A mixed-mode forced-convection solar dryer(MMFCSD)is a device that utilizes both direct and indirect solar energy.The solar col-lector,which stores thermal energy for indirect solar uses,is an essential component of t...A mixed-mode forced-convection solar dryer(MMFCSD)is a device that utilizes both direct and indirect solar energy.The solar col-lector,which stores thermal energy for indirect solar uses,is an essential component of the dryer.Unfortunately,the thermal effi-ciency of this device is generally low.In this study,a technique was employed to improve the heat transfer of the solar collector in a MMFCSD.The technique involved adjusting the air flow pattern into a swirling flow to disturb the thermal boundary layer on the absorber plate under forced convection by using stainless wire mesh.The experiment was conducted under actual conditions and bananas were used as the drying sample.The experimental results of the thermal efficiency of the solar collector(ƞ_(solar))and the drying efficiency(ƞ_(drying))are presented.The results indicated that the air outlet temperature andƞsolar of the solar collector with stainless wire mesh were higher than the case without stainless wire mesh,reaching a maximum temperature of 46.22°C and 37.97°C,and average ƞ_(solar) of 0.26±0.02 and 0.14±0.01,respectively.The MMFCSD with stainless wire mesh had a higher ƞ_(drying) than the case without stain-less wire mesh,with values of 0.048±0.004 and 0.039±0.003,respectively,resulting in an~23.07%increase.This was attributed to the air swirling flow through the stainless wire mesh and the heat accumulation in the drying chamber,which led to an increase in the drying chamber temperature from 54.03°C to 63.60°C,an increase in the effective moisture diffusivity from 7.28×10^(-7) to 1.19×10^(-6) m^(2)/s and a decrease in the drying time of 5 h 30 min.However,further research is needed to investigate the quality of the dried sam-ples and their economic value.展开更多
基金This research project is supported by the Science Research and Innovation Fund(contract no.FF66-P1-134).We would like to thank the Development in Technology of Porous Material Research Laboratory(DiTo-Lab),Department of Mechanical Engineering,Faculty of Engineering and Technology,Rajamangala University of Technology Isan for support and permission to use the place for the research and also thank Mr Bancha Chapakdee and Mr Sila Boonsitoum,an undergraduate student of the Department of Mechanical Engineering,for collection of experimental results.
文摘A mixed-mode forced-convection solar dryer(MMFCSD)is a device that utilizes both direct and indirect solar energy.The solar col-lector,which stores thermal energy for indirect solar uses,is an essential component of the dryer.Unfortunately,the thermal effi-ciency of this device is generally low.In this study,a technique was employed to improve the heat transfer of the solar collector in a MMFCSD.The technique involved adjusting the air flow pattern into a swirling flow to disturb the thermal boundary layer on the absorber plate under forced convection by using stainless wire mesh.The experiment was conducted under actual conditions and bananas were used as the drying sample.The experimental results of the thermal efficiency of the solar collector(ƞ_(solar))and the drying efficiency(ƞ_(drying))are presented.The results indicated that the air outlet temperature andƞsolar of the solar collector with stainless wire mesh were higher than the case without stainless wire mesh,reaching a maximum temperature of 46.22°C and 37.97°C,and average ƞ_(solar) of 0.26±0.02 and 0.14±0.01,respectively.The MMFCSD with stainless wire mesh had a higher ƞ_(drying) than the case without stain-less wire mesh,with values of 0.048±0.004 and 0.039±0.003,respectively,resulting in an~23.07%increase.This was attributed to the air swirling flow through the stainless wire mesh and the heat accumulation in the drying chamber,which led to an increase in the drying chamber temperature from 54.03°C to 63.60°C,an increase in the effective moisture diffusivity from 7.28×10^(-7) to 1.19×10^(-6) m^(2)/s and a decrease in the drying time of 5 h 30 min.However,further research is needed to investigate the quality of the dried sam-ples and their economic value.
