Powder in tube process(PIT) was adopted for the fabrication of single filament Bi-2223 tapes, and a heat treatment process including the first heat treatment(HT1), intermediate rolling(IR), and second heat treat...Powder in tube process(PIT) was adopted for the fabrication of single filament Bi-2223 tapes, and a heat treatment process including the first heat treatment(HT1), intermediate rolling(IR), and second heat treatment(HT2) was performed. The phase evolution mechanism and microstructure changes during these heat treatment processes were systematically discussed. The influences of HT1 parameters on the phase evolution process of Bi-2223 tapes were discussed. With the optimized HT1 process, a proper Bi-2223 content of about 90% was achieved. HT2 process was also optimized by adding a post annealing process. An obvious increase of current capacity was obtained due to the enhancement of intergrain connections. Single filament Bi-2223 tapes with the critical current of Ic-90 A were fabricated with the optimized sintering process.展开更多
ZnO films were prepared at different substrate temperatures through spraying pyrolysis deposition of zinc chloride precursor onto glass substrate. Substrate temperature affects surface morphology of films and therefor...ZnO films were prepared at different substrate temperatures through spraying pyrolysis deposition of zinc chloride precursor onto glass substrate. Substrate temperature affects surface morphology of films and therefore their optical and electrical properties. All films are polycrystalline with Wurtzite crystal structure and preferentially grow along c-axis direction. Formation of ZnO rods start at about 500 °C. The diameter and length of rods deposited at 500 °C are350–500 and 550–700 nm, respectively. By increasing substrate temperature, film becomes more coverage and diameter of the rods reduces to 250–300 nm but their length increases to 1,000–1,200 nm, respectively. Optical transmission in visible region decreases with increasing substrate temperature. An ultraviolet emission and two visible emissions at 2.82 and2.37 eV are observed for photoluminescence spectra at room temperature. The resistivity of ZnO films increases with increasing substrate temperature due to surface morphology.展开更多
Zinc oxide(ZnO) thin films were deposited on glass substrates by spray pyrolysis technique decomposition of zinc acetate dihydrate in an ethanol solution with 30 m L of deposition rate, the ZnO thin films were depos...Zinc oxide(ZnO) thin films were deposited on glass substrates by spray pyrolysis technique decomposition of zinc acetate dihydrate in an ethanol solution with 30 m L of deposition rate, the ZnO thin films were deposited at two different temperatures: 300 and 350℃. The substrates were heated using the solar cells method.The substrate was R217102 glass, whose size was 30×17.5×1 mm^3. The films exhibit a hexagonal wurtzite structure with a strong(002) preferred orientation. The higher value of crystallite size is attained for sprayed films at 350℃, which is probably due to an improvement of the crystallinity of the films at this point. The average transmittance of obtain films is about 90%–95%, as measured by a UV–vis analyzer. The band gap energy varies from 3.265 to 3.294 e V for the deposited Zn O thin film at 300 and 350℃, respectively. The electrical resistivity measured of our films are in the order 0.36 Ω·cm.展开更多
基金Funded by the National Natural Science Foundation of China(No.51472206)the National ITER Program of China(2015GB115001)the Program for Innovative Research Team in Shaanxi Province(No.2013KCT-07)
文摘Powder in tube process(PIT) was adopted for the fabrication of single filament Bi-2223 tapes, and a heat treatment process including the first heat treatment(HT1), intermediate rolling(IR), and second heat treatment(HT2) was performed. The phase evolution mechanism and microstructure changes during these heat treatment processes were systematically discussed. The influences of HT1 parameters on the phase evolution process of Bi-2223 tapes were discussed. With the optimized HT1 process, a proper Bi-2223 content of about 90% was achieved. HT2 process was also optimized by adding a post annealing process. An obvious increase of current capacity was obtained due to the enhancement of intergrain connections. Single filament Bi-2223 tapes with the critical current of Ic-90 A were fabricated with the optimized sintering process.
文摘ZnO films were prepared at different substrate temperatures through spraying pyrolysis deposition of zinc chloride precursor onto glass substrate. Substrate temperature affects surface morphology of films and therefore their optical and electrical properties. All films are polycrystalline with Wurtzite crystal structure and preferentially grow along c-axis direction. Formation of ZnO rods start at about 500 °C. The diameter and length of rods deposited at 500 °C are350–500 and 550–700 nm, respectively. By increasing substrate temperature, film becomes more coverage and diameter of the rods reduces to 250–300 nm but their length increases to 1,000–1,200 nm, respectively. Optical transmission in visible region decreases with increasing substrate temperature. An ultraviolet emission and two visible emissions at 2.82 and2.37 eV are observed for photoluminescence spectra at room temperature. The resistivity of ZnO films increases with increasing substrate temperature due to surface morphology.
基金supported in part by the National Project Research (PNR)VTRS laboratory of El–Oued University, X-ray diffraction data in this work were acquired with an instrument supported by the University of Biskra
文摘Zinc oxide(ZnO) thin films were deposited on glass substrates by spray pyrolysis technique decomposition of zinc acetate dihydrate in an ethanol solution with 30 m L of deposition rate, the ZnO thin films were deposited at two different temperatures: 300 and 350℃. The substrates were heated using the solar cells method.The substrate was R217102 glass, whose size was 30×17.5×1 mm^3. The films exhibit a hexagonal wurtzite structure with a strong(002) preferred orientation. The higher value of crystallite size is attained for sprayed films at 350℃, which is probably due to an improvement of the crystallinity of the films at this point. The average transmittance of obtain films is about 90%–95%, as measured by a UV–vis analyzer. The band gap energy varies from 3.265 to 3.294 e V for the deposited Zn O thin film at 300 and 350℃, respectively. The electrical resistivity measured of our films are in the order 0.36 Ω·cm.