Hysteretic behavior of special shaped columns composed of steel and reinforced concrete(SRC)

This paper describes a series of experimental investigations on seventeen specimens of steel reinforced concrete special shaped(SRCSS) columns under low cyclic reversed loading using parallel crosshead equipment. Nine T-shaped SRC columns, four L-shaped SRC columns and four +-shaped SRC columns were tested to examine the effects of shape steel confi guration, loading angle, axial compressive ratio and shear-span ratio on the behavior(strength, stiffness, energy dissipation, ductility, etc.) of SRCSS column specimens. The failure modes and hysteretic performance of all the specimens were obtained in the tests. Test results demonstrate that the shear-span ratio is the main parameter affecting the failure modes of SRCSS columns. The specimens with small shear-span ratio are prone to shear failure, and the primary failure planes in SRCSS columns are parallel to the loading direction. As a result, there is a symmetry between positive and negative loading directions in the hysteretic curves of the SRCSS columns. The majority of displacement ductility coeffi cients for all the specimens are over 3.0, so that the SRCSS columns demonstrate a better deformation capacity. In addition, the equivalent viscous damping coeffi cients of all the specimens are greater than 0.2, indicating that the seismic behavior of SRCSS columns is adequate. Finally, the superposition theory was used to calculate the limits of axial compressive ratio for the specimens, and it is found that the test axial compressive ratio is close to or smaller than the calculated axial compressive ratio limit.

Seismic strengthening of reinforced concrete columns damaged by rebar corrosion using combined CFRP and steel jacket

In order to study the effectiveness of combined carbon fiber-reinforced polymer （CFRP） sheets and steel jacket in strengthening the seismic performance of corrosion-damaged reinforced concrete （RC） columns, twelve reinforced concrete columns are tested under combined lateral cyclic displacement excursions and constant axial load. The variables studied in this program include effects of corrosion degree of the rebars, level of axial load, the amount of CFRP sheets and steel jacket. The results indicate that the combined CFRP and steel jacket retrofitting technique is effective in improving load-carrying, ductility and energy absorption capacity of the columns. Compared with the corrosion-damaged RC column, the lateral load and the ductility factor of many strengthened columns increase more than 90% and 100%, respectively. The formulae for the calculation of the yielding load, the maximum lateral load and the displacement ductility factor of the strengthened columns under combined constant axial load and cyclically increasing lateral loading are developed. The test results are also compared with the results obtained from the proposed formulae. A good agreement between calculated values and experimental results is observed.

Seismic Performance of Steel Reinforced Ultra High-strength Concrete Columns

The seismic performance of steel reinforced ultra-high-strength concrete columns(SRSHC) with various shear-span ratios(λ) were studied through a series of experiments.The concrete compressive cube strength value of experimental specimens ranged from 92.9 MPa to 108.1 MPa.The main experimental variables affecting seismic performance of specimens were axial load ratio and stirrup reinforcement ratio.The columns(λ=2.75) subjected to low cyclic reversed lateral loads failed mainly in the flexural-shear mode failure and columns(λ≤2.0) subjected to low cyclic reversed lateral loads failed mainly in the shear mode failure.Shear force-displacement hysteretic curves and skeleton curves were drawn.Coefficient of the specimen displacement ductility was calculated.Experimental results indicate that ductility decreases with axial pressure ratio increasing,and increases with stirrup reinforcement ratio increasing.Limit values of axial pressure ratio and minimum stirrup reinforcement ratio of columns are proposed to satisfy definite ductility requirement.The suggested values provide a reference for engineering application and for the amendment of the current Chinese design code of steel reinforced concrete composite structures.

Seismic Behaviour of Beam-Column Joints of Precast and Partial Steel Reinforced Concrete

A beam-column joint of precast and partial steel reinforced concrete( PPSRC) is proposed for precast reinforced concrete frames. The PPSRC consists of partial steel and reinforced concrete. The partial steel is located in the core joint region and the connections between concrete members. This paper presents an experimental study of a series of PPSRC specimens. These specimens are tested under low cyclic loading.Experimental results demonstrate that the bearing capacity of the PPSRC specimens is 3 times that of the ordinary reinforced concrete( RC) beam-column joints. The strength and stiffness degradation rates are slower compared with that of the RC beam-column joints. In addition,the strength of the core joint region and the connections is higher than other parts of the PPSRC specimens. Beam failure occurs firstly for the PPSRC specimens,followed by column failure and connections failure. The failure of the core joint region occurs finally.Test results show that the seismic performance of the PPSRC is better than that of the ordinary RC beam-column joints.

Seismic performance of steel reinforced ultra high-strength concrete composite frame joints

To investigate the seismic performance of a composite frame comprised of steel reinforced ultra high-strength concrete （SRUHSC） columns and steel reinforced concrete （SRC） beams, six interior frame joint specimens were designed and tested under low cyclically lateral load. The effects of the axial load ratio and volumetric stirrup ratio were studied on the characteristics of the frame joint performance including crack pattern, failure mode, ductility, energy dissipation capacity, strength degradation and rigidity degradation. It was found that all joint specimens behaved in a ductile manner with flexural-shear failure in the joint core region while plastic hinges appeared at the beam ends. The ductility and energy absorption capacity of joints increased as the axial load ratio decreased and the volumetric stirIup ratio increased. The displacement ductility coefficient and equivalent damping coefficient of the joints fell between the corresponding coefficients of the steel reinforced concrete （SRC） frame joint and RC frame joint. The axial load ratio and volumetric stirrup ratio have less influence on the strength degradation and more influence on the stiffness degradation. The stiffness of the joint degrades more significantly for a low volumetric stirrup ratio and high axial load ratio. The characteristics obtained from the SRUHSC composite frame joint specimens with better seismic performance may be a useful reference in future engineering applications.

Axial Bearing Capacity of Short FRP Confined Concrete-filled Steel Tubular Columns

The bearing capacity of FRP confined concrete-filled steel tubular （FRP-CFST） columns under axial compression was investigated. This new type of composite column is a concrete-filled steel tube （CFST） confined with fiber-reinforced polymer （FRP） wraps. Totally 11 short column specimens were tested to failure under axial compression. The influences of the type and quantity of FRP, the thickness of steel tube and the concrete strength were studied. It was found that the bearing capacity of short FRP-CFST column was much higher than that of comparable CFST column. Furthermore, the formulas for calculating the bearing capacity of the FRP-CFST columns are proposed. The analytical calculated results agree well with the experimental results.

Seismic behavior of large-scale FRP–recycled aggregate concrete–steel columns with shear connectors

The application of fi ber-reinforced polymer (FRP) composites for the development of high-performance composite structural systems has received signifi cant recent research attention. A composite of FRP–recycled aggregate concrete (RAC)–steel column (FRSC), consisting of an outer FRP tube, an inner steel tube and annular RAC fi lled between two tubes, is proposed herein to facilitate green disposal of demolished concrete and to improve the ductility of concrete columns for earthquake resistance. To better understand the seismic behavior of FRSCs, quasi-static tests of large-scale basalt FRSCs with shear connectors were conducted. The infl uence of the recycled coarse aggregate (RCA) replacement percentage, shear connectors and axial loading method on the lateral load and deformation capacity, energy dissipation and cumulative damage were analyzed to evaluate the seismic behavior of FRSCs. The test results show that FRSCs have good seismic behavior, which was evidenced by high lateral loads, excellent ductility and energy dissipation capacity, indicating RAC is applicable in FRSCs. Shear connectors can signifi cantly postpone the steel buckling and increase the lateral loads of FRSCs, but weaken the deformation capacity and energy dissipation performance.

Test on mechanical behavior of SRC L-shaped columns under combined torsion and bending moment

Investigations of the seismic behavior of steel reinforced concrete L-shaped columns under constant axial compression and cycled bending-shear-torsion load were performed.Six specimens,which considered two parameters,i.e.,the moment ratio of torsion to bending(γ)and the aspect ratio(column length-to-depth ratio,φ),were prepared for the experiment.In this study,the failure process,torsion-displacement hysteresis curves,and flexure-displacement hysteresis curves were obtained.The failure characteristics,mechanical behavior of specimens such as the failure patterns,hysteresis curves,rigidity degradation,ductility and energy dissipation,are analyzed.The experimental research indicated that the major failures of the specimens were bending failure,bending-shear failure and bending-torsion failure as the moment ratio of torsion to bending(γ)increased.The torsion-displacement hysteresis curves were pinched in the middle,formed a slip platform,and the phenomenon of“load drop”occurred after the peak load.The bending-displacement hysteresis curves were plump,which showed that bending capacity of the specimen was better than its torsion capacity.Additionally,the energy dissipation of the specimen was dominated by torsion in the early stage and ultimately governed by the bending moment in the later phase.Test results also indicated that the displacement ductility coefficient and interstory rotation angle of the failure point were less than 3.0 and 1/50,respectively,which means the test specimen performance does not meet the requirement of the Chinese Code for Seismic Design of Buildings(GB 50011-2014)in this respect.

Seismic behavior of thin-walled circular and stiffened square steel tubed-reinforced-concrete columns

Steel tubed-reinforced-concrete(TRC) columns have been gradually used in the construction of high-rise buildings recently because of their high axial load-carrying capacities and excellent seismic behavior. Existing studies about their seismic behavior were focused on columns with relatively thick tubes, i.e., diameter-to-thickness/width-to-thickness(D/t) ratios were below 100,while little is known about thin-walled TRC columns, especially for square TRC columns. Considering the infilled concrete of square TRC columns is non-uniformly and non-effectively confined, accordingly, stiffened square TRC columns are usually adopted in practice. Thus, two thin-walled circular TRC columns(D/t=120) and two stiffened square ones with diagonal stiffeners in plastic hinge regions(D/t=106) were tested under a constant axial compression combined with cyclic lateral loading.Both the circular and stiffened square TRC columns had the same cross sectional area, tube thickness, reinforcing bar ratio and column height. Flexural failure occurred for all the four specimens. Test results showed the strengths of the stiffened square TRC columns were a little higher in comparison to their circular counterparts; the ductility and energy dissipation capacities were excellent for both the stiffened and circular TRC columns, indicating very good confinement was gained from the yielded steel tubes of the plastic hinge regions at the peak loads. And shear stresses(35–90 MPa) in the sheared plates showed their moderate contribution of carrying lateral loads. Finally, cross sectional capacity analysis results demonstrated the method for TRC columns is acceptable for the stiffened square TRC columns.

Axial compression tests and numerical simulation of steel reinforced recycled concrete short columns confined by carbon fiber reinforced plastics strips

To research the axial compression behavior of steel reinforced recycled concrete(SRRC)short columns confined by carbon fiber reinforced plastics(CFRP)strips,nine scaled specimens of SRRC short columns were fabricated and tested under axial compression loading.Subsequently,the failure process and failure modes were observed,and load-displacement curves as well as the strain of various materials were analyzed.The effects on the substitution percentage of recycled coarse aggregate(RCA),width of CFRP strips,spacing of CFRP strips and strength of recycled aggregate concrete(RAC)on the axial compression properties of columns were also analyzed in the experimental investigation.Furthermore,the finite element model of columns which can consider the adverse influence of RCA and the constraint effect of CFRP strips was founded by ABAQUS software and the nonlinear parameter analysis of columns was also implemented in this study.The results show that the first to reach the yield state was the profile steel in the columns,then the longitudinal rebars and stirrups yielded successively,and finally RAC was crushed as well as the CFRP strips was also broken.The replacement rate of RCA has little effect on the columns,and with the substitution rate of RCA from 0 to 100%,the bearing capacity of columns decreased by only 4.8%.Increasing the CFRP strips width or decreasing the CFRP strips spacing could enhance the axial bearing capacity of columns,the maximum increase was 10.5%or 11.4%,and the ductility of columns was significantly enhanced.Obviously,CFRP strips are conducive to enhance the axial bearing capacity and deformation capacity of columns.On this basis,considering the restraint effect of CFRP strips and the adverse effects of RCA,the revised formulas for calculating the axial bearing capacity of SRRC short columns confined by CFRP strips were proposed.

反复荷载下圆钢管型钢再生混凝土组合柱恢复力模型研究

为建立圆钢管型钢再生混凝土组合柱的恢复力模型,对11根圆钢管型钢再生混凝土组合柱试件进行了低周反复荷载试验研究,考虑了再生骨料取代率、配钢率及钢管径厚比等不同设计参数的影响,分析了组合柱的地震破坏形态及滞回性能。基于组合柱的力学特征及曲线形状,提出了圆钢管型钢再生混凝土组合柱骨架曲线的三折线参数模型,采用理论推导与数据拟合的方法确定了组合柱骨架曲线的模型参数。在此基础上,给出了组合柱的滞回规则和卸载规律,构建了组合柱的恢复力模型,计算滞回曲线与试验滞回曲线吻合良好,表明该恢复力模型较好地反映了反复荷载下组合柱的受力特征点及滞回性能,可为此类组合柱的推广提供技术参考。

设有叠合柱的局部错层RC框架结构地震易损性分析

为研究某一设有叠合柱的局部错层钢筋混凝土(reinforced concrete,RC)框架结构在近断层和远场地震作用下的破坏概率,自定义钢管混凝土叠合柱塑性铰参数,并与试验对比验证塑性铰参数的有效性。采用SAP2000建立非线性分析模型,选取近断层和远场地震波共22条,分别以地震峰值加速度(peak ground acceleration,PGA)和最大层间位移角作为地震动强度指标和结构性能指标,基于增量动力分析(incremental dynamic analysis,IDA)结果和点估计函数对错层框架结构进行易损性分析。结果表明:对于远场地震动,结构满足“三水准”抗震设防要求,在罕遇地震下超越防止倒塌极限状态的概率仅为0.24%;结构在近断层多遇地震下仍能满足“小震不坏”的设计要求,设防地震下结构超越修复后使用极限状态的概率为53.63%,发生中等破坏的概率较大,罕遇地震下结构达到倒塌极限状态的概率为5.37%,较远场地震作用破坏更为严重。研究结果可为错层框架结构的设计和地震风险评估提供参考。

内置型钢增强钢管约束钢筋混凝土柱节点抗震性能研究

采用钢管对传统RC柱进行约束,形成的钢管约束钢筋混凝土(STRC)柱具有优越的承载能力和耗能性能。但在应用于框架节点设计时,节点区域仍采用普通RC柱节点构造,可能导致节点处没有钢管约束而成为薄弱点,节点处易发生破坏。针对钢管约束钢筋混凝土(STRC)柱节点抗震性能薄弱的现状,提出采用内置型钢短柱进行增强。基于ABAQUS工作平台对具有相同构造形式的节点试件建立有限元模型,将数值计算所得破坏形态、滞回曲线和型钢应力与试验结果进行对比,两者吻合较好,在此基础上探讨内置型钢长度和轴压比对节点抗震性能的影响。结果表明:随着内置型钢长度增加,试件的承载力、极限位移和延性均有不同程度的提升,轴压比对试件受力性能影响较小。通过进一步分析试件的破坏机制、型钢抗弯性能和耗能能力,提出满足节点抗震性能需求的内置型钢长度建议取值。

圆钢管型钢再生混凝土组合柱水平承载力计算方法研究

通过对11个圆钢管型钢再生混凝土组合柱进行低周反复荷载试验,分析再生粗骨料取代率、型钢截面形式、轴压比、型钢配钢率及圆钢管壁厚参数对组合柱水平承载力的影响规律;观察了组合柱的破坏形态及特征,研究了圆钢管、型钢翼缘及腹板应变的发展规律,分析了组合柱的地震破坏特征。研究表明,在水平地震作用下组合柱发生典型的压弯塑性铰破坏。在此基础上,结合现有规范提出了基于叠加原理的圆钢管型钢再生混凝土组合柱水平承载力计算方法。计算结果表明,其水平承载力计算值与试验值吻合度较好,能较为准确地预测组合柱的水平承载力。

功能可恢复RCS混合框架结构研究进展

钢筋混凝土柱-钢梁(RCS)混合框架结构以其结合了混凝土优异的抗压性能及钢材优异的抗弯性能而受到广泛关注,而可恢复功能结构以其震后快速恢复使用功能的能力,也成为地震工程界研究的新热点。功能可恢复RCS混合框架结构可以在弯矩较大的梁端和柱脚部位设置可更换构件,实现结构的功能可恢复能力。文中简述了近年来功能可恢复RCS混合框架结构研究进展,重点关注各类型功能可恢复钢梁、功能可恢复摇摆柱脚的构造研究,介绍了功能可恢复RCS混合框架结构性能分析研究进展。最后,对功能可恢复RCS混合框架结构仍需深入研究的问题进行了展望。

冻融循环对十字形型钢混凝土柱轴压性能影响分析

为探究十字形型钢混凝土(SRC)柱经冻融作用后力学性能的演变,考虑混凝土强度、配筋率及长细比三个影响因素,采用ABAQUS软件对十字形SRC柱进行冻融和压缩模拟研究,对比分析冻融循环对十字形SRC柱荷载-应变曲线及承载力退化规律的影响,并归纳总结其承载力退化系数表达式.结果表明:SRC试件极限承载力与冻融循环次数呈负相关趋势,冻融循环导致混凝土劣化,使构件轴压承载能力降低,100次冻融循环后,SRC柱的极限承载力最大下降8.48%;而构件轴压承载能力与配筋率呈正相关趋势,因此适当提高混凝土强度及配筋率可有效抵御构件的冻融损伤;此外,极限承载力与长细比成反比,长细比过大,构件易发生弯曲失稳破坏;所提出轴压承载力退化系数计算值与模拟值吻合度较好.

铅黏弹性阻尼器增强钢管约束钢筋混凝土柱节点抗震性能研究

针对钢管约束钢筋混凝土(steel tubed reinforced concrete,STRC)柱节点抗震性能薄弱的现状,提出采用改良的铅黏弹性阻尼器进行增强。基于ABAQUS工作平台对铅黏弹性阻尼器试件建立有限元模型,将数值计算所得滞回和骨架曲线、耗能性能及疲劳性能与试验结果进行对比,两者吻合较好。在此基础上探讨了铅芯直径、铅芯布置形式及复合黏弹性体厚度比值对铅黏弹性阻尼器力学性能的影响。结果表明:相较于扇形铅黏弹性阻尼器,改良后的四边形铅黏弹性阻尼器表现出更好的力学性能;随着铅芯直径的增大,阻尼器的耗能能力指标均得到大幅提高;建议铅芯个数取2个,铅芯面积与复合黏弹性层面积比值取6%~8%,复合黏弹性体厚度比值约为0.67。建立不同布置方案的铅黏弹性阻尼器增强STRC柱节点试件模型,对其破坏形态、滞回特性和箍筋应力进行对比分析,给出合理的布置方案,为实际工程提供参考。

高强型钢超高性能混凝土短柱轴压性能试验及其有限元分析

为研究高强型钢超高性能混凝土短柱的轴压性能,对试件进行了轴心受压试验,设计参数包括配钢率、箍筋间距和箍筋形式。观察了试件的轴压破坏过程,获得了破坏形态及轴向荷载-位移曲线,分析了承载能力、变形能力、刚度等轴压性能指标,以及超高性能混凝土、纵筋、箍筋和型钢的应变发展规律。在试验研究基础上,采用ABAQUS建立了高强型钢超高性能混凝土短柱轴压性能有限元分析模型,计算结果与试验结果吻合较好,进而进行了参数分析。结果表明:试件发生的是典型轴压破坏,中部表面出现“锯齿形”裂缝;轴向荷载-位移曲线会出现2次荷载峰值;箍筋间距减小时,试件的承载能力和变形能力均提高,但刚度退化速率没有显著变化;配钢率增大时,试件的承载能力提高,变形能力先增大后减小,刚度退化变缓;型钢强度增大时,试件的承载能力和变形能力均提高,提高速度先快后慢;超高性能混凝土抗压强度增大时,试件的承载能力提高,变形能力降低;超高性能混凝土受拉能够达到峰值应变;纵筋在极限点之前发生受压屈服;箍筋在极限点时应变不足屈服应变的1/3,但在破坏点前达到受拉屈服;型钢翼缘在极限点前后发生屈服,腹板屈服晚于翼缘。

圆钢管型钢再生混凝土组合柱滞回性能非线性有限元分析

基于圆钢管型钢再生混凝土组合柱低周反复荷载试验研究,采用OpenSees软件对该组合柱进行了滞回性能数值分析,获取了组合柱的滞回曲线及抗震性能指标,并与试验结果进行了比较,验证了组合柱数值模型的合理性。在此基础上,对组合柱的滞回性能开展了参数影响分析。结果表明:再生骨料取代率从0增大到100%,组合柱的峰值荷载下降了7.78%,延性略有降低;提高再生混凝土强度、型钢强度及圆钢管强度,对于提升组合柱的承载力及刚度是有利的,但却使组合柱的脆性增大;随着轴压比的增大,组合柱的承载力呈现先上升后下降的趋势,而延性逐渐变差;型钢配钢率从5.54%增至9.99%,组合柱的峰值荷载提高了24.34%,但对于改善组合柱的延性不明显;增大钢管壁厚对组合柱的承载力和延性均是有利的。

负载下活性粉末混凝土钢筋网加固足尺混凝土柱轴压性能试验研究

为提高负载下钢筋混凝土(RC)柱的轴心抗压性能,使用活性粉末混凝土钢筋网(RPCSM)对负载下的RC足尺柱进行加固,设计制作了7根RC方柱试件,其中1根未加固对比柱、1根端部箍筋加密加固柱、2根RPCSM加固柱、3根端部箍筋加密RPCSM加固柱。考虑加固层厚度、钢筋网配筋率和端部箍筋加密对轴心受压RC柱性能的影响,进行了试验研究并分析了各试件的破坏模式、荷载-变形关系和应变变化规律。结果表明:加固柱的承载力提高了2.81~3.82倍;原混凝土柱与RPCSM加固层界面粘结可靠,共同工作良好;随着钢筋网配筋率的提高以及加固层厚度的增加,端部箍筋加密后整体性的提高,承载力和轴向变形能力提高,但延性有所下降。结合规范和破坏机理,给出了承载力计算公式,以促进该加固技术的推广。