Suppressing Charge Recombination in ZnO-Nanorod-Based Perovskite Solar Cells with Atomic-Layer-Deposition TiO2

ZnO nanorods are passivated with a TiO2 interracial layer and applied in the CH3NH3PbI3 perovskite solar cell, which prepared by the atomic layer deposition method show a positive effect on the tiff factor and power conversion efficiency. With TiO2 interracial passivation, the charge recombination in the ZnO/CH3NH3PbI3 interface is effectively suppressed and the maximum power conversion efficiency is enhanced from 11.9% to 13.4%.

Preparation and performance of dye-sensitized solar cells based on ZnO-modified TiO_2 electrodes

The ZnO-modified TiO2 electrode was prepared by adding Zn（CH3COO）2·2H2O to the TiO2 colloid during the sol-gel production process, and was used in dye-sensitized solar cells （DSCs）. The open circuit voltage （Voc） and fill factor （if） of the cells were improved sig- nificantly. The performances of the ZnO-modified TiO2 electrode such as dark current, transient photocurrent, impedance, absorption spectra, and fiat band potential （Vfb） were investigated. It is found that the interface charge recombination impedance increases and Vfb shifts about 200 mV toward the cathodic potential. The effect mechanism of ZnO modification on the performance of DSCs may be that ZnO occupies the surface states of the TiO2 film.

Facile fabrication of TiO_2 nanoparticle–TiO_2 nanofiber composites by co-electrospinning–electrospraying for dye-sensitized solar cells

We report a facile method for the fabrication of TiO2 nanofiber-nanoparticle composite （FP） via. simulta- neous electrospraying and electrospinning for dye-sensitized solar cell （DSC） applications. The loading of nanoparticles on the fibers is controlled by varying their feed rates during electrospinning. The FP composites having three different particle loading are prepared by the methodology and the FP with the highest particle loading （denoted as FP-3 in the manuscript） showed the best overall efficiency of 9.15% in comparison to the other compositions of the FP （FP-2, 8.15% and FP-1, Z51%, respectively） and nanofibers （F） and nanoparticles （P） separately （7.21 and 7.81, respectively）. All the material systems are characterized by spec- troscopy, microscopy, surface area measurements and the devices are characterized by current-voltage （I-V）, incident photon-to-current conversion efficiency （IPCE）, electrochemical impedance measurements, etc. I-V, dye-loading and reflectance measurements throw light on the overall performance of the DSC devices.

Effect of hydroxyl on dye-sensitized solar cells assembled with TiO_2 nanorods

YiO2 nanorods have been prepared on ITO substrates by dc reactive magnetron sputtering technique. The hydroxyl groups have been introduced on the nanorods surface. The structure and the optical properties of these nanorods have been studied. The dye-sensitized solar cells （DSSCs） have been assembled using these TiO2 nanorods as photoelectrode. And the effect of the hydroxyl groups on the properties of the photoelectric conversion of the DSSCs has been studied.

ZnO Spin-Coating of TiO₂Photo-Electrodes to Enhance the Efficiency of Associated Dye-Sensitized Solar Cells

Dye-sensitized solar cells (DSSCs) with ZnO spin-coated TiO2 photo-electrodes are compared to DSSC with a bare TiO2 photo-electrode. It is demonstrated that the deposited ZnO of controlled amount, by varying the precursor concentration in the coating sol, can indeed enhance the performance of the DSSC. The measured power conversion efficiency shows a maximum around the precursor concentration 0.1 M and falls down sharply to 0% beyond this point. The results are interpreted on the basis of two competing factors: At ZnO concentrations less than 0.1 M, the formation of an energy barrier increases the photocurrent by reducing the rate of interfacial back-recombination. At ZnO concentrations greater than 0.1 M, the screening of the TiO2 film by thicker ZnO layers decreases the photocurrent through the reduction of TiO2 dye-adsorption efficiency.

Synthesis and application of TiO_2 single-crystal nanorod arrays grown by multicycle hydrothermal for dye-sensitized solar cells

TiO2 is a wide band gap semiconductor with important applications in photovoltaic cells. Vertically aligned Tit2 nanorod arrays （NRs） are grown on the fluorine-doped tin oxide （FTO） substrates by a multicycle hydrothermal synthesis process. The samples are characterized by X-ray diffraction （XRD）, scanning electron microscopy （SEM）, high-resolution transmission electron microscopy （HRTEM）, and selected-area electron diffraction （SAED）. It is found that dye-sensitized solar cells （DSSCs） assembled by the as-prepared Tit2 single-crystal NRs exhibit different trends under the condition of different nucleation and growth concentrations. Optimum cell performance is obtained with high nucleation concentration and low growth cycle concentration. The efficiency enhancement is mainly attributed to the improved specific surface area of the nanorod.

Theoretical Study on Electronic, Optical, and Charge Transfer Properties of Starburst Triphenylamine as Sensibilizer @TiO2 Cluster for Dye-sensitized Solar Cells

Here, a series of starburst triphenylamine(WD8) derivatives for dye-sensitized solar cells(DSSCs) applications have been designed. The frontier molecular orbitals(FMOs) property, absorption spectra, and charge transfer rate property of WD8 and its derivatives were simulated. We also evaluated the FMOs energies and absorption spectra of WD8 and its derivatives with the TiO2 cluster. The simulation results show that the phenothiazine-triphenylamine and 2-cyanoacetic acid groups in the ortho-position will increase the HOMO energy, decrease the LUMO energy, and narrow the HOMO-LUMO gap of WD8. The charge injection from WD8 and its derivatives to TiO2 should be more favorable. The phenothiazine-triphenylamine and 2-cyanoacetic acid groups in the ortho-position will decrease the electron and hole injection barriers of WD8. The phenothiazinetriphenylamine and 2-cyanoacetic acid groups in the ortho-position will improve the absorption spectra properties of WD8. The absorption spectra of WD8 and its derivatives with the TiO2 cluster would have a red shift. The phenothiazine-triphenylamine and 2-cyanoacetic acid groups in the ortho-position will increase the charge transfer property of WD8.

Influence of Modification of Counter Electrode on PhotoelectricProperties of Dye-sensitized TiO_2 Solar Cells

A dye-sensitized nanocrystalline TiO 2 solar cell(DYSC) was assembled, of which counter electrode was modified already by platinum, nickel and carbon. It was found that the DYSC had better photoelectric performance when the electrode was modified by platinum than by nickel and carbon. The influence of the incidence light wavelength on the incidence monochromatic photoelectric conversion efficiency(IPCE) was investigated. The result shows that the IPCE mainly depends on the short-circuit current density(I SC) of a DYSC, and the IPCE reaches 48.32% under the irradiation with the wavelength of 560 nm when the counter electrode of a DYSC was modified by platinum. The influence of incident light intensity on the photoelectric properties of a DYSC was also investigated. It was found that the I SC and open-circuit voltage(V OC) increased and the fill factor(f f) of the DYSC decreased with the increase of the incident light intensity.

Review on development of electrolytes for dye-sensitized solar cells

Since the prototype of a dye-sensitized solar cell(DSSC)was reported in 1991 by M. Gratzel,it has aroused intensive interest over the past decade due to its low cost and simple preparation procedure.The typical cell consists of a dye-coated mesoporous nanocrystalline TiO_2 film sandwiched between two transparent electroldes.A liquid electrolyte,traditionally containing the trioidide/iodide redox couple,fills the pores of the mesoporous nanocrystalline TiO_2 film and contacts the nanoparticles.Photoexcite...

Spray Pyrolyzed TiO2 Embedded Multi-Layer Front Contact Design for High-Efficiency Perovskite Solar Cells

The photovoltaic performance of perovskite solar cells(PSCs)can be improved by utilizing efficient front contact.However,it has always been a significant challenge for fabricating high-quality,scalable,controllable,and cost-effective front contact.This study proposes a realistic multi-layer front contact design to realize efficient single-junction PSCs and perovskite/perovskite tandem solar cells(TSCs).As a critical part of the front contact,we prepared a highly compact titanium oxide(TiO2)film by industrially viable Spray Pyrolysis Deposition(SPD),which acts as a potential electron transport layer(ETL)for the fabrication of PSCs.Optimization and reproducibility of the TiO2 ETL were discreetly investigated while fabricating a set of planar PSCs.As the front contact has a significant influence on the optoelectronic properties of PSCs,hence,we investigated the optics and electrical effects of PSCs by three-dimensional(3D)finite-difference time-domain(FDTD)and finite element method(FEM)rigorous simulations.The investigation allows us to compare experimental results with the outcome from simulations.Furthermore,an optimized single-junction PSC is designed to enhance the energy conversion efficiency(ECE)by>30% compared to the planar reference PSC.Finally,the study has been progressed to the realization of all-perovskite TSC that can reach the ECE,exceeding 30%.Detailed guidance for the completion of high-performance PSCs is provided.

A Composite Photoanode Based on P25/TiO2 Nanotube Arrays/ Flower-Like TiO2 for High-Efficiency Dye-Sensitized Solar Cells

In this work, a three-layer TiO2 composite film consisting of flower-like TiO2 （Flo-TiO2） as overlayer, TiOa nanotube arrays as interlayer and TiO2 nanoparticle （P25） as underlayer was fabricated as the photoelectrode of dyesensitized solar cells （DSSCs）. Due to the introduction of Flo-TiO2, the three-layer composite film has strong lightscattering ability. Then, we have investigated and compared the photoelectric conversion properties of DSSCs based on three-layer structure （P25/TNT arrays/Flo-TiO2） photoelectrode and double-layer film （P25/TNT arrays） photoelectrode. It is found that DSSCs based on three-layer structure exhibit a high power conversion efficiency of 6.48% compared with the DSSCs composed of double-layer film （5.11%）.

Inside-out Ostwald ripening： A facile process towards synthesizing anatase TiO2 microspheres for high- efficiency dye-sensitized solar cells

A facile inside-out Ostwald ripening route to the morphology-controlled preparation of TiO2 microspheres is developed. Here, TiO2 hollow microspheres （HM） and solid microspheres （SM） are prepared by adjusting the volume ratio of isopropanol （IPA） to acetylacetone （Acac） in the solvothermal process. During the formation process of HM, precipitation of solid cores, subsequent deposition of outer shells on the surface of cores, and simultaneous core dissolution and shell recrystallizafion are observed, which validate the inside-out Ostwald ripening mechanism. Design and optimization of the properties （pore size, surface area, and trap state） of TiO2 microspheres are vital to the high performance of dye- sensitized solar cells （DSSCs）. The optimized TiO2 rnicrospheres （rHM and rSM） obtained by post-processing on recrystallization, possess large pore sizes, high surface areas and reduced trap states （Ti3~ and oxygen vacancy）, and are thus ideal materials for photovoltaic devices. The power conversion efficiency of DSSCs fabricated using rHM photoanode is 11.22%, which is significantly improved compared with the 10.54% efficiency of the rSM-based DSSC. Our work provides a strategy for synthesizing TiO2 microspheres that simultaneously accommodate different physical properties, in terms of surface area, crystallinity, morphology, and mesoporosity.

Synthesis of nano-TiO2 assisted by diethylene glycol for use in high efficiency dye-sensitized solar cells

The performance of dye-sensitized solar cells（DSSCs） consisting of anatase TiO_2 nanoparticles that were synthesized via a hydrothermal method was studied.The synthesized TiO_2 nanoparticles were characterized by X-ray diffraction（XRD）,nitrogen sorption analysis,scanning electron microscopy（SEM）,high resolution transmission electron microscopy（HRTEM）,and UV-vis spectroscopy.Then the J-Vcurve,electrochemical impedance spectroscopy（EIS）,and open-circuit voltage decay（OCVD） measurement were applied to evaluate the photovoltaic performance of DSSCs.Compared with the commercial TiO_2nanoparticles（P25）,the synthesized-TiO_2 nanoparticles showed better performance.By adding diethylene glycol（DEG） before the hydrothermal process,the synthesized TiO_2 nanoparticles（hereafter referred to as TiO_2-DEG particles） shows narrower size distribution,larger specific surface area,higher crystallinity,and less surface defects than TiO_2（DEG free） particles.The analysis of photovoltaic properties of DSSCs based on TiO_2-DEG particles showed that the recombination of electron-hole pairs was decreased and the trapping of carries in grain boundaries restrained.It was believed that the photoelectrode fabricated with the as-prepared TiO_2 nanoparticles improved the loading amount of dye sensitizers（N719）.and enhanced the photocurrent of the DSSCs.As a result,the TiO_2-DEG particle based cells achieved a photo-to-electricity conversion efficiency（η） of 7.90%,which is higher than 7.53%for the cell based on TiO2（DEG free） and 6.59%for the one fabricated with P25.

Dye-sensitized TiO2 Solid Solar Cell Using Poly (4-vinylphenyloxy-methyltriphenylamine) as Hole Transport Material

A dye-sensitized TiO2 solid solar cell, which contains poly(4-vinylphenyloxy-methyltriphenylamine) in hole transport layer (HTL) doped with LiSCN and methyl-hexyl-imidazolium iodide (MHIml), was prepared. The solar cell shows that the conversion efficiency is 0.59%, Jsc is 3.03mA/cm2, and V^ is 0.53V at 1 sun light intensity.

Increase in efficiency of dye-sensitized solar cells by porous TiO_2 layer modification with gadolinium-containing thin layer

Modified with gadolinium-containing layer, nanoporous titania electrode and its application in dye-sensitized solar cells were reported. The electrode prepared was characterized with UV-Vis and X-ray diffraction （XRD） techniques. The amount of gadolinium was measured with inductively coupled plasma-optical emission spectrometry （ICP-OES） experiments. The modified electrode showed reduced N3 dye adsorption ability, but increased light conversion efficiency in comparison with the non-modified electrode. The overall conversion efficiencies, determined under 400 W/m2 irradiation with tungsten-halogen lamp at room temperature, were 0.55% for non-modified and 0.74% for modified electrodes.

Influence of TiCl_4 treatment on performance of dye-sensitized solar cell assembled with nano-TiO_2 coating deposited by vacuum cold spraying

Titanium tetrachloride (TiCl4) treatment was employed to TiO2 coating deposited on fluoride-doped tin oxide (FTO) conducting glass and indium oxide doped tin oxide (ITO) conducting glass, respectively. The nano-crystalline TiO2 coating was deposited using a composite powder composed of polyethylene glycol (PEG) and 25 nm TiO2 particles by vacuum cold spraying (VCS) process. A commercial N-719 dye was used to adsorb on the surface of TiO2 coating to prepare TiO2 electrode, which was applied to assemble dye-sensitized solar cell (DSC). The cell performance was measured under simulated solar light at an intensity of 100 mW·cm-2. Results show that with an FTO substrate the DSC composed of a VCS TiO2 electrode untreated by TiCl4 gives a short-circuit current density of 13.1 mA·cm-2 and an open circuit voltage of 0.60 V corresponding to an overall conversion efficiency of 4.4%. It is found that after TiCl4 treatment to the VCS TiO2 electrode with an FTO substrate, the short circuit current density of the cell increases by 31%, the open-circuit voltage increases by 60 mV and a higher conversion yield of 6.5% was obtained. However, when an ITO substrate is used to deposit TiO2 coating by VCS, after TiCl4 treatment, the conversion efficiency of the assembled cell reduces slightly due to corrosion of the conducting layer on the ITO glass by TiCl4.

A Bi-layer Composite Film Based on TiO_2 Hollow Spheres, P25,and Multi-walled Carbon Nanotubes for Efficient Photoanode of Dye-sensitized Solar Cell

A bi-layer photoanode for dye-sensitized solar cell(DSSC) was fabricated, in which TiO_2 hollow spheres(THSs) were designed as a scattering layer and P25/multi-walled carbon nanotubes(MWNTs) as an under-layer. The THSs were synthesized by a sacrifice template method and showed good light scattering ability as an over-layer of the photoanode. MWNTs were mixed with P25 to form an under-layer of the photoanode to improve the electron transmission ability of the photoanode. The power conversion efficiency of this kind of DSSC with bi-layer was enhanced to 5.13 %,which is 14.25 % higher than that of pure P25 DSSC.Graphical Abstract A bi-layer composite photoanode based on P25/MWNTs-THSs with improved light scattering and electron transmission, which will provide a new insight into fabrication and structure design of highly efficient dyesensitized solar cells.

Preparation and characterization of TiO_2 photoelectrode codoped with aluminum and boron and its application in dye-sensitized solar cell

Nanocrystalline titania films codoped with aluminum and boron were prepared by cathodic vacuum arc deposition. In the process, titanium alloy target was used under an O2/Ar atmosphere, and sensitization of films were carried out by natural dye-sensitized complex in anhydrous ethanol. The structure, surface morphology and UV-vis spectra of titania films codoped were measured by X-ray diffraction analysis, scanning electron microscopy and ultraviolet-visible spectrometer. The as-deposited films are found to be amorphous. The films annealed were examined to be of anatase structure with orientation along the (101) planes, the average crystal size is in the range between 41 and 45 nm. SEM results show that there are some pores in the codoped titania films, the optical properties of the dye-sensitized films were also measured which reveals that the spectral responses of films shift to the visible region. Under simulated sunlight illumination, the overall energy conversion efficiency of dye-sensitized nanocrystalline solar cell is 0.9%.

Triton Facilitated Spherical TiO₂Nanoparticles and Their Advantage in a Dye-Sensitized Solar Cell

Spherical TiO2 particles (60 nm) were obtained by using a Triton X-100. The surfactant was employed in two stages, i.e., in the hydrolysis of TiCl4 and then in the precipitation of the corresponding Ti (IV) polymers. The advantages of such spherical TiO2 particles were examined in terms of photovoltaic characteristics of a dye-sensitized solar cell (DSSC) using Orange IV dye as sensitizer. Significantly higher overall solar energy conversion efficiency was obtained for a DSSC using the film of these spherical TiO2 particles, compared with that of a cell using a TiO2 film prepared without surfactant.

Synthesis of Single-Crystalline Anatase TiO_2 Nanorods With High-Performance Dye-Sensitized Solar Cells

Single-crystalline anatase TiO2nanorods have been prepared by solvothermal method using tetrabutylammonium hydroxide（TBAH） as a morphology controlling agent.The obtained TiO2nanorods are dominated by a large percentage of {010} facets.The power conversion efficiency of dye-sensitized solar cell（DSSC） based on anatase TiO2nanorods（8.66%） exhibits a significant improvement（35%） compared to that of P25 TiO2（5.66%）.The high performance of the anatase TiO2nanorods solar cell is ascribed to their large percent of exposed {010} facets as well as balancing their surface areas and sizes.