Effects of antibiotics on corncob supported solid-phase denitrification: Denitrification and antibiotics removal performance, mechanism, and antibiotic resistance genes

Solid-phase denitrification(SPD)has been used in wastewater treatment plant effluent to enhance nitrate removal,and antibiotics co-existing in the effluent is a common environmental problem.In this study,it was systematically investigated the effect of single trace sulfamethoxazole(SMX)/trimethoprim(TMP)and theirmixture on microbial denitrification performance,the antibiotics removal,and antibiotics resistance genes(ARGs)in corncob supported SPD system.The average denitrification rate was improved by 46.90%or 61.09%with single 50μg/L SMX or TMP,while there was no significant inhibition with mixed SMX and TMP.The abundance of dominant denitrifiers(Comamonadaceae family and Azospia)and fermentation bacteria(Ancalomicrobium)were consistent with the denitrification performance of different antibiotics groups.Single SMX and TMP achieved relatively higher denitrification gene and enzyme abundance.Mixed SMX and TMP improved the denitrification gene copies,but they reduced the key denitrification enzymes except for EC 1.7.7.2.Additionally,the removal efficiency of TMP(56.70%±3.18%)was higher than that of SMX(25.44%±2.62%)in single antibiotic group,and the existence of other antibiotics(i.e.SMX or TMP)had no significant impact on the TMP or SMX removal performance.Biodegradation was the main removal mechanism of SMX and TMP,while sludge and corncob adsorption contributed a little to their removal.SMX had the risk of sulfanilamide resistance genes(SRGs)dissemination.Furthermore,network analysis indicated that Niveibacterium and Bradyrhizobium were the potential hosts of SRGs,which promoted the horizontal transmission of ARGs.

Solid-phase microextraction of endogenous metabolites from intact tissue validated using a Biocrates standard reference method kit

Improved analytical methods for the metabolomic profiling of tissue samples are constantly needed.Currently,conventional sample preparation methods often involve tissue biopsy and/or homogenization,which disrupts the endogenous metabolome.In this study,solid-phase microextraction(SPME)fibers were used to monitor changes in endogenous compounds in homogenized and intact ovine lung tissue.Following SPME,a Biocrates AbsoluteIDQ assay was applied to make a downstream targeted metabolomics analysis and confirm the advantages of in vivo SPME metabolomics.The AbsoluteIDQ kit enabled the targeted analysis of over 100 metabolites via solid-liquid extraction and SPME.Statistical analysis revealed significant differences between conventional liquid extractions from homogenized tissue and SPME results for both homogenized and intact tissue samples.In addition,principal component analysis revealed separated clustering among all the three sample groups,indicating changes in the metabolome due to tissue homogenization and the chosen sample preparation method.Furthermore,clear differences in free metabolites were observed when extractions were performed on the intact and homogenized tissue using identical SPME procedures.Specifically,a direct comparison showed that 47 statistically distinct metabolites were detected between the homogenized and intact lung tissue samples(P<0.05)using mixed-mode SPME fibers.These changes were probably due to the disruptive homogenization of the tissue.This study's findings highlight both the importance of sample preparation in tissue-based metabolomics studies and SPME's unique ability to perform minimally invasive extractions without tissue biopsy or homogenization while providing broad metabolite coverage.

Scalable solid-phase synthesis of defect-rich graphene for oxygen reduction electrocatalysis

Defect-engineered carbon materials have been emerged as promising electrocatalysts for oxygen reduction reaction(ORR)in metal-air batteries.Developing a facile strategy for the preparation of highly active nanocarbon electrocatalysts remains challenging.Herein,a low-cost and simple route is developed to synthesize defective graphene by pyrolyzing the mixture of glucose and carbon nitride.Molecular dynamics simulations reveal that the graphene formation is ascribed to two-dimensional layered feature of carbon nitride,and high compatibility of carbon nitride/glucose systems.Structural measurements suggest that the graphene possesses rich edge and topological defects.The graphene catalyst exhibits higher power density than commercial Pt/C catalyst in a primary Zn-air battery.Combining experimental results and theoretical thermodynamic analysis,it is identified that graphitic nitrogen-modified topological defects at carbon framework edges are responsible for the decent ORR performance.The strategy presented in this work can be can be scaled up readily to fabricate defective carbon materials.

Simultaneous nitrification and autotrophic denitrification in fluidized bed reactors using pyrite and elemental sulfur as electron donors

In this study, simultaneous nitrification and autotrophic denitrification (SNAD) with either elemental sulfur or pyrite were investigated in fluidized bed reactors in mesophilic conditions. The reactor performance was evaluated at different ammonium (12-40 mg/L of NH4+-N), nitrate (35-45 mg/L of NO3--N), and dissolved oxygen (DO) (0.1-1.5 mg/L) concentrations, with a hydraulic retention time of 12 h. The pyrite reactor supported the SNAD process with a maximum nitrogen removal efficiency of 139.5 mg/(L·d) when the DO concentration was in the range of 0.8-1.5 mg/L. This range, however, limited the denitrification efficiency of the reactor, which decreased from 90.0% ± 5.3% in phases II-V to 67.9% ± 7.2% in phases VI and VII. Sulfate precipitated as iron sulfate (FeSO4/Fe2(SO4)3) and sodium sulfate (Na2SO4) minerals during the experiment. The sulfur reactor did not respond well to nitrification with a low and unstable ammonium removal efficiency, while denitrification occurred with a nitrate removal efficiency of 97.8%. In the pyrite system, the nitrifying bacterium Nitrosomonas sp. was present, and its relative abundance increased from 0.1% to 1.1%, while the autotrophic denitrifying genera Terrimonas, Ferruginibacter, and Denitratimonas dominated the community. Thiobacillus, Sulfurovum, and Trichlorobacter were the most abundant genera in the sulfur reactor during the entire experiment.

A Model for Predicting the Erosion Rate Induced by the Use of a Selective Catalytic Reduction Denitrification Technology in Cement Kilns Flue Gas

Selective catalytic reduction(SCR)is a technology by which nitrogen oxides are converted with the aid of a catalyst into diatomic nitrogen and water.It is known that the catalyst can be easily eroded if a cement kiln with a high-dust content is considered.To understand this process,numerical simulations have been carried out considering a single catalyst channel in order to study the collision and erosion of fly ash and catalysts at meso scale.Based on a response surface methodology,the effects of five factors on the erosion rate have been studied,namely,the catalyst particle velocity,the particle size,the particle concentration,the incidence angle and the catalyst porosity.The results show that the influence of particle velocity,particle size and particle concentration is statistically significant and the particle size and incidence angle have a significant effect on the erosion rate.A quadratic polynomial prediction model for the erosion rate of honeycomb catalysts in cement kiln SCR reactors is finally proposed to support the future optimization of these systems.

Carbon Doping Triggered Efficient Electrochemical Hydrogen Evolution of Cross-Linked Porous Ru-MoO_(2) Via Solid-Phase Reaction Strategy

The defect-free structure of Mo-based materials is a“double-edged sword”,which endows the material with excellent stability,but limits its chemical versatility and application in electrochemical hydrogen evolution reaction(HER).Carbon doping engineering is an attractive strategy to effectively improve the performance of Mo-based catalyst and maintain their stability.Herein,we report a cross-linked porous carbon-doped MoO_(2)(C–MoO_(2))-based catalyst Ru/C–MoO_(2) for electrochemical HER,which is prepared by the convenient redox solid-phase reaction(SPR)of porous RuO_(2)/Mo_(2)C composite precursor.Theoretical studies reveal that due to the presence of carbon atoms,the electronic structure of C–MoO_(2) has been properly adjusted,and the loaded small Ru nanoparticles provide a fast water dissociation rate and moderate H adsorption strength.In electrochemical studies under a pH-universal environment,Ru/C–MoO_(2) electrocatalyst exhibits a low overpotential at a current density of 10 mA cm^(-2) and has a low Tafel slope.Meanwhile,Ru/C-MoO_(2) has excellent stability for more than 100 h at an initial current density of 100 mA cm^(-2).

Comparison of different approaches for direct coupling of solid-phase microextraction to mass spectrometry for drugs of abuse analysis in plasma

The direct coupling of solid-phase microextraction(SPME)to mass spectrometry(MS)(SPME-MS)has proven to be an effective method for the fast screening and quantitative analysis of compounds in complex matrices such as blood and plasma.In recent years,our lab has developed three novel SPME-MS techniques:SPME-microfluidic open interface-MS(SPME-MOI-MS),coated blade spray-MS(CBS-MS),and SPME-probe electrospray ionization-MS(SPME-PESI-MS).The fast and high-throughput nature of these SPME-MS technologies makes them attractive options for point-of-care analysis and anti-doping testing.However,all these three techniques utilize different SPME geometries and were tested with different MS instruments.Lack of comparative data makes it difficult to determine which of these methodologies is the best option for any given application.This work fills this gap by making a comprehensive comparison of these three technologies with different SPME devices including SPME fibers,CBS blades,and SPME-PESI probes and SPME-liquid chromatography-MS(SPME-LC-MS)for the analysis of drugs of abuse using the same MS instrument.Furthermore,for the first time,we developed different desorption chambers for MOI-MS for coupling with SPME fibers,CBS blades,and SPME-PESI probes,thus illustrating the universality of this approach.In total,eight analytical methods were developed,with the experimental data showing that all the SPME-based methods provided good analytical performance with R^(2)of linearities larger than 0.9925,accuracies between 81%and 118%,and good precision with an RSD%≤13%.

Influence of Pyrolytic Biochar on Settleability and Denitrification of Activated Sludge Process

Biochar is a massively produced by-product of biomass pyrolysis to obtain renewable energy and has not been fully used. Incomplete separation of sludge and effluent and insufficient denitrification of sewage are two of main factors that influence the efficiency of activated sludge process. In this work, we proposed a new utilization of biochar and investigated the effect of biochar addition on the performance of settleability and denitrification of activated sludge. Results show that the addition of biochar can improve the settleability of activated sludge by changing the physicochemical characteristics of sludge （e.g., flocculating ability, zeta-potential, hydrophobicity, and extracellular polymeric substances constituents）. Moreover, the dissolved organic carbon released from biochar obtained at lower pyrolysis temperature can improve the nitrate removal efficiency to a certain extent.

Low temperature solid-phase sintering of sintered metal fibrous media with high specific surface area

A procedure of low temperature solid-phase sintering（LTSS） was carried out to fabricate sintered metal fibrous media（SMFM） with high specific surface area.Stainless steel fibers which were produced by cutting process were first plated with a coarse copper coating layer by electroless plating process.A low-temperature sintering process was then completed at about 800 °C for 1 h under the protection of hydrogen atmosphere.The results show that a novel SMFM with complex surface morphology and high specific surface area（0.2 m2/g） can be obtained in this way.The effect of sintering temperature on the surface morphology and specific surface area of SMFM was studied by means of scanning electron microscopy and Brunauer-Emmett-Teller.The damage of micro-structure during the sintering process mainly contributed to the loss of specific surface area of SMFM and the optimal sintering temperature was 800 °C.

Solid-phase sintering process and forced convective heat transfer performance of porous-structured micro-channels

A solid-phase sintering process for the low-cost fabrication of composite micro-channels was developed. Three kinds of composite micro-channels with metallic porous structures were designed. The sintering process was studied and optimized to obtain porous-structured micro-channels with high porosity. The flow resistance and heat transfer performance in the composite micro-channels were investigated. The composite micro-channels show acceptable flow resistance, significant enhancement of heat transfer and dramatic improvement of flow boiling stability, which indicates a promising prospect for the application in forced convective heat transfer.

Chemiluminescence Determination of Benzoic Acid Using A Solid-Phase Verdigris Reactor

A new chemiluminescence flow system has been developed for sequential determina-tion of benzoic acid based on the reaction of the compound with copper carbonate entrapped in a solid-phase reactor. It was found that the unsaturated complex of Cu(II) and benzoic acid (1:1) has strong catalytic effect on the luminol-H2O2 chemiluminescence reaction. The calibration graph is linear over the range of 0.025 ~ 60 g/mL of benzoic acid, with a relative standard deviation of less than 3.0 %, and the detection limit is 0.01礸穖L-1. The proposed method was applied to the determination of benzoic acid content in different pharmaceutical formulations.

Determination of phthalate esters in fat-containing foods by packed nanofiber solid-phase extraction column and gas chromatography

A new method for simultaneous determination of four phthalate esters （ PAEs） in commercial fat-containing foods was developed by the combination of a packed nanofibers column based on solid-phase extraction with gas chromatography-flame ionization detector （ GC-FID ）. Conditions for obtaining optimum extraction efficiency such as extraction solvents, morphologies of adsorbent, ion strength and pH were investigated and optimized in detail. Under the optimized conditions, the limits of detection （LODs） found for dibutyl phthalate （DBP） , butyl benzyl phthalate （BBP）, diethyl hexyl phthalate （DEHP） and di-n-octyl phthalate （DNOP） were 50, 25, 50 and 25 ng/g, respectively. Good linearity of four PAEs was achieved in the range of 50 to 4 000 ng/g. The proposed method was applied for analyzing different kinds of fat-containing samples. PAEs in commercial fat-containing samples can be highly extracted by a packed solid-phase extraction column of 5 mg polystyrene （ PS） nanofibers. The satisfactory average recoveries were obtained in the range of 96. 7% to 102. 3% , and the relative standard deviations （RSDs） below 5% were achieved. The proposed method reduces the organic solvent consumption, the complex and tedious procedures for sample pretreatment, and achieves high sensitivity and reproducibility for the investigated PAEs.

HPLC Determination of Captopril in Human Plasma with Pre-column Derivation and Solid-phase Extraction and Studies on Its Pharmacokinetic and Relative Bioavailability

A new pre-column derivation HPLC method with solid-phase extraction to determine captopril in human plasma was established. Derivation products were extracted by a solid-phase extraction method after the reagent, p-a-dibromoacetophenone(p-BPB), was added in the plasma samples. The samples were analyzed in a VP-ODS column with UV-detector. The calibration curve of captopril was linear within the range of 5~1000 ngmL-1 with r=0.9987, the recovery of this method was 98.652.04%, within day and between day RSD were no more than 3.4% and 8.4% respectively. To study the pharmacokinetics and the relative bioavailability of captopril tablets, two formulations of captopril tablets were given to 18 healthy male volunteers according to a randomized 2-way cross-over design with a 1-week washout period. The respective AUC0~6 , Cmax and Tmax values of the two formulations were 424.5125.7 and 439.4113.3 mghL-1; 505.9244.6 and 504.8172.2 mgL-1; 0.6620.181 and 0.5280.176 h. Results from statistics analysis showed that there were no significant difference between the AUC0~6 , Cmax and Tmax values of the two formulations, The relative bioavailability of tablets I with respect to II was 96.114.6% from AUC0~6 measurement. Bioequivalance was observed between the two tablets.

Nitrification and Denitrification Activities and N_2O Emission of Orchard Soils Cultivated for Different Periods of Time

[Objective] The aim was to investigate the differences in nitrification and denitrification activities and the N20 emission of orchard soils cultivated for different periods of time. [Method] Incubation experiment was conducted to determine the ni- trification and denitrification activities and N20 emission of three types of orchard soil samples that had been cultivated for 5, 12 and 20 years, respectively, by using the virgin soil sample as control. [Result] After 26 d of incubation, the nitrification rates of nitrogen fertilizer in the virgin soil sample and the orchard soil samples cultivated for 5, 12 and 20 years were 6.85%, 10.26%, 13.29% and 12.90%, respectively, which were positively correlated with content of soil organic matter, ammonium nitro- gen and total nitrogen （P〈0.05）, and negatively correlated with soil carbon-nitrogen ratio and pH value （P〈0.05）. The denitrification activities of these soil samples in- creased with the increase of cultivation years. The amount of nitrogen loss by deni- trification accounted for 0.01%-3.11% of the amount of fertilizer nitrogen, and had a positive correlation with the content of soil organic matter （P〈0.05）. The N20 emis- sions of orchard soil samples were higher than that of the virgin soil samples （P〈 0.05）. [Conclusion] In South China, the nitrification activity of orchard soil is relatively low, but it has a tendency to increase as the cultivation years increases; the denitri- fication activity is relatively high, and increases significantly with the increase of culti- vation years.

Nitrogen Release Kinetics and Nitrification-Denitrification on Surface Sediments under Aerating Disturbance Condition

[Objective] This study aimed to investigate the nitrogen release kinetics and nitrification-denitrification on surface sediments under aerating disturbance condition, with the purpose to solve the sediment nitrogen release and secondary pollution problems. [Method] The effect of in situ sediments aeration on the release of nitrogen pollutants was investigated, and the nitrogen release kinetics parameters were analyzed. The process of nitrification and denitrification under sediments aeration condition was investigated in laboratory. [Result] The nitrogen released from sediments was enhanced by aeration disturbance. The concentration of NH4＋-N and TN reached the maximum value in 30 min, and release rates were proportional to the disturbance strength. In this study, with the distance of aerator to the sediments surface of 0, 1, 2 and 3 cm, the suspended sediments concentrations were 3.52, 3.41, 3.26 and 3.01 g/L, respectively. Maximum release concentration of NH4＋-N and TN were 14.3, 13.8, 13.2, 12.2 mg/L and 33.21, 30.98, 29.83, 27.30 mg/L, respec- tively. In addition, both NH4＋-N and TN release kinetics could be described by Double Constant Equation as InC=A＋Blnt. Nitrification reaction occurred and was promoted by continued aerating to sediments.The concentration of NH4＋-N dropped down from 12.4 mg/L to 0.2 mg/L in 8 d, with the concentration of NO3--N increased to the maximum value of 10.8 mg/L. In addition, concentration of NO3--N and TN decreased from 10.8 mg/L and 37.4 mg/L to 0.36 mg/L and 23.2 mg/L after the stop of aeration for 12 d, indicating the occurrence of denitdfication reaction. Therefore, sediment aeration could accelerate nitrogen release and nitrification reaction, and with intermittent aeration, nitrogen could be removed from sediments in-situ by nitrification and denitrification. [Conclusion] The results provided technical reference for the in situ sediment remediation for the black-odor rivers in cities.

Effect of carbon source on the denitrification in constructed wetlands

The ability of constructed wetlands with different plants in nitrate removal were investigated. The factors promoting the rates of denitrification including organic carbon, nitrate load, plants in wetlands, pH and water temperature in field were systematically investigated. The results showed that the additional carbon source （glucose） can remarkably improve the nitrate removal ability of the constructed wetland. It demonstrated that the nitrate removal rate can increase from 20% to more than 50% in summer and from 10% to 30% in winter, when the nitrate concentration was 30-40 rag/L, the retention time was 24 h and 25 mg/L dissolved organic carbon （DOC） was ploughed into the constructed wetland. However, the nitrite in the constructed wetland accumulated a little with the supply of the additional carbon source in summer and winter, and it increased from 0.15 to 2 mg/L in the effluent. It was also found that the abilities of plant in adjusting pH and temperature can result in an increase of denitrification in wetlands. The seasonal change may also impact the denitrification.

Simultaneous desulfurization and denitrification of sintering flue gas via composite absorbent

Experiments on simultaneous absorption of SO_2 and NO_X from sintering flue gas via a composite absorbent NaClO_2/NaClO were carried out. The effects of various operating parameters such as NaClO_2 concentration(ms), NaClO concentration(mp), molar ratio of NaClO_2/NaClO(M), solution temperature(TR), initial solution pH, gas flow(Vg) and inlet concentration of SO_2(CS) and NO(CN) on the removal efficiencies of SO_2 and NO were discussed. The optimal experimental conditions were determined to be initial solution pH = 6, TR=55 °C and M = 1.3 under which the average efficiencies of desulfurization and denitrification could reach99.7% and 90.8%, respectively. Moreover, according to the analysis of reaction products, it was found that adding NaClO to NaClO_2 aqueous solution is favorable for the generation of ClO_2 and Cl_2 which have significant effect on desulfurization and denitrification. Finally, engineering experiments were performed and obtained good results demonstrating that this method is practicable and promising.

The integration of methanogenesis with denitrification and anaerobic ammonium oxidation in an expanded granular sludge bed reactor

The integration of methanogenesis with denitrification and anaerobic ammonium oxidation(ANAMMOX) was studied in an expanded granular sludge bed(EGSB) reactor in this work. Experimental results from the continuous treatment of wastewater with nitrite and ammonium, which lasted for 107 days, demonstrated that wastewater with high nitrite and ammonium could be anaerobically treated in an expanded granular sludge bed reactor. More than 91% to 97% of COD were removed at up to about 3.9 g COD/(L·d) of COD volumetric loading rate. More than 97% to 100% of nitrite was denitrified at up to about 0.8 g NO -_2-N/(L·d), which is 16 times higher than that in a conventional activated sludge system with nitrification/denitrification(0.05 gN/(L·d)). No dissimilatory reduction of nitrite to ammonium occurred in the process. However, maximum of about 40% ammonium was found to be lost. Batch tests of 15 days with sludge from the reactor showed that 100% of nitrite was denitrified completely, and about 3% of ammonium was removed when only ammonium (34.3 mg/L) and nitrite(34.3 mg/L) were added into the sludge suspension medium. Furthermore, about 15% of ammonium amounts were lost with organic COD addition. It suggested that the methanogenesis in the system could enhance ANAMMOX because of intermediate hydrogen produced during methanogenesis.

Significance of dredging on sediment denitrification in Meiliang Bay,China:A year long simulation study

An experiment for studying the effects of sediment dredging on denitrification in sediments was carried out through a one-year incubation of undredged （control） and dredged cores in laboratory. Dredging the upper 30 cm of sediment can significantly affect physico-chemical characteristics of sediments. Less degradation of organic matter in the dredged sediments was found during the experiment. Denitrification rates in the sediments were estimated by the acetylene blockage technique, and ranged from 21.6 to 102.7 nmol N2/（g dry weight （dw）-hr） for the undredged sediment and from 6.9 to 26.9 nmol N2/（g dw-hr） for dredged sediments. The denitrification rates in the undredged sediments were markedly higher （p 〈 0.05） than those in the dredged sediments throughout the incubation, with the exception of February 2006. The importance of various environmental factors on denitrification was assessed, which indicated that denitrification was regulated by temperature. Nitrate was probably the key factor limiting denitrification in both undredged and dredged sediments. Organic carbon played some role in determining the denitrification rates in the dredged sediments, but not in the undredged sediments. Sediment dredging influenced the mineralization of organic matter and denitrification in the sediment; and therefore changed the pattern of inherent cycling of nitrogen.

Effects of chlorothalonil and carbendazim on nitrification and denitrification in soils

The effects of chlorothalonil and carbendazim on nitrification and denitrification in six soils in upland and rice paddy environments were investigated. Laboratory aerobic （60% water holding capacity） and anaerobic （flooded） conditions were studied at 25℃ and fungicide addition rates of 5.5 mg/kg A. I. （field rate, FR）, 20 times （20FR） and 40 times （40FR） field rate, respectively. The results indicated that chlorothalonil at the field rate had a slight inhibitory effect on one soil only, and that soil did not nitrify much in the first place. But chlorothalonil at higher rates inhibited nitrification significantly in all soils. For soils JXP and JXU with a pH of less than 5.0, chlorothalonil almost completely stopped their nitrification at 20FR and 40FR during the whole 14 d incubation period. For soils HNP and HNU with a pH of greater than 8.0, chlorothalonil also significantly inhibit nitrification at 20FR and 40FR （p 〈 0.05）. However, NH4＋ that was added to the soil was also almost completely nitrified by the end of the incubation period in these two soils. The effects of chlorothalonil at 20FR and 40FR on the nitrification of JSP and JSU soils, with a pH of 5.4 and 7.2, respectively, were intermediate between the other soil types. Chlorothalonil had no effect on denitrification at the field rate and had little effect at the higher rates of application in some soils. Carbendazim had essentially no effect on nitrification and denitrification in soils assessed.