10 × 10 Ga_(2)O_(3)-based solar-blind UV detector array and imaging characteristic

A 10 × 10 solar-blind ultraviolet(UV) imaging array with double-layer wire structure was prepared based on Ga_(2)O_(3) film grown by atomic layer deposition. These single detection units in the array exhibit excellent performance at 3 V: photo-todark current ratio(PDCR) of 5.5 × 10^(5), responsivity(R) of 4.28 A/W, external quantum efficiency(EQE) of 2.1 × 10^(3)%, detectivity(D*) of 1.5 × 10^(14) Jones, and fast response time. The photodetector array shows high uniformity under different light intensity and low operating bias. The array also has good temperature stability. Under 300 ℃, it still presents clear imaging and keeps high R of 34.4 and 6.45 A/W at 5 and 1 V, respectively. This work provides a new insight for the large-scale array of Ga_(2)O_(3) solarblind UV detectors.

Two-step growth of β-Ga_(2)O_(3) on c-plane sapphire using MOCVD for solar-blind photodetector

In this work,a two-step metal organic chemical vapor deposition(MOCVD)method was applied for growingβ-Ga_(2)O_(3) film on c-plane sapphire.Optimized buffer layer growth temperature(T_(B))was found at 700℃ and theβ-Ga_(2)O_(3) film with full width at half maximum(FWHM)of 0.66°was achieved.A metal−semiconductor−metal(MSM)solar-blind photodetector(PD)was fabricated based on theβ-Ga_(2)O_(3) film.Ultrahigh responsivity of 1422 A/W@254 nm and photo-to-dark current ratio(PDCR)of 10^(6) at 10 V bias were obtained.The detectivity of 2.5×10^(15) Jones proved that the photodetector has outstanding performance in detecting weak signals.Moreover,the photodetector exhibited superior wavelength selectivity with rejection ratio(R_(250 nm)/R_(400 nm))of 105.These results indicate that the two-step method is a promising approach for preparation of high-qualityβ-Ga_(2)O_(3)films for high-performance solar-blind photodetectors.

ZnO nanowires based degradable high-performance photodetectors for eco-friendly green electronics

Disposable devices designed for single and/or multiple reliable measurements over a short duration have attracted considerable interest recently. However, these devices often use non-recyclable and non-biodegradable materials and wasteful fabrication methods. Herein, we present ZnO nanowires(NWs) based degradable high-performance UV photodetectors(PDs) on flexible chitosan substrate. Systematic investigations reveal the presented device exhibits excellent photo response, including high responsivity(55 A/W), superior specific detectivity(4×10^(14) jones), and the highest gain(8.5×10~(10)) among the reported state of the art biodegradable PDs. Further, the presented PDs display excellent mechanical flexibility under wide range of bending conditions and thermal stability in the measured temperature range(5–50 ℃).The biodegradability studies performed on the device, in both deionized(DI) water(pH≈6) and PBS solution(pH=7.4),show fast degradability in DI water(20 mins) as compared to PBS(48 h). These results show the potential the presented approach holds for green and cost-effective fabrication of wearable, and disposable sensing systems with reduced adverse environmental impact.

Self-healing wearable self-powered deep ultraviolet photodetectors based on Ga_(2)O_(3)

Gallium oxide(Ga_(2)O_(3))based flexible heterojunction type deep ultraviolet(UV)photodetectors show excellent solar-blind photoelectric performance,even when not powered,which makes them ideal for use in intelligent wearable devices.How-ever,traditional flexible photodetectors are prone to damage during use due to poor toughness,which reduces the service life of these devices.Self-healing hydrogels have been demonstrated to have the ability to repair damage and their combination with Ga_(2)O_(3) could potentially improve the lifetime of the flexible photodetectors while maintaining their performance.Herein,a novel self-healing and self-powered flexible photodetector has been constructed onto the hydrogel substrate,which exhibits an excellent responsivity of 0.24 mA/W under 254 nm UV light at zero bias due to the built-in electric field originating from the PEDOT:PSS/Ga_(2)O_(3) heterojunction.The self-healing of the Ga_(2)O_(3) based photodetector was enabled by the reversible property of the synthesis of agarose and polyvinyl alcohol double network,which allows the photodetector to recover its original configu-ration and function after damage.After self-healing,the photocurrent of the photodetector decreases from 1.23 to 1.21μA,while the dark current rises from 0.95 to 0.97μA,with a barely unchanged of photoresponse speed.Such a remarkable recov-ery capability and the photodetector’s superior photoelectric performance not only significantly enhance a device lifespan but also present new possibilities to develop wearable and intelligent electronics in the future.

Improved Photoresponse of UV Photodetectors by the Incorporation of Plasmonic Nanoparticles on Ga N Through the Resonant Coupling of Localized Surface Plasmon Resonance

Very small metallic nanostructures,i.e.,plasmonic nanoparticles(NPs),can demonstrate the localized surface plasmon resonance(LSPR)e ect,a characteristic of the strong light absorption,scattering and localized electromagnetic field via the collective oscillation of surface electrons upon on the excitation by the incident photons.The LSPR of plasmonic NPs can significantly improve the photoresponse of the photodetectors.In this work,significantly enhanced photoresponse of UV photodetectors is demonstrated by the incorporation of various plasmonic NPs in the detector architecture.Various size and elemental composition of monometallic Ag and Au NPs,as well as bimetallic alloy Ag Au NPs,are fabricated on Ga N(0001)by the solid-state dewetting approach.The photoresponse of various NPs are tailored based on the geometric and elemental evolution of NPs,resulting in the highly enhanced photoresponsivity of 112 A W-1,detectivity of 2.4×1012 Jones and external quantum e ciency of 3.6×104%with the high Ag percentage of Ag Au alloy NPs at a low bias of 0.1 V.The Ag Au alloy NP detector also demonstrates a fast photoresponse with the relatively short rise and fall time of less than 160 and 630 ms,respectively.The improved photoresponse with the Ag Au alloy NPs is correlated with the simultaneous e ect of strong plasmon absorption and scattering,increased injection of hot electrons into the Ga N conduction band and reduced barrier height at the alloy NPs/Ga N interface.

Enhanced photoresponse performance in Ga/Ga_2O_3 nanocomposite solar-blind ultraviolet photodetectors

In the present work, we explore the solar-blind ultraviolet（UV） photodetectors（PDs） with enhanced photoresponse,fabricated on Ga/Ga2O3 nanocomposite films. Through pre-burying metal Ga layers and thermally post-annealing the laminated Ga2 O3/Ga/Ga2O3 structures, Ga/Ga2O3 nanocomposite films incorporated with Ga nanospheres are obtained. For the prototype PD, it is found that the photocurrent and photoresponsivity will first increase and then decrease monotonically with the thickness of the pre-buried Ga layer increasing. Each of all PDs shows a spectrum response peak at 260 nm, demonstrating the ability to detect solar-blind UV light. Adjustable photoresponse enhancement factors are achieved by means of the surface plasmon in the nanocomposite films. The PD with a 20 nm thick Ga interlayer exhibits the best solar-blind UV photoresponse characteristics with an extremely low dark current of 8.52 p A at 10-V bias, a very high light-to-dark ratio of ～ 8 × 10~5, a large photoresponsivity of 2.85 A/W at 15-V bias, and a maximum enhancement factor of ～ 220. Our research provides a simple and practical route to high performance solar-blind UV PDs and potential applications in the field of optoelectronics.

Ultraviolet photodetectors based on ferroelectric depolarization field

Ultraviolet(UV)photodetectors are extensively adopted in the fields of the Internet of Things,optical communications and imaging.Nowadays,with broadening the application scope of UV photodetectors,developing integrated devices with more functionalities rather than basic photo-detecting ability are highly required and have been triggered ever-growing interest in scientific and industrial communities.Ferroelectric thin films have become a potential candidate in the field of UV detection due to their wide bandgap and unique photovoltaic characteristics.Additionally,ferroelectric thin films perform excellent dielectric,piezoelectric,pyroelectric,acousto-optic effects,etc.,which can satisfy the demand for the diversified development of UV detectors.In this review,according to the different roles of ferroelectric thin films in the device,the UV photodetectors based on ferroelectric films are classified into ferroelectric depolarization field driven type,ferroelectric depolarization field and built-in electric field co-driven type,and ferroelectric field enhanced type.These three types of ferroelectric UV photodetectors have great potential and are expected to promote the development of a new generation of UV detection technology.At the end of the paper,the advantages and challenges of three types of ferroelectric UV photodetectors are summarized,and the possible development direction in the future is proposed.

Preparation of Ga_2O_3 thin film solar-blind photodetectors based on mixed-phase structure by pulsed laser deposition

Gallium oxide(Ga_2O_3) thin films were deposited on a-Al2O3(1120) substrates by pulsed laser deposition(PLD) with different oxygen pressures at 650?C. By reducing the oxygen pressure, mixed-phase Ga_2O_3 films with α and β phases can be obtained, and on the basis of this, mixed-phase Ga_2O_3 thin film solar-blind photodetectors(SBPDs) were prepared.Comparing the responsivities of the mixed-phase Ga_2O_3 SBPDs and the single β-Ga_2O_3 SBPDs at a bias voltage of 25 V,it is found that the former has a maximum responsivity of approximately 12 A/W, which is approximately two orders of magnitude larger than that of the latter. This result shows that the mixed-phase structure of Ga_2O_3 thin films can be used to prepare high-responsivity SBPDs. Moreover, the cause of this phenomenon was investigated, which will provide a feasible way to improve the responsivity of Ga_2O_3 thin film SBPDs.

Facile fabrication of heterostructure with p-BiOCl nanoflakes and n-ZnO thin film for UV photodetectors

Herein, high-quality n-ZnO film layer on c-sapphire and well-crystallized tetragonal p-BiOCl nanoflakes on Cu foil are prepared, respectively. According to the absorption spectra, the bandgaps of n-ZnO and p-BiOCl are confirmed as ~3.3 and~3.5 eV, respectively. Subsequently, a p-BiOCl/n-ZnO heterostructural photodetector is constructed after a facile mechanical bonding and post annealing process. At –5 V bias, the photocurrent of the device under 350 nm irradiation is ~800 times higher than that in dark, which indicates its strong UV light response characteristic. However, the on/off ratio of In–ZnO–In photodetector is ~20 and the Cu–BiOCl–Cu photodetector depicts very weak UV light response. The heterostructure device also shows a short decay time of 0.95 s, which is much shorter than those of the devices fabricated from pure ZnO thin film and BiOCl nanoflakes. The p-BiOCl/n-ZnO heterojunction photodetector provides a promising pathway to multifunctional UV photodetectors with fast response, high signal-to-noise ratio, and high selectivity.

Recent advances in Ga-based solar-blind photodetectors

Solar-blind ultraviolet photodetectors have many advantages, such as low false alarm rates, the ability to detect weak signals, and high signal-to-noise ratios. Among the various functional solar-blind ultraviolet photodetectors, Ga-based alloys of AlGaN and Ga_2O_3 are the most commonly adopted channel semiconductor materials and have attracted extensive research attention in the past decades. This review presents an overview of the recent progress in Ga-based solar-blind photodetectors. In case of AlGaN-based solar-blind ultraviolet photodetectors, the response properties can be improved by optimizing the AlN nucleation layer and designing the avalanche structure. On the other hand, we also discuss the morphology and growth methods of Ga_2O_3 nanomaterials and their effect on the performance of the corresponding solarblind photodetectors. The mechanically exfoliated Ga_2O_3 flakes show good potential for ultraviolet detection. Also, Ga_2O_3 nanoflowers and nanowires reveal perfect response to ultraviolet light. Finally, the challenges and future development of Ga-based functional solar-blind ultraviolet photodetectors are summarized.

Fast-speed self-powered PEDOT:PSS/α-Ga_(2)O_(3)nanorod array/FTO photodetector with solar-blind UV/visible dual-band photodetection

Theα-Ga2 O_(3)nanorod array is grown on FTO by hydrothermal and annealing processes.And a self-powered PEDOT:PSS/α-Ga_(2)O_(3)nanorod array/FTO(PGF)photodetector has been demonstrated by spin coating PEDOT:PSS on theα-Ga_(2)O_(3)nanorod array.Successfully,the PGF photodetector shows solar-blind UV/visible dual-band photodetection.Our device possesses comparable solar-blind UV responsivity(0.18 mA/W at 235 nm)and much faster response speed(0.102 s)than most of the reported self-poweredα-Ga_(2)O_(3)nanorod array solar-blind UV photodetectors.And it presents the featured and distinguished visible band photoresponse with a response speed of 0.136 s at 540 nm.The response time is also much faster than the other non-self-poweredβ-Ga_(2)O_(3)DUV/visible dual-band photodetectors due to the fast-speed separation of photogenerated carries by the built-in electric field in the depletion regions of PEDOT:PSS/α-Ga_(2)O_(3)heterojunction.The results herein may prove a promising way to realize fast-speed self-poweredα-Ga_(2)O_(3)photodetectors with solar-blind UV/visible dual-band photodetection by simple processes for the applications of multiple-target tracking,imaging,machine vision and communication.

A Solar-Blind AlGaN-Based p-i-n Back-Illuminated Photodetector with a High Temperature AlN Template Layer

The growth, fabrication, and characterization of a solar-blind A1GaN-based p-i-n back-illuminated photodetector with a high temperature A1N template are reported for the first time. The photodetector was fabricated from multilayer AIx Gal-xN films grown by MOCVD on double-polished c-plane （0001） sapphire substrates. Crack free, high A1 content （0.7） A1GaN multilayer structure,designed for the solar-blind p-i-n back-illuminated photodetector,was grown on a high temperature A1N template without a nuclear layer. The high quality of the epitaxial layers is demonstrated by in-situ optical reflectance monitoring curve, triple-axis X-ray diffraction, and atomic-force microscope. At a 1.8V bias, the processed p-i-n photodetector exhibits a solar-blind photoresponse with a maximum responsivity of 0. 0864A/W at 270nm. The photodetector exhibits a forward turn-on voltage at around 3.5V and a reverse breakdown voltage above 20V, and the leakage current is below 20pA for 2V reverse bias.

Multifunctional solar-blind ultraviolet photodetectors based on p-PCDTBT/n-Ga_(2)O_(3)heterojunction with high photoresponse

Solar-blind ultraviolet(UV)photodetectors based on p-organic/n-Ga_(2)O_(3) hybrid heterojunctions have attracted extensive attention recently.Herein,the multifunctional solar-blind photodetector based on p-type poly[N-90-heptadecanyl-2,7-carbazole-alt-5,5-(40,70-di-2-thienyl-20,10,30-benzothiadiazole)](PCDTBT)/n-type amorphous Ga_(2)O_(3)(a-Ga_(2)O_(3))is fabricated and investigated,which can work in the phototransistor mode coupling with self-powered mode.With the introduction of PCDTBT,the dark current of such the a-Ga_(2)O_(3)-based photodetector is decreased to 0.48 pA.Meanwhile,the photoresponse parameters of the a-Ga_(2)O_(3)-based photodetector in the phototransistor mode to solar-blind UV light are further increased,that is,responsivity(R),photo-detectivity(D*),and external quantum efficiency(EQE)enhanced to 187 A W^(-1),1.3×10^(16) Jones and 9.1×10^(4)% under the weak light intensity of 11μW cm^(-2),respectively.Thanks to the formation of the built-in field in the p-PCDTBT/n-Ga_(2)O_(3) type-Ⅱ heterojunction,the PCDTBT/Ga_(2)O_(3) multifunctional photodetector shows self-powered behavior.The responsivity of p-PCDTBT/n-Ga_(2)O_(3) multifunctional photodetector is 57.5 mA W^(-1) at zero bias.Such multifunctional p-n hybrid heterojunction-based photodetectors set the stage for realizing high-performance amorphous Ga_(2)O_(3) heterojunction-based photodetectors.

Enhanced back-illuminated Ga_(2)O_(3)-based solar-blind ultraviolet photodetectors

Ga_(2)O_(3)is a promising material for deep-ultraviolet(DUV)photodetectors due to its ultra-wide bandgap and high thermal and chemical stability.However,because of their relatively low responsivity,Ga_(2)O_(3)-based photodetectors still have difficulty meeting the requirements of practical applications.Here,we construct a high-performance Ga_(2)O_(3)photodetector realized by back-illumination.Utilizing high-crystallinity epitaxially grown Ga_(2)O_(3)as the DUV absorbing layer and the double-polished Al_(2)O_(3)substrate as the transparent window for injection of photons,the device operating in the back-illuminated mode exhibits a higher DUV photoresponse and faster response speed than in the front-illuminated mode.Therefore,our experimental results have led to the development of a novel strategy for designing and fabricating high-performance Ga_(2)O_(3)photodetectors.

Three-dimensional porous In_(2)O_(3) arrays for self-powered transparent solar-blind photodetectors with high responsivity and excellent spectral selectivity

Transparent solar-blind ultraviolet photodetectors(SBUV PDs)have extensive applications in versatile scenarios,such as optical communication.However,it is still challenging to simultaneously achieve high responsivity,high transparency,and satisfying self-powered capability.Here,we demonstrated high-performance,transparent,and self-powered photoelectrochemical-type(PEC)SBUV PDs based on vertically grown ultrathin In_(2)O_(3) nanosheet arrays(NAs)with a three-dimensional(3D)porous structure.The 3D porous structure simultaneously improves the transmittance in the visible light region,accelerates interfacial reaction kinetics,and promotes photogenerated carrier transport.The performance of In_(2)O_(3) NAs photoanodes exceeds most reported self-powered PEC SBUV PDs,exhibiting a high transmittance of approximately 80%in the visible light region,a high responsivity of 86.15 mA/W for 254 nm light irradiation,a fast response speed of 15/18 ms,and good multicycle stability.The In_(2)O_(3) NAs also show excellent spectral selectivity with an ultrahigh solar-blind rejection ratio of 1319.30,attributed to the quantum confinement effect induced by the ultrathin feature(2-3 nm).Furthermore,In_(2)O_(3) NAs photoanodes show good capability in underwater optical communication.Our work demonstrated that a 3D porous structure is a powerful strategy to synchronously achieve high responsivity and transparency and provides a new perspective for designing high-performance,transparent,and self-powered PEC SBUV PDs.

Investigation into epitaxial growth optimization of a novel AlGaN/GaN HEMT structure for application in UV photodetectors

In this work,a novel ultraviolet(UV)photodetector(PD)based on AlGaN/u-GaN/p-GaN/u-GaN heterojunction high electron mobility transistor(HEMT)has been developed.This HEMT epilayer is grown using the metal-organic chemical vapor deposition(MOCVD)technique,and the growth parameters,including the AlGaN growth temperature,preheating temperature of the p-GaN layer,and NH3/N2 flow rate,are optimized to improve the quality of the epilayer.The optimized epilayer exhibits a flat surface with a root mean square value of 0.146 nm and low dislocation density.The p-GaN thickness in epitaxial wafers has a significant influence on electrical and UV photoresponse.With a p-GaN of 1µm,the UV PD demonstrates a significant switching ratio and transconductance of 107 and 127.3 mS mm^(-1),respectively.Acting as a UV PD,it also exhibits a high light on/off ratio(I_(light)/I_(dark))of 6.35×10^(5),a high responsivity(R)of 48.11 A W^(-1),and a detectivity(D*)of 6.85×10^(12)Jones under 365-nm UV illumination with light power density of 86.972 mW cm^(-2).The high-performance HEMT and UV detectors,which incorporate p-GaN etchless technology,have been refined through advancements in epitaxial growth and structural design.These improvements solidify the groundwork for large-scale manufacturing of UV communication systems and laser diodes.

Effect of temperature on photoresponse properties of solar-blind Schottky barrier diode photodetector based on single crystal Ga_2O_3

A solar-blind photodetector is fabricated on single crystal Ga_2O_3 based on vertical structure Schottky barrier diode. A Cu Schottky contact electrode is prepared in a honeycomb porous structure to increase the ultraviolet(UV) transmittance.The quantum efficiency is about 400% at 42 V. The Ga_2O_3 photodetector shows a sharp cutoff wavelength at 259 nm with high solar-blind/visible(= 3213) and solar-blind/UV(= 834) rejection ratio. Time-resolved photoresponse of the photodetector is investigated at 253-nm illumination from room temperature(RT) to 85.8℃. The photodetector maintains a high reversibility and response speed, even at high temperatures.

A theoretical and experimental evaluation of Ⅲ–nitride solar-blind UV photocathode

We have developed a superior solar-blind ultraviolet （UV） photocathode with an AlxGa1_xrN photocathode （x ～ 0.45） in semi-transparent mode, and assessed spectra radiant sensitivity related to practical use. Betbre being grown over a basal plane sapphire substrate by low-pressure metal organic chemical vapor deposition （MOCVD）, a reasonable design was made to the photocathode epitaxy structure, focusing on the AlxGa1_xN： Mg active layer, then followed by a comprehen- sive analysis of the structural and optical characterization. The spectra radiant sensitivity is peaked of 41.395 mA/W at wavelength 257 nm and then decreases by about 3 to 4 decades at 400 nm demonstrating the ability of this photocathode for solar-blind application prospects.

Optical Field Confinement Enhanced Single ZnO Microrod UV Photodetector

ZnO microrods are synthesized using the vapor phase transport method, and the magnetron sputtering is used to decorate the A1 nanoparticles （NPs） on a single ZnO microrod. The micro-PL and I-V responses are measured before and after the decoration orAl NPs. The FDTD stimulation is also carried out to demonstrate the optical field distribution around the decoration of Al NPs on the surface of a ZnO microrod. Due to an implementation of AI NPs, the ZnO microrod exhibits an improved photoresponse behavior. In addition, AI NPs induced localized surface plasmons （LSPs） as well as improved optical field confinement can be ascribed to an enhancement of ultraviolet （UV） response. This research provides a method for improving the responsivity of photodetectors.

The simulation of temperature dependence of responsivity and response time for 6H-SiC UV photodetector

In this paper the temperature dependence of responsivity and response time for 6H-SiC ultraviolet （UV） photodetector is simulated based on numerical model in the range from 300 K to 900 K. The simulation results show that the responsivity and the response time of device are less sensitive to temperature and this kind of UV photodetector has excellent temperature stability. Also the effects of device structure and bias voltage on the responsivity and the response time are presented. The thicker the drift region is, the higher the responsivity and the longer the response time are. So the thickness of drift region has to be carefully designed to make trade-off between responsivity and response time.