A low carbon steel was used to determine the critical strain εc for completion of deformation enhanced ferrite transformation （DEFT） through a series of hot compression tests. In addition, the influence of prior au...A low carbon steel was used to determine the critical strain εc for completion of deformation enhanced ferrite transformation （DEFT） through a series of hot compression tests. In addition, the influence of prior austenite grain size （PAGS） on the critical strain was systematically investigated. Experimental results showed that the critical strain is affected by PAGS. When γ→α transformation completes, the smaller the PAGS is, the smaller the critical strain is. The ferrite grains obtained through DEFT can be refined to about 3 μm when the DEFT is completed.展开更多
The change of inclusions and microstructure of 16Mn steel treated by Ce were observed,and the effect of austenitizing temperature on the microstructure was also examined.The results show that the inclusions are transf...The change of inclusions and microstructure of 16Mn steel treated by Ce were observed,and the effect of austenitizing temperature on the microstructure was also examined.The results show that the inclusions are transformed from Si-Mn-Al composite oxide and MnS into AlCeO3,Ce2O2S,and MnS composite inclusions after being treated by Ce.Plenty of intragranular ferrites are formed in 16Mn steel containing～0.017wt% Ce.A large amount of intragranular acicular ferrites are formed after being austenitized for 20min at 1473 K.The prior austenite grain size fit for the formation of intragranular acicular ferrites is about 120μm.展开更多
The transformation behaviors and microstructures of a low carbon multi-phase steel were investigated by the simulation of deformation-relaxation-accelerated cooling processing,using a Gleeble 3500 thermal-mechanical s...The transformation behaviors and microstructures of a low carbon multi-phase steel were investigated by the simulation of deformation-relaxation-accelerated cooling processing,using a Gleeble 3500 thermal-mechanical simulator.A pre-treatment of solid solution at 1200°C was implemented to minimize the influence on transformation from solid solution/precipitation qualities of 0.08%Nb in this steel.On this basis,the effect of austenite grain size and accelerated cooling start temperature were studied individually.The results indicated that the transformation of ferrite in multi-phase steel could be significantly promoted by the refinement of austenite grains and the increase of relaxation time,while the hard phase,such as lath bainite or martensite,could still be obtained with the following accelerated cooling.In contrast,more uniform lower temperature transformed microstructure could form from coarse grain austenite.The potential benefit of austenite grain size on adjusting the proportion of phases in multiphase steel was also discussed.展开更多
基金This work was financially supported by the National Science and Technology Ministry to the research project ‘Advanced industriali-zation technique of manufacture for carbon steel of 500 MPa grade’ (No.2001AA332020).
文摘A low carbon steel was used to determine the critical strain εc for completion of deformation enhanced ferrite transformation （DEFT） through a series of hot compression tests. In addition, the influence of prior austenite grain size （PAGS） on the critical strain was systematically investigated. Experimental results showed that the critical strain is affected by PAGS. When γ→α transformation completes, the smaller the PAGS is, the smaller the critical strain is. The ferrite grains obtained through DEFT can be refined to about 3 μm when the DEFT is completed.
基金supported by the National Natural Science Foundations of China (No.50734008)the Fundamental Research Funds for the Central Universities (No.FRF-AS-11-003A)
文摘The change of inclusions and microstructure of 16Mn steel treated by Ce were observed,and the effect of austenitizing temperature on the microstructure was also examined.The results show that the inclusions are transformed from Si-Mn-Al composite oxide and MnS into AlCeO3,Ce2O2S,and MnS composite inclusions after being treated by Ce.Plenty of intragranular ferrites are formed in 16Mn steel containing～0.017wt% Ce.A large amount of intragranular acicular ferrites are formed after being austenitized for 20min at 1473 K.The prior austenite grain size fit for the formation of intragranular acicular ferrites is about 120μm.
基金supported by the National Basic Research Program of China ("973" Program) (Grant No. 2010CB630801)
文摘The transformation behaviors and microstructures of a low carbon multi-phase steel were investigated by the simulation of deformation-relaxation-accelerated cooling processing,using a Gleeble 3500 thermal-mechanical simulator.A pre-treatment of solid solution at 1200°C was implemented to minimize the influence on transformation from solid solution/precipitation qualities of 0.08%Nb in this steel.On this basis,the effect of austenite grain size and accelerated cooling start temperature were studied individually.The results indicated that the transformation of ferrite in multi-phase steel could be significantly promoted by the refinement of austenite grains and the increase of relaxation time,while the hard phase,such as lath bainite or martensite,could still be obtained with the following accelerated cooling.In contrast,more uniform lower temperature transformed microstructure could form from coarse grain austenite.The potential benefit of austenite grain size on adjusting the proportion of phases in multiphase steel was also discussed.
