The paper presents the principles of a method, which in two simple stages makes possible to carry out the statically calculation of values of forces acting in the fiat static indeterminate trusses. In each stage, it i...The paper presents the principles of a method, which in two simple stages makes possible to carry out the statically calculation of values of forces acting in the fiat static indeterminate trusses. In each stage, it is considered the static determinate truss, scheme of which is obtained after remove the suitable number of members from the basic static indeterminate truss. The both intermediate statically determinate trusses are of the same clear span and they are loaded by forces of half values applied to the corresponding truss nodes. The method applies one of the typical procedures of calculation of the statically determinate trusses and then it is applied in an appropriate way the rule of superposition for obtaining the final values of forces acting in particular members of the basic truss. The values of forces calculated in this way are of a very close approximation to the force values determined in the special and complex ways being considered as the exact calculation methods. The proposed method can be useful mostly but not only for the initial structural design of such systems. The simplicity of the two-stage method justifies an assumption that it can be relatively easy and worthy to adjust to the requirements of the computer aided technology of statically calculation of the complex forms of trusses.展开更多
The paper presents a very simple method, which in two stages enables to calculate the plane statically indeterminate truss by the application of one of methods used for the force calculation in members of the statical...The paper presents a very simple method, which in two stages enables to calculate the plane statically indeterminate truss by the application of one of methods used for the force calculation in members of the statically determinate trusses. The results are obtained in a very simple and quick way. Although the force values are approximated but they are relatively very close to those, which are determined by the exact methods. The point of the two-stage calculation process of the statically indeterminate trusses is to determine schemes of two independent and simple statically determined trusses, which after superposition of their patterns will give in the result a pattern of the initial, more complex form of the statically indeterminate truss. Each of the simple truss has to be of the same clear span and the load forces have to be of the half values and they have to be applied to the same nodes like in truss of the initial structural configuration.展开更多
The three-dimensional(3D)model of the middle ear is of great significance to the research of middle ear related diseases.The particular focus of this work is to simulate the impact of aircraft altitude and speed chang...The three-dimensional(3D)model of the middle ear is of great significance to the research of middle ear related diseases.The particular focus of this work is to simulate the impact of aircraft altitude and speed changes on the tympanic membrane(TM)during the descent phase,so as to analyze the pathogenesis of aero-otitis media and the mechanical response characteristics of TM under static pressure.The simulations showed that the stress and strain of TM increase as the altitude difference and speed of the aircraft increase,and the maximum stress and strain areas are consistent with the clinical observation of TM hyperemia.Therefore,among many prevention and treatment measures of aero-otitis media,it is a therapeutic method to directly balance the pressure difference between the inner and outer TM.展开更多
This paper uses a molecular static approach with a many-body potential to investigate the surface energetic and bonding characteristics of tetrahexahedral platinum nanocrystals enclosed by high-index facets such as {2...This paper uses a molecular static approach with a many-body potential to investigate the surface energetic and bonding characteristics of tetrahexahedral platinum nanocrystals enclosed by high-index facets such as {210}, {310}, {410}, {520} and {730}. It mainly focuses on the effect of crystal size and surface Miller index on these characteristics. The results show that the surface energy and dangling bond density increase with decreasing diameter of tetrahexahedral nanocrystals and generally show an order of {210} 〉{730}〉 {520} 〉 {310} 〉 {410}. However, this order is not valid at crystal sizes below 7 nm or so. The results of corresponding surfaces are also presented for comparison.展开更多
文摘The paper presents the principles of a method, which in two simple stages makes possible to carry out the statically calculation of values of forces acting in the fiat static indeterminate trusses. In each stage, it is considered the static determinate truss, scheme of which is obtained after remove the suitable number of members from the basic static indeterminate truss. The both intermediate statically determinate trusses are of the same clear span and they are loaded by forces of half values applied to the corresponding truss nodes. The method applies one of the typical procedures of calculation of the statically determinate trusses and then it is applied in an appropriate way the rule of superposition for obtaining the final values of forces acting in particular members of the basic truss. The values of forces calculated in this way are of a very close approximation to the force values determined in the special and complex ways being considered as the exact calculation methods. The proposed method can be useful mostly but not only for the initial structural design of such systems. The simplicity of the two-stage method justifies an assumption that it can be relatively easy and worthy to adjust to the requirements of the computer aided technology of statically calculation of the complex forms of trusses.
文摘The paper presents a very simple method, which in two stages enables to calculate the plane statically indeterminate truss by the application of one of methods used for the force calculation in members of the statically determinate trusses. The results are obtained in a very simple and quick way. Although the force values are approximated but they are relatively very close to those, which are determined by the exact methods. The point of the two-stage calculation process of the statically indeterminate trusses is to determine schemes of two independent and simple statically determined trusses, which after superposition of their patterns will give in the result a pattern of the initial, more complex form of the statically indeterminate truss. Each of the simple truss has to be of the same clear span and the load forces have to be of the half values and they have to be applied to the same nodes like in truss of the initial structural configuration.
基金supported by the National Natural Science Foundation of China(Grant Nos.11772087 and 12172082)。
文摘The three-dimensional(3D)model of the middle ear is of great significance to the research of middle ear related diseases.The particular focus of this work is to simulate the impact of aircraft altitude and speed changes on the tympanic membrane(TM)during the descent phase,so as to analyze the pathogenesis of aero-otitis media and the mechanical response characteristics of TM under static pressure.The simulations showed that the stress and strain of TM increase as the altitude difference and speed of the aircraft increase,and the maximum stress and strain areas are consistent with the clinical observation of TM hyperemia.Therefore,among many prevention and treatment measures of aero-otitis media,it is a therapeutic method to directly balance the pressure difference between the inner and outer TM.
基金Project supported by the International Science & Technology Cooperation Project of China (Grant No 2007DFA40890)the National Natural Science Foundation of China (Grant Nos 10702056 and 10774124)the Program for New Century Excellent Talents in Fujian Province University, China
文摘This paper uses a molecular static approach with a many-body potential to investigate the surface energetic and bonding characteristics of tetrahexahedral platinum nanocrystals enclosed by high-index facets such as {210}, {310}, {410}, {520} and {730}. It mainly focuses on the effect of crystal size and surface Miller index on these characteristics. The results show that the surface energy and dangling bond density increase with decreasing diameter of tetrahexahedral nanocrystals and generally show an order of {210} 〉{730}〉 {520} 〉 {310} 〉 {410}. However, this order is not valid at crystal sizes below 7 nm or so. The results of corresponding surfaces are also presented for comparison.
