Numerical Simulation Analysis of Welded Joints in Arch Ribs of Large Span Steel Pipe Arch Bridges

In order to study the residual stress distribution law of welded joints of arch ribs of large-span steel pipe concrete arch bridges,numerical simulation of temperature,stress and strain fields based on ABAQUS for welded joints of arch-ribbed steel tubes using 7-,8-and 9-layer welds is carried out and its accuracy is demonstrated.The steel pipe welding temperature changes,residual stress distribution,different processes residual stress changes in the law,the prediction of post-weld residual stress distribution and deformation are studied in this paper.The results show that the temperature field values and test results are more consistent with the accuracy of numerical simulation of welding,the welding process is mainly in the form of heat transfer;Residual high stresses are predominantly distributed in the Fusion zone(FZ)and Heat-affected zone(HAZ),with residual stress levels tending to decrease from the center of the weld along the axial path,the maximum stress appears in the FZ and HAZ junction;The number of welding layers has an effect on the residual stress distribution,the number of welding layers increases,the residual stress tends to decrease,while the FZ and HAZ high stress area range shrinks;Increasing the number of plies will increase the amount of residual distortion.

Seismic behavior of concrete filled steel tubular arch structures

Shaking table tests of a 1:10 scale arch model performed to investigate the seismic behavior and resistance of concrete filled steel tubular (CFT) arch structures are described in this paper. The El-Centro record and Shanghai artificial wave were adopted as the input excitation. The entire test process can be divided into three stages depending on the lateral brace configurations, i.e., fully (five) braced, two braces removed, and all braces removed. A total of 46 tests, starting from the elastic state to failure condition, have been conducted. The natural vibration frequencies, responses of acceleration, displacement and strain were measured. From the test results, it is demonstrated that the CFT arch structures are capable of resisting severe ground motions and that CFT arches offer a credible alternative to reinforced concrete arches, especially in regions of high seismic intensity.

Approach for analyzing the ultimate strength of concrete filled steel tubular arch bridges with stiffening girder

A convenient approach is proposed for analyzing the ultimate load carrying capacity of concrete filled steel tubular (CFST) arch bridge with stiffening girders. A fiber model beam element is specially used to simulate the stiffening girder and CFST arch rib. The geometric nonlinearity, material nonlinearity, influence of the construction process and the contribution of prestressing reinforcement are all taken into consideration. The accuracy of this method is validated by comparing its results with experimental results. Finally, the ultimate strength of an abnormal CFST arch bridge with stiffening girders is investigated and the effect of construction method is discussed. It is concluded that the construction process has little effect on the ultimate strength of the bridge.

Wind Vibration Study of Long-span Steel Arch Structure of Beijing Capital International Airport

The wind-induced dynamic response of long-span light-weight steel arch structure of the global transportation center (GTC) of Beijing Capital International Airport was studied. A composite technique with combination of WAWS(Weighted Amplitude Wavelet Superposition) and FFT(Fast Fourier Transformation) was introduced to simulate wind velocity time series of hundreds of spatial points simultaneously. The structural shape factors of wind load was obtained from wind tunnel model test. The wind vibration factor based on structural displacement response was investigated. After comparing the computational results with wind tunnel model test data, it was found out that the two results accord with each other if wind comes from 0° direction angle, but are quite different if wind comes from 180° direction angle in the area blocked off by airport terminals. The possible reasons of this difference were analyzed. Haar wavelet was used to transform and analyze wind velocity time series and structural wind-induced dynamic responses. The relationship between exciting wind loads and structural responses was studied in time and frequency domains.

Concrete-Filled Steel Tube Arch Bridges in China

In the past 20 years, great progress has been achieved in China in the construction of concrete-filled steel tube （CFST） arch bridges and concrete arch bridges with a CFST skeleton. The span of these bridges has been increasing rapidly, which is rare in the history of bridge development. The large-scale construction of expressways and high-speed railways demands the development of long-span arch bridges, and advances in design and construction techniques have made it possible to construct such bridges. In the present study, the current status, development, and major innovative technologies of CFST arch bridges and concrete arch bridges with a CFST skeleton in China are elaborated. This paper covers the key con- struction technologies of CFST arch bridges, such as the design, manufacture, and installation of steel tube arch trusses, the preparation and pouring of in-tube concrete, and the construction of the world＇s longest CFST arch bridge-the First Hejiang Yangtze River Bridge. The main construction technologies of rein- forced concrete arch bridges are also presented, which include cable-stayed fastening-hanging cantilever assembly, adjusting the load by means of stay cables, surrounding the concrete for arch rib pouring, and so forth. In addition, the construction of two CFST skeleton concrete arch bridges-the Guangxi Yongning Yong River Bridge and the Yunnan-Guangxi Railway Nanpan River Bridge--is discussed. CFST arch bridges in China have already gained a world-leading position; with the continuous innovation of key technologies, China will become the new leader in promoting the development of arch bridges.

A Survey of Steel Arch Bridges in China

A review of the current status and progress of steel arch bridges in China is presented in this paper. The existing steel arch bridges in China were analyzed in terms of steel material, span, structure type, main arch rib form and construction method. The comparison with CFST arch bridges and RC arch bridges is also conducted. It is shown that steel arch bridge has gain rapid development in China since 2000, characterized by long main spans. As for the span, most of the steel arch bridges have a span less than 250 m, while when the span exceeds 350 m, steel arch bridges are strongly competitive against CFST or RC arch bridges. Over 80% of the bridges are through and half-through bridge types, and the arch ribs are hingeless structures. The rise-to-span ratios of the arches are mainly between 1：4 and 1： 5. Most of the arches use solid box ribs, and a small portion of arches use truss ribs in which box sections are mostly adopted for the truss members. The cantilever method and scaffolding method are the two main construction methods used, but some other construction methods have also been developed.

Aφ6-m Tunnel Boring Machine Steel Arch Splicing Manipulator

Robotic splicing of steel arches is a challenging task that is necessary to realize the grasping and docking of steel arches in a limited space.Steel arches often have a mass of more than 200 kg and length of more than 4 m.Owing to the large volume and mass of steel arches and the high requirements for accurately positioning the splicing,it is difficult for a general manipulator to meet the stiffness requirements.To enhance the structural stiffness of the steel arch splicing manipulator,a single-degree-of-freedom(DOF)closed-loop mechanism was added to the grasping structure of the manipulator.Based on the basic principle of structural synthesis,a solution model of the single-DOF closed-loop mechanism was developed,and alternative kinematic pairs of the mechanism with different input constraints and output requirements were derived.Based on this model,a design method for a single-DOF closed-loop grasping mechanism and a posture adjustment mechanism for a steel arch was devised.Combined with the same dimensional subspace equivalence principle of the graphical-type synthesis method,12 types of steel arch splicing manipulator were constructed.By analyzing the motion/force transmission and structural complexity of the steel arch splicing manipulators,the best scheme was selected.A prototype of the steel arch splicing manipulator was manufactured.Adams software was used to obtain clearly the output trajectory of the end of the manipulator.The relative spatial positions of the upper and lower jaws under different working stages were analyzed,demonstrating that the manipulator satisfied the grasping requirements.Through a steel arch splicing experiment,the grasping effect,docking accuracy,and splicing efficiency of the manipulator met the design requirements.The steel arch splicing manipulator can replace the manual completion of the steel arch splicing operation,significantly improving the operation efficiency.

In-Plane Creep Buckling of Concrete-Filled Steel Tubular Arches

The creep-induced deformation of the arch rib of concrete-filled steel tubular （CFST） arches under a sustained load can increase the bending moment, which may lead to earlier stability failure called creep buckling. To investigate the influences of concrete creep on the buckling strength of arches, a theoretical analysis for the creep buckling of CFST circular arches under distributed radial load is performed. The simplified Arutyunyan-Maslov （AM） creep law is used to model the creep behavior of concrete core, and the creep integral operator is introduced. The analytical solutions of the time-dependent buckling strength under the sustained load are achieved and compared with the existing formula based on the age-adjusted effective modulus method （AEMM）. Then the solutions are used to determine the influences of the steel ratio and the first loading age on the creep buckling of CFST arches. The results show that the analytical solutions are of good accuracy and applicability. For CFST arches, the steel ratio and the first loading age have significant influences on creep buckling. An approximate log-linear relationship between the decreased degrees of the creep buckling strength and the first loading age is found. For the commonly used parameters, the maximum loss of the buckling strength induced bv concrete creen is close to 40%

Analysis of Key Technologies in the Design of Small and Medium Span Basket Type Steel Box Tied Arch Bridge

In order to ensure the construction quality and safety of small and medium span basket type steel box tied arch bridge,this paper takes a practical project as an example to analyze the key technologies in its design process.It is hoped that this analysis can provide corresponding reference for the design and construction of this kind of arch bridge.

Seismic response of the long-span steel truss arch bridge with the thrust under multidimensional excitation

Purpose–Under different ground motion excitation modes,the spatial coupling effect of seismic response for the arch bridge with thrust,seismic weak parts and the internal force components of the control section of main arch ribs are analyzed.Design/methodology/approach–Taking a 490 m deck type railway steel truss arch bridge as the background,the dynamic calculation model of the whole bridge was established by SAP2000 software.The seismic response analyses under one-,two-and three-dimension(1D,2D and 3D)uniform ground motion excitations were carried out.Findings–For the steel truss arch bridge composed of multiple arch ribs,any single direction ground motion excitation will cause large axial force in the chord of arch rib.The axial force caused by transverse and vertical ground motion excitation in the chord of arch crown area is 1.4–3.6 times of the corresponding axial force under longitudinal seismic excitation.The in-plane bending moment caused by the lower chord at the vault is 4.2–5.5 times of the corresponding bending moment under the longitudinal seismic excitation.For the bottom chord of arch rib,the arch foot is the weak part of earthquake resistance,but for the upper chord of arch rib,the arch foot,arch crown and the intersection of column and upper chord can all be the potential earthquake-resistant weak parts.The normal stress of the bottom chord of the arch rib under multidimensional excitation is mainly caused by the axial force,but the normal stress of the upper chord of the arch rib is caused by the axial force,in-plane and out of plane bending moment.Originality/value–The research provides specific suggestions for ground motion excitation mode and also provides reference information for the earthquake-resistant weak part and seismic design of long-span deck type railway steel truss arch bridges.

瓮马铁路乌江特大桥设计关键技术研究

新建瓮马铁路乌江特大桥跨越两山之间深谷,地形复杂、设计难度大。为研究该桥梁方案,首先阐述了主桥的方案构思和结构设计,然后通过空间有限元软件对本桥进行静、动力仿真分析,总结了大跨铁路劲性骨架混凝土拱桥构造和受力特性。结果表明:主跨337 m上承式劲性骨架混凝土拱桥具有刚度大、徐变小、后期养护维修工作量小等优点,主拱圈采用小矢跨比设计,兼顾安全、经济、环保和美观,能够满足铁路桥梁跨越山区“V”形峡谷的要求;主拱圈由劲性钢管混凝土骨架外包C55无收缩混凝土构成,通过分层分段浇筑方案改善拱圈各构件的内力;拱上结合梁采用两片工字形钢与混凝土桥面板相结合的形式,钢梁栓焊结合,便于制造、运输和施工;拱座采用梯形断面扩大基础,基础开挖永临结合,有效降低施工风险;数值分析表明该桥结构的刚度、强度、稳定性均能满足规范要求,能够满足客货共线铁路的安全性和乘坐舒适性要求。可为其他山区铁路桥梁桥式研究提供参考。

大倾角钢箱提篮拱桥总体设计

考虑施工技术、经济性和景观效果等方面,陕西蔡家坡渭河特大桥主桥采用(35+210+35) m大倾角钢箱提篮拱桥。该桥采用摩擦摆和环向钢丝绳阻尼支座综合减隔震约束体系,以降低结构的地震响应。拱肋为单室等宽钢箱截面,采用主、副拱肋2条悬链线,主、副拱肋共面,设计为横向内倾20°的大倾角,在提高桥梁景观效果的同时,又有效提高了结构的整体稳定性;拱肋设钢-混结合段连接拱脚与混凝土拱座。桥面系采用自重较轻的正交异性钢桥面板结构。吊杆采用抗拉强度1 860 MPa的环氧柔性钢绞线。基础采用Φ2.5 m的钻孔灌注群桩,以抵抗软弱地质条件下荷载的竖向及水平作用力。该桥总体采用先梁后拱的施工方案。整体及局部有限元分析结果表明,桥梁结构力学性能均满足规范要求,设计安全可靠。

基于点云切片算法的铁路钢桁拱桥线形分析

铁路桥梁线形测量对于桥梁健康检测与确保铁路安全运营具有重要作用。为提高运营铁路钢桁拱桥线形测量效率,以某3跨钢桁拱桥为例,运用地面激光扫描(TLS)技术对桥梁杆件进行整体化扫描,从桥梁线形测量精度、扫描完整性、点云个数等3方面,分析出最佳的桥梁扫描测站数为10个。运用3DNDT点云配准算法将各测站一一配准,桥梁点云配准精度为2 mm,将桥梁点云投影至xoy平面,用半径滤波器进行噪声点的去除,得到完整“纯净”的桥梁点云模型。提出点云等距切片与点云平面切片算法提取桥梁线形,并将线形点云数据导出在AutoCAD中拾取坐标。将点云切片法提取的TLS测量值、全站仪法测量结果与原始成桥线形做比较分析,结果表明:在桥面线形分析中,两方法均在跨中处A5点测量出最大变形,分别为12.69 mm、10.29 mm,两方法的最大相互较差R为2.4 mm,相关系数优于99.93%;在拱轴线线形分析中,点云切片法与全站仪法在主桁上弦跨中B4点位测量的最大变形为6.2 mm、3.9 mm,在主桁下弦跨中B10点位测量的最大变形为5.9 mm、3.5 mm,两方法的最大互相较差R为3.2 mm,相关系数优于99.87%,验证了点云切片算法的有效性与TLS测量的高精度性。拱轴线横向线形未出现明显侧移,点云等距切片得到的19个吊杆垂直度保持良好,未发生扭转与偏移。该成果对于运营铁路钢桁拱桥的线形分析与点云处理方法可提供相应的思路和参考,具有重要的实用价值。

波纹钢形状与拱效应对加固盖板涵承载力的影响

为了探索波纹钢形状对加固盖板涵承载力的影响及填充混凝土的拱效应形成机制,采用室内试验与数值分析相结合的研究方法,以一个室内模型试验结果为基准,建立了72个箱形、圆弧及其之间的过渡形状的波纹钢加固盖板涵的数值模型,探明了加固体系承载力随波纹钢形状参数的变化规律;基于合理拱轴的概念,探明了填充混凝土的拱效应形成机理,并采用5个数值模型进行了验证。结果表明:拱腋半径保持不变时,加固体系的承载力随着拱顶、侧墙半径的增加而减小;拱顶、侧墙半径不变时,加固体系的承载力随着拱腋半径的增加而增大;提升加固体系承载力最有效的方式是增加拱腋半径,其次是减小拱顶和侧墙半径;填充混凝土的拱效应与荷载类型有关,当波纹钢的形状能保持拱轴连续并且在素混凝土刚性角以内时,加固体系的承载力最高。在设计波纹钢加固盖板涵结构时,应根据实际工程需要综合考虑波纹钢形状与填充混凝土的拱效应,尽量避免紧贴原盖板涵的加固设计。

方拱形波纹钢管廊弯矩解析解及断面参数研究

方拱形结构因空间利用率较高而广泛应用于我国地下综合管廊的建设中,但其结构承载特征、力学机制及相关设计方法研究尚少。为研究方拱形波纹钢管廊结构弯矩的解析计算理论以及合理的断面形式,利用结构力学、土力学基本理论和相关规范,推导方拱形波纹钢综合管廊的弯矩解析解,并用二维平面应变模型对弯矩解析式的正确性进行验证,同时建立不同管顶覆土深度的方拱形波纹钢管廊三维地层-结构有限元数值模型,将数值分析结果与弯矩解析式计算的弯曲应力进行对比,分析弯矩表达式的适用覆土深度,基于弯矩解析表达式对管廊断面参数进行优化分析,并给出推荐断面参数范围。研究表明:1)方拱形波纹钢综合管廊的弯矩解析解与数值解相吻合,理论计算的弯矩与数值解的最大误差为5.79%;2)弯矩解析表达式的适用覆土深度为H≤10 m;3)针对依托工程,计算结果表明管廊断面矢跨比、顶板和侧板跨度比均处于0.6~0.8,管廊结构弯矩分布较合理,有利于保障结构安全。

水平往复荷载作用下钢箱提篮拱弹塑性力学性能研究

目的 探究倾角、矢跨比及宽跨比三个参数对钢箱提篮拱在水平往复荷载作用下力学性能的影响,为钢提篮拱桥抗震设计提供理论基础。方法 通过改变参数,建立54个钢箱提篮拱有限元模型,在水平往复荷载作用下进行滞回分析,研究钢箱提篮拱水平力-位移滞回性能、极限承载力和拱顶横撑内力、变形在不同参数条件下的变化规律。结果 随着拱肋倾斜角度、宽跨比的增加或矢跨比的减小,结构初期刚度、极限承载能力均有较大提高,但横撑内力也随之增加,并会产生局部失稳破坏,影响结构的承载能力。结论 增加拱肋倾斜角度对钢箱提篮拱横向力学性能有较大改善,但在设计时应注意横撑内力增加带来的不利影响。

车辆荷载作用下钢-混凝土组合梁疲劳应力分析

【目的】随着桥梁服役期延长和车辆荷载增加等多种因素的影响,结构承载力会变得越来越弱,疲劳寿命不断降低,最终可能导致低应力疲劳破坏。因此有必要对车辆荷载下拱桥钢混组合梁的疲劳细节应力进行研究。【方法】采用数值模拟的方法,利用Midas FEA NX软件建立3个标准长度的三维实体精细有限元模型,分析钢混组合梁易损疲劳关键点的位置,并研究车辆荷载横向最不利加载位置和纵向加载下的疲劳细节应力变化规律。【结果】结果表明,组合梁次横梁与中纵梁交点处有三处疲劳关键点;靠近桥梁中线位置是车辆荷载下钢梁疲劳最不利的横向加载位置;四种不同标准的纵向车辆加载时,三个疲劳关键点均出现两次应力峰值,且最大应力幅值均低于常幅疲劳强度的极限值。【结论】研究成果可为钢-混凝土组合梁试验和相关研究提供参考。

100 m~150 m跨混凝土拱桥基于特定钢拱架的预拱度快速计算方法

针对100 m~150 m跨混凝土拱桥所采用的特定钢拱架的预拱度计算问题,提出了一种用拱圈自重变形和钢拱架变形比值快速计算钢拱架预拱度的方法。为了得到不同矢跨比和拱轴系数下的钢拱架变形比值,编写了通过导入MCT文件建立Midas/Civil有限元模型的辅助程序,实现从单元、边界条件、施工阶段和施工阶段联合截面定义的全过程快速建模,对拱圈混凝土分底板、腹板、顶板三环浇筑,考虑钢拱架与拱圈的联合作用,给出了钢拱架预拱度计算公式。计算结果表明,对于常用矢跨比和拱轴系数的混凝土拱桥,拱圈分环浇筑变形与拱圈自重变形比值的平均值为4.37~4.88,为方便钢拱架弹性变形计算,建议变形比值统一取5.0。将该方法应用于一座净跨径为135 m的混凝土拱桥钢拱架预拱度计算中,得到的钢拱架弹性变形与空间模型结果最大误差为4.30%,满足工程精度要求,表明该方法合理可行,可在混凝土拱桥钢拱架预拱度计算中推广应用。

曲线条件大跨度拱加劲连续梁设计

贵南高铁二塘双线特大桥采用90m+180m+90m拱加劲连续梁结构。大桥位于曲线上,梁体采用分段直线布置,悬灌施工;主拱采用哑铃形钢管混凝土拱肋,钢管直径1 m,拱肋全高3 m;采用整束挤压钢绞线吊杆,全桥拱设置36组吊杆;纵向活动主墩通过构造措施,形成半刚构结构体系,限制部分梁体问题伸缩变形;大桥采用先悬灌主梁,后在主梁上搭设支架原位拼装拱肋方式施工。经论文研究计算结果表明,该桥刚度、受力等均满足规范要求。

考虑高阶振型效应的大跨度钢桁拱桥瑞利阻尼参数取值研究

为了解高阶振型效应对大跨度钢桁拱桥地震反应的影响机制,以及在采用直接积分法时构建合适的瑞利阻尼矩阵,以某490 m跨径钢桁拱桥为背景,采用SAP 2000软件建立全桥弹性动力计算模型。针对主拱圈上(下)弦杆轴力、弯矩,研究振型参与质量最大的7阶(第1、4、8、11、13、23、49阶)振型反应与总反应的占比关系,并对构建瑞利阻尼矩阵的特征频率选取方法展开研究。结果表明:主拱圈上、下弦杆拱脚区域的轴力主要由1阶振型(第1阶)控制,由拱脚向拱顶过渡,逐渐转变为由2~4阶振型控制,高阶振型效应显著;同一阶振型对主拱圈上、下弦杆轴力贡献率及分布规律的影响不同;对于复杂钢桁拱桥,采用振动方向上振型参与质量较大的2阶振型特征频率构建瑞利阻尼矩阵可能因高估了高阶振型阻尼比,导致除拱脚区域以外的拱圈弦杆杆件轴力计算结果偏小,结构偏于不安全;采用直接积分法对复杂钢桁拱桥进行地震反应分析时,建议选取多阶控制振型构建相应的瑞利阻尼工况,并对其计算结果取包络用于抗震设计。