Investigation on plume interference effect of solid propellant micro-thruster

The three-dimensional numerical simulation of two-phase plume flow of solid propellant micro-thrusters was developed.Then it was used to investigate the plume interference effect by combining the direct simulation Monte Carlo(DSMC) method for multi-component gas flow with the two-way coupling model for two-phase rarefied flow.At different space between the two micro-thrusters and different wall temperature,the plume interference effect was analyzed specifically.The results show that under the plume interference effect the gas is compressed and the flow direction is changed,which resulted in the increasing of gas pressure and temperature;solid phase made no significant effect on the flow parameters of gas phase;with the rising of the space between the two micro-thrusters,the maximum pressure decreased and the maximum temperature increased in the domain under the plume interference effect;the wall temperature could influence the temperature of the gas which is extremely close to the wall,but not the gas pressure.

Effect of neutral polymeric bonding agent on tensile mechanical properties and damage evolution of NEPE propellant

Introducing Neutral Polymeric bonding agents(NPBA) into the Nitrate Ester Plasticized Polyether(NEPE)propellant could improve the adhesion between filler/matrix interface, thereby contributing to the development of new generations of the NEPE propellant with better mechanical properties. Therefore,understanding the effects of NPBA on the deformation and damage evolution of the NEPE propellant is fundamental to material design and applications. This paper studies the uniaxial tensile and stress relaxation responses of the NEPE propellant with different amounts of NPBA. The damage evolution in terms of interface debonding is further investigated using a cohesive-zone model(CZM). Experimental results show that the initial modulus and strength of the NEPE propellant increase with the increasing amount of NPBA while the elongation decreases. Meanwhile, the relaxation rate slows down and a higher long-term equilibrium modulus is reached. Experimental and numerical analyses indicate that interface debonding and crack propagation along filler-matrix interface are the dominant damage mechanism for the samples with a low amount of NPBA, while damage localization and crack advancement through the matrix are predominant for the ones with a high amount of NPBA. Finally, crosslinking density tests and simulation results also show that the effect of the bonding agent is interfacial rather than due to the overall crosslinking density change of the binder.

Experimental study of Al agglomeration on solid propellant burning surface and condensed combustion products

Aluminum(Al) particles are commonly added to energetic materials including propellants,explosives and pyrotechnics to increase the overall energy density of the composite,but aluminum agglomeration on the combustion surface may lower the combustion efficiency of propellants,resulting in a loss in twophase flow.Therefore,it is necessary to understand the agglomeration mechanism of aluminum particles on the combustion surface.In this paper,a high-pressure sealed combustion chamber is constructed,and high-speed camera is used to capture the whole process of aluminum accumulation,aggregation and agglomeration on the combustion surface,and the secondary agglomeration process near the combustion surface.The microscopic morphology and chemical composition of the condensed combustion products(CCPs) are then studied by using scanning electron microscopy coupled with energy dispersive(SEM-EDS) method.Results show that there are three main types of condensed combustion products:small smoke oxide particles oxidized by aluminum vapor,usually less than 1 μm;typical agglomerates formed by the combustion of aluminum agglomerates;carbonized agglomerates that are widely distributed,usually formed by irregular movements of aluminum agglomerates.The particle size of condensed combustion products is measured by laser particle size meter.As the pressure increases from 0.5 MPa to 1.0 MPa in nitrogen,the mass average particle size of aluminum agglomerates decreases by 49.7%.As the ambient gas is changed from 0.5 MPa nitrogen to 0.5 MPa air,the mass average particle size of aluminum agglomerates decreases by 67.3%.Results show that as the ambient pressure increases,the higher oxygen content can improve combustion efficiency and reduce the average agglomeration size of aluminum particles.

Strength criterion of composite solid propellants under dynamic loading

Based on the dynamic loading(1-100 s^(-1)) experiments under different temperatures(223-298 K) and stress states, uniaxial and biaxial strength criterion of a Hydroxyl-terminated polybutadiene(HTPB)based composite solid propellant were further investigated. These experiments were conducted through the use of a new uniaxial INSTRON testing machine, different new designed gripping apparatus and samples with different configurations. According to the test results, dynamic uniaxial tensile strength criterion of the propellant was directly constructed with the master curve of the uniaxial maximum tensile stress. Whereas, a new method was proposed to determine the dynamic uniaxial compressive strength of the propellant in this study. Then uniaxial compressive strength criterion of the propellant was constructed based on the related master curve. Moreover, it found that the uniaxial tensilecompressive strength ratio of the propellant is more sensitive to loading temperature under the test conditions. The value of this parameter is about 0.4 at room temperature, and it reduces to 0.2-0.3 at low temperatures. Finally, the theoretical biaxial strength criterion of HTPB propellant under dynamic loading was constructed with the unified strength theory, the uniaxial strength and the typical biaxial tensile strength. In addition, the theoretical limit lines of the principal stress plane for the propellant under dynamic loading at different temperatures were further plotted, and the scope of the limit line increases with decreasing temperature.

Recent advances in catalytic combustion of AP-based composite solid propellants

Composite solid propellants(CSPs) have widely been used as main energy source for propelling the rockets in both space and military applications. Internal ballistic parameters of rockets like characteristic exhaust velocity, specific impulse, thrust, burning rate etc., are measured to assess and control the performance of rocket motors. The burn rate of solid propellants has been considered as most vital parameter for design of solid rocket motors to meet specific mission requirements. The burning rate of solid propellants can be tailored by using different constituents, extent of oxidizer loading and its particle size and more commonly by incorporating suitable combustion catalysts. Various metal oxides(MOs),complexes, metal powders and metal alloys have shown positive catalytic behaviour during the combustion of CSPs. These are usually solid-state catalysts that play multiple roles in combustion of CSPs such as reduction in activation energy, enhancement of rate of reaction, modification of sequences in reaction-phase, influence on condensed-phase combustion and participation in combustion process in gas-phase reactions. The application of nanoscale catalysts in CSPs has increased considerably in recent past due to their superior catalytic properties as compared to their bulk-sized counterparts. A large surface-to-volume ratio and quantum size effect of nanocatalysts are considered to be plausible reasons for improving the combustion characteristics of propellants. Several efforts have been made to produce nanoscale combustion catalysts for advanced propellant formulations to improve their energetics. The work done so far is largely scattered. In this review, an effort has been made to introduce various combustion catalysts having at least a metallic entity. Recent developments of nanoscale combustion catalysts with their specific merits are discussed. The combustion chemistry of a typical CSP is briefly discussed for providing a better understanding on role of combustion catalysts in burning rate enhancement. Available information on different types of combustion nanocatalysts is also presented with critical comments.

Cu–Co–O nano-catalysts as a burn rate modifier for composite solid propellants

Nano-catalysts containing copper–cobalt oxides(Cu–Co–O) have been synthesized by the citric acid(CA) complexing method. Copper(II) nitrate and Cobalt(II) nitrate were employed in different molar ratios as the starting reactants to prepare three types of nano-catalysts. Well crystalline nano-catalysts were produced after a period of 3 hours by the calcination of CA–Cu–Co–O precursors at 550 °C. The phase morphologies and crystal composition of synthesized nano-catalysts were examined using Scanning Electron Microscope(SEM), Energy Dispersive Spectroscopy(EDS) and Fourier Transform Infrared Spectroscopy(FTIR) methods. The particle size of nano-catalysts was observed in the range of 90 nm–200 nm. The prepared nano-catalysts were used to formulate propellant samples of various compositions which showed high reactivity toward the combustion of HTPB/AP-based composite solid propellants. The catalytic effects on the decomposition of propellant samples were found to be significant at higher temperatures. The combustion characteristics of composite solid propellants were significantly improved by the incorporation of nano-catalysts. Out of the three catalysts studied in the present work, Cu Co-I was found to be the better catalyst in regard to thermal decomposition and burning nature of composite solid propellants. The improved performance of composite solid propellant can be attributed to the high crystallinity, low agglomeration and lowering the decomposition temperature of oxidizer by the addition of Cu Co-I nano-catalyst.

Estimation of the Ballistic Effectiveness of 3,4-and 3,5-Dinitro-1-(trinitromethyl)-1H-Pyrazoles as Oxidizers for Composite Solid Propellants

The experimental values of the enthalpy of formation of two isomeric 3,4-and 3,5-dinitro-1-(trinitromethyl)-1H-pyrazoles have been obtained(261.5±5.0and 246.4±6.7kJ/mol for crystalline 3,4-and 3,5-dinitro-1-(trinitromethyl)-1H-pyrazoles,respectively).The ballistic effectiveness of these potential oxidizers in composite solid propellants was studied.It is shown that these two oxidizers may be successfully applied in metal-free compositions or with a small content of metal.For the bottom stage 3,4-dinitro-1-(trinitromethyl)-1H-pyrazole is a bit better than 3,5-dinitro-1-(trinitromethyl)-1H-pyrazole,for the upper stage the both oxidizers show the equal ballistic parameters.These oxidizers allow to create metal-free solid composite propellants with the binder percentage not lower than 19%(volume fraction),with I3spequal to 256.5-257.0sat density equal to 1.72-1.74g/cm^3.

Controllable combustion behaviors of the laser-controlled solid propellant

Microsatellites have been widely applied in the fields of communication,remote sensing,navigation and science exploration due to its characteristics of low cost,flexible launch mode and short development period.However,conventional solid-propellant have difficulties in starting and interrupting combustion because combustion is autonomously sustained after ignition Herein,we proposed a new type of solid-propellant named laser-controlled solid propellant,which is sensitive to laser irradiation and can be started or interrupted by switching on/off the continuous wave laser.To demonstrate the feasibility and investigate the controllable combustion behaviors under different laser on/off conditions,the combus tion parameters including burning rate,ignition delay time and platform pressure were tested using pressure sensor,high-speed camera and thermographic camera.The results showed that the increase of laser-on or laser-off duration both will lead to the decrease of propellant combustion performance during re-ignition and re-combustion process.This is mainly attributed to the laser attenuation caused by the accumulation of combustion residue and the change of chamber ambient temperature.Simultaneously the multiple ignition tests revealed that the increased chamber ambient temperature after combustion can make up for the energy loss of laser attenuation and expansion of chamber cavity.However,the laser-controlled combustion performance of solid propellant displayed a decrease trend with the addi-tion of ignition times.Nevertheless,the results still exchibited good laser-controlled agility of laser-controlled solid propellant and manifested its inspiring potential in many aspects of space missions.

Improvement in Time Efficiency in Numerical Simulation for Solid Propellant Rocket Motors(SPRM)

The main purpose of the present work is to study the possibilities of reducing calculation time while maintaining the validity in the numerical simulation of the combustion product flow in SPRM chamber.Three ways of decreasing the calculation time-the use of numerical methods of high accuracy order,the reduction in spatial dimension of the problem,and the use of physical features of the processes in SPRM chamber while constructing a calculation model-were considered.Presented calculation data show that the use of these approaches makes it possible to reduce the time for solving the problems of SPRM simulation significantly(up to 100times).Also conclusions about the applicability of the mentioned above approaches in SPRM design were made.

The properties of Sn-Zn-Al-La fusible alloy for mitigation devices of solid propellant rocket motors

The Al and La elements are added to the Sn9Zn alloy to obtain the fusible alloy for the mitigation devices of solid propellant rocket motors. Differential scanning calorimetry(DSC), metallographic analysis,scanning electron microscopy(SEM), energy dispersive spectroscopy(EDS), tensile testing and fracture analysis were used to study the effect of Al and La elements on the microstructure, melting characteristics, and mechanical properties of the Sn9Zn alloy. Whether the fusible diaphragm can effectively relieve pressure was investigated by the hydrostatic pressure at high-temperature test. Experimental results show that the melting point of the Sn9Zn-0.8Al0·2La and Sn9Zn-3Al0·2La fusible alloys can meet the predetermined working temperature of ventilation. The mechanical properties of those are more than 35% higher than that of the Sn9Zn alloy at-50°C-70°C, and the mechanical strength is reduced by 80% at 175°C. It is proven by the hydrostatic pressure at high-temperature test that the fusible diaphragm can relieve pressure effectively and can be used for the design of the mitigation devices of solid propellant rocket motors.

Application of transient burning rate model of solid propellant in electrothermal-chemical launch simulation

A 30 mm electrothermal-chemical(ETC) gun experimental system is employed to research the burning rate characteristics of 4/7 high-nitrogen solid propellant. Enhanced gas generation rates(EGGR) of propellants during and after electrical discharges are verified in the experiments. A modified 0D internal ballistic model is established to simulate the ETC launch. According to the measured pressure and electrical parameters, a transient burning rate law including the influence of EGGR coefficient by electric power and pressure gradient(dp/dt) is added into the model. The EGGR coefficient of 4/7 high-nitrogen solid propellant is equal to 0.005 MW-1. Both simulated breech pressure and projectile muzzle velocity accord with the experimental results well. Compared with Woodley's modified burning rate law, the breech pressure curves acquired by the transient burning rate law are more consistent with test results. Based on the parameters calculated in the model, the relationship among propellant burning rate, pressure gradient(dp/dt) and electric power is analyzed. Depending on the transient burning rate law and experimental data, the burning of solid propellant under the condition of plasma is described more accurately.

Effects of Metal and Composite Metal Nanopowders on the Thermal Decomposition of Ammonium Perchlorate (AP) and the Ammonium Perchlorate/Hydroxyterminated Polybutadiene (AP/HTPB) Composite Solid Propellant

Effects of metal (Ni, Cu, Al) and composite metal (NiB, NiCu, NiCuB) nanopowders on the thermal decomposition of ammonium perchlorate (AP) and composite solid propellant ammonium perchlorate/hydroxyterminated polybutadiene (AP/HTPB) were studied by thermal analysis (DTA). The results show that metal and composite metal nanopowders all have good catalytic effects on the thermal decomposition of AP and AP/HTPB composite solid propellant. The effects of metal nanopowders on the thermal decomposition of AP are less than those of the composite metal nanopowders. The effects of metal and composite metal nanopowders on the thermal decomposition of AP are different from those on the thermal decomposition of the AP/HTPB composite solid propellant.

Safety analysis on truing process of solid propellant

In order to investigate safety character of solid propellant, the truing process was analyzed by a thermalmechanical coupled finite element method. Based on the viscoelastic integral constitutive relation, the temperature response in truing process was calculated. The result showed that the maximum temperature in solid propellant truing process could attain up to 65 ℃ when the truing velocity was 10 mm/s and the truing thickness was 1 mm, and there was no remarkable temperature change under the truing thickness of 1.0 mm, 1.5 mm and 2.5 mm. The hazard in truing process of solid propellant was mainly close to the edge of cutting area.

Energetic Abilities of Solid Composite Propellants Based on 3,4,5-Trinitropyrazole and Ammonium Dinitramide

The investigation aims at the expansion of the basis of formulations of solid composite propellants by introducing new compositions with lower sensitivity to mechanic impact and improved thermal stability.The formulations based on trinitropyrazole(TNP)contains a binder(a hydrocarbon or active one),aluminum and inorganic oxidizer ADN.The results show that a binary formulation TNP+active binder(18%-19%)(volume fraction)with no metal is well designed which would achieve high specific impulse(at Pc∶Pa=40∶1)of 248s,high density of 1.80g/cm3 and combustion temperature Tcabout 3 450K.In terms of energy,metal-free compositions with TNP lose a bit to those with HMX,only if HMX fraction in formulation is higher than 45%-50%.

Study on the Detonation Danger of Solid Propellants

A measurement system to study shock initiation behavior of solid propellants was established experimentally. By using this system, the study on shock initiation to the recovered solid propellants with micro damage was performed, especially on the deflagration to denonation transition (DDT) process of solid propellants under both the strong and weak conditions of restriction. The experimental results show that there is a fully compression region in DDT process..

Effects of Plasticizers,Antioxidants and Burning Rate Modifiers on Aging Performance of the HTPB/HMDI Composite Solid Propellant

The effects of plasticizers,antioxidants and burning rate modifiers on the aging performance of the composite solid propellant based on hydroxyl-terminated polybutadiene(HTPB)/hexamethylene diisocyanate(HMDI)were explored by apply-ing an accelerated aging program for 90 day at 70 ℃. The HTPB propellant matrix with the diisooctyl sebacate(DOS)as plasti-cizers and diisooctyl azelate(DOZ), antioxidants as N,N ′-Diphenyl-p-phenylenediamine(AO) and 2,2′-methylenebis(4-methyl-6-tert-butylphenol)(cyanox 2246)and burning rate modifiers as barium ferrite(BF),copper chromites(CC)and fer-ric oxide(FO)were varied. Results show that sample(S1)which based on DOS decreases the stress value and increases the strain value which considered to be an excellent start for aging program. Sample(S3)containing AO presents the higher resis-tance to oxidation showing the better performance that reflects on increasing the shelf life of the composite solid propellant mo-tor. Sample(S5)which based on BF enhances the ballistic performance among over the other tested two samples. The accelerat-ed aging program allowed us to estimate the motor in-service lifetime.

Experimental Investigation on Combustion Performance of Solid Propellant Subjected to Erosion of Particles with Different Concentrations

A test device with rectangular channel is developed to study the combustion performance of solid propellant in high temperature particles erosion.The flowfields in this newdevice and a test device with circular channels are simulated numerically.The particle erosion experiments in these two devices are carried out under different particle concentrations.The results showthat the test device with rectangular channel can effectively improve the clarity and precision of combustion diagnosis image and can be used for research on combustion performance of solid propellant under lowconcentration particle erosion;the circular channel device has good particle convergent effect,provides high concentration particle erosion,and can be used for research on the combustion performance of solid propellant under high concentration particle erosion.The experiment data indicates that the propellant burning rate does not change obviously in lower particle concentration;the propellant with lower static burning rate increases remarkably under particle erosion,while the propellant with high static burning rate is not sensitive to the particle erosion.

Energetic Opportunities of Solid Composite Propellants Containing Some Hypothetic Furazano-[3,4-d]-pyridazine-based Derivatives

Six furazano-[3,4-d]-pyridazine-based derivatives as main compounds in solid composite propellants have been investigated.It was shown that the use of some furazano-[3,4-d]-pyridazine-based derivatives as main compounds in solid composite propellants can considerably increase ballistic parameters compared with HMX if the compounds under consideration contain difluoramine groups.And the use of the compounds under consideration may be successful only in the presence of an active binder and 10%-30% of AP or ADN as additional oxidizers.

The Influence of Aziridine on the Aging of Composite Solid Rocket Propellant

Aging of a solid composite propellant containing HTPB/AP/AL was performed in order to validate the conformance of the accelerated aging data to the Arrhenius law. The main objective of the work was to examine the influence of the aziridine bonding agents family on the propellant aging. Aging of the prepared propellant samples was conducted as follows: 1. Four samples, one free of bonding agents, and three containing aziridine based bonding agents MAPO,HX-752, MAT4 were aged at 65°C. 2. Another four samples based on HX-752, MAT4 with different curing agents were aged at 65°C. The measured mechanical properties of the free bonding agent propellant samples were very far from the specifications and this illustrates the importance of the bonding agents in both the preparation and the aging phases.The prepared bonding agent 'MAT4' gave remarkable improvements of the mechanical properties comparing with HX-752 and MAPO. The aziridine bonding agents family inhibited the rate of decomposition of the propellant during the aging periods and supported the propellant matrix against decomposition at the elevate temperatures. Using of HMDI as curing agent gave slight better mechanical properties to the IPDI.

Multiscale modeling of heterogeneous propellants from particle packing tograin failure using a surface-based cohesive approach

In the present work, a computational frame- work is established for multiscale modeling and analysis of solid propellants. A packing algorithm, considering the am- monium perchlorate （AP） and aluminum （A1） particles as spheres or discs is developed to match the size distribution and volume fraction of solid propellants. A homogenization theory is employed to compute the mean stress and strain of a representative volume element （RVE）. Using the mean results, a suitable size of RVE is decided. Without consider- ing the interfaces between particles and matrix, several nu- merical simulations of the relaxation of propellants are per- formed. The relaxation effect and the nonlinear mechanical behavior of propellants which are dependent on the applied loads are discussed. A new technology named surface-based cohesive behavior is proposed to describe the phenomenon of particle dewetting consisting of two ingredients： a damage initiation criterion and a damage evolution law. Several ex- amples considering contact damage behavior are computed and also nonlinear behavior caused by damaged interfaces is discussed in this paper. Furthermore the effects of the criti- cal contact stress, initial contact stiffness and contact failure distance on the damaged interface model have been studied.