The relationship between the microstructure transformation of type 17-4 PH stainless steel and the aging hardening behavior was investigated. The results showed that, when 17-4 PH stainless steel aging at 595℃, the b...The relationship between the microstructure transformation of type 17-4 PH stainless steel and the aging hardening behavior was investigated. The results showed that, when 17-4 PH stainless steel aging at 595℃, the bulk hardness of samples attains its peak value (42.5 HRC) for about 20 min, and then decreases at all time. TEM revealed the microstructure corresponding with peak hardness is that the fine spheroid-shape copper with the fcc crystal structure and the fiber-shape secondary carbide M23C6 precipitated from the lath martensite matrix. Both precipitations of copper and M23C6 are the reasons for strengthening of the alloy at this temperature. With the extension of holding time at this temperature, the copper and secondary carbide grow and lose the coherent relationship with the matrix, so the bulk hardness of samples decreases.展开更多
The effect of aging temperature on erosion corrosion (E-C) behavior of 17-4PH stainless steels in dilute sulphuric acid slurry containing solid particles was studied by using self-made rotating E-C apparatus. The ef...The effect of aging temperature on erosion corrosion (E-C) behavior of 17-4PH stainless steels in dilute sulphuric acid slurry containing solid particles was studied by using self-made rotating E-C apparatus. The effect of impact velocity on EC behavior of 17 4PH steels at different aging temperatures was analyzed. Surface micrographs of the specimens after E C test were observed by using scanning electron microscope (SEM). The results showed that under the condition of the same solution heat treatment, when aging temperature ranged from 400 ℃ to 610℃, the hardness reached the highest value near the temperature 460℃. The characteristics of E-C for 17-4PH stainless steels at different aging temperatures were as follows: pure erosion (wear) was dominant, corrosion was subordinate and at the same time corrosion promoted erosion. The effect of aging temperature on E-C rate of 17-4PH steels was not significant at low impact velocity, but it was found that E-C resistance of 17-4PH steels aged near 460℃ was the most excellent due to the best precipitation strengthening effect of fine and dispersed e-Cu phase. With a prerequisite of appropriate corrosion resistance, the precipitation hardening could significantly improve the E-C resistance of the materials.展开更多
The aim of this investigation is to reveal the influence of rare earths(RE) addition on mechanical properties of plasma nitrocarburized 17-4PH steel.The nitrocarburized layers were characterized by optical microscope,...The aim of this investigation is to reveal the influence of rare earths(RE) addition on mechanical properties of plasma nitrocarburized 17-4PH steel.The nitrocarburized layers were characterized by optical microscope,scanning electron microscope equipped with energy dispersive X-ray analyzer,X-ray diffractometer,microhardness tester and pin-on-disc tribometer.The results showed that RE atoms could diffuse into the surface layer of 17-4PH steel plasma nitrocarburized at 500 °C for 4 h and did not change the ...展开更多
Observation and analysis with TEM show that the fine granular dispersed carbides in hypereutectoid zone of steel 20Cr2Ni4A are distributed in the matrix of large number of lath martensite after rare earth carburizing....Observation and analysis with TEM show that the fine granular dispersed carbides in hypereutectoid zone of steel 20Cr2Ni4A are distributed in the matrix of large number of lath martensite after rare earth carburizing. But while treating by conventional carburization and double quench hardening the retained carbides are finer and more dispersive, and its matrix is perfectly twin martersite. The different micrcotructures of matrix around carbide are formed with different kinds of carburization processes.展开更多
In this paper, the orange peel defect in the surface range of the st14 steel sheet has been investigated using the electron backscattered diffraction (EBSD) technique. It has been found that the orange peel defect in ...In this paper, the orange peel defect in the surface range of the st14 steel sheet has been investigated using the electron backscattered diffraction (EBSD) technique. It has been found that the orange peel defect in the st14 steel sheet was resulted from the local coarse grains which were produced during hot-rolling due to the critical deformation in dual-phase zone. During deep drawing, the coarse grains with {100}<001> microtexture can slip on the {112}<111> slip system to form bulging and yields orange peel defects, while the coarse grains with {112}<110> orientation do not form the defect as the Schmid factor of {112}<111> slip system in it equals zero.展开更多
The microstructure, composition and shape of precipitated phase under as-cast and finished product state of 5Cr21Mn9Ni4N steel with different rare earth (RE) amount were studied. Mechanical properties of 5Cr21Mn9Ni4...The microstructure, composition and shape of precipitated phase under as-cast and finished product state of 5Cr21Mn9Ni4N steel with different rare earth (RE) amount were studied. Mechanical properties of 5Cr21Mn9Ni4N steels withont RE addition and with RE added by 0. 2% in mass percent were tested respectively. The results indicate that the solid solution amount of RE is about 10^-6 -10^-5 order of magnitude in 5Cr21Mn9Ni4N steel. Dendrite of as-cast condition is refined obviously and dimension of interstitial phase is shortened when RE is added by 0.10%-0.20%. But the microstructure will be coarser if surplus RE is added. Precipitated phase under finished product state distributes evenly in nearly same size with RE added by 0. 2% which leads to a largely improved high temperature mechanical property.展开更多
Electrochemical measurement and chemical immersion test are employed to investigate the inhibition mechanism of Na2MoO4 for carbon steel,which is studied in 55%LiBr+0.07mol/L LiOH solution at high temperature.Testing...Electrochemical measurement and chemical immersion test are employed to investigate the inhibition mechanism of Na2MoO4 for carbon steel,which is studied in 55%LiBr+0.07mol/L LiOH solution at high temperature.Testing results indicate that the passive film on carbon steel surface is mainly composed of Fe3O4,and Mo is involved in the process of film forming,in a form of MoO3 and MoO2.The parametric analysis of the evolving potential and the blend potential of MoO2 shows that Mo mainly exists as MoO2 in passive film when the concentration of Na2MoO4 is lower than 150 mg/L.While its concentration is greater than 150mg/L,it mainly exists as MoO3 inside the film and exists as MoO2 outside the film.MoO4^2- is deoxidized as MoO2 on the surface of carbon steel,which may impede the corrosion of active-site and raise the blend potential of carbon steel,and then MoO4^2- adsorbs onto the defects of the passive film and decompounds as MoO3 during the process of film forming.The electric field caused by different valence of Mo in passive film may retard the dissolution of carbon steel and lead to an increase in the polarization impedance and a decrease in hydrogen evolution.As a result,heavy concentrated Na2MoO4 solution(greater than 150mg/L)has excellent inhibition effect on carbon steel in LiBr solution.展开更多
The corrosion inhibition properties of 2,6-diphenylpiperidin-4-one (DPP) (1A) and 2,6-diphenyldihydro-2H-thiopyran-4(3H)-one (DPDT) (1B) for mild steel in 1 M phosphoric acid were studied using weight loss, potentiody...The corrosion inhibition properties of 2,6-diphenylpiperidin-4-one (DPP) (1A) and 2,6-diphenyldihydro-2H-thiopyran-4(3H)-one (DPDT) (1B) for mild steel in 1 M phosphoric acid were studied using weight loss, potentiodynamic polarization and electrochemical impedance spectroscopic techniques. The effect of temperature on the corrosion behavior of mild steel has been examined in the temperature range 303 - 328 K. The inhibition efficiency increases with increasing inhibitor concentration but decreases with increasing temperature. Potentiodynamic polarization studies indicated the mixed nature of inhibitors. The adsorption of the inhibitors on mild steel surface obeyed the Langmuir adsorption isotherms. The density functional theory (DFT) at the B3LYP/6- 31G (d) basis set level was performed on 1A and 1B to investigate the correlation between molecular structure and the corresponding inhibition efficiency (%). The quantum chemical parameters such as EHOMO, ELUMO, the energy gap (E), hardness (η), softness (S), dipole moment (μ), electron affinity (A), ionization potential (I), the absolute electronegativity (χ), the fraction of electron transferred (N), electrophilicity index (ω), the back-donation (EBack-donation) and Mulliken population analysis have been calculated.展开更多
Titanium alloy (Ti6Al4V) and low carbon steel (LCS) were joined by explosive welding method using different ratios of explosive. Some metallurgical properties of joined samples were investigated. Joined samples we...Titanium alloy (Ti6Al4V) and low carbon steel (LCS) were joined by explosive welding method using different ratios of explosive. Some metallurgical properties of joined samples were investigated. Joined samples were examined by means of optical microscope, scanning electron microscope (SEM) and tensile-shearing tests. Bending, tensile, hardness and corrosion behaviour of the samples were investigated. Separation was not occurred on the joining interface after tensile-shearing and bending tests. It is seen that hardness of both plates were increased with increasing explosive. It is found that increasing explosive ratio leads to an increase in corrosion. It is also found that corrosion rate was high at the beginning of the experiment but the rate of the corrosion decreased subsequently during the experiment.展开更多
Microstructure of the deepest zone of high speed steel W6Mo5Cr4V2(M2)melt after laser fu-sion was found to be so fine as the ehill zone of a solidified ingot.When narrower chill zoneformed,the long columnar dendrites ...Microstructure of the deepest zone of high speed steel W6Mo5Cr4V2(M2)melt after laser fu-sion was found to be so fine as the ehill zone of a solidified ingot.When narrower chill zoneformed,the long columnar dendrites grow into the melt and then the fine equiaxed cellularstructure appears in upper melt region nearly surface.The substructure of cellular grains anddendrites was observed to consist of martensite and retained austenile,while the carbides asM_6C_■ Cr_7C_3 and MC distributed at their boundaries.It is believed that the highermicrohardness up to HV_(0.1)=865-960 of the laser fused structure of the alloy is due to the oc-currence of martensite.展开更多
基金This work was financially supported by the Key Nuclear Fuel and Nuclear Materials Laboratory of China(No.51481080104ZS8501).
文摘The relationship between the microstructure transformation of type 17-4 PH stainless steel and the aging hardening behavior was investigated. The results showed that, when 17-4 PH stainless steel aging at 595℃, the bulk hardness of samples attains its peak value (42.5 HRC) for about 20 min, and then decreases at all time. TEM revealed the microstructure corresponding with peak hardness is that the fine spheroid-shape copper with the fcc crystal structure and the fiber-shape secondary carbide M23C6 precipitated from the lath martensite matrix. Both precipitations of copper and M23C6 are the reasons for strengthening of the alloy at this temperature. With the extension of holding time at this temperature, the copper and secondary carbide grow and lose the coherent relationship with the matrix, so the bulk hardness of samples decreases.
文摘The effect of aging temperature on erosion corrosion (E-C) behavior of 17-4PH stainless steels in dilute sulphuric acid slurry containing solid particles was studied by using self-made rotating E-C apparatus. The effect of impact velocity on EC behavior of 17 4PH steels at different aging temperatures was analyzed. Surface micrographs of the specimens after E C test were observed by using scanning electron microscope (SEM). The results showed that under the condition of the same solution heat treatment, when aging temperature ranged from 400 ℃ to 610℃, the hardness reached the highest value near the temperature 460℃. The characteristics of E-C for 17-4PH stainless steels at different aging temperatures were as follows: pure erosion (wear) was dominant, corrosion was subordinate and at the same time corrosion promoted erosion. The effect of aging temperature on E-C rate of 17-4PH steels was not significant at low impact velocity, but it was found that E-C resistance of 17-4PH steels aged near 460℃ was the most excellent due to the best precipitation strengthening effect of fine and dispersed e-Cu phase. With a prerequisite of appropriate corrosion resistance, the precipitation hardening could significantly improve the E-C resistance of the materials.
基金supported by the National Natural Science Foundation of China (50871035)the Ph.D. Programs Foundation of Ministry of Education of China (20060213017)
文摘The aim of this investigation is to reveal the influence of rare earths(RE) addition on mechanical properties of plasma nitrocarburized 17-4PH steel.The nitrocarburized layers were characterized by optical microscope,scanning electron microscope equipped with energy dispersive X-ray analyzer,X-ray diffractometer,microhardness tester and pin-on-disc tribometer.The results showed that RE atoms could diffuse into the surface layer of 17-4PH steel plasma nitrocarburized at 500 °C for 4 h and did not change the ...
文摘Observation and analysis with TEM show that the fine granular dispersed carbides in hypereutectoid zone of steel 20Cr2Ni4A are distributed in the matrix of large number of lath martensite after rare earth carburizing. But while treating by conventional carburization and double quench hardening the retained carbides are finer and more dispersive, and its matrix is perfectly twin martersite. The different micrcotructures of matrix around carbide are formed with different kinds of carburization processes.
基金This work was supported by the National Natural Science Foundation of China under grant No.50171040.
文摘In this paper, the orange peel defect in the surface range of the st14 steel sheet has been investigated using the electron backscattered diffraction (EBSD) technique. It has been found that the orange peel defect in the st14 steel sheet was resulted from the local coarse grains which were produced during hot-rolling due to the critical deformation in dual-phase zone. During deep drawing, the coarse grains with {100}<001> microtexture can slip on the {112}<111> slip system to form bulging and yields orange peel defects, while the coarse grains with {112}<110> orientation do not form the defect as the Schmid factor of {112}<111> slip system in it equals zero.
文摘The microstructure, composition and shape of precipitated phase under as-cast and finished product state of 5Cr21Mn9Ni4N steel with different rare earth (RE) amount were studied. Mechanical properties of 5Cr21Mn9Ni4N steels withont RE addition and with RE added by 0. 2% in mass percent were tested respectively. The results indicate that the solid solution amount of RE is about 10^-6 -10^-5 order of magnitude in 5Cr21Mn9Ni4N steel. Dendrite of as-cast condition is refined obviously and dimension of interstitial phase is shortened when RE is added by 0.10%-0.20%. But the microstructure will be coarser if surplus RE is added. Precipitated phase under finished product state distributes evenly in nearly same size with RE added by 0. 2% which leads to a largely improved high temperature mechanical property.
文摘Electrochemical measurement and chemical immersion test are employed to investigate the inhibition mechanism of Na2MoO4 for carbon steel,which is studied in 55%LiBr+0.07mol/L LiOH solution at high temperature.Testing results indicate that the passive film on carbon steel surface is mainly composed of Fe3O4,and Mo is involved in the process of film forming,in a form of MoO3 and MoO2.The parametric analysis of the evolving potential and the blend potential of MoO2 shows that Mo mainly exists as MoO2 in passive film when the concentration of Na2MoO4 is lower than 150 mg/L.While its concentration is greater than 150mg/L,it mainly exists as MoO3 inside the film and exists as MoO2 outside the film.MoO4^2- is deoxidized as MoO2 on the surface of carbon steel,which may impede the corrosion of active-site and raise the blend potential of carbon steel,and then MoO4^2- adsorbs onto the defects of the passive film and decompounds as MoO3 during the process of film forming.The electric field caused by different valence of Mo in passive film may retard the dissolution of carbon steel and lead to an increase in the polarization impedance and a decrease in hydrogen evolution.As a result,heavy concentrated Na2MoO4 solution(greater than 150mg/L)has excellent inhibition effect on carbon steel in LiBr solution.
文摘The corrosion inhibition properties of 2,6-diphenylpiperidin-4-one (DPP) (1A) and 2,6-diphenyldihydro-2H-thiopyran-4(3H)-one (DPDT) (1B) for mild steel in 1 M phosphoric acid were studied using weight loss, potentiodynamic polarization and electrochemical impedance spectroscopic techniques. The effect of temperature on the corrosion behavior of mild steel has been examined in the temperature range 303 - 328 K. The inhibition efficiency increases with increasing inhibitor concentration but decreases with increasing temperature. Potentiodynamic polarization studies indicated the mixed nature of inhibitors. The adsorption of the inhibitors on mild steel surface obeyed the Langmuir adsorption isotherms. The density functional theory (DFT) at the B3LYP/6- 31G (d) basis set level was performed on 1A and 1B to investigate the correlation between molecular structure and the corresponding inhibition efficiency (%). The quantum chemical parameters such as EHOMO, ELUMO, the energy gap (E), hardness (η), softness (S), dipole moment (μ), electron affinity (A), ionization potential (I), the absolute electronegativity (χ), the fraction of electron transferred (N), electrophilicity index (ω), the back-donation (EBack-donation) and Mulliken population analysis have been calculated.
文摘Titanium alloy (Ti6Al4V) and low carbon steel (LCS) were joined by explosive welding method using different ratios of explosive. Some metallurgical properties of joined samples were investigated. Joined samples were examined by means of optical microscope, scanning electron microscope (SEM) and tensile-shearing tests. Bending, tensile, hardness and corrosion behaviour of the samples were investigated. Separation was not occurred on the joining interface after tensile-shearing and bending tests. It is seen that hardness of both plates were increased with increasing explosive. It is found that increasing explosive ratio leads to an increase in corrosion. It is also found that corrosion rate was high at the beginning of the experiment but the rate of the corrosion decreased subsequently during the experiment.
文摘Microstructure of the deepest zone of high speed steel W6Mo5Cr4V2(M2)melt after laser fu-sion was found to be so fine as the ehill zone of a solidified ingot.When narrower chill zoneformed,the long columnar dendrites grow into the melt and then the fine equiaxed cellularstructure appears in upper melt region nearly surface.The substructure of cellular grains anddendrites was observed to consist of martensite and retained austenile,while the carbides asM_6C_■ Cr_7C_3 and MC distributed at their boundaries.It is believed that the highermicrohardness up to HV_(0.1)=865-960 of the laser fused structure of the alloy is due to the oc-currence of martensite.