Hydrodynamic Characteristics of Square Heaving Plates with Opening Under Forced Oscillation

The existence of the heaving plates can improve the heaving motion performance of an offshore structure significantly by providing both extra added mass and damping.In the current research,numerical investigation is carried out on the hydrodynamic characteristics of both isolated square heaving plate and double square heaving plates with opening by an immersed boundary-lattice Boltzmann method.The effects on hydrodynamic performance of plates due to Keulegan-Carpenter(KC)number,frequency number,opening ratio,opening distribution and spacing of plates are examined.It is found that the heaving plates with optimized opening ratio can provide additional damping compared with the plates without opening.Better hydrodynamic characteristics of double plates can be obtained with the increase of plate spacing.

Hierarchical closed form solutions for plates bent by localized transverse loadings

3D and 2D closed form plate models are here applied to static analysis of simply supported square isotropic plates. 2D theories are hierarchically classified on the basis of the accuracy of the displacements and stresses obtained by comparison to the 3D exact results that could be assumed by the reader as benchmark for further analyses. Attention is mainly paid on localized loading conditions, that is, piecewise constant load. Also bi-sinusoidal and uniformly distributed loadings are taken into account. All of those configurations are considered in order to investigate the behavior of the 2D models in the case of continu- ous/uncontinuous, centric or off-centric loading conditions. The ratio between the side length a and the plate thickness h has been assumed as analysis parameter. Higher order 2D models yield accurate results for any considered load condition in the case of moderately thick plates, a/h=10. In the case of thick plates, a/h=5, and continuous/uncontinuous centric loading conditions high accuracy is also obtained. For the considered off-centric load condition and thick plates good results are provided for some output quantities. A better solution could be achieved by simply increasing the polynomial approximation order of the axiomatic 2D displacement field.

Plate reinforced square hollow section X-joints subjected to in-plane moment

The static test of 13 square hollow section(SHS) X-joints with different β and different types of plate reinforcement under in-plane moment in brace was carried out. Experimental test schemes, failure modes of specimens, moment-vertical displacement curves, moment-deformation of the chord, and strain strength distribution curves were presented. The effect of β and plate reinforcement types on in-plane flexural property of SHS X-joints was studied. Results show that punching shear of chord face disappears, brace material fracture appears and concave and convex deformation of chord decrease when either collar plates or doubler plates were welded on chord face. Moment-vertical displacement curves of all specimens have obvious elastic, elastic-plastic and plastic stages. As β increases, the in-plane flexural ultimate capacity and initial stiffness of joints of the same plate reinforcement type increase, but ductility of joints decreases. With the same β, the in-plane flexural initial stiffness and ultimate capacity of doubler plate reinforced joints, collar plate reinforced joints, and unreinforced joints decrease progressively. Thickness of reinforcement plate has no obvious effect on in-plane flexural initial stiffness and ultimate capacity of joints. As thickness of reinforcement plate increases, the ductility of reinforced X-joints decreases. The concave and convex deformation of every specimen has good symmetry;as β increases, the yield and ultimate deformation of chord decrease.

The deformation and failure mechanism of cylindrical shell and square plate with pre-formed holes under blast loading

The deformation and failure mechanism of cylindrical shells and square plate with pre-formed holes under blast loading were investigated numerically by employing the Ansys 17.0 and Ls-Dyna 971.To calibrate the numerical model,the experiments of square plates with pre-formed circle holes were modeled and the numerical results have a good agreement with the experiment data.The calibrated numerical model was used to study the deformation and failure mechanism of cylindrical shells with pre-formed circle holes subjected to blast loading.The structure response and stress field changing process has been divided into four specific stages and the deformation mechanism has been discussed systematically.The local and global deformation curves,degree of damage,change of stress status and failure modes of cylindrical shell and square plate with pre-formed circular holes are obtained,compared and analyzed,it can be concluded as:(1)The transition of tensile stress fields is due to the geometrical characteristic of pre-formed holes and cylindrical shell with arch configuration;(2)The existence of preformed holes not only lead to the increasing of stress concentration around the holes,but also release the stress concentration during whole response process;(3)There are three and two kinds of failure modes for square plate and cylindrical shell with pre-formed holes,respectively.and the standoff distance has a key influence on the forming location of the crack initiating point and the locus of crack propagation;(4)The square plate with pre-formed holes has a better performance than cylindrical shell on blast-resistant capability at a smaller standoff distance,while the influence of pre-formed holes on the reduction of blast-resistant capability of square plate is bigger than that of cylindrical shell.

CFD Analysis of Spiral Flow Fields in Proton Exchange Membrane Fuel Cells

Proton exchange membrane fuel cells(PEMFCs)are largely used in various applications because of their pollution-free products and high energy conversion efficiency.In order to improve the related design,in the present work a new spiral flow field with a bypass is proposed.The reaction gas enters the flow field in the central path and diffuses in two directions through the flow channel and the bypass.The bypasses are arranged incrementally.The number of bypasses and the cross-section size of the bypasses are varied parametrically while a single-cell model of the PEMFC is used.The influence of the concentration of liquid water and oxygen in the cell on the performance of different flow fields is determined by means of Computational fluid dynamics(COMSOL Multiphysics software).Results show that when the bypass number is 48 and its cross-sectional area is 0.5 mm^(2),the cell exhibits the best performances.

ANALYTIC SENSITIVITY ANALYSIS FORSHAPE OPTIMIZATION

Analytic sensitivity analysis technology for the boundary element method (BEM) is presented, combined with a shape optimization system for structural analysis. A shape optimization was done for an elastomer under planar stress, based on this new algorithm. A multi-object problem was studied as an illustrative example for the programmer, using weighted summing method. The result is feasible.