In recent years, the data collecting and processing of magnetotelluric sounding （MT） have progressed greatly. How to improve the quality of field surveyed data and obtain the high quality parameters such as apparent...In recent years, the data collecting and processing of magnetotelluric sounding （MT） have progressed greatly. How to improve the quality of field surveyed data and obtain the high quality parameters such as apparent resistivity and phase is the most important link during the overall flow. It is closely related to the signal-to-noise ratio of magnetic sensors, the resolution of data collecting units and relevant processing methods as well. Produced by Germany Metronix Measurement Instruments and Electronics Ltd., the new type multi-channel geophysical measurement system GMS-06 was already adopted and used by domeslic units such as Institute of Geology and Geophysics of Chinese Academy of Sciences and Tongji University. Based on the brief introduction of GMS-06, this paper will give the comparisons and analyses of the synchronous surveyed MT data by GMS-06, MMS-03 MT system which was also produced by Metronix and V5-2000 MT system produced by Canada Phoenix Geophysics Ltd.. Then the preliminary processing and interpretation results of the long period MT data observed by GMS-06 in the area of Shanghai and Zhejiang are also discussed in the paper.展开更多
During the last few decades, photothermal radiometry（PTR） has been greatly developed and widely applied in the field of nondestructive testing. However, the traditional PTR system employs an expensive lock-in amplif...During the last few decades, photothermal radiometry（PTR） has been greatly developed and widely applied in the field of nondestructive testing. However, the traditional PTR system employs an expensive lock-in amplifier to detect the weak photothermal signal, which leads to high cost and long test time. In this paper, a fast transmission PTR system based on sampling by using an internal computer sound card was developed to lower the system cost and shorter the test time. A piece of amorphous silicon（a：Si） thin film solar cells with artificial defects was prepared and tested by the system. The results show that the sharpened defects can be identified easily and quickly according to the significant peaks of the original infrared signal sampled by the internal computer sound card. Furthermore, more detailed defects can be investigated by processing the infrared signal. These validate the effectiveness of the proposed transmission PTR system as a low cost and efficient non-destructive test technique.展开更多
This paper deals with the issue of using the MATLAB tool in teaching the course of communication principles via constructing an Amplitude Shift Keying (ASK) communication system. Different from conventional MATLAB bas...This paper deals with the issue of using the MATLAB tool in teaching the course of communication principles via constructing an Amplitude Shift Keying (ASK) communication system. Different from conventional MATLAB based simulations, the constructed system transmits modulated signals through a wire audio channel by exploiting sound card. Synchronization is required before the received signal being demodulated. Many practical problems should be considered as in real system. The designed system can be extended easily, and not only stimulates students’ interest in communication course, but also helps them understanding the principles from system viewpoints.展开更多
Based on the structure of chute - feed and autoleveHer, an analysis of their working principle and the verification of their practical production results have been carried out. Finally, the future investigation direet...Based on the structure of chute - feed and autoleveHer, an analysis of their working principle and the verification of their practical production results have been carried out. Finally, the future investigation direetiom of chute - feed and card autuleveller are put forward.展开更多
On the basis of the finite element analysis, the elastic wave propagation in cellular structures is investigated using the symplectic algorithm. The variation principle is first applied to obtain the dual variables an...On the basis of the finite element analysis, the elastic wave propagation in cellular structures is investigated using the symplectic algorithm. The variation principle is first applied to obtain the dual variables and the wave propagation problem is then transformed into two-dimensional （2D） symplectic eigenvalue problems, where the extended Wittrick-Williams algorithm is used to ensure that no phase propagation eigenvalues are missed during computation. Three typical cellular structures, square, triangle and hexagon, are introduced to illustrate the unique feature of the symplectic algorithm in higher-frequency calculation, which is due to the conserved properties of the structure-preserving symplectic algorithm. On the basis of the dispersion relations and phase constant surface analysis, the band structure is shown to be insensitive to the material type at lower frequencies, however, much more related at higher frequencies. This paper also demonstrates how the boundary conditions adopted in the finite element modeling process and the structures＇ configurations affect the band structures. The hexagonal cells are demonstrated to be more efficient for sound insulation at higher frequencies, while the triangular cells are preferred at lower frequencies. No complete band gaps are observed for the square cells with fixed-end boundary conditions. The analysis of phase constant surfaces guides the design of 2D cellular structures where waves at certain frequencies do not propagate in specified directions. The findings from the present study will provide invaluable guidelines for the future application of cellular structures in sound insulation.展开更多
In this paper, the effects of turbulence on sound generation and velocity fluctuations due to pressure waves in a large subsonic wind tunnel are studied. A trip strip located at different positions in the contraction ...In this paper, the effects of turbulence on sound generation and velocity fluctuations due to pressure waves in a large subsonic wind tunnel are studied. A trip strip located at different positions in the contraction part or at one position in the diffuser of a large wind tunnel is used to investigate the aforementioned phenomenon, and the results indicate that the trip strip has significant effects on sound reduction. The lowest turbulence intensity and sound are obtained from a trip strip with a diameter of 0.91 mm located either at X/L = 0.79 or at X/L = 0.115 in the wide portion of the contraction. Furthermore, the effect of monopole, dipole and quadrupole sources of aerodynamic noise at different velocities is investigated, and it is demonstrated that the contribution of the monopole is dominant, while the shares due to the dipole and quadrupole remain less important. In addition, it is found that the sound waves have a modest impact on the measured longitudinal turbulence and are generated essentially by eddies.展开更多
As is known to all, many auscultations of human body, such as heart, lung and carotid artery sound, play a major role in clinic. And their signal frequency is in the range that computer sound card can handle, so we ca...As is known to all, many auscultations of human body, such as heart, lung and carotid artery sound, play a major role in clinic. And their signal frequency is in the range that computer sound card can handle, so we can use analog-to-digital (A/D) conversion of sound card as A/D conversion (ADC) of auscultation signals, and double-channel auscultation signals (DCASs) can be input into personal computer(PC) by sound card that every computer has, and it makes the hardware design more simple. Because auscultation signals are input from sound card, any common music processing software (CMPS) can be used to process received auscultative signals, and it is not necessary to write special processing software for them. Therefore, only a double-channel and front-end analog signal processing circuit of auscultation is needed to be designed. By this method of constituting the signal collecting system for double-channel auscultation, it is simple and low cost, and needs no special software, so it has very important values and a broad market prospect.展开更多
We describe a radio-echo sounding (RES) survey for the determination of ice thickness, subglacial topography and ice volume of Glacier No. 1 , in Tien Shan, China, using ground-penetrating radar (GPR). Radar data were...We describe a radio-echo sounding (RES) survey for the determination of ice thickness, subglacial topography and ice volume of Glacier No. 1 , in Tien Shan, China, using ground-penetrating radar (GPR). Radar data were collected with 100-MHz antennas that were spaced at 4 m with a step size of 8 m. The images produced from radar survey clearly show the continuity of bedrock echoes and the undulation features of the bedrock surface. Radar results show that the maximum ice thickness of Glacier No. 1 is 133 m, the thickness of the east branch of Glacier No. 1 averages at 58. 77 m while that of the west branch of Glacier No. 1 averages at 44. 84 m. Calculation on ice volume indicates that the ice volume of the east branch of Glacier No. 1 is 51. 87 × 106 m3 and that of the west branch of Glacier No. 1 is 20. 21 × 106 m3. The amplitude of the undulation of the bedrock surface topography revealed by radar profiles is larger than that of the glacier surface topography, indicating that the surface relief does not directly depend on that of the bedrock undulation in Glacier No. 1 , in Tien Shan.展开更多
基金National Natural Science Foundation of China (40104005) and National High Technical Research and Development Project (2004AA615010).
文摘In recent years, the data collecting and processing of magnetotelluric sounding （MT） have progressed greatly. How to improve the quality of field surveyed data and obtain the high quality parameters such as apparent resistivity and phase is the most important link during the overall flow. It is closely related to the signal-to-noise ratio of magnetic sensors, the resolution of data collecting units and relevant processing methods as well. Produced by Germany Metronix Measurement Instruments and Electronics Ltd., the new type multi-channel geophysical measurement system GMS-06 was already adopted and used by domeslic units such as Institute of Geology and Geophysics of Chinese Academy of Sciences and Tongji University. Based on the brief introduction of GMS-06, this paper will give the comparisons and analyses of the synchronous surveyed MT data by GMS-06, MMS-03 MT system which was also produced by Metronix and V5-2000 MT system produced by Canada Phoenix Geophysics Ltd.. Then the preliminary processing and interpretation results of the long period MT data observed by GMS-06 in the area of Shanghai and Zhejiang are also discussed in the paper.
基金supported by the National Natural Science Foundation of China under Grant No.61379013the Excellent Doctoral Academic Support Program under Grant No.YBXSZC2013021
文摘During the last few decades, photothermal radiometry（PTR） has been greatly developed and widely applied in the field of nondestructive testing. However, the traditional PTR system employs an expensive lock-in amplifier to detect the weak photothermal signal, which leads to high cost and long test time. In this paper, a fast transmission PTR system based on sampling by using an internal computer sound card was developed to lower the system cost and shorter the test time. A piece of amorphous silicon（a：Si） thin film solar cells with artificial defects was prepared and tested by the system. The results show that the sharpened defects can be identified easily and quickly according to the significant peaks of the original infrared signal sampled by the internal computer sound card. Furthermore, more detailed defects can be investigated by processing the infrared signal. These validate the effectiveness of the proposed transmission PTR system as a low cost and efficient non-destructive test technique.
文摘This paper deals with the issue of using the MATLAB tool in teaching the course of communication principles via constructing an Amplitude Shift Keying (ASK) communication system. Different from conventional MATLAB based simulations, the constructed system transmits modulated signals through a wire audio channel by exploiting sound card. Synchronization is required before the received signal being demodulated. Many practical problems should be considered as in real system. The designed system can be extended easily, and not only stimulates students’ interest in communication course, but also helps them understanding the principles from system viewpoints.
文摘Based on the structure of chute - feed and autoleveHer, an analysis of their working principle and the verification of their practical production results have been carried out. Finally, the future investigation direetiom of chute - feed and card autuleveller are put forward.
基金supported by the National Natural Science Foundation of China (10972182, 10772147, 10632030)the National Basic Research Program of China (2006CB 601202)+3 种基金the Doctorate Foundation of Northwestern Polytechnical University (CX200908)the Graduate Starting Seed Fund of Northwestern Polytechnical University (Z200930)the NPU Foundation for Fundamental Researchthe Open Foundation of State Key Laboratory of Structural Analysis of Industrial Equipment (GZ0802)
文摘On the basis of the finite element analysis, the elastic wave propagation in cellular structures is investigated using the symplectic algorithm. The variation principle is first applied to obtain the dual variables and the wave propagation problem is then transformed into two-dimensional （2D） symplectic eigenvalue problems, where the extended Wittrick-Williams algorithm is used to ensure that no phase propagation eigenvalues are missed during computation. Three typical cellular structures, square, triangle and hexagon, are introduced to illustrate the unique feature of the symplectic algorithm in higher-frequency calculation, which is due to the conserved properties of the structure-preserving symplectic algorithm. On the basis of the dispersion relations and phase constant surface analysis, the band structure is shown to be insensitive to the material type at lower frequencies, however, much more related at higher frequencies. This paper also demonstrates how the boundary conditions adopted in the finite element modeling process and the structures＇ configurations affect the band structures. The hexagonal cells are demonstrated to be more efficient for sound insulation at higher frequencies, while the triangular cells are preferred at lower frequencies. No complete band gaps are observed for the square cells with fixed-end boundary conditions. The analysis of phase constant surfaces guides the design of 2D cellular structures where waves at certain frequencies do not propagate in specified directions. The findings from the present study will provide invaluable guidelines for the future application of cellular structures in sound insulation.
基金supported by the Iranian Aircraft Manufacturing (HESA) company,Bureau of Aircraft Design
文摘In this paper, the effects of turbulence on sound generation and velocity fluctuations due to pressure waves in a large subsonic wind tunnel are studied. A trip strip located at different positions in the contraction part or at one position in the diffuser of a large wind tunnel is used to investigate the aforementioned phenomenon, and the results indicate that the trip strip has significant effects on sound reduction. The lowest turbulence intensity and sound are obtained from a trip strip with a diameter of 0.91 mm located either at X/L = 0.79 or at X/L = 0.115 in the wide portion of the contraction. Furthermore, the effect of monopole, dipole and quadrupole sources of aerodynamic noise at different velocities is investigated, and it is demonstrated that the contribution of the monopole is dominant, while the shares due to the dipole and quadrupole remain less important. In addition, it is found that the sound waves have a modest impact on the measured longitudinal turbulence and are generated essentially by eddies.
文摘As is known to all, many auscultations of human body, such as heart, lung and carotid artery sound, play a major role in clinic. And their signal frequency is in the range that computer sound card can handle, so we can use analog-to-digital (A/D) conversion of sound card as A/D conversion (ADC) of auscultation signals, and double-channel auscultation signals (DCASs) can be input into personal computer(PC) by sound card that every computer has, and it makes the hardware design more simple. Because auscultation signals are input from sound card, any common music processing software (CMPS) can be used to process received auscultative signals, and it is not necessary to write special processing software for them. Therefore, only a double-channel and front-end analog signal processing circuit of auscultation is needed to be designed. By this method of constituting the signal collecting system for double-channel auscultation, it is simple and low cost, and needs no special software, so it has very important values and a broad market prospect.
基金the National Natural Science Foundation of China(No.40071022)the Ministry of Science and tchnology,the People's Republic of China(No.2001DIA50040)+1 种基金Tien Shan Glacier Station Research FoundationLaboratory foundation of Iee Core and Cold Region Envionment,Cold and Anid Regions Enironmental and Engineeing Insitute,Chinese Academry of Sciences(No.BX2001-04).
文摘We describe a radio-echo sounding (RES) survey for the determination of ice thickness, subglacial topography and ice volume of Glacier No. 1 , in Tien Shan, China, using ground-penetrating radar (GPR). Radar data were collected with 100-MHz antennas that were spaced at 4 m with a step size of 8 m. The images produced from radar survey clearly show the continuity of bedrock echoes and the undulation features of the bedrock surface. Radar results show that the maximum ice thickness of Glacier No. 1 is 133 m, the thickness of the east branch of Glacier No. 1 averages at 58. 77 m while that of the west branch of Glacier No. 1 averages at 44. 84 m. Calculation on ice volume indicates that the ice volume of the east branch of Glacier No. 1 is 51. 87 × 106 m3 and that of the west branch of Glacier No. 1 is 20. 21 × 106 m3. The amplitude of the undulation of the bedrock surface topography revealed by radar profiles is larger than that of the glacier surface topography, indicating that the surface relief does not directly depend on that of the bedrock undulation in Glacier No. 1 , in Tien Shan.
