Physical model simulation of rock-support interaction for the tunnel in squeezing ground

The existence of squeezing ground conditions can lead to significant challenges in designing an adequate support system for tunnels.Numerous empirical,observational and analytical methods have been suggested over the years to design support systems in squeezing ground conditions,but all of them have some limitations.In this study,a novel experimental setup having physical model for simulating the tunnel boring machine(TBM)excavation and support installation process in squeezing clay-rich rocks is developed.The observations are made to understand better the interaction between the support and the squeezing ground.The physical model included a large true-triaxial cell,a miniature TBM,laboratoryprepared synthetic test specimen with properties similar to natural mudstone,and an instrumented cylindrical aluminum support system.Experiments were conducted at realistic in situ stress levels to study the time-dependent three-dimensional tunnel support convergence.The tunnel was excavated using the miniature TBM in the cubical rock specimen loaded in the true-triaxial cell,after which the support was installed.The confining stress was then increased in stages to values greater than the rock’s unconfined compressive strength.A model for the time-dependent longitudinal displacement profile(LDP)for the supported tunnel was proposed using the tunnel convergence measurements at different times and stress levels.The LDP formulation was then compared with the unsupported model to calculate the squeezing amount carried by the support.The increase in thrust in the support was backcalculated from an analytical solution with the assumption of linear elastic support.Based on the test results and case studies,a recommendation to optimize the support requirement for tunnels in squeezing ground is proposed.

Examining the effect of adverse geological conditions on jamming of a single shielded TBM in Uluabat tunnel using numerical modeling

Severe shield jamming events have been reported during excavation of Uluabat tunnel through adverse geological conditions, which resulted in several stoppages at advancing a single shielded tunnel boring machine(TBM). To study the jamming mechanism, three-dimensional(3D) simulation of the machine and surrounding ground was implemented using the finite difference code FLAC3D. Numerical analyses were performed for three sections along the tunnel with a higher risk for entrapment due to the combination of overburden and geological conditions. The computational results including longitudinal displacement contours and ground pressure profiles around the shield allow a better understanding of ground behavior within the excavation. Furthermore, they allow realistically assessing the impact of adverse geological conditions on shield jamming. The calculated thrust forces, which are required to move the machine forward, are in good agreement with field observations and measurements. It also proves that the numerical analysis can effectively be used for evaluating the effect of adverse geological environment on TBM entrapments and can be applied to prediction of loads on the shield and preestimating of the required thrust force during excavation through adverse ground conditions.

Analytical computation of support characteristic curve for circumferential yielding lining in tunnel design

Circumferential yielding lining is able to tolerate controlled displacements without failure,which has been proven to be an effective solution to large deformation problem in squeezing tunnels.However,up to now,there has not been a well-established design method for it.This paper aims to present a detailed analytical computation of support characteristic curve(SCC)for circumferential yielding lining,which is a significant aspect of the implementation of convergence-confinement method(CCM)in tunnel support design.Circumferential yielding lining consists of segmental shotcrete linings and highly deformable elements,and its superior performance mainly depends on the mechanical characteristic of highly deformable element.The deformation behavior of highly deformable element is firstly investigated.Its whole deforming process can be divided into three stages including elastic,yielding and compaction stages.Especially in the compaction stage of highly deformable element,a nonlinear stress-strain relationship can be observed.For mathematical convenience,the stress-strain curve in this period is processed as several linear sub-curves.Then,the reasons for closure of circumferential yielding lining in different stages are explained,and the corresponding accurate equations required for constructing the SCC are provided.Furthermore,this paper carries out two case studies illustrating the application of all equations needed to construct the SCC for circumferential yielding lining,where the reliability and feasibility of theoretical derivation are also well verified.Finally,this paper discusses the sensitivity of sub-division in element compaction stage and the influence of element length on SCC.The outcome of this paper could be used in the design of proper circumferential yielding lining.

Tunnelling through weak and fragile rocks of Himalayas

A considerable amount of tunnelling has been going on in India for various projects such as hydroelectric power, irrigation, roads and railways. Most of these projects are located in Himalayas, far away from the urban areas. Tunnelling through weak and jointed rock masses such as the one in the Himalayas is a challenging task for the planners, designers, engineers and geologists because of high overburden, thickly vegetated surface, weak, poor and fragile rocks and highly varying geology with the presence of numerous small and big shear zones, faults, etc. Due to these reasons, various tunnelling problems have been faced in the past and are still being encountered. Failures and the problems may be regarded as challenges and opportunities for generating new knowledge base and thereby increasing self-reliance in tunnelling. The experiences of Himalayan tunnelling through weak and fragile rocks covering varying and mixed geology, understanding on tunnelling in squeezing ground conditions and applicability of TBM in Himalayas are presented. It has also been highlighted that the probe holes planning, drilling and monitoring shall be followed seriously to reduce the geological surprises.

Tunnels in squeezing clay-rich rocks

Squeezing ground conditions,which can lead to severe loads in tunnels,have historically been associated with the presence of clay minerals in the ground.Over the years,many methodologies have been proposed to predict squeezing in tunnels based on tunnel depth,in situ stress,ground mineralogy,and ground strength and deformation behavior.This paper presents a comprehensive review of methodologies to predict tunnel squeezing in clay-rich rocks.A new methodology is proposed where ground conditions and squeezing potential are assessed based on the Stress History and Normalized Soil Engineering Properties(SHANSEP)approach adapted to clayrich rocks,Peck’s stability number and Hoek&Brown’s(1997)Geological Strength Index(GSI).A squeezing number S is suggested to classify ground conditions based on the level of squeezing that the ground may experience in response to tunneling.Finally,it is demonstrated that by combining the proposed classification system and an existing classification system for ground squeezing condition,an accurate estimate of tunnel strain can also be obtained.The proposed method is applied to four case studies of tunnels in squeezing ground in shale and mudstone.