Effect of Co on Solidification Characteristics and Microstructural Transformation of Non-equilibrium Solidified Cu-Ni Alloys

Non-equilibrium solidification structures of Cu55Ni45 and Cu55Ni43Co2 alloys were prepared by the molten glass purification cycle superheating method.The variation of the recalescence phenomenon with the degree of undercooling in the rapid solidification process was investigated using an infrared thermometer.The addition of the Co element affected the evolution of the recalescence phenomenon in Cu-Ni alloys.The images of the solid-liquid interface migration during the rapid solidification of supercooled melts were captured by using a high-speed camera.The solidification rate of Cu-Ni alloys,with the addition of Co elements,was explored.Finally,the grain refinement structure with low supercooling was characterised using electron backscatter diffraction(EBSD).The effect of Co on the microstructural evolution during nonequilibrium solidification of Cu-Ni alloys under conditions of small supercooling is investigated by comparing the microstructures of Cu55Ni45 and Cu55Ni43Co2 alloys.The experimental results show that the addition of a small amount of Co weakens the recalescence behaviour of the Cu55Ni45 alloy and significantly reduces the thermal strain in the rapid solidification phase.In the rapid solidification phase,the thermal strain is greatly reduced,and there is a significant increase in the characteristic undercooling degree.Furthermore,the addition of Co and the reduction of Cu not only result in a lower solidification rate of the alloy,but also contribute to the homogenisation of the grain size.

Preparation of Laser Cladding Coating Undercooling Cu-based Alloy and Co on Non-equilibrium Solidification Structure

The effect of the gradient content of Co element on the solidification process of Cu-based alloy under deep under cooling conditions was explored.The non-equilibrium solidification structure of the under cooled alloy samples were analyzed.It is found that the rapidly solidified alloy has undergone twice grain refinement during the undercooling process.Characterization and significance of the maximum undercooling refinement structure of Cu60Ni35Co5 at T=253 K were analyzed.High-density defects were observed,such as dislocations,stacking faults networks,and twinning structures.The standard FCC diffraction pattern represents that it is still a single-phase structure.Based on the metallographic diagram,EBSD and TEM data analysis,it is illustrated that the occurrence of grain refinement under high undercooling is due to stress induced recrystallization.In addition,the laser cladding technology is used to coat Co-based alloy(Stellite12) coating on 304 stainless steel substrate;the microstructure of the coating cross-section was analyzed.It was found that the microstructure of the cross-section is presented as columnar crystals,planar crystals,and disordered growth direction,so that the coating has better hardness and wear resistance.By electrochemical corrosion of the substrate and coating,it can be seen that the Co and Cr elements present in the coating are more likely to form a dense passivation film,which improved the corrosion resistance of the coating.

Effect of solidification cooling rate on microstructure and tribology characteristics of Zn-4Si alloy

The main objective of this work was to modify the microstructure and enhance the tribological properties of a new Zn-4Si al-loy through a high solidification cooling rate(SCR).According to the results,by increasing the SCR from 2.0 to 59.5℃/s the average size of primary Si particles and that of the grains reduced from 76.1 and 3780μm to less than about 14.6 and 460μm,respectively.Augment-ing the SCR also enhanced the microstructural homogeneity,decreased the porosity content(by 50%),and increased the matrix hardness(by 36%).These microstructural changes enhanced the tribological behavior.For instance,under the applied pressure of 0.5 MPa,an in-crease in the SCR from 2.0 to 59.5℃/s decreased the wear rate and the average friction coefficient of the alloy by 57%and 23%,respect-ively.The wear mechanism was also changed from the severe delamination,adhesion,and abrasion in the slowly-cooled alloy to the mild tribolayer delamination/abrasion in the high-cooling-rate-solidified sample.

Volume-averaged modeling of multiphase solidification with equiaxed crystal sedimentation in a steel ingot

Macrosegregation is a critical factor that limits the mechanical properties of materials.The impact of equiaxed crystal sedimentation on macrosegregation has been extensively studied,as it plays a significant role in determining the distribution of alloying elements and impurities within a material.To improve macrosegregation in steel connecting shafts,a multiphase solidification model that couples melt flow,heat transfer,microstructure evolution,and solute transport was established based on the volume-averaged Eulerian-Eulerian approach.In this model,the effects of liquid phase,equiaxed crystals,columnar dendrites,and columnar-to-equiaxed transition(CET)during solidification and evolution of microstructure can be considered simultaneously.The sedimentation of equiaxed crystals contributes to negative macrosegregation,where regions between columnar dendrites and equiaxed crystals undergo significant A-type positive macrosegregation due to the CET.Additionally,noticeable positive macrosegregation occurs in the area of final solidification in the ingot.The improvement in macrosegregation is beneficial for enhancing the mechanical properties of connecting shafts.To mitigate the thermal convection of molten steel resulting from excessive superheating,reducing the superheating during casting without employing external fields or altering the design of the ingot mold is indeed an effective approach to control macrosegregation.

Irregular initial solidification by mold thermal monitoring in the continuous casting of steels:A review

Occasional irregular initial solidification phenomena,including stickers,deep oscillation marks,depressions,and surface cracks of strand shells in continuous casting molds,are important limitations for developing the high-efficiency continuous casting of steels.The application of mold thermal monitoring(MTM) systems,which use thermocouples to detect and respond to temperature variations in molds,has become an effective method to address irregular initial solidification phenomena.Such systems are widely applied in numerous steel companies for sticker breakout prediction.However,monitoring the surface defects of strands remains immature.Hence,indepth research is necessary to utilize the potential advantages and comprehensive monitoring of MTM systems.This paper summarizes what is included in the irregular initial solidification phenomena and systematically reviews the current state of research on these phenomena by the MTM systems.Furthermore,the influences of mold slag behavior on monitoring these phenomena are analyzed.Finally,the remaining problems of the formation mechanisms and investigations of irregular initial solidification phenomena are discussed,and future research directions are proposed.

Exploration of the coupled lattice Boltzmann model based on a multiphase field model:A study of the solid-liquid-gas interaction mechanism in the solidification process

A multiphase field model coupled with a lattice Boltzmann(PF-LBM)model is proposed to simulate the distribution mechanism of bubbles and solutes at the solid-liquid interface,the interaction between dendrites and bubbles,and the effects of different temperatures,anisotropic strengths and tilting angles on the solidified organization of the SCN-0.24wt.%butanedinitrile alloy during the solidification process.The model adopts a multiphase field model to simulate the growth of dendrites,calculates the growth motions of dendrites based on the interfacial solute equilibrium;and adopts a lattice Boltzmann model(LBM)based on the Shan-Chen multiphase flow to simulate the growth and motions of bubbles in the liquid phase,which includes the interaction between solid-liquid-gas phases.The simulation results show that during the directional growth of columnar dendrites,bubbles first precipitate out slowly at the very bottom of the dendrites,and then rise up due to the different solid-liquid densities and pressure differences.The bubbles will interact with the dendrite in the process of flow migration,such as extrusion,overflow,fusion and disappearance.In the case of wide gaps in the dendrite channels,bubbles will fuse to form larger irregular bubbles,and in the case of dense channels,bubbles will deform due to the extrusion of dendrites.In the simulated region,as the dendrites converge and diverge,the bubbles precipitate out of the dendrites by compression and diffusion,which also causes physical phenomena such as fusion and spillage of the bubbles.These results reveal the physical mechanisms of bubble nucleation,growth and kinematic evolution during solidification and interaction with dendrite growth.

Recent research progress on the phase-field model of microstructural evolution during metal solidification

Solidification structure is a key aspect for understanding the mechanical performance of metal alloys,wherein composition and casting parameters considerably influence solidification and determine the unique microstructure of the alloys.By following the principle of free energy minimization,the phase-field method eliminates the need for tracking the solid/liquid phase interface and has greatly accelerated the research and development efforts geared toward optimizing metal solidification microstructures.The recent progress in the application of phasefield simulation to investigate the effect of alloy composition and casting process parameters on the solidification structure of metals is summarized in this review.The effects of several typical elements and process parameters,including carbon,boron,silicon,cooling rate,pulling speed,scanning speed,anisotropy,and gravity,on the solidification structure are discussed.The present work also addresses the future prospects of phase-field simulation and aims to facilitate the widespread applications of phase-field approaches in the simulation of microstructures during solidification.

High-Performance Quasi-Solid-State Pouch Cells Enabled by in situ Solidification of a Novel Polymer Electrolyte

Conventional lithium-ion batteries(LIBs)with liquid electrolytes are challenged by their big safety concerns,particularly used in electric vehicles.All-solid-state batteries using solid-state electrolytes have been proposed to significantly improve safety yet are impeded by poor interfacial solid–solid contact and fast interface degradation.As a compromising strategy,in situ solidification has been proposed in recent years to fabricate quasi-solid-state batteries,which have great advantages in constructing intimate interfaces and cost-effective mass manufacturing.In this work,quasi-solid-state pouch cells with high loading electrodes(≥3 m Ah cm^(-2))were fabricated via in situ solidification of poly(ethylene glycol)diacrylate-based polymer electrolytes(PEGDA-PEs).Both single-layer and multilayer quasi-solid-state pouch cells(2.0 Ah)have demonstrated stable electrochemical performance over500 cycles.The superb electrochemical stability is closely related to the formation of robust and compatible interphase,which successfully inhibits interfacial side reactions and prevents interfacial structural degradation.This work demonstrates that in situ solidification is a facile and cost-effective approach to fabricate quasi-solid-state pouch cells with both excellent electrochemical performance and safety.

Solidification microstructure of Ti-43Al alloy by twin-roll strip casting

As a near-net-shape technology,the twin-roll strip casting(TRC)process can be considered to apply to the fabrication of TiAl alloy sheets.However,the control of the grain distribution is very important in strip casting because the mechanical properties of strips are directly determined by the solidification microstructure.A three-dimensional(3D)cellular automation finite-element(CAFE)model based on ProCAST software was established to simulate the solidification microstructure of Ti-43Al alloy.Then,the influence of casting temperature and the maximum nucleation density(nmax)on the solidification microstructure was investigated in detail.The simulation results provide a good explanation and prediction for the solidification microstructure in the molten pool before leaving the kissing point.Experimental and simulated microstructure show the common texture<001>orientation in the columnar grains zone.Finally,the microstructure evolution of the Ti-43Al alloy was analyzed and the solidification phase transformation path during the TSC process was determined,i.e.,L→L+β→β→β+α→α+γ+β/B2 phase under a faster cooling rate and L→L+β→β→β+α→γ+lamellar(α_(2)+γ)+β/B2 phase under a slower cooling rate.

Effect of Cooling Rates on Solidification Microstructures and Tensile Property of a Novel Wrought Superalloy

The effects of cooling rates on solidification behaviors,segregation characteristics and tensile property of GH4151 alloy were investigated using microstructure characterization and tensile test.Firstly,a relationship between the secondary dendrite arm spacing and cooling rate was determined and it was confirmed to be valid.Secondly,it can be found from microstructure observations that the morphology of(Nb,Ti)C carbides transits from blocky and script type to fine script type and spotty type,and the refinedγ'phase was observed due to decrease of segregation with increasing cooling rates.Thirdly,the solidification microstructures of the industrial-scale samples were analyzed.The morphology ofηphase changes from indistinguishable shape,fine needle-like shape to large block-like shape with increasing ingot diameter.As a result,the mechanical properties of alloy decrease due to increase of brittle precipitations.The experimental results show that the precipitation behavior of GH4151 is affected by segregation degree of elements,and the segregation degree is determined by solute distribution process and solid back-diffusion process.

Dislocation mechanism of Ni_(47)Co_(53) alloy during rapid solidification

Dislocations and other atomic-level defects play a crucial role in determining the macroscopic properties of crystalline materials,but it is extremely difficult to observe the evolution of dislocations due to the limitations of the most advanced experimental techniques.Therefore,in this work,the rapid solidification processes of Ni_(47)Co_(53) alloy at five cooling rates are studied by molecular dynamics simulation,and the evolutions of their microstructures and dislocations are investigated as well.The results show that face-centered cubic(FCC) structures are formed at the low cooling rate,and the crystalline and amorphous mixture appear at the critical cooling rate,and the amorphous are generated at the high cooling rate.The crystallization temperature and crystallinity decrease with cooling rate increasing.Dislocations are few at the cooling rates of 1×10^(11) K/s,5×10^(12) K/s,and 1×10^(13) K/s,and they are most abundant at the cooling rates of 5×10^(11) K/s and1 × 10^(12) K/s,in which their dislocation line lengths are both almost identical.There appear a large number of dislocation reactions at both cooling rates,in which the interconversion between perfect and partial dislocations is primary.The dislocation reactions are more intense at the cooling rate of 5×10^(11) K/s,and the slip of some dislocations leads to the interconversion between FCC structure and hexagonal close packed(HCP) structure,which causes the twin boundaries(TBs) to disappear.The FCC and HCP are in the same atomic layer,and dislocations are formed at the junction due to the existence of TBs at the cooling rate of 1 ×10^(12) K/s.The present research is important in understanding the dislocation mechanism and its influence on crystal structure at atomic scales.

Effect of Ta on solidification characteristics and mechanical properties of DZ411 Ni-based superalloy

The effects of Ta content(2.72wt.%,3.10wt.%and 4.00wt.%)on the solidification characteristics and mechanical properties of directionally solidified DZ411 Ni-based superalloys were investigated.It is found that the content of Mo decreases with the increase of Ta in liquid phase after directional solidification,indicating the addition of Ta can reduce the element segregation in alloys.The primary and secondary dendrite arm spacings(PDAS and SDAS)of the DZ411 alloy increase with the addition of Ta,which are consistent with the models by Hunt and Wagner.The increase of PDAS and SDAS can provide enough space for the growth of tertiary dendrite arms,which hinders the growth of unfavorably oriented primary dendrites.As a result,the addition of Ta facilitates the growth of favorably oriented dendrites.More MC carbides andγ-γ'eutectics are formed in the interdendritic regions,which is attributed to the segregation of Ta in the liquid phase.Furthermore,the degree of supersaturation of W,Mo inγmatrix increases with the increase of Ta,thus,the addition of Ta promotes the formation of TCP phase.The addition of Ta also increases the microhardness in both the primary dendrite and interdendritic regions of the alloy,and the microhardness of the primary dendrite is closer to that in interdendritic regions with the increase of Ta.

Simulation and Optimization of the Fluid Solidification Process in Brazed Plate Heat Exchangers

When a brazed plate heat exchanger is used as an evaporator,the working mass in the channel may undergo soli-dification,thereby hindering the refrigeration cycle.In this study the liquid solidification process and its optimi-zation in a brazed plate heat exchanger are investigated numerically for different inlet velocities;moreover,different levels of corrugation are considered.The results indicate that solidificationfirst occurs around the con-tacts,followed by the area behind the contacts.It is also shown that deadflow zones exist in the sharp areas and such areas are prone to liquid solidification.After optimization,the solidification area attains its smallest value when a corrugation spacingλ=4.2 mm is considered.

Three dimensional phase-field simulation for non-isothermal binary alloy solidification: Comparison with LKT theory

Using the advanced algorithm combining parallel computing,adaptive mesh re-griding and multigrid methods,quantitative 3D phase-field simulations of non-isothermal solidification of binary alloy were carried out.The 3D phase-field simulation results were compared with the analytical LKT(Lipton,Kurz and Trivedi)theory.For comparison,the simulation and analytical results for 2D cases were also given.The 3D phase-field simulation results support the transport portion of the LKT theory.However,the tip radius and tip velocity predicted by the simulations are not in good agreement with the LKT theory over the whole range of undercooling.The stability parameter calculated from phase-field simulations varies significantly with the Peclet number,indicating that the stability criterion,which assumes that the stability parameter is constant,is invalid.

Effect of mixing temperature on microstructure of an Al-Si alloy prepared by controlled diffusion solidification

The effects of mixing temperature,i.e.,the temperatures of two precursor melts(pure Al and Al-12Si),on the temperature and solute fields of resultant mixture,the nucleation and growth,and the size and morphology of primary grains during controlled diffusion solidification(CDS) of Al-8Si alloy were investigated by using simulation and calculation.The results indicate that a lower mixing temperature is helpful for achieving more supercooled microscale Al-rich pockets in the mixture,and increasing the width and supercooling degree of supercooling zone in the Al-rich pockets,and thus,the nucleation rate.The nuclei grow up in nondendritic mode,resulting in spheroidal,at least,nondendritic grains.In a successful CDS,the superheat degrees of the two precursor melts should be limited within several degrees,and it is not necessary to extra stipulate the superheat degree of target alloy melt(Al-8Si) when the requirement about Gibbs energies of the three melts is matched.Subsequent observation on casting microstructures shows that the employed simulation and calculation processes are reasonable and the achieved results are reliable.

Effects of mechanical vibration on filling and solidification behavior, microstructure and performance of Al/Mg bimetal by lost foam compound casting

Al/Mg bimetal was prepared by lost foam solid-liquid compound casting,and the effects of mechanical vibration on the filling and solidification behavior,microstructure and performance of the bimetal were investigated.Results show that the mechanical vibration has a remarkable influence on the filling and solidification processes.It is found that after mechanical vibration,the filling rate increases and the filling rate at different times is more uniform than that without vibration.In addition,the mechanical vibration also increases the wettability between liquid AZ91D and A356 inlays.The mechanical vibration reduces the horizontal and vertical temperature gradient of the casting and makes the temperature distribution of the whole casting more uniform.Compared to the Al/Mg bimetal without vibration,the shear strength is improved by 39.76%after the mechanical vibration is applied,due to the decrease of the inclusions and Al_(12)Mg_(17) dendrites,and the refinement and uniform distribution of the Mg_(2)Si particles in the interface of the Al/Mg bimetal.

全渠道零售商引入SFS模式时的定价决策分析

全渠道零售背景下许多大型零售商在已有BOPS(线上下单门店自提)模式的基础上,开始探索引入SFS(线上下单门店发货)模式。本文通过对比全渠道零售商只实施BOPS模式与同时实施BOPS和SFS模式的情形,探讨全渠道零售商引入SFS模式的条件,以及SFS模式的实施对零售商定价决策、需求和利润的影响。研究结果表明,顾客到店产生的交叉销售收益较高或者零售商提供的配送服务水平较低时,SFS模式的引入并不能使零售商获利。另外,若零售商引入SFS模式的目标是扩大市场份额,吸引更多的潜在消费者,则可选择不改变产品定价的决策;若零售商引入SFS模式的目标是尽可能地提升利润,则可选择改变产品定价,以最优定价作决策。

Development of Low-carbon and Sustainable Magnesium-bearing Cementitious Materials-based Solidification Approaches for Management of Problematic Soils

The production of traditional cementitious binders such as calcium-based Portland cement poses a serious challenge to the environment and society.Therefore,low-carbon,green and sustainable magnesium-based cementitious materials are developed to replace fully or partly Portland cement and reduce the consumption of natural resources and CO_(2)emissions.Three interesting techniques,including reactive MgO-activated industrial solid wastes,MgO-based cement and carbonation of magnesium-bearing materials,are elucidated to point to the necessity for developing novel magnesium-based cementitious materials.In the coming future,the carbonation of magnesium-rich industrial solid wastes or its combination with reactive MgO for application in various construction sectors such as soft ground improvement and concrete fabrication would be a promising approach to generate high-value products based on industrial solid wastes.

Mayr电弧模型下GIS中快速暂态过电压的仿真分析

SF6气体绝缘封闭组合开关(GIS)中隔离开关进行分合母线时,产生快速暂态过电压(VFTO),幅值高且上升速率极快,威胁GIS及相邻设备的绝缘。选取某800 kV GIS隔离开关分合母线的试验电路为研究对象,采用电磁暂态程序(EMTP/ATP)进行建模仿真,隔离开关燃弧时采用Mayr电弧模型,分析其对VFTO的影响,得出考虑Mayr电弧模型时操作隔离开关、断路器侧隔离开关及变压器侧隔离开关的电压波形,并与考虑时变电阻模型的VFTO进行对比。对VFTO波形进行离散傅里叶分析,得到过电压频率、幅值的变化特征,研究结果为GIS绝缘设计提供参考。

定向凝固Cu-50%Sn包晶合金显微组织演变

随着科学技术的进步,越来越多的包晶合金因其优良性能广泛应用于工业生产领域,比如Fe-Cr-Ni、Ti-Al、Nd-Fe-B合金以及应用于电子封装领域的Cu-Sn合金等。随着电子信息产业向微型化和多功能化方向发展,对集成电路的机械、电子和热性能提出了更高的要求。本文以Cu-50%Sn(原子分数)包晶合金(L+Cu^(3)Sn→Cu6Sn5)作为研究对象,通过布里奇曼定向凝固法,在显微镜下对组织进行观察和测量,研究淬火固液界面的凝固组织随凝固条件改变而产生的变化。生长距离、温度梯度一定时,随着生长速度的增大,初生相Cu^(3)Sn经历了胞状→胞/枝状→枝晶状组织转变,Cu^(3)Sn相的尺寸与间距均随生长速度的增大而减小;生长速度、生长距离一定时,随着温度梯度的增大,初生相Cu^(3)Sn相由块状与枝晶状转变为胞状组织;生长速度、温度梯度一定时,随着生长距离的增大,初生相Cu^(3)Sn由块状与胞/枝状转变为胞状组织,且Cu^(3)Sn相尺寸发生小幅细化。基于上述实验结果,绘制了关于生长速度、温度梯度及生长距离条件下的显微组织选择图,进一步阐明了凝固条件的改变对Cu-50%Sn(原子分数)包晶合金显微组织的影响。