Improving Heat Transfer in Parabolic Trough Solar Collectors by Magnetic Nanofluids

A parabolic trough solar collector(PTSC)converts solar radiation into thermal energy.However,low thermal efficiency of PTSC poses a hindrance to the deployment of solar thermal power plants.Thermal performance of PTSC is enhanced in this study by incorporating magnetic nanoparticles into the working fluid.The circular receiver pipe,with dimensions of 66 mm diameter,2 mm thickness,and 24 m length,is exposed to uniform temperature and velocity conditions.The working fluid,Therminol-66,is supplemented with Fe3O4 magnetic nanoparticles at concentrations ranging from 1%to 4%.The findings demonstrate that the inclusion of nanoparticles increases the convective heat transfer coefficient(HTC)of the PTSC,with higher nanoparticle volume fractions leading to greater heat transfer but increased pressure drop.The thermal enhancement factor(TEF)of the PTSC is positively affected by the volume fraction of nanoparticles,both with and without a magnetic field.Notably,the scenario with a 4%nanoparticle volume fraction and a magnetic field strength of 250 G exhibits the highest TEF,indicating superior thermal performance.These findings offer potential avenues for improving the efficiency of PTSCs in solar thermal plants by introducing magnetic nanoparticles into the working fluid.

Design and Development of a Parabolic Trough Solar Air Heater for a Greenhouse Dryer

Design and Development of a Parabolic Trough Solar Air Heater (PTSAH) for a Greenhouse Dryer (GD) was done to improve the dryer’s performance. The materials used for the fabrication of the PTSAH included galvanized sheets covered with aluminium foil, an absorber tube made of GI pipe painted matt black to increase heat absorbance at the focal line, mild steel square tubes, shutter plywood, and an axial fan to push air through the absorber tube. Key geometrical parameters used for the design of the PTSAH were a rim angle of 98 degrees, focal length of 0.2608 m, height of 0.3451 m, length of 2 m, and an aperture width of 1.2 m. The PTSAH’s total aperture surface area was 2.4 m2, while its absorber tube surface area was 0.1587 m2. The PTSAH was experimentally tested to establish its thermal performance. It was found that the ambient air recorded an average value of 31.1˚C and that the air heater could increase the air temperature by 45.6˚C above ambient with a thermal efficiency of 5.3%. It can, therefore, be concluded that the PTSAH can significantly improve the performance of a GD by supplying the GD with air at a higher temperature than ambient.

Demonstration of Pilot Scale Large Aperture Parabolic Trough Organic Rankine Cycle Solar Thermal Power Plant in Louisiana

During the calendar year of 2012 the University of Louisiana at Lafayette in conjunction with CLECO Power LLC (CLECO) has constructed and commissioned a pilot scale parabolic trough solar thermal power plant for the first time in Louisiana. The large aperture trough (LAT) solar collectors were provided by Gossamer Space Frames and are coupled with an organic Rankine cycle (ORC) power block provided by ElectraTherm, Inc. for study of the feasibility of cost-effective commercial scale solar thermal power production in Louisiana. Supported by CLECO and providing power to the existing CLECO grid, the implementation of state-of-the-industry collector frames, mirrors, trackers, and ORC power block is studied under various local weather conditions which present varied operating regimes from existing solar thermal installations. The solar collectors provide a design output of 650 kWth and preliminary actual performance data from the system level is presented. The optimal size, configuration and location for such a plant in the given solar resource region are being studied in conjunction with CLECO’s search for optimal renewable energy solutions for the region. The pilot scale size of the facility and implementation of the simpler ORC allow remote operation of the facility and flexibility in operating parameters for optimization studies. The construction of the facility was supported by the Louisiana Department of Natural Resources, the U.S. Department of Energy, and CLECO. The continued operation of the plant is supported by CLECO Power LLC and the University of Louisiana at Lafayette.

Modelling of Solar Thermal Power Plant Using Parabolic Trough Collector

The target of the National Solar Mission is to build up India as a worldwide pioneer in solar energy generation. Solar power can be transmitted through grid either from solar photovoltaic or solar thermal technology. As compared to solar photovoltaic, solar thermal installations are less studied, especially regarding energy estimation and performance analysis. For estimating the potential of CSP plants, it is planned to simulate a power plant. We have marginally modified the design of 1 MW operational power plant installed at Gurgaon using Parabolic Trough Collector (PTC) technology. The results are compared with the expected output of Gurgaon power plant and also 50 MW power plant at Rajasthan. Our results have closely matched with a small deviation of 3.1% and 3.6% for Gurgaon and Rajasthan plants, respectively. Our developed model is also validated with 18 different solar power plants in different parts of the world by slightly modifying the parameters according to the plant capacity without changing major changes to the plant design. Difference between our results and the expected energy generation varied from 0.4% to 13.7% with an average deviation of 6.8%. As our results show less than 10% deviation as compared to the actual generation, an attempt has been made here to estimate the potential for the entire nation. For this modelling has been carried out for every grid station of 0.25° × 0.25° interval in India. Our results show that annual solar thermal power plant of 1 MWe capacity potential varies from 900 to 2700 MWh. We have also compared our results with previous studies and discussed.

Preparation and Characterization of Andalusite Ceramic Used for Solar Thermal Power Generation

High-temperature thermal storage material is one of the critical materials of solar thermal power generation system. Andalusite, kaolin, talc, γ-Al2O3 and partially stabilized zireonia were used as the raw materials, and in-situ synthesis of cordierite was adopted to fabricate thermal storage material for solar thermal power generation via pressureless sintering. The phase compositions, microstructures and thermal shock resistances of the sintered samples were analyzed by XRD, SEM and EDS, and the corresponding mechanical properties were measured. The results show that the major phases of the samples are mullite and zirconium silicate, and the pores distribute uniformly. After being sintered at 1 460℃C, A4 sample exhibits a better mechanical performance and thermal shock resistance, its loss rate of bending strength after 30 cycles thermal shock is 3.04%, the bulk density and bending strength are 2.86 g.cm^-3 and 139.66 MPa, respectively. The better thermal shock resistance of the sample is closely related to the effect of zirconium silicate, such as its uniform distribution, nested growth with mullite, low thermal expansion coefficient, high thermal conductivity, etc. This ceramic can be widely used as one of potential thermal storage materials of solar thermal power generation system.

In-Situ Preparation and Thermal Shock Resistance of Mullite-Cordierite Heat Tube Material for Solar Thermal Power

In order to improve the thermal shock resistance of solar thermal heat transfer tube material, the mullite-cordierite composite ceramic as solar thermal heat transfer tube material were fabricated by pressureless sintering using a-Al203, Suzhou kaolin, talc, and feldspar as starting materials. The important parameter for solar thermal transfer tube such as water absorption （W）, bulk density （Db）, and the mechanical properties were investigated. The phase composition and microstructure of the composite ceramics were analyzed by XRD and SEM. The experimental results show that the B3 sintered at 1 300 ℃ and holding for 3 h has an optimum thermal shock resistance. The bending strength loss rate of B3 is only 2% at 1 100℃ by air quenching-strength test and the sample can endure 30 times thermal shock cycling, and the water absorption, the bulk density and the bending strength are 0.32%, 2.58 g·cm-3, and 125.59 MPa respectively. The XRD analysis indicated that the phase compositions of the sample were mullite, cordierite, corundum, and spinel. The SEM images illustrate that the cordierite is prismatic grain and the mullite is nano rod, showing a good thermal shock resistance for composite ceramics as potential solar thermal power material.

Optimization of solar thermal power station LCOE based on NSGA-Ⅱ algorithm

In view of the high cost of solar thermal power generation in China,it is difficult to realize large-scale production in engineering and industrialization.Non-dominated sorting genetic algorithm II(NSGA-II)is applied to optimize the levelling cost of energy(LCOE)of the solar thermal power generation system in this paper.Firstly,the capacity and generation cost of the solar thermal power generation system are modeled according to the data of several sets of solar thermal power stations which have been put into production abroad.Secondly,the NSGA-II genetic algorithm and particle swarm algorithm are applied to the optimization of the solar thermal power station LCOE respectively.Finally,for the linear Fresnel solar thermal power system,the simulation experiments are conducted to analyze the effects of different solar energy generation capacities,different heat transfer mediums and loan interest rates on the generation price.The results show that due to the existence of scale effect,the greater the capacity of the power station,the lower the cost of leveling and electricity,and the influence of the types of heat storage medium and the loan on the cost of leveling electricity are relatively high.

Solar Thermal Energy Generation Potential in Gujarat and Tamil Nadu States, India

Government of India has come out with an ambitious target of 100 GW of using solar energy alone by the year 2022. To reach this target, innovative ideas are required to use the solar energy more effectively. For solar electricity generation, mainly two types of technologies are presently in use, namely, solar PV and solar thermal. Being a tropical country, India has large solar PV and solar thermal energy. More research is required on economic aspects to make the solar thermal competitive to solar PV. Towards this direction, in our present study we have simulated a solar thermal power plant using Parabolic Trough Collector (PTC) technology and normalized with 1 MW solar thermal power plant at Gurgaon near New Delhi. Through simulation, we have extended our study and computed the electricity generation possible at different locations of India. For this purpose with 1? × 1?spacing, computations have been carried out at 296 locations. The work is further extended for more detailed study at two representative states, namely, Gujarat and Tamil Nadu. In these two states, closer data points with 0.25? × 0.25? spacing have been considered at 273 locations for Gujarat and 197 locations for Tamil Nadu. Our results indicate a large potential of electricity generation using solar thermal energy in southern states of India, namely, Tamil Nadu, Karnataka, Kerala, southern and western part of Andhra Pradesh and eastern part of Maharashtra. Good potential has also been observed in eastern parts of Gujarat and parts of Madhya Pradesh and eastern part of Rajasthan. The annual potential ranges from 1800 MWh to as much as 2600 MWh. Major parts of northern states, for example Uttar Pradesh, Bihar, West Bengal, Punjab, Jammu and Kashmir have medium range potential. Here, the annual potential ranges from 1000 to 1500 MWh. Poor range of potential is observed towards eastern parts of India and north eastern states. Here, the electricity generation potential ranges from 600 to 1200 MWh. Our results are useful to solar thermal developer and decision managers.

Numerical Model and Performance Validation of a Small-Scale Concentrating Solar Thermal Power Plant in Louisiana

A simplified numerical model of a small-scale (25 - 100 kWe) parabolic concentrating solar power (CSP) plant is presented that can be utilized during the planning stages for a CSP plant, utilizing only simplified information that would be available at the preliminary stages of a project. This is important because existing models currently used for planning purposes, such as the System Advisor Model (SAM) from the National Renewable Energy Laboratory (NREL), do not cover small-scale CSP plants. The model can be used to predict real-time performance, or it can be used with TMY data to estimate annual performance. The model was validated using performance data from an operating small-scale CSP power plant, which is a unique contribution of this work. The results showed that the model correlated well with actual operating measurements for all seasons of the year, and provided a useful tool for planning of future small-scale CSP plants.

Proposal of a Solar Thermal Power Plant at Low Temperature Using Solar Thermal Collectors

To this day, only two types of solar power plants have been proposed and built: high temperature thermal solar one and photovoltaic one. It is here proposed a new type of solar thermal plant using glass-top flat surface solar collectors, so working at low temperature (i.e., below 100°C). This power plant is aimed at warm countries, i.e., the ones mainly located between -40° and 40° latitude, having available space along their coast. This land based plant, to install on the seashore, is technologically similar to the one used for OTEC (Ocean Thermal Energy Conversion). This plant, apart from supplying electricity with a much better thermodynamic efficiency than OTEC plants, has the main advantage of providing desalinated water for drinking and irrigation. This plant is designed to generate electricity (and desalinated water) night and day and all year round, by means of hot water storage, with just a variation of the power delivered depending on the season.

Numerical Study of New-Type Receiver with Axially-Hollow Spiral Deflector for Parabolic Trough Direct-Steam-Generation Loop of Concentrating Solar Power System

The thermal stress-induced deformation issue of receiver is crucial to the performance and reliability of a parabolic-trough(PT) concentrating solar power(CSP) system with the promising direct steam generation(DSG) technology.The objective of the present study is to propose a new-type receiver with axially-hollow spiral deflector and optimize the geometric structure to solve the above issue.To this end,optical-flow-thermal multi-physics coupling models have been established for the preheating,boiling and superheating sections of a typical PT-DSG loop.The simulation results show that our proposed new-type receiver demonstrates outstanding comprehensive performance.It can minimize the circumferential temperature difference through the spiral deflector while lower the flow resistance cost through the axially hollow structure at the same time.As quantitatively evaluated by the temperature uniformity improvement(ε_(ΔT)) and the performance evaluation criteria(PEC),different designs are achieved based on different optimal schemes.When ε_(ΔT)is of primary importance,the optimal design with torsional ratio of 1 is achieved,with ε_(ΔT)=25.4%,25.7%,41.5% and PEC=0.486,0.878,0.596corresponding to preheating,boiling,superheating sections,respectively.When PEC is of primary importance,the optimal design with torsional ratio of 6-6.5 is achieved,with PEC=0.950,2.070,0.993 and ε_(ΔT)=18.2%,13.3 %,19.4% corresponding to preheating,boiling,superheating sections,respectively.

Performance Analysis of an Efficient Integration System of Coal-Fired Power Plant,Solar Thermal Energy and CO_(2)Capture

Coal-fired power plant is a major contributor to greenhouse gas emissions.The post-combustion capture is a promising method for CO_(2)emission reduction but the high thermal demand is unbearable.To address this issue,solar thermal energy and CO_(2)capture are jointly integrated into the coal-fired power plant in this study.The solar thermal energy is employed to meet the heat requirement of the CO_(2)capture process,thereby avoiding the electricity loss caused by self-driven CO_(2)capture.Furthermore,the heat released from the carbonation reaction of MgO adsorbent is integrated into the steam Rankine cycle.By partially substituting the extracted steam for feedwater heating,the electricity output of the power plant is further increased.According to the results from the developed model,the system could achieve a CO_(2)capture rate of 86.5%and an electricity output enhancement of 9.8%compared to the reference system,which consists of a self-driven CO_(2)capture coal-fired power plant and PV generation unit.The operational strategy is also optimized and the amount of CO_(2)emission reduction on a typical day is increased by 11.06%.This work shows a way to combine fossil fuels and renewable energy for low carbon emissions and efficient power generation.

Preliminary Design Study on Concentrated Solar Power PVRs to Operate with RCBC

Parabolic through concentrators and parabolic dish concentrators followed by a PVR （pressurized volumetric receiver） are proposed, studying the performance behavior of a RCBC （regenerative closed Brayton cycle） operating with helium or hydrogen. A pressurized gas such as helium circulates along the volumetric receiver, capturing the concentrated thermal solar energy to be further converted into electric power via a thermal cycle. The overall efficiency of the plant has been computed under variable parameters to determine the operating conditions for which efficiency and specific power are acceptable. As consequence of the proposed analysis, it is concluded that direct coupling between volumetric receivers and thermal engines renders high efficiency while avoiding an intermediate heat transfer medium.

SMO Algorithm to Unravel CEED Problem using Wind and Solar

This research proposes a more advanced way to address Combined Economic Emission Dispatch(CEED)concerns.Economic Load Dispatch(ELD)and Economic Emission Dispatch(EED)have been implemented to reduce generating unit fuel costs and emissions.When both economics and emission tar-gets are taken into account,the dispatch of an aggregate cost-effective emission challenge emerges.This research affords a mathematical modeling-based analyti-cal technique for solving economic,emission,and collaborative economic and emission dispatch problems with only one goal.This study takes into account both the fuel cost target and the environmental impact of emissions.This bi-inten-tion CEED problem is converted to a solitary goal function using a price penalty factor technique.In this case,a metaheuristic and an environment-inspired,intel-ligent Spider Monkey Optimization technique(SMO)are used to address the CEED dilemma.By following the generator’s scheduling process,the SMO meth-od is used to regulate the output from the power generation system in terms of pollution and fuel cost.The Fission-Fusion social(FFS)structure of spider mon-keys promotes them to utilize a global optimization method known as SMO dur-ing foraging behaviour.The emphasis is mostly on lowering the cost of generation and pollution in order to improve the efficiency of the power system and han-dle dispatch problems with constraints.The economic dispatch has been reme-died,and the improved result demonstrates that the system’s performance is stable andflexible in real time.Finally,the system’s output demonstrates that the system has improved in resolving CEED difficulties.When compared to ear-lier investigations,the proposed model’sfindings have improved.As the gener-ating units,wind and solar are used to explore the CEED crisis in the IEEE 30 bus system.

Off-Design Simulation of a CSP Power Plant Integrated with aWaste Heat Recovery System

Concentrating Solar Power(CSP)plants offer a promising way to generate low-emission energy.However,these plants face challenges such as reduced sunlight during winter and cloudy days,despite being located in high solar radiation areas.Furthermore,their dispatch capacities and yields can be affected by high electricity consumption,particularly at night.The present work aims to develop an off-design model that evaluates the hourly and annual performances of a parabolic trough power plant(PTPP)equipped with a waste heat recovery system.The study aims to compare the performances of this new layout with those of the conventional Andasol 1 plant,with the aim of assessing the improvements achieved in the new design.Based on the results,it can be concluded that the new layout has increased the annual generated power to almost 183 GWh(an increase of about 7.60% is achieved compared to the Andasol 1 layout that generates 169 GWh annually).Additionally,the proposed installation has achieved an efficiency of 20.55%,which represents a 7.87% increase compared to the previous design(19.05%).The Levelized Cost of Electricity(LCOE)of the new layout has been reduced by more than 5.8% compared to the Andasol 1 plant.Specifically,it has decreased from 13.11 to 12.35 c/kWh.This reduction in LCOE highlights the improved cost-effectiveness of the newlayout,making it amore economically viable option for generating electricity compared to the conventional Andasol 1 plant.

抛物面槽式太阳能集热器球形接头测试系统的研制与应用

球形接头是抛物面槽式太阳能集热器的关键部件,针对球形接头易发生运转卡涩和导热油泄漏问题,研制了一套球形接头性能测试系统。该测试系统可以实现球形接头在旋转、摆转或旋摆联动模式下,以及在导热油温度达393℃和压力达4.1 MPa工况条件下的加速寿命测试。以导热油为传热流体,开展了球形接头在导热油温度为393℃和压力为2.3 MPa工况条件,以及温度、压力变化条件下的性能测试研究,分析了球形接头在模拟12年寿命期的扭矩特性和密封性能,验证了该测试系统运行的稳定性和可靠性,并且关键技术参数的控制精度和测量精度满足使用要求,为球形接头的性能评价提供了技术支撑。

基于熔盐介质的大开口槽式集热器光热性能分析

建立了基于熔盐介质的槽式太阳能集热器的光学仿真模型和传热模型。经验证,传热介质出口温度与实际出口温度误差在±1%以内,周向能流密度误差在4.7%以内,表明所建模型准确性较高。分析了槽式集热器开口弦长、集热管直径、光学误差等对其光学性能的影响,以及法向直接辐照度、熔盐介质流速等对集热系统热性能的影响。结果表明,当开口弦长不变时,选择较大直径的集热管可以提高光学效率与截断因子,使系统热性能略有提高,而入射角和光学误差的增加会降低光学性能;增加法向直接辐照度或传热介质流速可以提高系统热效率。

Design and performance investigation of modified dual reflector parabolic trough collector with double planar mirrors

In a typical parabolic trough collector(PTC), sunlight is concentrated at the bottom of the absorber tube. This concentrated solar flux leads to uneven heat distribution, resulting in high local temperatures and significant thermal stress on the absorber tube.These limitations have restricted the application of PTCs in solar thermochemistry and other fields and have impacted their safe operation. In this study, a new PTC with dual planar mirrors(DPMS) is proposed to homogenize the circumferential solar flux distribution of the absorber tube. A design method and single-objective optimization of the new PTC with a DPMS are proposed,and an uncertainty analysis of the operational and structural parameters is performed. A coupled light-heat-structure numerical model was developed to study the heat transfer performance and structural mechanical properties. The thermodynamic properties of the PTC with DPMS under different boundary conditions were analyzed. The results show that the circumferential temperature difference of the new PTC is within 2.6 K, and the circumferential thermal deformation is within 0.9 mm under typical working conditions(the inlet velocity of the heat transfer fluid is 3 m/s, inlet temperature is 573.15 K, and the direct normal irradiance is 1000 W/m^(2)). Compared with conventional PTCs, the circumferential temperature difference is reduced by 74%–90%, and the maximum thermal deformation along the y-axis is reduced by more than 95% under all working conditions(1–5 m/s, 373.5–675.15 K, 200–1000 W/m^(2)). The new PTC maintains the uniformity of the circumferential solar flux distribution for different operating parameters(sun incident angle of 0°–3°) and installation errors(±3 mm), is suitable for solar energy applications in various fields, and has the potential for large-scale applications.

槽式光热电站大规模单回路管道施工技术

以某100MW槽式光热电站为背景,改进施工工序、研制安装工艺,进行管道组装、焊接和试压吹扫。采取化整为零,分环节批量作业的方式,有效保证了单回路管道安装的速度和质量;过程中通过各类创新与发明,以保证各最小单元焊接质量为基础,最终完成全部单回路管道安装。该技术为单回路管道安装创造了条件,大幅降低了光热电站建设的工期成本。

Comprehensive Review of Line-Focus Concentrating Solar Thermal Technologies: Parabolic Trough Collector (PTC) vs Linear Fresnel Reflector (LFR)

In the present review,parabolic trough collector(PTC)and linear Fresnel reflector(LFR)are comprehensively and comparatively reviewed in terms of historical background,technological features,recent advancement,economic analysis and application areas.It is found that although PTC and LFR are both classified as mainstream line-focus concentrating solar thermal(CST)technologies,they are now standing at different stages of development and facing their individual opportunities and challenges.For PTC,the development is commercially mature with steady and reliable performance;therefore,extension of application is the main future demand.For LFR,the development is still in rapid progress to commercial maturity,yet indicating very promising potentials with high flexibility in novel designs and remarkable reduction in capital and operational costs.The question,which has to be answered in order to estimate the future perspectives of these two line-focus CST technologies,becomes which of these characteristics carries more weight or how to reach an optimal trade-off between them.