Seismic performance of recycled concrete-filled square steel tube columns

An experimental study on the seismic performance of recycled concrete-filled square steel tube （RCFST） columns is carried out. Six specimens were designed and tested under constant axial compression and cyclic lateral loading. Two parameters, replacement percentage of recycled coarse aggregate （RCA） and axial compression level, were considered in the test. Based on the experimental data, the hysteretic loops, skeleton curves, ductility, energy dissipation capacity and stiffness degradation of RCFST columns were analyzed. The test results indicate that the failure modes of RCFST columns are the local buckling of the steel tube at the bottom of the columns, and the hysteretic loops are full and their shapes are similar to normal CFST columns. Furthermore, the ductility coefficient of all specimens are close to 3.0, and the equivalent viscous damping coefficient corresponding to the ultimate lateral load ranges from 0.323 to 0.360, which demonstrates that RCFST columns exhibit remarkable seismic performance.

Behavior of High Strength Concrete Filled Square Steel Tube Stub Columns with Inner CFRP Tube Under Biaxial Eccentric Compression

This paper studies the contribution of CFRP(carbon fiber-reinforced polymer)to the mechanical behavior of high strength concrete-filled square steel tube(HCFST)under biaxial eccentric compression.The new type of composite member is composed of an inner CFRP tube and an outer steel tube with concrete filled in the two tubes.The finite element analysis was made by ABAQUS on the behavior of high strength concrete filled square steel tubular columns with inner CFRP circular tube subjected to bi-axial eccentric loading.The results obtained from the finite element analysis were verified with the experimental results.In addition,the load-deflection curves in the whole process were calculated and analyzed,which can be divided into three segments:Elastic phase,plastic phase,descending phase.Based on the load-deflection curves,the stresses analysis on the core concrete,CFRP tube and steel tube were conducted.The confinement effect of the CFRP tube improves the ductility of HCFST-CFRP stub column.CFRP ratio and eccentricity affect the ultimate bearing capacity of HCFST stub column.Finally,a calculation formula of ultimate bearing capacity was proposed in the paper.

Axial Compression Behavior and Analytical Method of L-Shaped Column Composed of Concrete-Filled Square Steel Tubes

Based on the characteristics of an L-shaped column composed of concrete-filled square steel tubes, the axial compression experiment and nonlinear finite element analysis were carried out to study the mechanical property of the L-shaped column. The load-displacement curve for the L-shaped column, the deflection and load-strain curves for the mono columns were obtained by the axial compression experiment. The results show that the L-shaped column exhibits a flexural-torsional buckling failure mode. The numerical simulation by the finite element analysis shows that the bearing capacity and failure mode are in accordance with those of the axial compression experiment and the feasi- bility of the finite element analysis is proved. For the calculation of the bearing capacity of the L-shaped column com- posed of concrete-filled square steel tubes, an analytical method is proposed based on the theory of the elastic stability and spatial truss model. The results of the analytical method are in good agreement with those of the axial compression experiment and the finite element analysis.

Prediction of Axial Capacity of Concrete-Filled Square Steel Tubes Using Neural Networks

The application of artificial neural network to predict the ultimate bearing capacity of CFST （ concrete-filled square steel tubes） short columns under axial loading is explored. Input parameters consiste of concrete compressive strength, yield strength of steel tube, confinement index, sectional dimension and width-to-thickness ratio. The ultimate bearing capacity is the only output parameter. A multilayer feedforward neural network is used to describe the nonlinear relationships between the input and output variables. Fifty-five experimental data of CFST short columns under axial loading are used to train and test the neural network. A comparison between the neural network model and three parameter models shows that the neural network model possesses good accuracy and could be a practical method for predicting the ultimate strength of axially loaded CFST short columns.

Ductility and Ultimate Capacity of Concrete-Filled Lattice Rectangular Steel Tube Columns

A kind of concrete-filled lattice rectangular steel tube(CFLRST)column was put forward.The numerical simulation was modeled to analyze the mechanical characteristic of CFLRST column.By comparing the load-deformation curves from the test results,the rationality and reliability of the finite element model has been confirmed,moreover,the change of the section stiffness and stress in the forcing process and the ultimate bearing capacity of the column were analyzed.Based on the model,the comparison of ultimate bearing capacity and ductility between CFLRST column and reinforced concrete(RC)column were also analyzed.The results of the finite element analysis show that the loading process of CFLRST column consists of elastic stage,yield stage and failure stage.The failure modes are mainly strength failure and failure of elastoplastic instability.CFLRST column has higher bearing capacities in comparison with reinforced concrete columns with the same steel ratio.In addition,the stiffness degeneration of CFLRST column is slower than RC column and CFLRST column has good ductility.

Joint member angle limits of composite beams and CFT square columns

This work aims to understand the relationship between the member angle limit and the energy ratio for 24 test samples of composite beams and CFT square steel tube columns. This work also compares the formula applicability for member angle limit with the previous test result to provide the basic data for the design of composite beam-CFT column. The evaluation of the member angle limit was performed with concrete compressive strength (fC =22.16 MPa, 30.49 MPa), breadth-to-thickness ratio (B/t=25.0, 33.3, 43.5), and axial capacity ratio (N/N0=0, 0.3, 0.4, 0.5) as the main variables of the test samples. For the relationship between the member angle limit (Ru) and the energy ratio (ES/EC ), the test result shows that the energy ratio becomes lower as the axial capacity ratio and the breadth-to-thickness ratio increase. The energy ratio is lower for the Type B test sample compared with that of Types A and C. For the formula suggested by SATO, the test samples are distributed evenly for comparison between test values and the member angle limit; however, other formulas indicate a deviation. Specifically, for the comparison between R u,cal and R u (Test), Maeda's formula shows severe deviation.

局部环向变厚度方钢管混凝土柱偏压力学性能研究

针对海洋环境中飞溅区造成的钢管混凝土柱局部环向腐蚀现象,采用机械削减方式模拟钢管壁厚局部环向腐蚀,进行了7个方钢管混凝土柱偏压试验,揭示了削弱率和偏心率对其偏压承载力的影响,并通过数值模拟对削弱率进行拓展分析.提出了基于削弱率的偏压承载力降低系数,代入中、美规范进行偏压承载力计算.结果表明:钢管的局部环向变厚度严重削弱了方钢管混凝土柱的偏压承载力和侧向挠曲能力;较大的加载偏心率也降低了其偏压承载力,但增大了其侧向挠曲能力.引入偏压承载力降低系数后,根据中、美规范计算得到的偏压承载力与试验值均吻合较好;相比于我国规范,美国规范在计算偏压承载力时相对更加保守.

配筋空心方钢管高强混凝土纯弯构件受力性能有限元分析

目的 研究配筋空心钢管高强混凝土构件的抗弯性能,推动其在建筑结构中的应用。方法 采用有限元分析软件ABAQUS建立配筋空心钢管混凝土构件有限元模型,在验证模型准确的基础上,分析构件的受力全过程及钢材屈服强度、混凝土抗压强度、钢管壁厚、钢筋直径、普通钢筋数量对构件受弯性能的影响。结果 纯弯试件在荷载作用下受力过程可分为3个阶段:弹性阶段、弹塑性阶段和强化阶段;试件破坏形态均为受弯破坏,表现出较好地延性。结论 组合构件在弯矩作用下可以很好地协同工作;钢材屈服强度和钢管壁厚的增加对构件承载力的提高影响最显著,建议配置普通钢筋数量在6~8根为最优。

MS1180方管连续辊弯成形角部开裂机理

方矩形管在辊弯成形中会产生角部开裂现象,这已成为严重制约方矩形管质量的关键问题,为解决其角部开裂缺陷展开深入研究,寻找控制开裂缺陷的方法。首先通过对MS1180进行单轴拉伸、缺口拉伸和平面应变实验得到了材料的力学特性,并分别利用3种拉伸试验将Ayada、Rice-Tracey和标准化Cockroft-Latham准则进行校准,得到了预测误差最小的一种断裂准则,并以此构建了方矩管辊弯开裂模型。其次利用辊弯成形COPRA RF设计软件和有限元MARC仿真专业软件,结合生产实际条件建立了方矩形管连续辊弯成形三维有限元模型,并进行辊弯实验验证模型的准确性。最后采用扫描电镜和金相显微镜对方矩形管开裂件以及断口进行微观观察,针对性的利用有限元模型探究了方矩形管连续辊弯成形时应力-应变分布规律,并分析了道次数量、角部成形半径和机架间距对方矩管角部应力-应变分布的影响。结果表明:发现材料起裂点位于角部近外层,对开裂断口进行分析,得到其开裂方式为准解理开裂,角部剪切面上所受的主应力过大导致其开裂;增加辊弯道次数量、方矩形管角部成形半径以及机架之间的间距能有效减少开裂问题的出现,为以后解决方矩形管角部开裂问题提供了理论基础。

多腔钢-混凝土组合壁式柱弱轴方向抗震性能试验研究

用于异形柱框架结构的各种截面型式的多腔钢-混凝土组合柱具有良好的使用功能和可装配建造性能,与异形柱面外有侧肢不同,保证矩形截面壁式柱弱轴方向的抗震性能更为重要。为了探究多腔钢-混凝土组合壁式柱弱轴方向的抗震性能与受力机制,运用低周往复荷载试验与有限元分析相结合的方法开展研究。结果表明:压弯荷载作用下,多腔钢-混凝土组合壁式柱弱轴方向的滞回曲线饱满,其全过程受力可划分为稳定承载、转化过渡和峰后二阶效应显现三个阶段,试件对应的两个特征分界点的层间位移角分别为1/57和1/27;试件屈服点和失效破坏点对应的层间位移角分别为1/85和1/23,均大于规范限值,延性系数为3.73;两端钢管、中间钢板和腔内混凝土可协同受力,混凝土未见明显压碎和开裂,钢管和钢板未见明显损伤;所得有限元模拟结果与试验结果吻合度高,骨架曲线平均相对误差为4.6%。上述成果深化了对多腔钢-混凝土组合壁式柱弱轴方向抗震性能的认知,为工程应用提供了参考。

矩形钢管混凝土束风机塔筒风振特性研究

随着风电资源优势区开发逐渐饱和,风电开发的重心开始向风资源条件相对恶劣的低风速地区转移,分布式、大功率、高塔筒和长叶片已经成为风电行业发展趋势。基于此提出了一种新型的矩形钢管混凝土束风机塔筒,该塔筒由矩形钢管混凝土束拼接而成,具有强度高、刚度大和耗能能力强的优点。为研究该塔筒结构的风振响应特性,选用Kaimal脉动风速功率谱,采用谐波合成法模拟风荷载时程曲线,对其进行了动力时程分析,并计算了风振系数及等效静力风荷载。结果表明:该新型塔筒在额定风速下位移塔顶位移最大值为911.84 mm,对应的水平位移角为1/154,符合规范要求。塔筒各构件的强度较好,且具有较大的安全富余度。基于位移等效的阵风荷载因子法计算得到的风振系数值较低;在惯性风荷载法计算得到的等效静力风荷载作用下,结构位移、基底剪力与结构随机振动分析得到的基本一致。

热-湿-力耦合作用对高温后方钢管混凝土短柱轴压力学性能影响试验研究

火灾发生时钢管混凝土内部会产生水蒸气,为探讨热-湿-力耦合作用对高温后方钢管混凝土轴压力学性能的影响,进行了10根高温后方形钢管混凝土短柱轴压力学性能试验,研究排气孔数量、布置位置、轴压比和升温时间等参数对其破坏形态、轴压刚度与剩余承载力等力学性能的影响。试验结果表明,试件破坏形态表现为压溃破坏;在其他参数相同的情况下,与升温前相比,随着排气孔数量从2个增加至4个和6个,轴压刚度分别降低了69.1%、73.3%、76.4%,剩余承载力分别降低了15.8%、16.2%、21.7%。轴压刚度随轴压比的增大而降低;随着升温时间的延长,剩余承载力先随轴压比的增大而增大,后随轴压比的增大而减小。研究结果可为钢管混凝土柱的抗火设计和该类结构火灾后的损伤评估与加固提供参考。

方钢管螺旋筋约束自密实高强混凝土柱抗震性能试验研究

为研究方钢管螺旋筋约束自密实高强混凝土柱的抗震性能,以轴压比、剪跨比、有无配制螺旋筋以及螺旋筋间距作为设计参数,进行了7个试件的低周反复加载试验,获取了各试件的滞回曲线以及应变分布。试验结果表明:试件破坏特征主要为方钢管柱脚区域出现明显鼓曲形成塑性铰区域;随轴压比的提高,试件抗剪承载力、环线刚度和耗能能力均有提升,剪跨比对试件抗震性能的影响规律不明显。配制螺旋筋对峰值承载力和刚度的影响较小,而对试件延性及耗能的提升明显,与无配筋试件相比试件延性平均提升了15.4%,耗能平均提升了114.9%。螺旋筋间距越密对试件抗震性能提升效果更优;适当增大轴压比,控制剪跨比在5以内以及增设螺旋筋对提升其承载能力和变形能力有积极作用。

内置异形箍筋矩形钢管混凝土柱的轴压力学性能

钢管混凝土作为一种发展前景广阔的结构形式,具有较好的承载力和塑性变形能力。矩形钢管混凝土柱作为其中常见的一种形式,在实际工程中的应用较为广泛。该研究基于矩形钢管混凝土在实际应用中存在的长短边约束不一致和对核心混凝土约束不足两个问题,探究一种新型的矩形钢管混凝土构件,即内置异形箍筋矩形钢管混凝土柱。为此,对11根内置异形箍筋矩形钢管混凝土柱、2根内置跑道形箍筋的矩形钢管混凝土柱、2根普通矩形钢管混凝土柱开展了轴压力学性能试验,重点分析了并束距、钢管壁厚、混凝土强度等级、箍筋间距、箍筋直径、内置用钢量等重要参数对内置异形箍筋矩形钢管混凝土柱的轴压承载力和延性的影响规律。结果表明:在总用钢量不变的情况下,将矩形钢管的壁厚减薄,并加工成异形箍筋内置于核心混凝土中,能够有效地提高试件的轴压承载力和延性;内置异形箍筋矩形钢管混凝土柱的轴压过程可以分为4个阶段——弹性阶段、弹塑性阶段、塑性强化段、下降段;相比于普通矩形钢管混凝土柱,内置异形箍筋矩形钢管混凝土柱有更为饱满的塑性强化段。在试验和参数分析结果的基础上,采用已有的约束混凝土本构模型,推导得到内置异形箍筋矩形钢管混凝土柱的轴压承载力计算公式。该研究可为实际工程应用提供科学依据和数据参考。

装配式方钢管约束混凝土桥墩恢复力模型研究

采用ABAQUS通用有限元软件对装配式方钢管约束混凝土桥墩进行建模,计算了桥墩试件荷载-位移滞回曲线与骨架曲线特征值;以轴压比、长细比、约束系数、方钢管屈服强度、混凝土强度、钢管嵌入深度与桥墩边长比、嵌套钢管直径与桥墩边长比、嵌套钢管厚度与桥墩边长比为拓展参数,研究各参数对装配式方钢管约束混凝土桥墩荷载-位移骨架曲线的影响规律;借鉴钢管约束钢筋混凝土柱的计算框架,拟合得出装配式方钢管约束混凝土桥墩各特征值(弹性刚度、水平荷载峰值、峰值荷载位移与下降段刚度)的计算公式;该计算公式与有限元分析结果吻合良好,有限元分析值与公式计算值之比的平均值为1.004~1.035,均方差为0.133~0.162;选取实际工程对算法进行实例验证,计算结果与有限元数值吻合良好。

方钢管煤矸石混凝土短柱轴压承载力有限元分析

目的 研究各设计参数在不同煤矸石粗骨料取代率下对方钢管煤矸石混凝土短柱轴压承载力的影响规律,提出轴压承载力计算式。方法 利用ABAQUS有限元分析软件建立方钢管煤矸石混凝土短柱轴压有限元模型,并与试验结果对比,验证模型的准确性;分析试件应力分布与荷载分配,并采用控制变量法分析试件在5种煤矸石粗骨料取代率下主要参数对其轴压承载力的影响。结果 相同设计参数下,试件轴压承载力随煤矸石粗骨料取代率的提高而降低,且最大降幅未超过14%;当试件截面边长一定时,含钢率对试件轴压承载力的影响最显著,其中,含钢率由7.4%增加至20.3%使试件轴压承载力在不同取代率下平均提升68.85%。结论 掺入煤矸石粗骨料不会使构件轴压承载力显著劣化,依据《钢管混凝土结构技术规范》(GB 50936—2014),引入煤矸石粗骨料取代率影响系数后的计算误差小于5%,可为相关研究提供参考。

应用于方矩管生产的扁方吹杆压管机的设计研究

为了解决方矩管在实际生产过程中出现顶吹杆生产效率低、安全系数低的问题,基于生产实际设计了一款扁方吹杆压管机,设计的扁方吹杆压管机由底座、安装板、压管机构等组成,通过对设计的设备进行应用研究,发现扁方吹杆压管机能够有效解决方矩管在生产过程中的吹杆问题,同时提升了方矩管的生产效率,减少了设备的磨损损耗。

矩形钢管在输电铁塔中的应用研究

近年来,圆形钢管构件由于其全对称、体型系数小的截面特性,在特高压输电铁塔或者大跨越塔中得到了大规模的应用,但是圆截面在微风中容易引起涡激振动,微风振动在已投运线路中时有发生,个别还造成了构件的破坏。矩形构件斯托罗哈数较小,可有效改善构件的气动性能,提高构件的起振临界风速,本文通过对矩形构件的宽厚比,起振临界风速、驰振风速等方面进行计算分析,结果表明:矩形构件在不增加工程量的情况下,可大幅提高起振临界风速,可在结构的辅助构件或者隔面中应用。

广州白云国际会议中心国际会堂结构设计和施工重难点

采用YJK和ETABS对广州白云国际会议中心国际会堂结构进行弹性分析,采用Perform-3D进行罕遇地震作用下的整体结构弹塑性动力分析,并通过采取针对性的加强措施,改善了结构受力,提高了结构抗震性能,达到了预设的抗震性能目标。对大跨度钢结构构件进行方案选型,提出了大跨度钢结构桁架局部构件后装施工控制法和大悬挑钢结构桁架构件局部弯矩释放法,可以有效地减小结构构件局部受力,更加经济合理。对主会场大跨度楼盖进行竖向舒适度分析,结果表明竖向振动加速度满足规范要求,人群激励模式起控制性作用。通过采用合理的结构方案,以及与建筑专业的密切配合,很好地实现了建筑功能及建筑造型,以及项目快速建造的要求。

扁钢48×55的工艺设计与实践应用

扁钢作为一种常用的钢铁材料,因其具有较高的灵活性和适应性,故被广泛用于建筑、制造业等领域,随着新材料和新技术的出现,扁钢也在不同的领域中得到创新和应用。我公司三轧分厂对现用圆钢轧制料型进行分析,发现φ45规格和该料型接近,重新设计后4道孔型,采用平立交替箱方孔型,合理配置每道次的压下量,一次试轧成功,并具备批量生产条件,满足了客户需求。