-ray diffraction analysis reveals that the ...We prepare CuGaO2 thin films on SiO2 substrates by using the sol-gel spin-coating method with two combinations of Cu and a Ga source, Cu and Ga nitrate, or acetylacetonate. X-ray diffraction analysis reveals that the thin films prepared using nitrate sol that are annealed at a temperature of 850°C - 950°C show both c-axis-orientated peaks, (006) and a non-c-axis-oriented peak (012) with similar intensity;little dependence of signal intensity on annealing temperature is also shown. The films are opaque in appearance at these annealing temperatures. Scanning electron microscope observation reveals that the opaque appearance is due to the texture or cracks on the surface of the films. In contrast, the films prepared using acetylacetonate show a (006) peak with higher signal intensity than the (012) peaks. The films show more transparent appearance than that of the films by nitrate. The highest conductivity of the film is 5.7 × 10-4Ω-1·cm-1, obtained in the films by nitrate annealed at 850°C.展开更多
Delafossite structured p-type wide bandgap semiconductor, CuYO<sub>2</sub> thin films were prepared on SiO<sub>2</sub> substrate by sol-gel method using copper (II) acetate and yttrium (III) ac...Delafossite structured p-type wide bandgap semiconductor, CuYO<sub>2</sub> thin films were prepared on SiO<sub>2</sub> substrate by sol-gel method using copper (II) acetate and yttrium (III) acetate as source materials. The films preparation process was studied by varying annealing temperature after the preparation of gel films by spin coating, followed by thermal annealing at higher temperature. In the present work, one step annealing directly from Cu-Y-gel under nitrogen flow was used. X-ray diffraction (XRD) revealed that the film annealed at 800<sup>。</sup>C is significantly c-axis oriented, shows only (002) and (004) peaks at 15.6<sup>。</sup> and 31.5<sup>。</sup>, respectively. The optical bandgap of 3.7 - 3.8 eV is estimated by (αhν)2 plot which is higher than previous works. In addition, the films with highly c-axis orientation showed photoluminescence (PL) at room temperature with very broad peak at 2.3 eV. The films annealed at different temperature showed different structural properties.展开更多
基金Project supported by the Special Foundation of Nanometer Technology from Shanghai Municipal Science and Technology Commis-sion(STCSM) (No. 0552nm002).
文摘Anatase TiO2 films were successfully prepared on foam nickel substrates by sol-gel technique using tetrabutyl titanate as precursor. The characteristics of the TiO2 films were investigated by XPS, XRD, FE-SEM, TEM and UV-Vis absorption spectra. The photocatalytic activities of TiO2 films were investigated by photocatalytic degradation reactions of gaseous acetaldehyde, an indoor pollutant, under ultraviolet light irradiation. It was found that Ni^2＋ doping into TiO2 films due to the foam nickel substrates resulted in the extension of absorption edges of TiO2 films from UV region to visible light region. The pre-heating for foam nickel substrates resulted in the formation of NiO layer, which prevented effectively the injection of photogenerated electrons from TiO2 films to metal nickel. The TiO2 films displayed high photocatalytic activity for the degradation of acetaldehyde, and were enhanced by calcining the substrates and coating TiO2 films repeatedly. The high activity was mainly attributed to the improvement of the characteristics of substrate surface and the increase of active sites on photocatalyst.
基金Natural Science Foundation of Hubei Province, China (No. 98J029)
文摘Pb-doped TiO2 photocatalytic thin films were prepared on a soda-lime glass substrate via sol-gel method using TiO2 sol solution containing lead and characterized by X-ray photoelectron spectroscopy (XPS). The results showed that besides oxides of Ti(IV) there is a certain amount of oxides of To(?) and Ti(?) and Pb exists in the forms of PbTiO3 and PbO. The photocatalytic activity of the Pb-doped TiO2 films was evaluated by the photocatalytic decolorization of aqueous methyl orange and photocatalytic mechanism mas also analyzed.
基金Funded by Key Scientific and Technological Items of the Ministry of Education (No.99087) .
文摘TiO2-SiO2 thin films have been prepared on slide glass substrates by sol-gel method, and the effect of SiO2 additive on photo-generated hydrophilicity of TiO2 thin film was investigated by measuring the contact angle of water, the microstructure, the transmittance, the photocatalytic activity and the specific surface area . The results showed that 10mol% of SiO2 additive was the most effective for decreasing contact angle of water. The SiO2 additive of less than 30mol% has a suppressive effect on the crystal growth of anatase in calcinations, resulting in a large surface area. Consequently, the super-hydrophilicity was improved.
基金This work was supported by the National Natural Science Foundation of China(No.50081001)the Education Department Project of Liaoning Province(No.202073425).
基金The work was partially supported by a grant from the National Natural Science Foundation of China and the ResearchGrants Counc
文摘Porous TiO2 thin films were prepared from alkoxide solutions with and without polyethylene glycol (PEG) by sol-get route on soda lime glass, and were characterized by atomic force microscopy (AFM), transmission electron microscopy (TEM) and X-ray diffraction (XRD). The results show that TiO2 film prepared from precursor solution without PEG is composed of spherical particles of about 100 nm and several nanometer mesoporous pores. With the increase of the amount of PEG added to the precursor solution, the diameter and the depth of the pores in the resultant films increas on the decomposition of PEG during heat-treatment, which lead to them increase of the surface roughness of the films. XRD and TEM results show that the single anatase phase is precipitated and there are some orientation effects in (101) direction.
文摘Titanium dioxide (TiO_2) thin films were prepared on microscopes slides by sol-gel and dip-coating processes from specially formulated sols.The results show that there exists anatase and rutile structure of TiO_2 when heat treatment temperature is 450℃,and at 800℃,TiO_2 particle size is of below 100 nm and rutile structure is presented.In the range of 360 nm～400 nm the transmittance of TiO_2 sol increases with the increasing of the concentration of Ti(OC_4H_9)_4 in ethanol solution. The transmittance of TiO_2 films with various number of the layer is measured to be 0% below 320 nm,and the three-layer TiO_2 film is of the best UV resistance in the range of 320 nm～400 nm.
文摘The transparent anatase TiO 2 nanometer thin films were prepared by the sol-gel method on soda-lime glass.X-ray diffraction,thermal analysis and UV-visible spectrophotometer were used to analyze the formation of the phases.Only increasing the heat-treatment time,the average grain size has no obvious change.The mechanism of grain growth in TiO 2 thin film is probably as follows:the grain of coating will become grain core later;TiO 2 sol constantly deposited on the surface of TiO 2 grain and formed membrane with increasing of coating cycle times;TiO 2 grain in the film grow steadily.
文摘Gold nanoparticles dispersed Y2O3 films were prepared through a sol-gel method by using yttrium acetate and Au nanoparticles colloid as precursors. The films were characterized by X-ray diffraction （XRD）, transmission electron microscopy （TEM） and UV-VIS absorption spectra. XRD patterns and TEM images of Y2O3 ＋ Au films give the same resuits on structure and particle size as that of pure Y2O3 films. The surface plasma resonance （SPR） of Au nanoparticles in Y2O3 ＋ Au film was observed around 550 nm in the absorption spectrum and its position shifts to red with increasing annealing temperature is caused by the increase of dielectric constant of Y2O3 matrix and the size of Au nanoparticles. The second and third order nonlinear optical effects of Y2O3 ＋ Au films were also observed. The photoluminescent properties of Y2O3 ： Eu ＋ Au films were investigated and results indicate that there exist an energy transfer from Eu^3 ＋ to Au nanoparticles and this energy transfer decreases the emission of Eu^3 ＋ in Y2O3 ： Eu ＋ Au film.
文摘In this study, vanadium doped TiO2 thin films were deposited on glass substrates using a sol-gel dip-coating process. X-Ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR) and UV-Vis spectrophotometer were used to characterize the structural, chemical and the optical properties of the thin films. The photo-catalytic activities of films were investigated by methylene blue degradation. Water contact angle on the film surfaces was measured by a water contact angle analyzer. The results indicated that vanadium doping had a significant effect on the self-cleaning properties of TiO2 thin films.
基金Funded by the National Natural Science Foundation of Chi-na(Project 5007216) and Technology Foundation of Ministry of Edu-cation in China (Project 9908)
文摘The Ag-TiO2 thin film has been prepared on glass substrate by sol-gel process . The structure and properties of the materials were studied by DTA , XRD, and EPR. The photocatalytic activity was examined by the photocatalytic degradation of dichlorophos. The analysis results indicate that the photocatalytic activity of the Ag-TiO2 thin film is higher than that of pure TiO2 thin film. It is also influenced by the content of anatase and heating temperature . The ESR result shows that the Ag-TiO2 thin film has more hydroxide radicals than pure TiO2 thin film after illuminated by UV light.
基金the National"973"Plan Research Project(No.2004CB619204)Educational Ministry Scientific and Technological Research Key Project(No.02052)
文摘Pure TiO2 thin films and iron doped TiO2 thin films on glass substrate were prepared by sol-gel method, and characterized by X-ray diffractometer （XRD）, thermo-gravimetric analysis （TG-DSC）, high resolution transmission electron microscope （HRTEM）, scanning electron microscope （SEM） and UV-Vis spectroscopy, respectively. The experimental results show that the pure TiO2 thin films and iron doped TiO2 thin films can destroy most of the escherichia coli and bacillus subtillis under the irradiation of 365 nm UV-light. However, the iron doped TiO2 thin film is a better photocatalyst than pure TiO2 thin film. The ultrastructural studies provide direct evidences for understanding the bactericidal mechanism of the TiO2 photocatalyst.
文摘We prepare CuGaO2 thin films on SiO2 substrates by using the sol-gel spin-coating method with two combinations of Cu and a Ga source, Cu and Ga nitrate, or acetylacetonate. X-ray diffraction analysis reveals that the thin films prepared using nitrate sol that are annealed at a temperature of 850°C - 950°C show both c-axis-orientated peaks, (006) and a non-c-axis-oriented peak (012) with similar intensity;little dependence of signal intensity on annealing temperature is also shown. The films are opaque in appearance at these annealing temperatures. Scanning electron microscope observation reveals that the opaque appearance is due to the texture or cracks on the surface of the films. In contrast, the films prepared using acetylacetonate show a (006) peak with higher signal intensity than the (012) peaks. The films show more transparent appearance than that of the films by nitrate. The highest conductivity of the film is 5.7 × 10-4Ω-1·cm-1, obtained in the films by nitrate annealed at 850°C.
文摘Delafossite structured p-type wide bandgap semiconductor, CuYO<sub>2</sub> thin films were prepared on SiO<sub>2</sub> substrate by sol-gel method using copper (II) acetate and yttrium (III) acetate as source materials. The films preparation process was studied by varying annealing temperature after the preparation of gel films by spin coating, followed by thermal annealing at higher temperature. In the present work, one step annealing directly from Cu-Y-gel under nitrogen flow was used. X-ray diffraction (XRD) revealed that the film annealed at 800<sup>。</sup>C is significantly c-axis oriented, shows only (002) and (004) peaks at 15.6<sup>。</sup> and 31.5<sup>。</sup>, respectively. The optical bandgap of 3.7 - 3.8 eV is estimated by (αhν)2 plot which is higher than previous works. In addition, the films with highly c-axis orientation showed photoluminescence (PL) at room temperature with very broad peak at 2.3 eV. The films annealed at different temperature showed different structural properties.
