Solid-state impedance spectroscopy studies of dielectric properties and relaxation processes in Na_(2)O–V_(2)O_(5)–Nb_(2)O_(5)–P_(2)O_(5) glass

Solid-state impedance spectroscopy(SS-IS)was used to investigate the influence of structural modifications resulting from the addition of Nb2O5 on the dielectric properties and relaxation processes in the quaternary mixed glass former(MGF)system 35Na_(2)O–10V_(2)O_(5)–(55-x)P_(2)O_(5)–xNb_(2)O_(5)(x=0–40,mol%).The dielectric parameters,including the dielectric strength and dielectric loss,are determined from the frequency and temperature-dependent complex permittivity data,revealing a significant dependence on the Nb2O5 content.The transition from a predominantly phosphate glass network(x<10,region I)to a mixed niobate–phosphate glass net-work(10≤x≤20,region II)leads to an increase in the dielectric parameters,which correlates with the observed trend in the direct-cur-rent(DC)conductivity.In the predominantly niobate network(x≥25,region III),the highly polarizable nature of Nb5+ions leads to a fur-ther increase in the dielectric permittivity and dielectric strength.This is particularly evident in Nb-40 glass-ceramic,which contains Na_(13)Nb_(35)O_(94) crystalline phase with a tungsten bronze structure and exhibits the highest dielectric permittivity of 61.81 and the lowest loss factor of 0.032 at 303 K and 10 kHz.The relaxation studies,analyzed through modulus formalism and complex impedance data,show that DC conductivity and relaxation processes are governed by the same mechanism,attributed to ionic conductivity.In contrast to glasses with a single peak in frequency dependence of imaginary part of electrical modulus,M″(ω),Nb-40 glass-ceramic exhibits two distinct contributions with similar relaxation times.The high-frequency peak indicates bulk ionic conductivity,while the additional low-fre-quency peak is associated with the grain boundary effect,confirmed by the electrical equivalent circuit(EEC)modelling.The scaling characteristics of permittivity and conductivity spectra,along with the electrical modulus,validate time-temperature superposition and demonstrate a strong correlation with composition and modification of the glass structure upon Nb_(2)O_(5) incorporation.

An Energy Saving Glass Deep Processing Line Put into Production in Hubei

On July 16, 2013, the first low-E energy saving glass deep processing line of Hubei Zhongyi Glass Co., Ltd. was put into production in Changyang County of Hubei Province. Low-E glass is a kind of new glass featured with good lighting, thermal insulation, and ultraviolet radiation resistance. So far contracts worth about CNY 50 million have been signed.

Application of semisolid process to Zr-based metallic glass matrix composites

The effect of the cooling slope on the structure of Zr-based metallic glass matrix composites was investigated by changing the cooling slope.The synthesis of bulk metallic glass composites was made by a process combining cooling slope casting and Cu mold casting for Zr66.4Nb6.4Cu10.5Ni8.7Al8 alloys.The results show that the semisolid slurry which consists of the spheroidal or rosette-type BCC crystals and the liquid phase which forms metallic glass phase can be formed by the cooling slope process in this alloy system.However,the semisolid slurry cannot reach to the mold.It is considered that higher viscosity of the liquid phase which forms metallic glass phase causes this result.Thus,parameters of the cooling slope have to be examined further.

Complex Processing of Pulverized Fly Ash by Dry Separation Methods

Pulverized fly ash (PFA) is produced about 500 billions tons every year in the world in a result of coals combustion. Most of the fly ash collected in power plants is disposed by deposition in landfills, situated as a rule near big cities with well developed infrastructure and high cost of land. Moreover, the pollution of environmental by fine solid wastes is inevitable and takes place in area of residing of a basic part of the population. The only solution is a complex processing of fine wastes with a production of value added materials. New conception of complex processing of PFA is proposed on the base of facilities of Electro-mass-classifier (EMC) and other techniques. The characterization of separated fractions was carried out by SEM and optic microscopy, XRD, laser diffraction, M?ssbauer spectroscopy and other methods. A fine fraction of glass microspheres presents the main interest as filler in various materials.

Platinum/rhodium Alloy Bushing for Drawing Glass Fibers in Centrifugal-spinneret-blow Process

In this paper,glass fibers were prepared by centrifugal-spinneret-blow(CSB) process.The molten glass got different flow rate from 390 kg/h to 270 kg/h by adjusting the electric current of platinum/10 rhodium alloy bushing.The diameter and microstructure of glass fibers have been investigated by scanning electron microscopy(SEM) and vertical optical microscope(VOM).The results indicated that the flow rate of molten glass was proportional to the diameter of glass fibers when the molten glass got main flow rate of 330 kg/h.The lower the flow rate was,the finer the average diameter was.

Mineral Processing of Silica Sand in Hanout Area/South of Jordan

White sandstone samples from Hanout area of Late Cambrian-Early Ordovician sandstone in south of Jordan were studied and assessed as a source of glass sand. Upgrading the sand included removing or reducing the content of the contaminant oxides and the heavy minerals. The aim of this research was to achieve this upgrading by examining the best-suited and cost-effective processing method(s) with sufficient product recovery. Following the initial sample characterisation at “bench scale”, a pilot study was performed. A high-grade Glass Sand product of 500 - 125 μm size fraction was produced by wet screening, attrition scrubbing and the separation of heavy minerals using spirals. The high quality Glass Sand product compared well with Grade-A of the British Standard for glass sand. Due to the relatively low level of impurities in the raw material, a substantial silica sand recovery was produced with a high silica grade. The silica sand product was capable to be used in the high quality glass industry and in many other applications where pure silica is required. The mass flowrate of the feeds and the products in the spiral was calculated for the bulk sample as well as the amount of water required operating the process.

High-precision multi-focus laser sculpting of microstructured glass

Precision sculpting of glass with defined surface microstructures is vital due to the miniaturization and integration of glass-based devices,while it is still challenging as the high brittleness of glass.We here create a three-dimensional multifocus laser for glass micro-sculpting through a beam-shaping technology based on the superposition of lens and grating phase diagrams.The multi-focus laser modification in tandem with chemical etching enables the fabrication of glass microstructures with highly adjustable profiles.Refractive-index-induced deviations are migrated via algorithm correction to ensure multi-focus positional accuracy.Energy un-uniformity due to equidistant laser spots arrangement is eliminated through their coordinate randomization following the target profiles.Finally,uniform laser spots with a proper point-topoint distance create connected cracks inside glass,enabling efficient etching with enhanced rates along the modified profile and the fabrication of surface microstructures.We demonstrate diverse groove arrays with profiles of trapezoid,semicircle,and triangle,revealing low roughness around 1.3μm,a high depth-width ratio of 3:1,and depth up to 300μm,which underscore broad applications such as fiber packaging.

Characterization and Performance of Magnesium Doped Bioactive Glass Nanoparticles

The bioactive glass and related biomaterials have become increasingly popular, and have also attracted the research interest of many researchers in recent years due its special performance and tissue engineering application. In this study, to create a material with a variety of properties Mg doped hollow bioactive glass (Mg-HBG) of 80SiO2-5P2O5-10CaO-5MgO system had been produced by using a sol-gel method. The porous structure nanoparticles were specifically made by employing the cetyltrimethylammonium bromide (CTAB) as a surfactant. Magnesium was selected as a doped material with HBG, because it is the most existing cations in the human body which helps for bone metabolism as well as it has antibacterial property. Based on different investigations resulted nanoparticle with the inclusion of the lower molar fractions magnesium has good tested result. For a drug model vancomycin hydrochloride (VAN) was used in this study and it has also good antibacterial activity effect. These findings help the possibility of using Mg-HBG nanoparticles to treat infectious bone abnormalities by demonstrating their compatibility with antibiotics, drug loading and release behavior.

超薄柔性玻璃狭缝下拉法的拉薄行为

狭缝下拉法是制备超薄柔性玻璃的一种新颖方法,对其成形拉薄机理还缺乏足够认识。在考察成形过程的基础上,运用流体力学和传热学原理,提出了其牵伸拉薄行为的一个简单数学模型,并用数值方法进行了求解。探讨了牵引辊牵引速度和狭缝口宽度对牵伸拉薄行为的影响。计算结果与文献中发现的拉薄变化规律相吻合,表明所提出的模型抓住了问题的主要方面,是基本合理的。所得结果对提升该技术的认识有积极作用。

浅谈高铝汽车玻璃及其生产工艺

结合高铝玻璃在汽车应用的现状,综述了高铝玻璃在汽车玻璃应用的优势,并探讨了高铝玻璃在汽车与盖板玻璃的工艺差别,对高铝汽车玻璃的强化工艺、破碎后形态的控制及淋子变形问题的控制难点进行了重点阐述,为高铝汽车玻璃生产工艺的完善提供参考。

Sol-gel preparation and phosphorescence property of Mn^(2+)-doped zinc boro-silicate glass thin films

Mn2＋-doped zinc borosilicate （ZBSM） glass thin films were first synthesized by sol-gel method. In the experiment, a thin gel film was depos-ited onto quartz glass substrates by dip-coating method and then heat-treated to form a Mn2＋-doped zinc borosilicate glass thin film. Long lasting phosphorescence （LLP） and photo-stimulated long lasting phosphorescence （PSLLP） were found in the film sample. According to fluorescence spectra, LLP emission spectra, and PSLLP emission spectra, both LLP and PSLLP emissions are attributed to the energy level transition of 4Eg→4A1g from Mn2＋. Both the phosphorescence intensity decay curves contain a fast decay component and another slow decay one. The thermoluminescence （TL） spectra show that the sample has two kinds of traps at least and their energy level values are about 0.8 eV and 1.02 eV, which could be estimated by the Randall and Willcins formula. The infrared absorption spectra （IR） consist of characteristic vi-bration bands of Si-O-Si, Si-O-Zn, B-O in [BO3], B-O group, and Zn-O in [ZnO4]. Moreover, image storage and logical operation of the ZBSM film were carried out successfully through an experiment analogues of optical storage.

Deformation Analysis of Micro/Nano Indentation and Diamond Grinding on Optical Glasses

The previous research of precision grinding optical glasses with electrolytic in process dressing （ELID） technology mainly concentrated on the action of ELID and machining parameters when grinding, which aim at generating very ＂smoothed＂ surfaces and reducing the subsurface damage. However, when grinding spectrosil 2000 and BK7 glass assisted with ELID technology, a deeply comparative study on material removal mechanism and the wheel wear behaviors have not been given yet. In this paper, the micro/nano indentation technique is initially applied for investigating the mechanical properties of optical glasses, whose results are then refereed to evaluate the machinability. In single grit diamond scratching on glasses, the scratching traces display four kinds of scratch characteristics according to different material removal modes. In normal grinding experiments, the result shows BK7 glass has a better machinability than that of spectrosil 2000, corresponding to what the micro/nano indentation vent revealed. Under the same grinding depth parameters, the smaller amplitude of acoustic emission （AE） raw signals, grinding force and grinding force ratio correspond to a better surface quality. While for these two kinds of glasses, with the increasing of grinding depth, the variation trends of the surface roughness, the force ratio, and the AE raw signals are contrary, which should be attributed to different material removal modes. Moreover, the SEM micrographs of used wheels surface indicate that diamond grains on the wheel surface after grinding BK7 glass are worn more severely than that of spectrosil 2000. The proposed research analyzes what happened in the grinding process with different material removal patterns, which can provide a basis for producing high-quality optical glasses and comprehensively evaluate the surface and subsurface integrity of optical glasses.

Generalized model for laser-induced surface structure in metallic glass

The details of the special three-dimensional micro-nano scale ripples with a period of hundreds of microns on the surfaces of a Zr-based and a La-based metallic glass irradiated separately by single laser pulse are investigated.We use the small-amplitude capillary wave theory to unveil the ripple formation mechanism through considering each of the molten metallic glasses as an incompressible viscous fluid.A generalized model is presented to describe the special morphology,which fits the experimental result well.It is also revealed that the viscosity brings about the biggest effect on the monotone decreasing nature of the amplitude and the wavelength of the surface ripples.The greater the viscosity is,the shorter the amplitude and the wavelength are.

The Values ＆ Benefits of Umicore＇s Process Excellence Model

We will highlight the values Umicore's unique Process Excellence Model is based upon and how these do correlate with the overall culture of Umicore. Besides, we are going to explain about the benefits for the target industries that come along with our approach. Here, we will not mainly focus on the usually mentioned cost saving potential, but how also other aspects do create substantial value for the industries.

Effects of infiltration parameters on mechanical and microstructural properties of tungsten wire reinforced Cu_(47)Ti_(33)Zr_(11)Ni_6Sn_2Si_1 metallic glass matrix composites

Cu47Ti33Zr11Ni6Sn2Si1-based bulk metallic glass matrix composites reinforced with tungsten wires were fabricated by infiltration process at different temperatures （850, 900, 950 and 1000 °C） and time （10, 20 and 30 min） in a quartz or a steel tube. The mechanical tests were carried out by scanning electron microscopy （SEM） and X-ray diffraction （XRD）. The results show that the maximum strength and total strain of the composite are 1778 MPa and 2.8% fabricated in steel tube at 900 °C for 10 min, and 1582 MPa and 3.6% fabricated in quartz tube at 850 °C for 10 min, respectively.

Thermal Analysis and Immobilisation of Spent Ion Exchange Resin in Borosilicate Glass

The underground disposal of waste arising from the nuclear industry needs constant evaluation in order to improve upon it through minimizing the volume and cost by reducing the amount of glass used without compromising the safety of any leakage from the radioactive waste form. The immobilization of the spent resin (NRW-40) in borosilicate glass was investigated to meet the acceptance criteria for disposal of nuclear waste. The organic mixed bed resin in granular form was used as a waste target. The analysis of surrogate resin doped with radioactive and non-radioactive cesium (Cs) and cobalt (Co) was carried out to investigate their thermal and chemical properties and their compatibility with an alkaline borosilicate glass. The thermal analysis indicates that the structural damage caused by 1 mSv gamma radiation to the radioactive resin has altered its properties in comparison with the non-radioactive resin, same amount of cesium (8.88 wt%) and cobalt (1.88 wt%) were used in both resins. The immobilization of residue shows that the excess sulfur in the residue caused phase crystallization in the final glass matrix. It was found that the volatilization of Cs-137 and Co-60 from the successful radioactive resin-glass matrix (HG-3-IER-500) were more than that in the non-radioactive resin-glass matrix (HG-3-IEX-500). The study demonstrates comprehensive experimental and analytical works and shows that it is possible to minimise the volume of the waste while keeping the required safety levels, however further research needs to be carried out in this area.

A review on glass welding by ultra-short laser pulses

Glass welding by ultra-short pulsed(USP)lasers is a piece of technology that offers high strength joints with hermetic sealing.The joints are typically formed in glass that is transparent to the laser by exploiting nonlinear absorption effects that occur under extreme conditions.Though the temperature reached during the process is on the order of a few 1000°C,the heat affected zone(HAZ)is confined to only tens of micrometers.It is this controlled confinement of the HAZ during the joining process that makes this technology so appealing to a multitude of applications because it allows the foregoing of a subsequent tempering step that is typically essential in other glass joining techniques,thus making it possible to effectively join highly heat sensitive components.In this work,we give an overview on the process,development and applications of glass welding by USP lasers.

A Review of Glass and Crystallizations of Glass-Ceramics

The fundamental science behind glass and glass-ceramics in relation to research including syntheses, processing, characterization and applications are critically reviewed in this paper. The crystalline structure of the crystalline phases/s investigated in the literature is also discussed. Throughout this paper, the scene is set toward the overall picture of the rationale behind the choice of a glass system. Additionally, earlier reviews do not include the most recent literature in this fast-moving field. The main methods of synthesizing glasses and glass-ceramics are explained and described in relation to their applications. The paper concludes with recommendations for future research.

Angular Dependence of the Second Harmonic Generation Induced by Femtosecond Laser Irradiation in Silica-Based Glasses:Variation with Writing Speed and Pulse Energy

To control second harmonic generation (SHG) in silica-based glasses is crucial for fabricating photonic devices, such as frequency doubling waveguides. Here, we investigated SHG of laser induced nonlinear optical crystals in silica-based glasses, according to writing speed and pulse energy. We observed two regions with different probing laser polarization angular dependence: a) a well-defined cosine-like curve with period of 180° at low pulse energy (0.8 μJ) whatever the writing speed or at high pulse energy (1.4 μJ) with high writing speed (25 μm/s). This is accounted for by a well-defined texture for the nano crystals with their polar axis oriented perpendicular to the writing laser polarization;and b) a double cosine-like curve revealing a second texture of the crystals at high pulse energy (1.4 μJ) with low writing speed (5 μm/s) and with the polar axis oriented closer parallel to the writing laser polarization. Therefore, a SHG dependence on probing laser polarization angle may show high contrast by a correct choice of the writing speed and pulse energy. These results pave the way for elaboration of nonlinear optical devices.

蓝宝石玻璃超声振动辅助磨削试验研究

为了探究烧结磨头不同磨头参数和磨削参数对蓝宝石玻璃磨削特性的影响,综合考虑了磨头粒度号、主轴转速、进给速度、磨削深度等因素,设计并开展了非超声和超声振动辅助磨削加工试验,研究了上述因素对蓝宝石磨削表面粗糙度、表面形貌及磨削力的影响。结果表明,超声和非超声磨削工况中,磨头粒度号增大对磨削力和表面粗糙度的影响整体均呈现先增大后减小的趋势。不同磨头粒度号工况下的超声磨削力和表面粗糙度普遍小于非超声结果,磨削力最大降幅为27.2%,表面粗糙度最大降幅为18.6%;采用粒度号200/230#的磨头进行磨削,可获得相对较小的切削力和表面粗糙度,是研究工况下的最佳粒度号,而140/170#的使用效果最差。相比于非超声磨削,超声可在所选的主轴转速、进给速度和磨削深度条件下实现磨削力和表面粗糙度不同程度的降低,在小主轴转速和小磨削深度工况下,超声磨削对蓝宝石表面质量的改善作用更显著。