In order to improve the machining ac cu racy of spiral bevel gear,difference surface was adopted to characterize its gl obal form deviations quantifiably and correct its deviations.The theoretical to oth surface model...In order to improve the machining ac cu racy of spiral bevel gear,difference surface was adopted to characterize its gl obal form deviations quantifiably and correct its deviations.The theoretical to oth surface model of spiral bevel gear was built,and the actual tooth surface o f spiral bevel gear had been got by using latticed measurement.The equation of difference surface which can characterize the actual tooth surface deviation s was built by means of mathematical method in combination with measurement prin ciple.The quantitative mathematical relationship between the actual tooth surfa ce deviations of spiral bevel gear and the corrected values of the machine-sett ing parameters had been referred,and the theoretical correction formula of the global form deviations had been got by the least square method.Finally,the pinion of spiral bevel gear in the automobile rear axle has been set for an exam ple to account for the effectiveness of the deviation correction by use of the d ifference surface method.展开更多
Although a great deal of research has been dedicated to the synthesis of spiral bevel gears, little related to reverse engineering can be found. An approach is proposed to reverse the machine-tool settings of the pini...Although a great deal of research has been dedicated to the synthesis of spiral bevel gears, little related to reverse engineering can be found. An approach is proposed to reverse the machine-tool settings of the pinion of a spiral bevel gear drive on the basis of the blank and tooth surface data obtained by a coordinate measuring machine(CMM). Real tooth contact analysis(RTCA) is performed to preliminary ascertain the contact pattern, the motion curve, as well as the position of the mean contact point. And then the tangent to the contact path and the motion curve are interpolated in the sense of the least square method to extract the initial values of the bias angle and the higher order coefficients(HOC) in modified roll motion. A trial tooth surface is generated by machine-tool settings derived from the local synthesis relating to the initial meshing performances and modified roll motion. An optimization objective is formed which equals the tooth surface deviation between the real tooth surface and the trial tooth surface. The design variables are the parameters describing the meshing performances at the mean contact point in addition to the HOC. When the objective is optimized within an arbitrarily given convergence tolerance, the machine-tool settings together with the HOC are obtained. The proposed approach is verified by a spiral bevel pinion used in the accessory gear box of an aviation engine. The trial tooth surfaces approach to the real tooth surface on the whole in the example. The results show that the convergent tooth surface deviation for the concave side on the average is less than 0.5 μm, and is less than 1.3 μm for the convex side. The biggest tooth surface deviation is 6.7 μm which is located at the corner of the grid on the convex side. Those nodes with relative bigger tooth surface deviations are all located at the boundary of the grid. An approach is proposed to figure out the machine-tool settings of a spiral bevel pinion by way of reverse engineering without having known the theoretical tooth surfaces and the corresponding machine-tool settings.展开更多
The phenomena of interference in the course of assembling curved bevel gears are ana. lysed and the corresponding prediction program of interference is established taking KlingInberg bevel gear as an exmple....The phenomena of interference in the course of assembling curved bevel gears are ana. lysed and the corresponding prediction program of interference is established taking KlingInberg bevel gear as an exmple. The factors influencing interferenee are discussed and the coneept ofcritical cutter radius is proposed. Finally, a simplified approximate function between the critical cutter ra- dius and the other factors is derived,and the designing method of avoiding interferenee is provided. The analysis and caiculation are proved to consistent with a case of actual product.展开更多
基金National Natural Science Foundation of China(No.50976108)
文摘In order to improve the machining ac cu racy of spiral bevel gear,difference surface was adopted to characterize its gl obal form deviations quantifiably and correct its deviations.The theoretical to oth surface model of spiral bevel gear was built,and the actual tooth surface o f spiral bevel gear had been got by using latticed measurement.The equation of difference surface which can characterize the actual tooth surface deviation s was built by means of mathematical method in combination with measurement prin ciple.The quantitative mathematical relationship between the actual tooth surfa ce deviations of spiral bevel gear and the corrected values of the machine-sett ing parameters had been referred,and the theoretical correction formula of the global form deviations had been got by the least square method.Finally,the pinion of spiral bevel gear in the automobile rear axle has been set for an exam ple to account for the effectiveness of the deviation correction by use of the d ifference surface method.
基金supported by Aero Propulsion Test and Demonstration of Commission of Science and Technology and Industry for Nation Defense,China (Grant No. APTD-1001B)
文摘Although a great deal of research has been dedicated to the synthesis of spiral bevel gears, little related to reverse engineering can be found. An approach is proposed to reverse the machine-tool settings of the pinion of a spiral bevel gear drive on the basis of the blank and tooth surface data obtained by a coordinate measuring machine(CMM). Real tooth contact analysis(RTCA) is performed to preliminary ascertain the contact pattern, the motion curve, as well as the position of the mean contact point. And then the tangent to the contact path and the motion curve are interpolated in the sense of the least square method to extract the initial values of the bias angle and the higher order coefficients(HOC) in modified roll motion. A trial tooth surface is generated by machine-tool settings derived from the local synthesis relating to the initial meshing performances and modified roll motion. An optimization objective is formed which equals the tooth surface deviation between the real tooth surface and the trial tooth surface. The design variables are the parameters describing the meshing performances at the mean contact point in addition to the HOC. When the objective is optimized within an arbitrarily given convergence tolerance, the machine-tool settings together with the HOC are obtained. The proposed approach is verified by a spiral bevel pinion used in the accessory gear box of an aviation engine. The trial tooth surfaces approach to the real tooth surface on the whole in the example. The results show that the convergent tooth surface deviation for the concave side on the average is less than 0.5 μm, and is less than 1.3 μm for the convex side. The biggest tooth surface deviation is 6.7 μm which is located at the corner of the grid on the convex side. Those nodes with relative bigger tooth surface deviations are all located at the boundary of the grid. An approach is proposed to figure out the machine-tool settings of a spiral bevel pinion by way of reverse engineering without having known the theoretical tooth surfaces and the corresponding machine-tool settings.
文摘The phenomena of interference in the course of assembling curved bevel gears are ana. lysed and the corresponding prediction program of interference is established taking KlingInberg bevel gear as an exmple. The factors influencing interferenee are discussed and the coneept ofcritical cutter radius is proposed. Finally, a simplified approximate function between the critical cutter ra- dius and the other factors is derived,and the designing method of avoiding interferenee is provided. The analysis and caiculation are proved to consistent with a case of actual product.
