Effect of titanium on the sticking of pellets based on hydrogen metallurgy shaft furnace:Behavior analysis and mechanism evolution

Direct reduction based on hydrogen metallurgical gas-based shaft furnace is a promising technology for the efficient and low-carbon smelting of vanadium-titanium magnetite.However,in this process,the sticking of pellets occurs due to the aggregation of metal-lic iron between the contact surfaces of adjacent pellets and has a serious negative effect on the continuous operation.This paper presents a detailed experimental study of the effect of TiO2 on the sticking behavior of pellets during direct reduction under different conditions.Results showed that the sticking index(SI)decreased linearly with the increasing TiO2 addition.This phenomenon can be attributed to the increase in unreduced FeTiO3 during reduction,leading to a decrease in the number and strength of metallic iron interconnections at the sticking interface.When the TiO2 addition amount was raised from 0 to 15wt%at 1100°C,the SI also increased from 0.71%to 59.91%.The connection of the slag phase could be attributed to the sticking at a low reduction temperature,corresponding to the low sticking strength.Moreover,the interconnection of metallic iron became the dominant factor,and the SI increased sharply with the increase in re-duction temperature.TiO2 had a greater effect on SI at a high reduction temperature than at a low reduction temperature.

An Artificial Intelligence Algorithm for the Real-Time Early Detection of Sticking Phenomena in Horizontal Shale Gas Wells

Sticking is the most serious cause of failure in complex drilling operations.In the present work a novel“early warning”method based on an artificial intelligence algorithm is proposed to overcome some of the known pro-blems associated with existing sticking-identification technologies.The method is tested against a practical case study(Southern Sichuan shale gas drilling operations).It is shown that the twelve sets of sticking fault diagnostic results obtained from a simulation are all consistent with the actual downhole state;furthermore,the results from four groups of verification samples are also consistent with the actual downhole state.This shows that the pro-posed training-based model can effectively be applied to practical situations.

Assessment of Knowledge, Attitude and Practices among Healthcare Workers in a Tertiary Care Hospital on Needle Stick Injury

Purpose: Needle-stick injury (NSI) is one of the most potential occupational hazards for healthcare workers because of the transmission of blood-borne pathogens. As per recent data, around 30 lakh healthcare workers sustain Needle stick injuries each year. This study was conducted to assess healthcare workers’ knowledge, attitude and practices regarding needle stick injury. Materials & Methods: A cross-sectional study was conducted in a Tertiary Care Hospital over the period of 3 months. The study population consisted of Intern Doctors, Post Graduate resident Doctors, Staff Nurses, laboratory technicians of Government Medical College and New Civil Hospital, Surat (n = 300). The data were collected using a self-administered questionnaire via the means of Google Forms. Questionnaire was made with prior review literature. The data obtained were entered and analysed in Microsoft Excel. Results: The prevalence of NSI in our study was 46%, with a higher prevalence among the PG residents (72%). Overall scores regarding knowledge and attitude were better in PG residents (knowledge score > 7 in 71% and Attitude Score > 7 in 68% of PG Residents). Even though the PG residents scored highest in the knowledge category, the majority of them suffered needle stick injuries as a result of poor practice scores. Among those who had NSI (n = 139/300), 70% of study participants had superficial injuries, only 9% reported the incident, 18% got medical attention within 2 hours of the incident, and 7% followed up to recheck their viral markers status. Most incidents of NSI were due to hypodermic needles while recapping needles. Conclusion: Exposure to needle stick injuries and their underreporting remains a common problem. It is imperative that healthcare workers receive regular training on the proper handling of sharp objects. We can also draw the conclusion that preventing NSIs requires putting knowledge into practice.

Effect of Mouth Opening Training Stick Combined with Oral Massage on Mouth Opening Difficulty in Head and Neck Cancer Patients after Treatment

Objective: To study the application effect of mouth-opening training sticks combined with oral massage on patients with mouth-opening difficulty after treatment for head and neck cancer. Methods: Using convenient sampling, 60 patients with mouth-opening difficulty after treatment for head and neck cancer admitted to the Oncology Department from February 2022 to October 2023 were selected for a 2-week exercise and nursing program. The patients were divided into a control group (February 1, 2022 to November 30, 2022) and an observation group (December 1, 2022 to October 31, 2023), with 30 patients in each group. The control group underwent routine mouth-opening functional exercises combined with cork for oral support training, while the observation group underwent routine mouth-opening functional exercises combined with oral massage and mouth-opening training sticks for oral support training. The mouth-opening degree, mouth-opening difficulty level, comfort level, compliance, and quality of life were observed in both groups. Results: Before the intervention, there were no statistically significant differences in mouth-opening degree and mouth-opening difficulty level between the two groups (P > 0.05). After the intervention, the mouth-opening degree, mouth-opening difficulty level, oral comfort level, compliance, and QLICP-HN scores in the observation group were all better than those in the control group, with statistically significant differences (P < 0.05). Conclusion: The combination of mouth-opening training sticks and oral massage with mouth-opening functional exercises can effectively improve the degree of mouth-opening difficulty, enhance oral comfort, increase compliance with mouth-opening exercises, and improve quality of life.

Effects of Plant Spacing and Finger Sticking Area Settings for Machine Transplanting on Yield of Double-season Early Rice

The effects of rice transplanters＇ transplanting settings（plant spacing and finger sticking area） on rice yield were investigated in two early-season rice cultivars：hybrid rice cultivar（Zhuliangyou 819） and conventional rice cultivar（Zhongjiazao 17）.The results showed that,different transplanting settings resulted in different numbers of transplanted basic seedlings,and the rice yield was significantly correlated with the number of transplanted basic seedlings.The number of transplanted basic seedlings increased with the decrease of plant spacing and the increase of finger sticking area.The rate of lost hills of machine transplanting decreased with the increase of finger sticking area.The leaf area index and amount of dry matter accumulation were highly correlated with the number of transplanted basic seedlings.The average yield of the rice transplanted with a plant spacing of11.5 cm was higher than that with a plant spacing of 13.8 cm.In the field transplanted with the rice under the plant spacing of 13.8 cm,the rice yield increased with the increase of finger sticking area,and the finger sticking area of 2.23 cm2 showed the highest rice yield of 8 174.16 kg/hm2 of Zhuliangyou 819 and 7 925.54kg/hm2 of Zhongjiaozao17.In the field transplanted with the rice under the plant spacing of 11.5 cm,the rice yield was the highest with the finger sticking area of 1.83 cm2,and then decreased with the large finger sticking area.Under the plant spacing of 11.5 cm,the highest rice yields of Zhuliangyou 819 and Zhongjiaozao17 were 8 492.94 kg/hm2 and 8 000.23 kg/hm2,respectively.Therefore,the preferred machine transplanting settings for double-season early rice are a plant spacing of11.5 cm and a finger sticking area of 1.83 cm2,while the finger sticking area should be increased to 2.23 cm2 for conventional rice cultivars.

APPLICATION OF 2-D MOIRE INTERFEROMETRYOF STICKING FILM IN HUMAN TIBIA MEASUREMENT

This paper makes use of the method of testing and measuring the human body tibia by using2-D moire interferometry of sticking film. hased on the J'--y direction moire patterns recorded synchronously by 2-D optical path,the elastic constant,strain and displacement of the tibia are measured.Compared with the electric measuring method the error is samll and the sensitivity is high.

Test research on sticking mechanism during hot rolling of SUS 430 ferritic stainless steel

The sticking phenomenon during hot rolling of SUS 430 ferritic stainless steel was investigated by means of a two-disc type high-temperature wear tester. The test results indicate that sticking particles on the surfaces of high chromium steel （HiCr） and high-speed steel （HSS） rolls undergo nucleation, growth, and saturation stages. Grooves on the roll surface generated by grinding provide nucleation sites for sticking particles. The number of sticking particles on the HiCr roll surface is greater than that on the HSS roll surface. The average surface roughnesses （Ra） of HiCr and HSS rolls change from 0.502 and 0.493 μm at the initial stage to 0.837 and 0.530 μm at the saturation stage, respectively. The test further proves that the sticking behavior is strongly dependent on roll materials, and the HSS roll is more benefi- cial to prevent particles sticking compared with the HiCr roll under the same hot-rolling conditions.

Sticking of iron ore pellets in direct reduction with hydrogen and carbon monoxide:Behavior and prevention

A series of reduction experiments of iron ore pellets with hydrogen,carbon monoxide and their mixture were carried out in a laboratory scale shaft furnace.The sticking behavior accompanying reduction of iron ore pellets was investigated.And morphology of the sticking interface forming during reduction was analyzed by SEM equipped with EDS.In order to evaluate the effects of the temperature and gas composition on sticking properties,reduction of iron ore pellets were conducted at 800-1000 ℃.The results show that the sticking strength of the pellets increases with temperature,however,decreases with hydrogen content in reducing gas.For an efficient shaft furnace operation in direct reduction(DR),relative prevention of sticking such as coating of pellets was also developed to solve sticking problem.The results show that CaO is a suitable material for the coating method.

Wall Sticking of High Water-Cut, Highly Viscous and High Gel-Point Crude Oil Transported at Low Temperatures

Some crude oils with high water cut have the capability to flow below the oil gel point, while the oil particles adhere to the pipe wall in the form of paste, also called "wall sticking". Wall sticking is a serious problem during the pipeline transportation, leading to partial or total blockage of the pipeline and energy wastage. In this paper, a series of laboratory flow loop experiments were conducted to observe the wall sticking characteristics of crude oil with high water cut, high viscosity and high gel point at low transportation temperatures. The effects of shear stress and water cut on the wall sticking rate and occurrence temperature were investigated. Experimental results indicated that the wall sticking rate and occurrence temperature were lower under stronger shear stress and higher water cut conditions. A criterion of wall sticking occurrence temperature(WSOT) and a regression model of wall sticking rate were then established. Finally, the software was developed to calculate the pressure drop along the pipelines of crude oils with high water-cut. It was able to predict the wall sticking thickness of gelled oil and then calculate the pressure drop along the pipelines. A typical case study indicated that the prediction results obtained from the software were in agreement with actual measured values.

闭合复位内固定联合joy stick操纵杆技术治疗儿童难复性肱骨髁上骨折效果观察

目的观察闭合复位内固定联合joy stick操纵杆技术治疗儿童难复性肱骨髁上骨折的临床效果。方法选择因“肘关节外伤后肿痛伴活动受限”入院患儿4例,均诊断为GartlandⅢ型肱骨髁上骨折,均采用闭合复位内固定联合joy stick操纵杆技术治疗。结果4例患儿均获得满意复位,无一例转为切开复位,平均手术时间66 min,住院时间均<5 d。出院后规律复查换药,1月后均恢复良好,骨折线对位满意,未出现感染等短期并发症,拔除克氏针。结论Joy stick操纵杆技术不仅可以更加准确地控制肱骨轴的旋转,还能更快地获得复位和维持复位,进针顺利,手术时间短,减少转为切开复位,降低手术难度,且未增加围手术期并发症。

A New Method for Predicting Wall Sticking Occurrence Temperature of High Water Cut Crude Oil

In crude oil transportation, adhesion of oil on pipe wall can cause partial or total blockage of the pipe. This process is significantly affected by wall sticking occurrence temperature(WSOT). In this work, an efficient approach for estimating WSOT of high water-cut oil, which can agree well with the actual environment of multiphase transportation pipeline, is proposed. Based on the energy dissipation theory, it is possible to make comparison of average shear rates between the stirred vessel and the flow loop. The impacts of water content and shear rate on WSOT are investigated using the stirred vessel and the flow loop. Good agreement has been observed between the stirred vessel and the flow loop results with the maximum and the average absolute deviations equating to 3.30 °C and 2.18 °C, respectively. The development of gathering scheme can enjoy some benefits from this method.

Influence of Oil and Water Components on Wall-sticking Occurrence Temperature in High Water-cut Crude Oil Pipeline

To study the wall-sticking phenomenon and prevent pipeline blockage accidents,two analytical methods are used to evaluate the influence of different crude oil components on the wall-sticking occurrence temperature(WSOT).The WSOT and the interactions among oil,water,and surface solids are measured and calculated by various devices under different values of the wax content,water pH,and salinity.The results show that there is greater correlation between the wax content and WSOT than between resins/asphaltenes and WSOT.Furthermore,the wax content,water pH,and salinity have different effects on WSOT.There is generally a positive correlation between wax content and WSOT,whereas the maximum WSOT occurs when the water pH is in the range 5.7–6.5,and decreases under more acidic or alkaline conditions.As the salinity increases,WSOT decreases slightly,but quickly becomes saturated.In terms of interactions,variations in the interfacial tension and adhesion work with pH and salinity are consistent with that of WSOT,while the contact angle exhibits the opposite relation.

Operational procedures of auricular point sticking technology

As an external treatment technique of traditional Chinese medicine(TCM),auricular point sticking,which is rooted in holographic biology theory and TCM viscera and meridian theory,is a safe and effective treatment method.This article introduces the technology overview and development process.The auricular point sticking technique for constipation is taken as an example to specify the basic requirements,assessment,operational points,acupoint selection and matters needing attention during the implementation of the auricular acupressure technique,providing a reference for the operating procedures of this technique in the clinical treatment of other diseases such as insomnia,diarrhea,colds,hypertension,headache,and dysmenorrhea.

Modeling and simulation of solvent behavior and temperature distribution within long stick propellants with large web thickness undergoing drying

Drying is a complicated physical process which involves simultaneous heat and mass transfer in the removal of solvents inside propellants.Inappropriate drying techniques may result in the formation of a hard skin layer near the surface to block the free access of most solvent through for long stick propellants with large web thickness,which lead to lower drying efficiency and worse drying quality.This study aims to gain a comprehensive understanding of drying process and clarify the mechanism of the blocked layer near the propellant surface.A new three-dimensional coupled heat and mass transfer(3D-CHMT)model was successfully developed under transient conditions.The drying experiment results show that the 3DCHMT model could be applied to describe the drying process well since the relative error of the content of solvent between simulation and experiment values is only 5.5%.The solvent behavior simulation demonstrates that the mass transfer process can be divided into super-fast(SF)and subsequent minorfast(MF)stages,and the SF stage is vital to the prevention of the blocked layer against the free access for solvent molecules inside propellant grains.The effective solvent diffusion coefficient(Deff)of the propellant surface initially increases from 3.4×10^(-6)to 5.3×10^(-6)m^(2)/s as the temperature increases,and then decreases to 4.1×10^(-8)m^(2)/s at 60-100 min.The value of Deffof surface between 0-1.4 mm has a unique trend of change compared with other regions,and it is much lower than that of the internal at100 min under simulation conditions.Meanwhile,the temperature of the propellant surface increases rapidly at the SF stage(0-100 min)and then very slowly thereafter.Both the evolution of Deffand temperature distribution demonstrate that the blocked layer near the propellant surface has been formed in the time period of approximately 0-100 min and its thickness is about 1.4 mm.To mitigate the formation of blocked layer and improve its drying quality of finial propellant products effectively,it should be initially dried at lower drying temperature(30-40℃)in 0-100 min and then dried at higher drying temperature(50-60℃)to reduce drying time for later drying process in double base gun propellants.The present results can provide theoretical guidance for drying process and optimization of drying parameters for long stick propellants with large web thickness.

Numerical Simulation and Prediction for Sticking Type Breakout Behavior in Slab Contiuous Casting

A two-dimensional heat transfer model was developed to calculate the mould wall temperature field under normal operations condition and to determine its changing behavior when breakout occured. On the numerical simulation of sticking type breakout process and the breakout related wall temperature evolution, parameters of prediction were suggested.

CLINICAL EFFECTS ON 149 CASES OF INFANTILE DIARRHEA TREATED WITH RAPID-STICKING MOXATHERAPY Attaching 35 contrasted cases with western medicine

Of 149 cases.infantile diarrhea were treated with Zhou’s multiapplied rapid-sticking herbomoxa-pen.The main acupoints selected were Auriculoapex,Tianshu(ST 25),Zusanli(ST 36),Shenshu(BL 23),etc.TWO groups were observed,32 cases from the 149 cases as therapid-sticking moxatherapy(RSMT)group who suffered from the acute diarrhea without any thera-peutics before,and the other 35 cases with western medicine as the control group.Results showedthat the recovering rate and the average therapeutic course of healing in RSMT group were higher andshorter than that in control one(P【0.05;P【0.01),even without marked difference of the total ef-fective rates between the two groups(P】0.05).Of 149 cases with RSMT,the therapeutic effect onacute ones was better than those on delayed and chronic ones(P【0.05),yet the difference was notmarked in therapeutic effects between the etiological causes of infections and non-infections(P】 0.0.5).It is therefore worthy of popularizing RSMT due to its remarked curative results without anyside-effect,simply-manipulated and well-accepted features.

Characteristics of Water Absorption and the Loss of Dust-Sticking Agent

The development of NCZ-1 dust-sticking agent was first intreduced in china. The speed of water absorption of dust-stick-ing agent was measured and studied on mining site and in laboratory, and then the law of water absorption of dust-sticking agent was analyzed. In addition, the mathematical model of the loss rate of dust-sticking agent was established by the application of fluid mechanics theory, and the method of determining the sprinkle parameters of dust-sticking agent was obtained. Through practical verifi-cation, it is found that the error of this mathematical model is less than 10%. So it can be used in the field.

Clinical Effect of Auricular Point Sticking in Patients with Lung Cancer Receiving Chemotherapy

Objective:To discuss and analyze the clinical effect of auricular point sticking in lung cancer chemotherapy.Methods:Sixty-two patients with lung cancer treated with chemotherapy in Suqian Traditional Chinese Medicine Hospital of Jiangxi Province were selected for case evaluation and analysis.The time span of the research was from June 2020 to June 2021.The patients were divided into two groups:a study group(n=31)and a control group(n=31)based on their medical record numbers.All the patients were treated with conventional western medicine before and after chemotherapy to prevent adverse reactions;however,the patients in the study group were also treated with auricular point sticking in addition to the fonner.The relevant indexes of the two groups were compared.Results:The incidence of adverse reactions was significantly lower in the study group compared to the control group(P<0.05);the rate of symptomatic relief of the patients in the study group was higher than that of the control group(P<0.05);the stress response indexes toward chemotherapy of the study group were better than those of the control group(P<0.05)・Conclusion:Auricular point sticking for patients with lung cancer who are receiving chemotherapy can reduce the incidence of adverse reactions,alleviate clinical symptoms,such as chest distress,asthma,and poor appetite,significantly alleviate stress response caused by chemotherapy,as well as promote the treatment effect;thus,it is worthy of promotion.

蜜环菌人工菌棒基质碳氮比对乌天麻产量及营养品质的影响

目的分析蜜环菌人工菌棒基质碳氮比对乌天麻产量及基本营养成分含量的影响,并对乌天麻氨基酸品质进行评价。方法通过大棚内随机区组实验,测定不同种植模式下乌天麻的基本营养成分含量,对其进行单因素方差分析和多重比较,通过氨基酸评分法对乌天麻中氨基酸营养价值进行评价。结果蜜环菌人工菌棒基质碳氮比对乌天麻的产量、基本营养成分含量及氨基酸的营养品质均有显著影响;蜜环菌人工菌棒基质碳氮比为75.94时种植的乌天麻,其各项营养指标接近对照种植的乌天麻的各项营养指标,显著大于蜜环菌人工菌棒基质碳氮比为60.69、126.39时种植的乌天麻的各项营养指标。蜜环菌人工菌棒基质碳氮比为75.94时种植的乌天麻,其必需氨基酸含量与总氨基酸含量的比值为37.03%,接近40%;必需氨基酸含量与非必需氨基酸含量的比值为58.79%,接近60%;必需氨基酸的氨基酸比值、必需氨基酸的比值系数分、必需氨基酸比值系数与联合国粮食及农业组织/世界卫生组织提出的氨基酸理想模式较接近。结论利用蜜环菌人工菌棒种植乌天麻可以获得基本营养成分含量高、氨基酸丰富、必需氨基酸的组成比例相对合理、符合人体吸收利用需求、具有较高营养价值的乌天麻。

考虑桩土间黏滑机制的桩基沉降动态特性研究

基于桩基运动控制方程,对荷载作用下的桩基沉降动态特性进行了研究。首先,考虑桩土间黏滞与滑动两种接触状态,建立了一种考虑侧阻软化及侧阻恢复的桩土相互作用模型;然后采用该模型及修正三折线模型分别模拟桩与桩侧土以及桩端土间的相互作用,结合有限差分法建立了考虑桩土间黏滑机制的桩基沉降分析方法;最后,基于建立的桩基受荷沉降分析方法,研究了桩基沉降的黏滑动态特性以及桩身的力学特性,并讨论了桩土相互作用模型中的参数对桩基沉降动态特性的影响。结果表明:当桩顶荷载接近桩基单级加载极限值,桩基沉降表现出黏滞位移与快速滑动位移交替的动态特性;桩身力学响应表现出加载路径相关性,与单级加载相比,分级加载时桩侧摩阻力能得到更好发挥,桩基极限承载力更高;提出的分析方法能够较好地模拟桩基静载试验沉降过程。