Effects of iron oxide on crystallization behavior and spatial distribution of spinel in stainless steel slag

Chromium plays a vital role in stainless steel due to its ability to improve the corrosion resistance of the latter.However,the re-lease of chromium from stainless steel slag(SSS)during SSS stockpiling causes detrimental environmental issues.To prevent chromium pollution,the effects of iron oxide on crystallization behavior and spatial distribution of spinel were investigated in this work.The results revealed that FeO was more conducive to the growth of spinels compared with Fe2O3 and Fe3O4.Spinels were found to be mainly distrib-uted at the top and bottom of slag.The amount of spinel phase at the bottom decreased with the increasing FeO content,while that at the top increased.The average particle size of spinel in the slag with 18wt%FeO content was 12.8μm.Meanwhile,no notable structural changes were observed with a further increase in FeO content.In other words,the spatial distribution of spinel changed when the content of iron oxide varied in the range of 8wt%to 18wt%.Finally,less spinel was found at the bottom of slag with a FeO content of 23wt%.

Microstructural evolution and mechanical properties of friction stir-welded C71000 copper–nickel alloy and 304 austenitic stainless steel

Dissimilar joints comprised of copper–nickel and steel alloys are a challenge for manufacturers in modern industries, as these metals are not thermomechanically or chemically well matched. The present study investigated the effects of tool rotational speed and linear speed on the microstructure and mechanical properties of friction stir-welded C71000 copper–nickel and 340 stainless steel alloys using a tungsten carbide tool with a cylindrical pin. The results indicated that a rotational-to-linear speed ratio of 12.5 r/mm did not cause any macro defects, whereas some tunneling defects and longitudinal cracks were found at other ratios that were lower and higher. Furthermore, chromium carbide was formed on the grain boundaries of the 304 stainless steel near the shoulder zone and inside the joint zone, directing carbon and chromium penetration toward the grain boundaries. Tensile strength and elongation percentages were 84% and 65% of the corresponding values in the copper–nickel base metal, respectively.

Laser Shock Processing of an Austenitic Stainless Steel and a Nickel-base Superalloy

An austenitic stainless steel 1Cr18Ni9Ti and a solid solution-strengthened Ni-base superalloy GH30 were shock processed using a Q-switched pulsed Nd-glass laser. Microstructure, hardness and residual stress of the laser shock processed surface were investigated as functions of laser processing parameters. Results show that high density of dislocations and fine deformation twins are produced in the laser shock processed surface layers in both the austenitic stainless steel and the nickel-base superalloy. Extensive strain-induced martensite was also observed in the laser shock processed zone of the austenitic steel. The hardness of the laser shock processed surface was significantly enhanced and compressive stress as high as 400 MPa was produced in the laser shock processed surface.

CYCLIC OXIDATION OF Ni-La_2O_3 COMPOSITE COATINGS ELECTRODEPOSITED ON NICKEL AND Fe26Cr STAINLESS STEEL

ＣＹＣＬＩＣＯＸＩＤＡＴＩＯＮＯＦＮｉＬａ２Ｏ３ＣＯＭＰＯＳＩＴＥＣＯＡＴＩＮＧＳＥＬＥＣＴＲＯＤＥＰＯＳＩＴＥＤＯＮＮＩＣＫＥＬＡＮＤＦｅ２６ＣｒＳＴＡＩＮＬＥＳＳＳＴＥＥＬ①ＰｅｎｇＸｉａｏ１，２，ＬｉＴｉｅｆａｎ１，２，ＷｕＷｅｉｔａｏ１Ｓｔ...

Strain rate and cold rolling dependence of tensile strength and ductility in high nitrogen nickel-free austenitic stainless steel

The tensile strength and ductility of a high nitrogen nickel-free austenitic stainless steel with solution and cold rolling treatment were investigated by performing tensile tests at different strain rates and at room temperature. The tensile tests demonstrated that this steel exhibits a significant strain rate and cold rolling dependence of the tensile strength and ductility.With the increase of the strain rate from 10^-4s^-1to 1 s^-1, the yield strength and ultimate tensile strength increase and the uniform elongation and total elongation decrease. The analysis of the double logarithmic stress–strain curves showed that this steel exhibits a two-stage strain hardening behavior, which can be well examined and analyzed by using the Ludwigson equation. The strain hardening exponents at low and high strain regions（n2and n1） and the transition strain（εL） decrease with increasing strain rate and the increase of cold rolling RA. Based on the analysis results of the stress–strain curves, the transmission electron microscopy characterization of the microstructure and the scanning electron microscopy observation of the deformation surfaces, the significant strain rate and cold rolling dependence of the strength and ductility of this steel were discussed and connected with the variation in the work hardening and dislocation activity with strain rate and cold rolling.

Microstructure and mechanical characterization of Incoloy 825 Ni-based alloy welded to 2507 super duplex stainless steel through dissimilar friction stir welding

The feasibility of dissimilar friction stir welding(FSW)between the SAF 2507 super duplex stainless steel and the Incoloy825 Ni-based superalloy was evaluated.The microstructure and mechanical behavior of the weldments were examined too.The results showed that the alloys were successfully welded together by positioning the SAF 2507 on the advancing side.The nuggets displayed higher hardness than the base metals,due to the occurrence of dynamic recrystallization and the subsequent refinement of the microstructures.The welded sample obtained the similar strength to the Incoloy 825 parent metal,showing the ductile fracture mode after the tensile tests by SEM.Moreover,the weld zone(31 J)exhibited higher and lower toughness than the Incoloy 825(23 J)and SAF 2507(42 J)parent metals,respectively.Based on the obtained results,the FSW method could be recommended to weld the super duplex stainless steel/Ni-based superalloy joints.

Effect of the heat input on microstructure and properties of submerged arc welded joint of 08Cr19MnNi3Cu2N stainless steel

SAW308L submerged arc welding wire and SJ601A submerged arc welding flux were selected to weld the 12 mm 08Cr19MnNi3Cu2N low nickel and high nitrogen austenitic stainless steel plates with three different welding heat input,and microstructure,tensile properties,microhardness and corrosion properties of the welded joints were studied.The results show that no defects are found in the three groups of welded joints,and the welded joints have better performance.The tensile strength of 08Cr19MnNi3Cu2N stainless steel welded joints with different heat input is slightly lower than that of the base metal,and fracture occurs in the weld zone,and the hardness of the weld zone is lower than that of the base metal.The weld microstructure of stainless steel welded joints with different heat input is composed of austenite+δferrite,and ferrite is uniformly distributed in austenite.With the increase of the welding heat input,the ferrite content in the weld zone decrease gradually,the grain size in the thermal affected zone increase gradually,and the impact toughness reduce.

Nickel-free Stainless Steel for Medical Applications

BIOSS4 steel is essentially a nickel-free austenitic stainless steel developed by the Institute of Metal Research, Chinese Academy of Sciences, in response to nickel allergy problems associated with nickel-containing stainless steels that are widely used in medical applications. The high nitrogen content of this steel effectively maintains the austenitic stability and also contributes to the high levels of corrosion resistance and strength. BIOSS4 steel possesses a good combination of high strength and toughness, better corrosion resistance, and better blood compatibility, in comparison with the medical 316L stainless steel. Potential applications of BIOSS4 steel can include medical implantation material and orthodontic or orthopedic devices, as well as jewelries and other decorations.

Relationship between the Corrosion and Cr-Ni Content of Stainless Steel in Borax Bath

The corrosion of stainless steel was experimentally investigated and analyzed to improve the service-life of the crucible and fixture clamps. Through the experiment, stainless steel was found to satisfy the crucible and fixture clamps materials. As the chromium element mass percentage of the stainless steel increased, the corrosion decreased rapidly at first and then slowly increased. With the corrosion time prolonging, the corrosion growth rate is generally a downward trend. With Chromium 20%, the corrosive were the least. With Nickel element mass percentage increased, the corrosion increased rapidly at first and then decreased rapidly, flatten at the last. It was special that the corrosion had little relationship with the Chromium and Nickel mass percentage when the Nickel percentage is more than 35%. The most remarkable corrosion is corresponding with the Nickel element 12%, the least corrosion with Nickel element 80%. So Nickel element 35% is the most optional.

Reduction of chromium oxides in stainless steel dust

The recovery of metal oxides from stainless steel dust using C（graphite）, SiFe, and Al as reductants was investigated under various conditions. The apparent distribution ratio of Cr（L Cr ′^m/s ） in the recovered metal and residual slag phases was defined as the major performance metric. The results show that the recovery ratio of metals increases as the ratio of CaO ：SiO2 by mass in the residual slag increases to 1.17. The residual content of metals in the slag decreases as the Al2O3 content of the slag is increased from approximately 8wt% to 10wt%. The recovery ratio of Cr increases with increasing L Cr ′^ m/s , and a linear relationship between L Cr ′^m/s and the activity coefficient ratio of CrO in the slag and the recovered metal phase is observed. The combination of C and SiFe or Al as the reducing agents reveals that Si is the more effective coreductant.

Growth and aggregation control of spinel by shear-force-based melting modification of stainless steel slag

To improve the efficiency of melting modification for stainless steel(SS) slag, a shear force was introduced in this work and its effects on the spinel and silicate melt were experimentally investigated. The results indicated that the use of shear force changed the nucleation and growth behaviors of spinel and that the effects of shear force varied with its intensity. The aggregation behavior of spinel under different shear-force conditions was studied, revealing that large spinel clusters could be formed when the stirring speed was controlled. However, no notable change in the melt structure of the silicate was detected in this study. The optimal stirring speed for the melting modification treatment was 50 r·min^(-1), which substantially promoted spinel growth and aggregation, resulting in modified SS slag with excellent chromium sequestration capability.

Researches on the problems in the production of low nickel austenitic stainless steel

Problems encountered in the production of low nickel austenitic stainless steel have been studied. These problems primarily include the changes to the microstructure of the slab during the heating process, the formation and removal of deformation - induced martensite during cold rolling, and the effects of the annealing process on the surface oxide structure. A reasonable manufacturing process has been proposed on the basis of the research results and high-quality cold-rolled strips of low nickel austenitic stainless steel have been produced.

Effect of FeO on the formation of spinel phases and chromium distribution in the CaO-SiO_2-MgO-Al_2O_3-Cr_2O_3 system

Synthetic slag samples of the CaO-SiO2-MgO-A1203-Cr203 system were obtained to clarify the effect of FeO on the formation of spinel phases and Cr distribution. X-ray diffraction （XRD） and scanning electron microscopy （SEM） equipped with energy-dispersive spectroscopy （EDS）, as well as the thermodynamic software FactSage 6.2, were used for sample characterization. The results show that the addition of FeO can decrease the viscosity of molten slag and the precipitation temperatures of melilite and merwinite. The solidus temperature significantly decreases from 1400 to 1250℃ with the increase of FeO content from 0wt% to 6wt%. The addition of FeO could enhance the content of Cr in spinel phases and reduce the content of Cr in soluble minerals, such as merwinite, melilite, and dicalcium silicate. Hence, the addition of FeO is conducive to decreasing Cr leaching.

Intergranular corrosion behavior of high nitrogen austenitic stainless steel

The intergranular corrosion （IGC） behavior of high nitrogen austenitic stainless steel （HNSS） sensitization treated at 650-950℃ was investigated by the double loop electrochemical potentiodynamic reactivation （DL-EPR） method. The effects of the electrolytes, scan rate, sensitizing temperature on the susceptibility to IGC of HNSS were examined. The results show that the addi-tion of NaCl is an effective way to improve the formation of the cracking of a passive film in chromium-depleted zones during the reactivation scan. Decreasing the scan rate exhibits an obvious effect on the breakdown of the passive film. A solution with 2 mol/L H2SO4＋1 mol/L NaCl＋0.01 mol/L KSCN is suitable to check the susceptibility to IGC of HNSS at a sensitizing temperature of 650-950℃ at a suitable scan rate of 1.667 mV/s. Chromium depletion of HNSS is attributed to the precipitation of Cr2N which results in the susceptibility to IGC. The synergistic effect of Mo and N is suggested to play an important role in stabilizing the passive film to prevent the attack of IGC.

Development of ferritic stainless steel B445R with superior corrosion resistance for architectural applications

The dull-finish ferritic stainless steel （FSS） sheet B445R for architectural roofing has been developed by Baosteel. This steel product exhibits excellent corrosion resistance superior to that of SUS 316L with a lower cost. It can be easily formed into roofing panels by ordinary processes. Moreover,the thermal strain of it is less than SUS 316L because of its lower thermal expansion coefficient, and its reflectivity is lower due to the dull-finish treatment. All of these features make it capable of being used as architectural roofing materials in coastal regions.

High corrosion resistance 21%Cr-0.4%Cu ferritic stainless steel contributing to resource conservation

With prices for metal resources such as nickel and molybdenum soaring,there is a heightened sense of crisis concerning resource scarcity.While Type304,the most common stainless steel,offers excellent corrosion resistance,its price is affected significantly by the cost of nickel because of its 8%nickel content.The stainless steel that has the same corrosion resistance as that of Type304 and does not contain nickel and molybdenum has been required.JFE Steel Corporation has developed a new 21%Cr-0.4%Cu stainless steel,the world's first ferritic stainless steel,which offers equivalent corrosion resistance to Type304 while containing absolutely no nickel or molybdenum,two rare metals.The newly developed steel contains 21%chromium with the addition of 0.4% copper.The development of the steel is based on a new discovery that the passive films of stainless steels could be strengthened by the synergy effect of high chromium content and copper addition.Copper addition enriches the chromium content in passive films after field exposure.Newly developed 21%Cr-0.4%Cu stainless steel is adopted for many applications as a substitution for Type304,including commercial kitchenware,building materials and industrial machinery.The steel is expected to be a new standard of a ferritic stainless steel as a substitution for Type304.

Recovery rates of iron, nickel, and chromium via iron-bath reduction of stainless steel dust briquettes based on corundum crucible erosion balance analysis

The leaching of chromium from stainless steel dust （SSD） is deleterious to the environment. To address this issue, the reduction of SSD briquettes can be employed to effectively extract chromium. The recovery rates of iron, chromium, and nickel via ironbath reduction of SSD briquettes were determined using X-ray fluorescence spectroscopy, X-ray diffraction, and scanning electron microscopy measurements. First, the effects of basicity and contents of silicon, iron, CaF2, and carbon on the recovery rates of the three metals were analyzed using the slag amount prediction model, which was originally established from the A1203 balance of corundum crucible erosion behavior. Second, the effect of feeding mode, i.e., whether steel scrap and SSD briquettes were simultaneously added, on the recovery rates was discussed in detail. Third, the iron-bath reduction of SSD briquettes was thermodynamically analyzed. The results indicated that the recovery rates of the three metals are greater than 95% those of using a basicity of 1.5 and 6.0% CaF2, 15% carbon, and 7% ferrosilicon. The recovery rate of chromium increases twofold with the addition of ferrosilicon. The feeding mode of adding briquettes and steel scrap simultaneously is better for recovery of metals and separation of the metal and slag than the feeding mode of adding steel scrap firstly and then briquettes.

Effect of Al2O3 modification on enrichment and stabilization of chromium in stainless steel slag

Spinel phase is considered to be the optimal phase for stabilization of chromium in stainless steel slag.In order to restrain chromium leaching from slag for the effective environmental protection,Al2O3 was utilized for the modification treatment,and the effects on the enrichment and stabilization of chromium were investigated. The mineral phases and the existence state of chromium in slag with various Al2O3 contents at different basicities（ w（CaO）/w（SiO2） were analyzed by scanning electron microscopy-energy dispersive spectroscopy（ SEM-EDS） and X-ray diffraction（ XRD）. The results showed that chromium mainly existed in the glass and spinel phases at basicity of 1. 0 and 1. 5. As the slag basicity increased to 2. 0,chromium was also found in periclase phase. Al2O3 in the stainless steel slag reacted with MgO and Cr2O3,which could generate the Al-rich Mg（CrxAl（1- x））2O4 solid solution. Moreover,the addition of Al2O3 was favorable to reduce the solubility of chromium oxide in liquid phase and suppress the precipitation of periclase phase. The experimental results demonstrated that Al2O3 modification has a positive influence on the enrichment and the stabilization of chromium in the stainless steel slag.

Metallurgical characteristics of armour steel welded joints used for combat vehicle construction

Austenitic stainless steel(ASS) and High nickel steel(HNS) welding consumables are being used for welding Q&T steels, as they have higher solubility for hydrogen in austenitic phase, to avoid hydrogen induced cracking(HIC) but they are very expensive. In recent years, the developments of low hydrogen ferritic steel(LHF) consumables that contain no hygroscopic compounds are utilized for welding Q&T steels. Heat affected zone(HAZ) softening is another critical issue during welding of armour grade Q&T steels and it depends on the welding process employed and the weld thermal cycle. In this investigation an attempt has been made to study the influence of welding consumables and welding processes on metallurgical characteristics of armour grade Q&T steel joints by various metallurgical characterization procedures. Shielded metal arc welding(SMAW) and flux cored arc welding(FCAW) processes were used for making welds using ASS, LHF and HNS welding consumables. The joints fabricated by using LHF consumables offered lower degree of HAZ softening and there is no evidence of HIC in the joints fabricated using LHF consumables.

Scope for improved properties of dissimilar joints of ferrous and non-ferrous metals

Dissimilar joints(DSJs)of ferrous and non-ferrous metals have huge technological importance in the frontiers of newdesigns in new machineries and improved design of conventional systems.This investigation was undertaken to improve mechanicalproperties of joints of two dissimilar metals:one is Ti-based and the other is Fe-based.DSJs were processed using bonding pressurefrom1to9MPa in step of2MPa at750°C for60min.Properties of the DSJs of these two metals using different mechanisms andmethods were compared with the present research for verification.Experimental results from the diffusion bonding mechanism forjoining the dissimilar metals validated the improvement in properties.Superior mechanical properties of dissimilar-metals joints wereachieved mainly due to the third non-ferrous metallic foil,Ni of^200-?m thickness,which avoided the formation of brittleFe-Ti-based intermetallics in the diffusion zone.DSJs processed are able to achieve maximum strength of^560MPa along withsubstantial ductility of^11.9%,which is the best ever reported in the literatures so far.Work hardening effect was detected in theDSJs when the bonding was processed at5MPa and above.Bulging ratio of the non-ferrous metal(Ti-based)was much higher thanthat of the ferrous metal(SS)of the DSJs processed.SEM analysis was carried out to know the details of reaction zone,while XRDwas carried out to support the SEM results.Reasons for change in mechanical,physical,and fracture properties of the DSJs with theprocess parameter variations were clarified.