Adaptive Gain Tuning Rule for Nonlinear Sliding-mode Speed Control of Encoderless Three-phase Permanent Magnet Assisted Synchronous Motor

In this paper, an adaptive gain tuning rule is designed for the nonlinear sliding mode speed control(NSMSC) in order to enhance the dynamic performance and the robustness of the permanent magnet assisted synchronous reluctance motor(PMa-Syn RM) with considering the parameter uncertainties. A nonlinear sliding surface whose parameters are altering with time is designed at first. The proposed NSMSC can minimize the settling time without any overshoot via utilizing a low damping ratio at starting along with a high damping ratio as the output approaches the target set-point. In addition, it eliminates the problem of the singularity with the upper bound of an uncertain term that is hard to be measured practically as well as ensures a rapid convergence in finite time, through employing a simple adaptation law. Moreover, for enhancing the system efficiency throughout the constant torque region, the control system utilizes the maximum torque per ampere technique. The nonlinear sliding surface stability is assured via employing Lyapunov stability theory. Furthermore, a simple sliding mode estimator is employed for estimating the system uncertainties. The stability analysis and the experimental results indicate the effectiveness along with feasibility of the proposed speed estimation and the NSMSC approach for a 1.1-k W PMa-Syn RM under different speed references, electrical and mechanical parameters disparities, and load disturbance conditions.

Speed Regulation Method Using Genetic Algorithm for Dual Three-phase Permanent Magnet Synchronous Motors

Dual three-phase Permanent Magnet Synchronous Motor(DTP-PMSM)is a nonlinear,strongly coupled,high-order multivariable system.In today’s application scenarios,it is difficult for traditional PI controllers to meet the requirements of fast response,high accuracy and good robustness.In order to improve the performance of DTP-PMSM speed regulation system,a control strategy of PI controller based on genetic algorithm is proposed.Firstly,the basic mathematical model of DTP-PMSM is established,and the PI parameters of DTP-PMSM speed regulation system are optimized by genetic algorithm,and the modeling and simulation experiments of DTP-PMSM control system are carried out by MATLAB/SIMULINK.The simulation results show that,compared with the traditional PI control,the proposed algorithm significantly improves the performance of the control system,and the speed output overshoot of the GA-PI speed control system is smaller.The anti-interference ability is stronger,and the torque and double three-phase current output fluctuations are smaller.

Rotor Strength Analysis of High-speed Permanent Magnet Synchronous Motors

为了对转子进行有效的冷却，在满足电机电磁性能的前提下，可通过减小保护套的厚度来尽可能增大定转子之间的气隙，因而必须对保护套和永磁体进行强度校核。将转子受力状况简化为平面应变问题，在此基础上推导出了两层过盈配合、三层过盈配合转子的应力场、应变场、位移场的解析公式，并利用有限元方法验证了解析公式的正确性。归纳了高速情况下热套式永磁转子强度设计准则，为转子的优化设计提供了理论依据。以一台额定转速120kr／min、10kW的高速永磁同步电机为例，给出了两种常用过盈配合高速电机转子的强度设计方法。

Analysis for Rotor Losses of High Speed Permanent Magnet Synchronous Motor

This paper presents an analysis based on analytical method for solid rotor motors for determining the rotor eddy current losses due to the current harmonics of the stator winding. The accuracy of the analytical results is verified by experiments.

Speed sensorless FCS-MPTC based on FOSM-MRAS five-phase permanent magnet synchronous motor

For the two-level five-phase permanent magnet synchronous motor(FP-PMSM)drive system,an improved finite-control-set model predictive torque control(MPTC)strategy is adopted to reduce torque ripple and improve the control performance of the system.The mathematical model of model reference adaptive system(MRAS)of FP-PMSM is derived and a method based on fractional order sliding mode(FOSM)is proposed to construct the model reference adaptive system(FOSMMRAS)to improve the motor speed estimation accuracy and eliminate the sliding mode integral saturation effect.The simulation results show that the FP-PMSM speed sensorless FCS-MPTC system based on FOSM-MRAS has strong robustness,good dynamic performance and static performance,and high reliability.

Vector control of permanent magnet synchronous motor based on dynamic matrix control

Aiming at the control problem of strongly nonlinear and coupled permanent magnet synchronous motor(PMSM)oil rig,this paper presents a predictive control method based on dynamic matrix model.In this method,the dynamic matrix algorithm using multistep prediction technique is applied to the speed loop control of the motor vector control.And its control effect is compared with the traditional proportional integral(PI)control of the motor.By comparing the initial dynamic response and the steady-state recovery under load interference of the two methods,it is shown that the dynamic response and the robustness of the motor controlled by the new method is better than that controlled by conventional PI method.And the feasibility of new control in the application of PMSM oil rig is verified.

A Sensor-less Surface Mounted PMSM for Electronic Speed Control in Multilevel Inverter

Recent advancements in power electronics technology evolves inverter fed electric motors.Speed signals and rotor position are essential for controlling an electric motor accurately.In this paper,the sensorless speed control of surface-mounted permanent magnet synchronous motor(SPMSM)has been attempted.SPMSM wants a digital inverter for its precise working.Hence,this study incor-poratesfifteen level inverter to the SPMSM.A sliding mode observer(SMO)based sensorless speed control scheme is projected to determine rotor spot and speed of the multilevel inverter(MLI)fed SPMSM.MLI has been operated using a multi carrier pulse width modulation(MCPWM)strategy for generation offif-teen level voltages.The simulation works are executed with MATLAB/SIMU-LINK software.The steadiness and the heftiness of the projected model have been investigated under no loaded and loaded situations of SPMSM.Furthermore,the projected method can be adapted for electric vehicles.

一种自适应扩展卡尔曼滤波的永磁同步电机无位置传感器矢量控制

在粗差干扰或噪声统计偏差情况下,扩展卡尔曼滤波(EKF)对永磁同步电机(PMSM)的速度和转子位置估计存在精度下降问题,为此提出一种基于新息序列的自适应扩展卡尔曼滤波算法(AEKF)。首先,将粗差干扰加入系统观测方程中,分析粗差干扰对系统观测精度的影响。其次,为增强算法的抗扰性能,在新息协方差计算中设置加权系数,通过调整临近时刻的新息协方差阵权重,计算出新息协方差值,并更新到卡尔曼增益的计算。最后,建立AEKF数学模型,并对比粗差干扰与噪声统计出现偏差情况下,AEKF与EKF两种策略的观测性能。仿真和实验结果表明,在粗差干扰或噪声统计信息出现偏差情况下,AEKF算法对永磁同步电机转速的观测具备更强的鲁棒性及更高的预测精度。

基于滑模观测器的高速PMSM无传感器控制

针对基于饱和函数滑模观测器方法存在调节参数多及低通滤波器带来的相位延迟问题,研究一种基于超螺旋算法的滑模观测器无传感器控制策略,通过理论推导及系统稳定性分析,设计了一种滑模系数根据转速变化在线调节的自适应滑模系数算法。通过实验验证了该方法相比于基于饱和函数滑模观测器,能在较宽速度范围内有效地抑制抖振,提高了无传感器控制系统的估计精度,简化了参数调节过程及滤波器设计环节。

PMSM无模型滑模转速无差拍电流预测控制

针对传统永磁电机调速系统易受到参数摄动影响而导致控制精度下降的问题,提出一种基于扩张状态观测器(ESO)的永磁同步电机(PMSM)无模型滑模转速无差拍电流预测控制策略。首先用参数摄动下的PMSM调速系统数学模型归纳出系统对应的超局部模型,然后结合无差拍预测控制思想设计了电流环控制器,采用两步预测算法解决了传统无差拍算法存在的延时问题,并且提出校正算法进一步抑制实际的预测误差;利用变速率指数滑模趋近率设计了新型无模型滑模速度控制器,减弱抖振的同时提高了系统响应速度;并设计ESO对参数失配和扰动进行估计和补偿。最后,通过仿真与半实物实验验证了所提控制策略的有效性。

永磁同步电机新型趋近律滑模控制器设计

针对传统指数趋近律因函数不连续性引起抖振、趋近速度与抖振抑制之间无法同时满足高性能控制系统要求的问题,提出基于系统状态变量的新型滑模趋近律,并应用于永磁同步电机速度、电流控制器中。趋近律引入系统状态变量幂次项和状态变量的双曲正弦值,使系统状态变量以等速和指数2种速率趋向切换面,可以加快系统到达切换面的速度,当系统接近切换面时,指数项接近于0,等速项开始起关键作用,对系统的抖振进行抑制。同时采用双曲正切开关函数替代符号函数,以去除因函数的不连续性所引起的抖振问题。既能提高系统到达滑模面的速度,又能有效抑制固有抖振,提升系统的动态性能。仿真和实验结果表明,新型趋近律相比于传统指数趋近律能够有效降低永磁同步电机启动时转速超调,提高系统的响应速度,抑制系统的抖振。

永磁同步电机非线性增益非奇异快速终端滑模控制

为了研究传统滑模控制中系统误差在有限时间内无法收敛至0以及传统滑模控制中系统抖振与收敛速度互不兼容的问题,提出一种非奇异快速终端滑模控制与扰动观测器结合的速度控制器。通过将参数可变的非线性函数作为增益代替固定增益加入滑模控制策略中从而改善系统响应速度同时减小系统的抖振。针对转矩扰动对系统的影响,加入负载转矩扰动观测器并补偿到q轴电流中以进一步提高控制器抗负载扰动能力。根据李雅普诺夫稳定性理论对提出的新型滑模控制器进行稳定性证明,经过仿真和实验证明,电机在启动时响应快、无超调且抖振较小,在突加转矩时转速波动小且恢复时间迅速,证明了改进后的变增益非奇异终端滑模控制与传统非奇异快速终端滑模控制策略相比可以提高动态性能的同时抑制系统抖振、增强系统的鲁棒性。

无人机17kW电机振动噪声分析与巡航转速下尖端噪声优化

随着无人机的迅速发展,噪声问题影响消费者体验及AI交互、语音识别等技术,限制了无人机应用潜力。该文针对一台17 kW无人机用外转子永磁同步电机进行研究。为降低电机尖端振动噪声,且保留原电机电磁性能,重点提出优化磁极和定子开槽的方法。具体以平均转矩、转矩脉动等作为约束条件,构建多目标优化数学模型,并利用混合粒子群优化算法求解。该文深入探讨磁极参数、定子开槽对低阶次径向气隙磁通密度空间谐波特征的影响。并对电机转子模态仿真,以研究径向电磁力与空间模态的作用机理。在多转速情况下,以巡航转速为重点,分析整体电机电磁振动噪声特征。最后,仿真和实验结果表明,电机在巡航转速下的尖端噪声显著减小。验证了优化结构对无人机电机尖端振动噪声有明显抑制作用,对解决无人机噪声问题具有重要意义。

Backstepping Control of Speed Sensorless Permanent Magnet Synchronous Motor Based on Slide Model Observer

This paper presents a backstepping control method for speed sensorless permanent magnet synchronous motor based on slide model observer. First, a comprehensive dynamical model of the permanent magnet synchronous motor(PMSM) in d-q frame and its space-state equation are established. The slide model control method is used to estimate the electromotive force of PMSM under static frame, while the position of rotor and its actual speed are estimated by using phase loop lock(PLL) method. Next,using Lyapunov stability theorem, the asymptotical stability condition of the slide model observer is presented. Furthermore, based on the backstepping control theory, the PMSM rotor speed and current tracking backstepping controllers are designed, because such controllers display excellent speed tracking and anti-disturbance performance. Finally, Matlab simulation results show that the slide model observer can not only estimate the rotor position and speed of the PMSM accurately, but also ensure the asymptotical stability of the system and effective adjustment of rotor speed and current.

应用于PMSM调速系统的改进超螺旋滑模控制

针对永磁同步电机(PMSM)易受外界扰动和参数不确定性的影响,此处设计了一种改进超螺旋滑模控制策略。该方法采用一种准滑动模态中的连续函数来替代符号函数,以克服传统滑模控制存在的抖振问题,并将比例控制和积分控制引入超螺旋滑模控制来提高控制系统对负载和参数变化的鲁棒性,采用Lyapunov函数对控制系统进行稳定性分析。实验结果表明,所设计的改进滑模控制器能有效抑制控制系统的抖振,实现控制系统的快速跟随和无超调工作,增强了系统的鲁棒性。

基于FOA优化PID参数的永磁同步电机转速控制

为提高永磁同步电机转速控制的效果,提出一种基于果蝇优化算法(Fruit Fly Optimization Algorithm,FOA)优化比例积分微分控制(proportional-integral-derivative control)的方法。其中,以PMSM调速系统为背景,构建调速系统的PID方法,然后构建FOA优化PID参数的PID控制器,以实现永磁同步电机转速系统的自适应控制。仿真结果表明,FOA-PID方法具有响应速度快、超调小、抗干扰能力和速度调节能力强的特点,在固定负载改变转速条件下,仅需0.02 s即可达到稳定状态,有效改善了永磁同步电机转速控制系统的控制性能;相较于标准PID和RBF-PID方法,FOA-PID方法在正向起动转速情况下的超调量为1.36%,分别低5.73%和1.12%;在负向起动转速情况下,FOA-PID方法的最大超调量为0.56%,分别低15.13%和8.22%。由此得出,本FOA-PID方法可行,具有一定的优越性。

飞轮储能技术在断路器动态特性检测中的应用

在地铁列车断路器动态特性检测中,引入飞轮储能系统能够有效回收列车再生制动能量,稳定断路器开关动作电压,但单飞轮储能系统容量较小,难以满足列车再生制动能量利用需求,飞轮储能阵列(FESA)是解决这一问题的有效手段.首先,分析飞轮储能系统的数学模型和运行特性;然后,考虑稳压节能及弱磁需求,给出基于多电压阈值的单飞轮储能系统控制策略,并在此基础上针对飞轮阵列均速控制和工作模式管理等核心问题,提出基于转差修正控制和基于“电压-转速-电流”三闭环控制的两种飞轮储能阵列控制策略;最后,通过仿真和实验验证飞轮储能阵列控制策略的可行性.

A sensorless efficiency test system for a high-speed permanent magnet synchronous motor

We present a sensorless efficiency test system with energy recovery for a high-speed permanent magnet synchronous motor(PMSM). In the system, two identical high-speed PMSMs are used as the motor under test(MUT)and the load machine(LM),respectively.A new sensorless vector control(VC) method based on a hypothetical reference frame is presented to control both the MUT and the LM.Also,a regenerating unit is used to implement energy circulation to save energy.Experiments were carried out on a prototype, with a digital controller based on the TMS320 F28335, to verify the adequacy of the sensorless VC method.As a result,the efficiency test system achieves the load test at the speed of 21000 r/min without any reduction equipment. During the test, the energy regenerated by the LM could be fed back to the MUT by the regenerating unit, and 81.31% electrical power was saved.In addition, with the proposed sensorless VC method,both the MUT and the LM can work at i_d = 0 without a position sensor.

永磁同步电机无位置传感器控制技术综述

无位置传感器电机驱动器具有成本低、可靠性高、硬件电路简单以及维护要求少等优势,在学术界和工业应用中受到了越来越多的关注。对适用于零低速域、中高速域以及全速域三种运行范围的多种无位置传感器技术进行了综述。首先,分别对比分析了零低速域和中高速域下各种无位置传感器控制方法的优缺点。其次,梳理和总结了目前全速域运行的切换控制策略。最后,对永磁同步电机无位置控制技术的未来发展趋势进行了展望,并指出了后续研究的关键问题。

低载波比下基于状态反馈和大林算法的永磁同步电机高性能电流控制策略

受到功率器件开关频率的限制,高速永磁同步电机驱动系统通常需要低载波比运行,此时系统延时相对很大,对电流环设计要求很高。常规在连续域设计的复矢量PI控制器由于离散化实现存在误差,dq轴解耦不完全,而且扰动传递函数包含电机自身低阻尼比极点,使系统抗干扰能力差,尤其是负基波频率附近的扰动。因此,文中提出状态反馈大林控制算法。首先,利用延时环节电压进行反馈来使系统完全解耦;然后,通过输出电流反馈提升系统阻尼来抑制扰动;最后,对解耦且阻尼后的系统设计大林控制器来提升稳定裕度。实验结果表明,相较于复矢量PI控制器,所提出的状态反馈大林控制器dq轴解耦性能好,电流超调小,系统振荡小,且抗扰能力显著提升。