Synthesis and Characterization of Cerium-Doped Lutetium Aluminum Garnet Phosphors by Nitrate-citrate Sol-Gel Combustion Process

Nanosized cerium-doped lutetium aluminum garnet （LuAG：Ce） phosphors were prepared by nitrate-citrate solgel combustion process using 1：1 ratio of the citrate：nitrate. The prepared LuAG：Ce phosphors were characterized by XRD, TEM, photoluminescence and radioluminescence spectra excited by UV and X-ray, respectively. The purified crystalline phase of LuAG：Ce was obtained at 900 ℃ by directly crystallizing from amorphous materials. The resultant Lu- AG：Ce phosphors were uniform and had good dispersivity with an average particle size of about 30 urn. Both photoluminescence and radioluminescence were well-known Ce^3＋ emissions located in the range of 470 -600 nm consisting of two emission bands because of the transition from the lowest 5d excited state （2D） to the 4f ground state of Ce^3＋, which matched well with the sensitivity curve of the Si-photodiode. There was a little red shift for the emission components from the UV-excited emission spectrum to the X-ray-excited emission spectrum. The fast scintillation decay component of 26 ns satisfies the requirements of fast scintillators.

Synthesis and Structural Properties of Bismuth Doped Cobalt Nanoferrites Prepared by Sol-Gel Combustion Method

A series of Bismuth doped Cobalt nanoferrites of chemical composition CoBixFe2-xO4 (where x = 0.00, 0.05, 0.10, 0.15, 0.20 & 0.25) were prepared by sol-gel combustion method and calcinated at 600℃. The structural and morphological studies were carried out by using X-ray diffraction (XRD), Scanning Electron Microscope (SEM), Transmission Electron Microscopy (TEM), Energy Dispersive Spectroscopy (EDS) and Fourier Transform Infrared (FT-IR) spectra showing the single phase spinal structure. The X-ray diffraction (XRD) analysis confirmed a single phase fcc crystal. The crystallite size of all the compositions was calculated using Debye-Scherrer equation and found in the range of 17 to 26 nm. The lattice parameters were found to be decreased as Bi3+ ion doping increases. The surface morphology was studied by Scanning Electron Microscope (SEM) and particle size was confirmed by Transmission Electron Microscopy (TEM). The EDS plots revealed existence of no extra peaks other than constituents of the taken up composition. The Fourier Transform Infrared (FT-IR) studies were made in the frequency range 350 - 900 cm-1 and observed two strong absorption peaks. The frequency band is found at 596 cm-1 where as the lower frequency band at 393 cm-1. It is clearly noticed that the two prominent absorption bands were slightly shifted towards higher frequency side with the increase of Bi3+ ion concentration.

Synthesis, Characterization and Optical Morphology of ZnO Nanoparticles

The ZnO molecule plays an important role in the industry due to it special features, anti-corrosion anti-bacterial properties, as well as due to its low electrical conductivity and heat resistance. In these experimental researches, the sol-gel method was chosen, which enables control of nucleation, aging and growth of particles in the solution. ZnO synthesis was prepared utilizing chemical method with Zinc acetate dyhidrate and NaOH with the appropriate methanol solvent and heating (60˚C). The methods used in identification and characterization are FTIR, UV/VIS, OPTICAL MICROSCOPY, SEM and XRD. The FTIR spectra of synthesized ZnO with corresponding ones show characteristic bands at the corresponding wavelengths, which confirm the presence of ZnO nanoparticles. SEM characterization of ZnO shows the morphology of needle-shaped nanoparticles. XRD spectar in this research by chemical method indicates the particle size of 17.76 nm.

Bonding characteristics of the Al_2O_3-metal composite coating fabricated onto carbon steel by combustion synthesis

The fabrication of an alumina-metal composite coating onto a carbon steel substrate by using a self-propagating high-temperature synthesis technique was demonstrated. The effects of the type and thickness of the pre-coated layer on the binding structure and surface qual- ity of the coating were systematically investigated. The macrostructure, phase composition, and bonding interface between the coating and the substrate were investigated by scanning electronic microscopy （SEM）, X-ray diffraction （XRD）, and energy-dispersive X-ray spectrometry （EDS）. The diffraction patterns indicated that the coating essentially consisted of α-Al2O3, Fe（Cr）, and FeO-Al2O3. With an increase in the thickness of the pre-coated working layer, the coating became more smooth and compact. The transition layer played an important role in enhancing the binding between the coating and the substmte. When the pre-coated working layer was 10 mm and the pre-coated transition layer was 1 ram, a compact structure and metallurgical bonding with the substrate were obtained. Thermal shock test results indicated that the ceramic coating exhibited good thermal shock resistance when the sample was rapidly quenched from 800℃ to room temperature by plunging into water.

Application of Ceramic Coat Synthesized by In-Situ Combustion Synthesis to BF Tuyere

A novel technology of tuyere protection is introduced. The ceramic coat .is synthesized by using in-situ combustion process as the internal, external, and nose protecting coat of BF tuyeres. It can effectively protect the tuyeres and reduce heat loss by cooling water. The technglogy is quick-acting, easy to use, energy-saving and can make tuyeres have long service life. The feasibility of the application of the tuyere ceramic coat is discussed and the energy-saving effect of the tuyere is compared with that of the tuyeres lined with refractory.

Preparation of WC/CoCrFeNiAl0.2 high-entropy-alloy composites by high-gravity combustion synthesis

The WC/CoCrFeNiAl0.2 high-entropy alloy(HEA)composites were prepared through high-gravity combustion synthesis.The preparation method is presented below.First,using a designed suitable multiphase thermite system,the molten CoCrFeNiAl0.2 HEA was fabricated using low-cost metal oxides.The molten HEA was subsequently infiltrated into the WC layer to fabricate WC/CoCrFeNiAl0.2 composites in a highgravity field.The porosity of the WC/CoCrFeNiAl0.2 composites was down-regulated,and their compressive yield strength was up-regulated when the high-gravity field was increased from 600g to 1500g because this infiltration process of a HEA melt into the WC layer is driven by centrifugal force.The WC particles in the composites exhibited a gradient distribution along the direction of the centrifugal force,which was attributed to the combined action of the high-gravity field and the temperature gradient field.The Vickers hardness of the sample was down-regulated from 9.53 to 7.41 GPa along the direction of the centrifugal force.

Preparation of Nano Y_2O_2S∶Eu Phosphor by Ethanol Assisted Combustion Synthesis Method

Y2O2S：Eu nano crystallines were prepared by a new ethanol assisted combustion synthesis method using sulfurcontained organic fuel in an ethanol-aqueous solution. The as-prepared nanocrystallines were characterized by X-ray diffraction, transmission electron microscope, photoluminescence spectra and X-ray luminescence spectra. It is shown that the assistant fuel ethanol has the effect of decreasing the water needed, simplifying the experiment procedure by dissolving rare earth nitrate and sulfur-contained organic fuel into an even solution, and prompting the formation of rare earth oxysulfide by igniting firstly during heating that leads to combustion decomposition reaction. Y2O2S ： Eu nano crystallines with strong photoluminescence and X-ray luminescence are obtained using thioacetamide as organic fuel. Mixtures of Y2O3 ： Eu and Y2O2S ： Eu are acquired using thiourea as fuel, and the content of Y2O2S ： Eu increases until reaches to about half of the Y2O3 ： Eu with the increasing amount of thiourea. Y2O2SO4 ： Eu emerges when S/Y = 6 and increases with increasing thiourea amount.

Combustion synthesis of fine TiFe series alloy powder by magnesothermic reduction of ilmenite

Fine TiFe series alloy powder was fabricated by magnesothermic reduction of ilmenite as main raw material. Adiabatic temperature of the FeTiO3-Mg system was studied through thermodynamic analysis. Meanwhile, the characteristics of TiFe series alloy were described by XRD, SEM and grading analysis. It is shown that combustion synthesis of the FeTiO3-Mg system can carry out due to its strong exothermic reaction through adiabatic temperature calculate. Ultrafine TiFe series alloy powder after leached for 5 h has reasonable phases and morphology with the particle distribution of 0.2 to 1 μm. It indicates that in-situ magnesothermic reduction of natural ilmenite is a feasible way to fabricate ultrafine powder with a relatively lower cost.

Synthesis of Neodymium-Doped Yttrium Aluminum Garnet (Nd∶YAG) Nano-Sized Powders by Low Temperature Combustion

The homogeneously dispersed, less agglomerated (Nd0.01Y0.99)3Al5O12 nano-sized powders were synthesized by the low temperature combustion (LCS), using Nd2O3, Y2O3, Al(NO3)3·9H2O, ammonia water and citric acid as starting materials. This method effectively solves the problems caused by solid-state reaction at high temperature and hard agglomerates brought by the chemical precipitation method. The powders were characterized by TG-DTA, XRD, FT-IR, TEM respectively and the photoluminescence (PL) spectra of (Nd0.01Y0.99)3Al5O12 green and sintered ceramic disks were measured. The results show that the forming temperature of YAG crystal phase is 850 ℃ and YAP crystal phase appearing during the calcinations transforms to pure YAG at 1050 ℃. The particle size of the powders synthesized by the LCS is in a range of 20～50 nm depending on the thermal treatment temperatures. The effectively induced cross section (σin) with the value 4.03×10-19 cm2 of (Nd0.01Y0.99)3Al5O12 ceramics is about 44% higher than that of single crystal.

One-Step Synthesis of Nanocrytalline Perovskite LaMnO_3 Powders via Microwave-Induced Solution Combustion Route

Perovskite LaMnO3 powders with an average crystallite size of 12.5 nm were rapidly synthesized via a microwave-induced autocombustion reaction using glycine as a fuel and nitrate as an oxidant. After self-propagating combustion, the desired nanocrystalline perovskite LaMnO3 was obtained and no further calcination was carried out. The possible processes of combustion reaction were discussed according to the principle of propellant chemistry. The autocombustion and thermal decomposition of the precursor were investigated using the TG-DTA and FT-IR techniques. The influences of glycine-nitrate molar ratio and heat-treatment temperature on the perovskite phase formation and crystallite size of as-burnt powder were studied by XRD. The morphology and size of the as-burnt powder before and after milling were characterized and compared by TEM.

Mechanism of Combustion Synthesis of TiC-Ti Cermet

In order to investigate the mechanism of combustion synthesis of TiC-Ti cermet, a mixture of Ti and C was used for a combustion front quenching test, and the microstructural evolution in the quenched sample was analyzed by scanning electron microscopy （SEM） and energy dispersive X-ray （EDX）. Also, a temperature-time profile of the combustion reaction was measured. Based on the experimental results, a reaction-dissolution-precipitation mechanism of the combustion synthesis of TiC-Ti was proposed.

Fabrication and characterization of Al_2O_3-metal composite coating on steel plate with nonpressure combustion synthesis

Al2O3-metal composite coatings with different reactants and diluents were fabricated on mild steel plate with nonpressure combustion synthesis process. The coat-ings were characterized by means of X-ray diffraction, scanning electron microscopy, and energy-dispersive spec-trometry, respectively. Thermal shock tests were carried out to determine the bond strength of the coating with the steel substrate. The results indicate that the coating is composed of α-A1203, α-（Fe-Cr） and Al2SiO5 as the main phases. It is found that the coating with the diluents of Al2O3-SiO2 and transition layer of Al2O3-Cr presents the hi.ghest hardness of 2270 HV0.2 and the lowest porosity of 3.93 %. Owing to a metallurgical bond of the coating-to-substrate, the coating exhibits a good thermal shock resistance.

Formation of layer-shaped pores in TiC-Fe cermet by combustion synthesis

To study the formation of layer shaped pores in TiC Fe cermet, two Ti C Fe powder compacts containing Ti powders with two size ranges (< 44μm and 135～ 154μm ) respectively were ignited in a special ignition mode. The combustion temperatures of the reactions were measured, the phase constituents of the combustion synthesized products were inspected by X ray diffractometry (XRD), and the structures of the products were observed with scanning electron microscope (SEM). In the case of the finer Ti powder used, TiC Fe cermet and pore rank in an alternately laminar shape, and the shape of the pore is the same as that of the combustion wavefront, implying that the layer shaped pore results from a gather of the retained gas into the combustion wavefront. While in the case of the coarser Ti powder used, the lower combustion temperature causes the gather of the retained gas to be difficult, the pore being present in an arbitrary shape and distributing randomly.

Fabrication and Photoluminescence Properties of Hexagonal Micro-pyramids ZnO Powders by Combustion Synthesis

The ZnO powder with hexagonal-pyramids structure was prepared by the low-temperature combustion process. Ammonium acetate was used as the fuels, whereas zinc nitrate acted as the oxidant. The effect of different ration between fuel and oxidant on the morphology and photoluminescence （PL） characteristic was studied. The formation of hexagonal-pyramids structure was discussed. The optimum preparing parameter for fine morphology is that the ratio of zinc nitrate and ammonium acetate is 1：5, and ignition temperature is 500 ℃. The PL measurement indicates all samples have the strong blue and yellow emission peak. The changes of surface energy of the polar surfaces result in the formation of micro-pyramids structure.

Preparation of TiAl/Al_2O_3 composites by combustion synthesis

Studies the combustion synthesis of Al Ti TiO 2 system and concludes that, due to its low exothermic nature, a stable combustion wave can be maintained only when the system is ignited at a certain preheating temperature, and coupled with appropriate pseudo HIP process, dense TiAl/Al 2O 3 composites with density as high as 97% of the theoretical value can be produced, and points out. Microstructure observation shows in situ formed Al 2O 3 particles are of an average size smaller than one micron, and the hardness of TiAl matrix is enhanced by introduction of these particles.

Combustion Synthesis of TiB_2 Ceramics Powder from B_2O_3-TiO_2-Mg System in Air Atmosphere

TiB_2 ceramics powder was synthesized from B_2O_3-TiO_2-Mg system. The effects of TiB_2 addition as diluent on the combustion synthesis process were investigated. The results of thermodynamic calculation and experiments show that the increase of TiB_2 content ranging from 0 to 20wt% can reduce the adiabatic temperature T_(ad) from 3100 K to 2896 K and combustion temperature T_c from 2139 K to 1621 K respectively. The particle size and half width of the particle distribution are also increased with the addition of TiB_2 increasing from 0 to 20wt%. The combustion product is a mixture of TiB_2, MgO, and other intermediate phases. The leached product contains mainly TiB_2, TiO_2 and TiN, and its oxygen content is 7.77wt%.

Reaction dynamics in the combustion synthesis system of Al-CrO_3-Al_2O_3-NaF-N_2-O_2

A new material with heat-resistant and adiabatic characteristics and high strength was prepared using the combustion synthesis method by mixed powders of CrO3, Al, Al2O3, and NaF in atmospheric gas. The reaction dynamic process of the Al-CrO3-NaF-Al2O3-N2-O2 new material system by the combustion synthesis method was discussed based on the observation results by SEM, EDS, and XRD in combination with the combustion front quenching method （CFQM） and the relation curves between reaction free enthalpies and the corresponding temperatures. The combustion synthesis mechanism and the formation reasons of the phase in the combustion product were analyzed.

Synthesis and characterization of SrCe_(0.95)Y_(0.05)O_(3-δ) nano powders by low temperature combustion

Nanosized SrCe0.95Y0.05O3-δ powders with homogeneous composition were synthesized by the low temperature combustion process based on the Pechini method. A polymeric precursor sol was formed by using citric acid and ethylene glycol as the chelating agents of metal ions. The perovskite-type SrCe0.95Y0.05O3-δpowders with uniform shape and smaller than 25 nm in size were obtained through the combustion of the polymeric precursor sol at the existence of nitric acid and ammonium hydroxide. It was found that modulating the quantifies of nitric acid and ammonium hydroxide could control the particle size, and the quantities of residue carbonate ions were also affected by the quantifies of citric acid and ethylene glycol.