Based on a series of previous studies, an experiment on the integral seismic behavior of a 1/3 scaled model of two-bay and three-story reinforced concrete frame with split columns at lower two stories is performed und...Based on a series of previous studies, an experiment on the integral seismic behavior of a 1/3 scaled model of two-bay and three-story reinforced concrete frame with split columns at lower two stories is performed under cyclic loading. The original columns at lower two stories of the model frame are short columns and they are replaced by the split columns. The hysteresis curves between the horizontal cyclic load and the lateral displacement at the top of the model frame, indicate that under the cyclic loading, the model frame undergoes the process of cracking, yielding, and maximum loading before being destroyed at the ultimate load. They also indicate that the model frame has better ductility, and the ratio of the ultimate displacement to the yielding displacement, reaches 6.0. The yielding process of the model frame shows that for the frame with split columns, plastic hinges are generated at the ends of beams and then the columns begin yielding while the frame still possesses the bearing and deformation capacity. The design idea of directly changing the short column to long one in the reinforced concrete frame may be realized by replacing the short column with the split one.展开更多
In this study, the seismic fragility curves of two reinforced concrete（RC） columns that were lap-spliced at the bottom and retrofitted with steel wrapping jackets were generated. Their seismic performance was probab...In this study, the seismic fragility curves of two reinforced concrete（RC） columns that were lap-spliced at the bottom and retrofitted with steel wrapping jackets were generated. Their seismic performance was probabilistically assessed in comparison to that of lap-spliced or continuous reinforcement RC columns. This study used two types of steel wrapping jackets, a full jacket and a split jacket. Analytical models of the four types of columns were developed based on the experimental results of the columns using Open SEES, which is effective in conducting nonlinear time history analyses. A suite of ten artificial ground motions, modified from recorded ground motions, was used to perform nonlinear time history analyses of the analytical models with scaling of the peak ground acceleration from 0.1 g to 1.0 g in increments of 0.1 g. The steel wrapping jackets did not increase the medians for yield（slight damage state） of the lap-spiced column and did not exceed the corresponding median of the continuous reinforcement column. However, the two steel jackets increased the medians for failure by 1.872 and 2.017 times, respectively, and exceeded the corresponding median of the continuous reinforcement column by 11.8% and 20.5%, respectively.展开更多
In this article, one kind of multiple steady states(MSS) phenomenon was investigated for a dividing wall column(DWC). The four-section model constructed in Aspen Plus was employed to simulate two DWC cases: mixture of...In this article, one kind of multiple steady states(MSS) phenomenon was investigated for a dividing wall column(DWC). The four-section model constructed in Aspen Plus was employed to simulate two DWC cases: mixture of n-hexane, n-heptane and n-octane;system of methanol, ethanol and n-propanol. It can be seen that there is a range of vapor split ratio in which multiple solutions of reflux ratio exist for fixed DWC configuration with the same feed and product streams. The width and the curve shapes of the MSS region, and the number of solutions change with the liquid split ratio. This MSS phenomenon was further explained using the component recovery around the prefractionator and the component recycling flow inside the DWC. This MSS phenomenon is helpful for DWC design by knowing the probable existence of multiple solutions in advance.展开更多
For separating some specific four component mixtures into four products, the four-product dividing wall column(FPDWC) with two partition walls can provide the same utility consumption with the extended Petlyuk configu...For separating some specific four component mixtures into four products, the four-product dividing wall column(FPDWC) with two partition walls can provide the same utility consumption with the extended Petlyuk configuration, although with structure simplicity. However, the reluctance to implement this kind of four product dividing wall column industrially also consists in the two uncontrollable vapor splits associated with it. The vapor split ratios are set at the design stage and might not be the optimal value for changed feed composition, thus minimum energy consumption could not be ensured. In the present work, a sequential iterative optimization approach was initially employed to determine the parameters of cost-effective FPDWC. Then the effect of maintaining the vapor split ratios at their nominal value on the energy penalty was investigated for the FPDWC with two partition walls, in case of feed composition disturbance. The result shows that no more than + 2% above the optimal energy requirements could be ensured for 20% feed composition disturbances, which is encouraging for industrial implementation.展开更多
基金Supported by National Science Fund for Distinguished Young Scholars of China( No. 50425824
文摘Based on a series of previous studies, an experiment on the integral seismic behavior of a 1/3 scaled model of two-bay and three-story reinforced concrete frame with split columns at lower two stories is performed under cyclic loading. The original columns at lower two stories of the model frame are short columns and they are replaced by the split columns. The hysteresis curves between the horizontal cyclic load and the lateral displacement at the top of the model frame, indicate that under the cyclic loading, the model frame undergoes the process of cracking, yielding, and maximum loading before being destroyed at the ultimate load. They also indicate that the model frame has better ductility, and the ratio of the ultimate displacement to the yielding displacement, reaches 6.0. The yielding process of the model frame shows that for the frame with split columns, plastic hinges are generated at the ends of beams and then the columns begin yielding while the frame still possesses the bearing and deformation capacity. The design idea of directly changing the short column to long one in the reinforced concrete frame may be realized by replacing the short column with the split one.
基金Basic Science Research Program through the National Research Foundation of Korea funded by the Ministry of Education,Science and Technology under Grant No.2013-005944
文摘In this study, the seismic fragility curves of two reinforced concrete（RC） columns that were lap-spliced at the bottom and retrofitted with steel wrapping jackets were generated. Their seismic performance was probabilistically assessed in comparison to that of lap-spliced or continuous reinforcement RC columns. This study used two types of steel wrapping jackets, a full jacket and a split jacket. Analytical models of the four types of columns were developed based on the experimental results of the columns using Open SEES, which is effective in conducting nonlinear time history analyses. A suite of ten artificial ground motions, modified from recorded ground motions, was used to perform nonlinear time history analyses of the analytical models with scaling of the peak ground acceleration from 0.1 g to 1.0 g in increments of 0.1 g. The steel wrapping jackets did not increase the medians for yield（slight damage state） of the lap-spiced column and did not exceed the corresponding median of the continuous reinforcement column. However, the two steel jackets increased the medians for failure by 1.872 and 2.017 times, respectively, and exceeded the corresponding median of the continuous reinforcement column by 11.8% and 20.5%, respectively.
基金Supported by the National Natural Science Foundation of China(21376240)
文摘In this article, one kind of multiple steady states(MSS) phenomenon was investigated for a dividing wall column(DWC). The four-section model constructed in Aspen Plus was employed to simulate two DWC cases: mixture of n-hexane, n-heptane and n-octane;system of methanol, ethanol and n-propanol. It can be seen that there is a range of vapor split ratio in which multiple solutions of reflux ratio exist for fixed DWC configuration with the same feed and product streams. The width and the curve shapes of the MSS region, and the number of solutions change with the liquid split ratio. This MSS phenomenon was further explained using the component recovery around the prefractionator and the component recycling flow inside the DWC. This MSS phenomenon is helpful for DWC design by knowing the probable existence of multiple solutions in advance.
基金Supported by Open Research Project of State Key Laboratory of Chemical Engineering(SKL-ChE-16B06)Yangtze Scholars and Innovative Research Team in Chinese University(IRT-17R81)
文摘For separating some specific four component mixtures into four products, the four-product dividing wall column(FPDWC) with two partition walls can provide the same utility consumption with the extended Petlyuk configuration, although with structure simplicity. However, the reluctance to implement this kind of four product dividing wall column industrially also consists in the two uncontrollable vapor splits associated with it. The vapor split ratios are set at the design stage and might not be the optimal value for changed feed composition, thus minimum energy consumption could not be ensured. In the present work, a sequential iterative optimization approach was initially employed to determine the parameters of cost-effective FPDWC. Then the effect of maintaining the vapor split ratios at their nominal value on the energy penalty was investigated for the FPDWC with two partition walls, in case of feed composition disturbance. The result shows that no more than + 2% above the optimal energy requirements could be ensured for 20% feed composition disturbances, which is encouraging for industrial implementation.
